Search Documents

By J Harmse

This paper deals with the modernisation of the brakes on an electrically coupled Blair multi-rope hoist and covers the removal of the old calliper brakes and hydraulic control system, and its replacement with brake discs, disc braking units and hydraulic control systems. The paper covers the braking requirements of the hoist, which is made up of two electrically coupled single-drum hoists, together with the theory behind the choice of brakes and control systems supplied. The paper also covers the project logistics that were required in order to install and commission the new brakes and control systems with the minimum disruption to production on the only rock hoist on a major production shaft. Items covered include the modifications to civil works, pre-installation of bearing lubrication systems, brake discs and hydraulics and the interfacing of the new hydraulic control system to the existing electric control system. It had to be designed to be compatible to a new electric drive and control system due for installation at the end of 2005.

Jan 1, 2005

By M Fahey, A B. Fourie

Over the past ten years, the mining industry has witnessed the introduction of a new and innovative mine filling technique known as paste fill, which consists of placing full stream tailings with small amounts of binder and water into underground stopes. Paste fill has benefits over traditional backfill methods, such as higher solids contents than hydraulic fill and easier transportation than rock fill. From a geotechnical perspective, the behaviour of very fine material in a fully saturated state can be complex, particularly when binder is added. Previously, there has been no rigorous solution to understanding the paste fill deposition process, resulting in uncertainty regarding critical aspects such as barricade load calculations. This uncertainty has the obvious consequences of potential barricade failures (including at least 12 over the past four years), and for many operations attempts to deal with this uncertainty has led to excessively conservative filling schedules, restricting production. This paper presents an application of Minefill-2D, the first rigorous model capable of representing the paste fill deposition process. The model couples the processes of material accretion, consolidation and cement hydration to calculate the distribution of stress around a stope (including the total stress applied to barricade structures) during filling. Minefill-2D is a finite element numerical program, which has been verified using laboratory element tests, centrifuge tests and in situ measurements (Helinski, 2008). The authors present a sensitivity analysis, carried out using the model, to demonstrate some of the critical and less critical aspects relating to paste backfill deposition. The results of this sensitivity analysis are used to devise a fill management strategy that can be utilised to minimise the risk of barricade failures and maximise fill rates where appropriate.

Jan 1, 2008

By M Paakkunainen

Sampling is often the most critical part in process analysis. When the mean of a continuous lot, such as a process stream within a given time interval, is estimated by calculating the mean of several samples, the uncertainty of the estimated mean depends usually on the sampling strategy. Three different strategies can be used: systematic, stratified or random sample selection. The standard deviation of the lot mean is different for these methods so that systematic sampling usually gives the smallest and random sampling the largest standard deviation. Pierre Gy developed a method where the sampling errors of one-dimensional lots for these three strategies can be estimated from a variogram, which is calculated from a variographic experiment, ie from a set of one-dimensional time series measurements with fixed sampling interval. While variogram is an excellent tool for characterising and displaying the variability of autocorrelated processes as function of time, the sampling error estimation from it is quite laborious, however. In this work an alternative method for estimating the sampling errors was developed. The process is divided into strata of equal sizes, varying the length of strata similarly to variographic analysis. For stratified sampling the standard deviation estimates are obtained by analysis of variance and for systematic sampling by fitting a linear regression line to each stratum and calculating the residual variances. By pooling the individual variance estimates the variance estimates that are corrected for autocorrelation are obtained. The new method was tested with simulated and real data sets having periodic, random and/or drift fluctuations. For stationary processes the results agreed well with the results of the GyÆs variographic method. The method can probably be generalised to estimate the sampling variance of higher-dimensional lots.

Jan 1, 2005

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

Our modern cities are almost incapable of sustaining themselves without subsurface infrastructure, which is not identifiable at first glance. This very soon becomes evident when the chaotic conditions prevailing in some cases in the multi-million cities on the African, Asian and South American continents are taken into consideration. This does not simply apply to the hopelessly congested streets in the downtown areas. If anything, it is shown here too that a subsurface infrastructure represents an important prerequisite for public health right up to banishing the danger of disease. Even during the 1990s, this has been clearly underlined through examples of cholera and plague epidemics in parts of Central and South America as well as on the Indian subcontinent. The overriding significance of an inner urban subsurface infrastructure in order to create decent conditions in the major built-up areas was once again emphasised not all that long ago at the United Nations HABITAT-II Conference in Istanbul, Turkey, in June 1996. More than 15 000 delegates from all over the world mulled over and discussed the prerequisites for humane living conditions in human settlements taking the varying climatic, topographical and cultural marginal conditions in different regions of the globe into account. Apart from the built-up areas themselves, the utilisation of underground space is experiencing high and ever increasing significance in less densely populated regions. Attractive and fast transport links between industrial centres call for high- performance transport arteries for the economic, speedy and unhampered carriage of people and goods. Important impulses for the economic power of a region or nation are provided by transport development and links. As a consequence, tunnels for roads and railways are being built or planned to a great degree for crossing mountain ranges, rivers and straits.

Jan 1, 1999

By G Chitombo, G Lewis

The knowledge of the expected run of mine (ROM) fragmentation during the feasibility study of a green field site is essential for the design of downstream crushing and milling processes. However,the prediction of blast fragmentation can be a challenging process due to the uncertainty related to the blast design and rock mass parameters. In general,a number of possible blast designs are considered in a feasibility study,with factors such as bench height and blasthole diameter influencing the design. Rock mass parameters are normally derived from a limited number of geotechnical diamond drill cores. Although diamond drill core can provide detailed information concerning intact rock strength (unconfined compressive strength and point load),it provides limited structural information to predict the in situ block size distribution of the rock mass. The in situ block size is an essential input to the prediction of the fragmentation distribution, in particular the coarse end. This paper outlines the methodology of blast fragmentation modeling undertaken for a green field feasibility study at the Riska gold deposit in Indonesia. The favoured milling process for the feasibility study was dump leaching,with no crushing of the ore material extracted from the pit. For this reason,blast fragmentation was a critical issue to be addressed by the study. A range of blast designs were considered with bench heights and blasthole diameters ranging from 4 m to 7 m and 76 mm to 102 mm respectively. Rock mass data was obtained from 19 diamond drill cores across the deposit (total drill length approximately 2200 m). Intact rock strength was estimated from qualitative strength descriptors,while the in situ block size distribution of the rock mass was estimated from the Rock Quality Designation (RQD) of the core. The methodology of fragmentation prediction involved a number of steps including the estimation of rock mass parameters from diamond drillhole data including the estimation of the in situ block size, delineation of blast domains within the deposit,and the assessment of the impact of various blast design parameters and rock mass variation on the predicted fragmentation distribution. The modelling process for the Riska green field site highlighted the need for additional rock mass data to be collected post feasibility stage and once the development of the mine commenced.

Jan 1, 2004

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By K L. Silversides, A Chlingaryan, A Melkumyan

Multiple data sources can be fused to improve boundary modelling in stratified deposits such as the banded iron formation (BIF) hosted deposits in the Pilbara Region of Western Australia. Accurate boundaries are essential to produce high quality geological models. Initial models are based on the widely spaced exploration hole data. This creates a high level of uncertainty in areas between the holes, with different interpretations of the boundary equally probable. Including directional information collected in these holes in the models can reduce the number of possibilities. Including data collected during mining, such as blastholes and bench measurements, can further guide the model. This research demonstrates a Gaussian Processes based method of fusing these disparate data sources to better inform the boundaries. Our results demonstrate that when only exploration points are used the model creates a smooth boundary with minimal variation between the holes. Each additional data source refined the model and added additional detail to the boundary. For the blast data, the new detail projects down to the bench below the current bench to allow for a better prediction before mining commences on that bench.

Mar 22, 2022

By R L. Koenig

The rediscovery and recognition of the magnetite potential of the iron mineralisation at the Hawsons Project area 60 km south of Broken Hill has the potential for the development of a new series of magnetite iron-ore operations across the Braemar Iron Formation in New South Wales and South Australia. Despite the low-grade of 16 per cent magnetite, the Hawsons project feasibility studies are indicating a positive business case for a large-scale 20 Mt/a of magnetite project for the following reasons:• The mineralisation is on a huge scale, with a major potential for increases beyond the already very large established resource of 1.4 Bt.• The mineralisation is particularly soft for crushing and grinding, with a Bond work index of 6.3 and an overall comminution power requirement of 6.7 kWh/t of ore. This equates to 39 kWh/t of concentrate which is significantly less than for similar projects.• The mineralisation fractures easily, preferentially along grain boundaries.• Location is close to mining infrastructure and a skilled workforce at Broken Hill, 60 km to the northeast.• It is close to road and rail infrastructure for access to the resource.• A high-grade, clean magnetic concentrate can be produced, with the only contaminant being silica.The deposit is a sedimentary siltstone which is considerably different to other known magnetite deposits. This caused significant differences in Davis Tube Recovery (DTR) results between laboratories so that the softness of the ore has required a close focus on, and changes to the laboratory procedures. A DTR procedure has been developed to provide consistent results across the deposit.Crushing and grinding test work has established a clear advantage in the use of the high-pressure grinding rolls (HPGR) crushing and grinding circuit for this particular ore. The power required for comminution using the HPGR crushing circuit is about half the power required for the Autogenous milling circuit.Therefore, despite the low magnetite grades, the Braemar Iron Formation in New South Wales and South Australia has the potential be a new magnetite iron ore province.

Jul 11, 2011

By Murray G

This paper outlines the processes involved in acid generation from sulphides and the key factors in identifying and predicting time dependent changes in the nature of acid mine drainage (AMD). The initial characteristics of mine water; whether drainage from exposed mining faces, runoff and seepage from waste dumps or seepage from process tailings; do not necessarily reflect the long term potential for AMD. The ultimate quality of mine drainage is a function of the interaction of many chemical, physical, biological and engineering (operational) factors. Techniques are available that can predict the qualitative nature of acid generation and mine drainage quality but accurate quantitative predictions are essentially impossible at the present time. As more and more mining operations exploit sulphide ore, the AMD and acid waste issue will become a. far greater concern. The significance of time dependent factors in the production of acid mine drainage-.is not just restricted to particuL.ar mine sites but needs to be recognised by the mining industry as a whole.

Jan 1, 1988

The initially cautious approach taken towards ground support and reinforcement at the Porgera Underground Gold Mine in the Highlands of Papua New Guinea has evolved rapidly in the two years since stoping commenced. The confidence to continue the evolution process has grown from an increasing knowledge of mining conditions as stoping has progressed, to the extent that reinforcement requirements have decreased by 50 to 75 per cent depending on local circumstances. Changes to mining practices have significantly assisted and influenced this process.Empirical observations of ground behaviour, assisted by a deliberately selective extensometer monitoring program, provided the stimulus for early changes to ground support and reinforcement practices. Further optimisation of the ground support and reinforcement effort is being pursued through an active monitoring, measuring and analysis program. Ultimately, situation rather than site specific design will ensure continuing high quality ground support and reinforcement installations. However, local structural and lithological factors will continue to become more critical as the optimum position is reached.

Jan 1, 1993

By S Hapugoda, M Peterson, A Haileslassie, A Poliakov, E Donskoi, L Lu

Most metallic iron in the world is produced in blast furnaces from different feed stocks – sinter, lump ore and pellets. Sinter is the main iron-containing feed to the blast furnace and can constitute up to 70–85 per cent of the total ferrous burden. As sinter quality is a key element for stable blast furnace operation, the textural, chemical and physical characteristics of the sinter are very important. Two major factors that affect sinter strength are mineralogy and porosity. This study utilised optical image analysis (OIA) to characterise sinter mineralogy, and the results were compared to those obtained by manual point counting under the optical microscope.Two major mineral characteristics of iron ore sinter are the presence of primary (unreacted) and secondary (derived from melt) hematite. Standard OIA, which is based on RGB thresholding, is not able to distinguish them as they have the same reflectivity; however, primary and secondary hematite in iron ore sinter have a different morphology. The CSIRO-developed OIA software Mineral4/Recognition4 has a unique feature to identify various textures/morphologies of the same mineral. Together with other capabilities of the Mineral4/Recognition4 software, this feature was used to identify different types of hematite and silico-ferrite of calcium and aluminium and other common sinter phases, such as magnetite, larnite, glass and remnant aluminosilicates.A visual comparison of the sinter mineralogy present in optical photomicrographs and that present in the mineral maps created automatically by the Mineral4 module of the CSIRO software confirmed the accuracy of the automated mineral identification.CITATION:Donskoi, E, Hapugoda, S, Lu, L, Poliakov, A, Peterson, M and Haileslassie, A, 2015. Advances in optical image analysis of iron ore sinter, in Proceedings Iron Ore 2015, pp 543–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M D. Kuruppu

Fleet operational effectiveness is fundamental to any operation, becoming highly topical in mines experiencing less than optimal output from their fleets. It is an all encompassing aim to identify those factors that could be improved within production and suggesting solutions in order to optimise the existing fleet and obtain the highest return on capital expenditure. The fleet operational effectiveness of a large open pit truck and shovel operation in Western Australia was examined and a study was undertaken allowing identification of areas falling below target. The annualised hours and production downtimes were investigated to quantify the potential gains of improvements in these areas. The project aimed to maximise direct working hours through determination of the main issues hindering performance. External and internal factors were considered and a continuous improvement program (CIP) was developed. The CIP aimed at internal site-based improvement teams to identify and implement solutions for improvement on a day-to-day basis. Strategies were then identified for the implementation of the proposed changes.

Jan 1, 2003

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R Billingham

QueenslandÆs new safety legislation for metalliferous and coal mining (Mining and Quarrying Safety and Health Act 1999 and Coal Mining Safety and Health Act 1999, together with the Regulations) came into effect on 16 March 2001. The legislation places clear obligations on mine owners, operators and workers to have a safe place of work and to manage risks to safety and health. It also places obligations on contractors, designers and providers of services. The legislation is non-prescriptive in that it states what outcomes must be achieved and not what must be done. The key issue is that the risk of injury to people must be at an acceptable level. The legislation creates a Mines Inspectorate with powers of inspection and audit of mines, their safety management systems and the management of risks. Auditing of the risk management process is carried out against standard risk management techniques and directives for corrective action may be issued when audits reveal non-compliance or unacceptable levels of risk.

Jan 1, 2002

By F Schoenbrunn, T Laros

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to be successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings impoundment design, underflow pumping, and control system.

Jan 1, 1998

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

By Smith J. W, Hart G. N

Compositional and isotopic analyses of coal seam gases in the Southern Coalfields have shown that these gases frequently contain abnormally high concentrations of magmatically derived carbon dioxide. The size of this carbon dioxide reservoir and the extent of permeation of the sediments by carbon dioxide are not known.Therefore caution in evaluating the natural gas potential of the region is advised.

Jan 1, 1981

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022

Commissioning is one of the many phases of a project, it has inter-dependencies with the other phases, as they have amongst themselves, and has its own terminology and distinctive features. Commissioning time and cost can severely affect project economics, especially through unrealistic estimating, and requires a separate management team to ensure full control is. maintained. Targets to be achieved in commissioning are identified, together with the necessary policies to achieve them. Factors which have to be taken into account in applying these policies are Discussed.

Jan 1, 1986