Search Documents

By L Keeney

Cu-Au porphyry deposits are large tonnage low-grade resources dependent on processing large volumes of material. The ability to understand and predict comminution performance is critical, as it is frequently the rate-limiting step during processing. Parameters required from geometallurgical mapping and modelling of comminution performance are: A×b processing domains based on impact breakage variability, and BMWi processing domains showing grind response variability which lead to Mine throughput domains for a specific comminution circuit configuration. Due to the cost and/or large sample requirements of traditional comminution tests, insufficient data density and distribution of comminution indices commonly exist, making it difficult to model and map deposit scale variability. One method routinely applied to three dimensional domaining is to have an a priori zoning based on geological features (lithology, alteration, mineralogy, textures), and then apply to all material within a given domain the metallurgical values measured on a single sample or average of samples from that domain. The problem with this approach is that commonly the geological domains do not reflect comminution response, therefore compromising the quality of the average domain estimate. To resolve this problem an alternate integrated geometallurgical mapping and modelling method is applied to model and map comminution performance at Cadia East. This paper uses a data set of ~32 000 assay measurements and geological logging information, integrated with ~150 comminution measurements to analyse and develop proxy support models for comminution indices (ie A×b, BMWi, and throughput) based on inherent geological variability. Discrete downhole comminution processing domains are created, mapping orebody response while maintaining inherent variability.

Sep 5, 2011

By L C. Thompson

This paper examines six sites in Northern Nevada where soils and groundwater have been contaminated with petroleum hydrocarbons and/or organochlorine compounds. All six of the sites studied are located in an arid, highly mineralised area of the Great Basin. As a part of the original geochemical investigation to determine the applicability of biodegradation in the remediation of petroleum impacted soils and aquifers extremely high levels of uranium, vanadium and molybdenum were detected in the anaerobic groundwaters associated with some of the hydrocarbon plumes. Some groundwater uranium concentrations exceeded 7 ppm while vanadium and molybdenum concentrations reached almost one ppm. The bioleaching appeared to be most effective under methanogenic conditions and was noted in both high sulfide and low sulfide environments. Background concentrations of uranium in the formation were measured between 6 ppm and 109 ppm and highly dependent upon depth with the highest levels being found in association with evaporites. Unlike uranium, vanadium tended to concentrate in free-floating organic fractions reaching levels as high as 2000 ppm in the layers of jet fuel floating above the groundwater. Molybdenum was the most resistant of the three metals to bioleaching.

Jan 1, 2004

By A P MACONOCHIE

The methods used and some of the results obtained from a major geotechnical study of the Ok Tedi mine area, Papua New Guinea, are described. The study was carried out at both regional and local scales and extended over a two-year period. A team of individual engineers and scientists from a variety of disciplines carried out the work. This study may provide a model for other investigations in similar environments.

Jan 1, 1992

At the Waikato North Head Ironsand operation, NZ Steel Mining Ltd is using a Bucket Wheel Excavator û shiftable conveyor mining system to excavate Titanomagnetite bearing sand and clay. The system utilises two Bucket Wheel Excavators with a two level shiftable bench conveyor and common trunk conveyor to deliver the material to a processing plant. The system was commissioned in November 1984 and has proved itself to be a high capacity, low cost method of excavating. Techniques of handling high sand faces have been developed and the conveyor layouts are going through a process of change to cope with the variable geo technical conditions and remain within: the characteristics of the excavators. The safety requirements for operating the system have been of a high standard and the experience has increased the confidence of the Company and the Mines Department Inspector's, for the first Bucket Wheel Excavator Mining system in New Zealand.

Jan 1, 1986

The Broken Hill Proprietary Company Limited (BHP) started as a silver-lead-zinc mining company in Broken Hill, New South Wales, Australia in the 1880s. Since then it has diversified into the resource industries of steel, iron ore, coal, petroleum and copper. BHP World Minerals is a Business Group of BHP which is one of the worldÆs largest and most diverse mineral resource enterprises. BHP supplies raw materials for steelmaking, copper concentrate and other mineral commodities to customers in more than 45 countries. BHP World Minerals has operations spread throughout the world û in Australia, the United States, Brazil, Zimbabwe and Canada. Commodities produced by BHP World Minerals currently include silver, lead, zinc, titanium minerals, platinum group metals and coal. The BHP World Minerals Cannington silver-lead-zinc mine in Queensland, Australia is a return to the cradle of BHPÆs early silver-lead-zinc years. This paper compares the success factors and challenges at Broken Hill and Cannington.

Jan 1, 1998

The Mt. Sisa Orebody on Misima Island, P.N.G., consists of gold-silver mineralization associated with massive carbonate and amor- phous iron-manganese oxides in fractures and breccia matrix. The orebody forms the north- ern extension of the Umuna deposit. The mineralization lies within the three kilometre strike length of a northwest trending, 300 metre wide, high angle fault zone. The fault zone structure is deeply oxidi- sed, with the manganiferous oxide material resulting from oxidation of carbonate. The wallrocks are metamorphosed basement psammopelites and basic volcanic rocks, exten- sively intruded by microgranodiorite. These are dominantly epidotized and sericitized. The precious metals are associated with anomalous Cu, Zn, Pb, Mn, As, Ba, Ga, Sb, and. Mo. Many of the features of the Mt.Sisa mineralization are characteristic of volcanic- hosted epithermal deposits of western North' America. Lithologic and textural gradation is ob- served between the carbonate hydrothermal breccia-fill at Mt. Sisa, and the quartz domi- nated dilational fracture-fill mineralization which forms most of the Umuna deposit to the south. This gradational relationship is ana- logous to that within the Amethyst-OH vein system at Creede, Colorado, where it is shown to be indicative of deposition from laterally migrating fluids.

Jan 1, 1987

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999

By Riley S. J

Ranger Uranium Mine is located within the Alligator Rivers Region of the Northern Territory of Australia and surrounded by the World Heritage listed Kakadu National Park (Figure 1). The mining operation is currently producing about 1500 tonnes of uranium oxide annually, as well as considerable volumes of waste rock, low grade ore and tailings. The rehabilitation of the project should ensure that the radioactive mill tailings and other contaminants remain contained for at least 200 years, as required by the existing guidelines (Commonwealth of Australia, 1987). The present uranium mining operation is regulated by the Northern Territory Department of Mines and Energy who must refer to the Environmental Requirements when considering regulatory options. These Environmental Requirements were agreed by the

Jan 1, 1994

By J St George

Much of AucklandÆs transport infrastructure has been developed on surface with little or no consideration of underground options. Current and planned transportation routes are now facing high costs due to land values and increasing environmental resistance to surface development. The option of utilising underground space becomes a feasible investment decision for these links as well as being the only option to develop the rail network within the inner city area. Transportation tunnels offer a quieter, more energy efficient means of getting around with minimal impacts on the surface environment. One of the major impediments to tunnelling is the high construction cost, which is partly related to the risks of encountering unexpected ground conditions and/or the possibility of causing surface ground deformations which could damage structures. The geology of Auckland has had substantial investigation through various studies and projects. The sediments of the East Coast Bays Formation (ECBF) underlie most of the Auckland urban area. It is classified as a soft rock and is a suitable material to tunnel through using either a tunnel boring machine or a roadheader. This paper reviews the limited amount of tunnelling completed in the urban Auckland area, together with the international advancements that have been made in the tunnelling industry. From the known features of the local geology and the problems encountered historically, the likely risks of tunnelling in Auckland are presented and ways in which those risks could be reduced and managed, are discussed. In addition, contractual arrangements between client and contractor are assessed with respect to complicated projects (such as tunnelling), so that the risks can be managed to create efficient infrastructure routes with reduced costs.

Jan 1, 2008

By E Yurakov, D J. Ashelford, M I. Slate

The push for increasing coal production rates continues to place increasing demands on mine management to safely and effectively control seam gas. Gas drainage strategies applied vary in both effectiveness and form. Methods employed are a function of assessed risk, gas reservoir characteristics, surface and underground access, budgetary constraints and gas utilisation potential. With the aim of establishing and optimising the effectiveness and efficiency of gas drainage systems, Australian coal miners in cooperation with gas management specialists are embracing the use of gas reservoir simulators and gas emission models. This paper discusses the evolution of gas drainage practices in Australian underground coal mines and the role of gas reservoir assessment methods in optimising gas drainage systems and gas production forecasts.

Jan 1, 2005

By P R. Lock

The Silver Swan nickel mine is located at the Black Swan Nickel Project, 53 km north east of Kalgoorlie, Western Australia. The Silver Swan orebody is a massive sulphide nickel deposit dipping 70¦ east with an average in situ grade of 14 per cent. Mining of the massive orebody is by Mechanised Ramp Cut and Fill (MRCF). A mining recovery of 98 per cent and minimising dilution are primary goals in extracting the high-grade ore. Placing a distinguishable marker bed (working platform) on rock fill was identified as a key method to achieving these goals. Gravel from a pit located onsite was considered the most suitable material for the marker beds. Research undertaken to design the marker beds using the gravel revealed conventional methods used in mining would not suffice, but that road stabilisation methods could be a viable alternative. Trials used a road recycler to mix cement and gravel in situ and several test beds were constructed on the surface to determine the final design. The trials attempted to replicate a marker bedÆs life cycle of construction and placement and mucking of ore from the marker bed. Testing the marker bed for strength for use as a working platform was completed using a Clegg Hammer; good correlation to a Clegg Impact Value and the compressive strength of the stabilised gravel was found. This paper describes the use of a road stabilisation machine, tests conducted, monitoring and marker bed design and discusses underground placement of the marker bed and its performance.

Jan 1, 1998

By I A. Lamb

The Melbourne City Link Project has two tunnels, the Domain and Burnley Tunnels, which have been constructed by Transfield Obayashi Joint Venture (TOJV) under a design and construct contract. The two tunnels are located essentially under the Kings Domain, the Yarra River and, in the case of the longer Burnley Tunnel, under the inner suburb of Richmond. The Burnley Tunnel is 3.5 km long and reaches a depth of 65 m at the central Swan Street Shaft, the invert being at RL -60 m. The Domain Tunnel is 1.6 km long, with the invert reaching RL -20. The tunnels were driven, for the most part, in the siltstone and sandstone of the Silurian Age Melbourne Formation. Construction aspects of the driven tunnels as related to the engineering geology have been described by Hutchison et al (1998). The Silurian bedrock is a fractured rock aquifer that is connected to overlying alluvial aquifers. Excavation of the tunnels allowed temporary groundwater inflows which substantially de-pressurised portions of the various aquifers. This de-pressurisation provided the potential to accelerate on-going secondary consolidation rates of the Holocene Aged Coode Island Silt (CIS) and the older Quaternary Fishermens Bend Silt (FBS) deposits, in areas where these materials directly overly the aquifers. As a large portion of the urban area of South Melbourne and the old river course of the Yarra River contain extensive CIS deposits, and were within the drawdown influence of the tunnels, the management of the hydrogeological regime was very important. The permanent design of the tunnels comprised drained and undrained sections (a partially tanked design) which, along with some permanent recharge, provide long-term protection against the possibility of accelerated settlement rates. During construction TOJV implemented a comprehensive groundwater management plan to deal with issues related to the temporary drawdown of the aquifers and the temporary acceleration of settlement. This paper describes the hydrogeological regime, the effects of the tunnelling, the monitoring programs, the extensive temporary recharge system, and the consultation program that TOJV utilised to manage the hydrogeological issues.

Jan 1, 1999

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By M A. Ohsberg, A C. Robertson

Quarrying in Australia accounts for a total annual production of around 200 Mt/a of sand, aggregate and materials used in construction. This material has an annual value of the order of $2 billion and, combined with transport costs of a further $1 billion, the annual value of quarry products are in excess of $3 billion. Currently all of the production of construction materials in Australia is from open cut quarrying or dredging. This paper focuses on the extraction of material by underground mining methods, termed æunderground quarryingÆ. The paper considers a case study for future underground development expansion of the existing open cut Mt Coot-tha quarry, located 5 km from the centre of Brisbane, Queensland.

Jan 1, 1999

By K Baker, J Purtill

One of the key challenges for the mining industry globally is the rehabilitation of mine waste, and Queensland is no exception. Out of pit waste structures including waste rock dumps and tailings storage facilities, create novel landforms which require ongoing maintenance and pose risks to the environment and sometimes to communities. Where multiple mines co-exist, such as parts of Queensland’s Bowen Basin, individual mines can often be constrained by adjoining operations. This presents opportunities for broader rehabilitation strategies to be considered, more than the current single mine focus, that may provide better environmental outcomes for a region. Given recent global disasters involving tailings storage facilities, and our team’s endeavours to drive Queensland to achieve leading practice in mined land rehabilitation, we are exploring the potential to maximise in-pit tailings disposal opportunities for coalmines through shared waste management strategies. A shared waste management strategy is where two (or more) mines, owned by different companies and operated under different environmental permits, transport tailings from one mine to the other in close proximity, for disposal in a disused pit. This would reduce the number of waste structures to be built, operated, rehabilitated, and managed in perpetuity. Our objectives are to identify and remove barriers to tailings transfers between sites to:  minimise environmental risk  minimise long-term liability of managing mining waste and associated structures  support improved outcomes for the local community. To determine the scale of coal waste disposal practices in Queensland, internal data and publicly available imagery was analysed by the Department of Environment and Science in 2022. Approximately 6500 ha of land in Queensland is utilised for coalmine tailings storage facilities or codisposal areas, with ≈ 3700 ha of this being out of pit.

Aug 2, 2023

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Hilden, G Forbes, Z Ye, M Yahyaei, F Reyes, V Jokovic

Soft sensors offer several practical advantages for the process control of comminution circuits by combining multiple conventional sensors and other data sources with real-time analysis using mechanistic, phenomenological or machine learning models. While there has been a growth in the use of machine learning techniques for developing soft sensors in minerals processing applications, this paper describes advantages and challenges of using soft sensor models developed on the basis of process knowledge. Recent experience with three new soft sensor technologies developed by the authors are discussed. The Mill Filling Inference Tool which has been implemented at several mine sites, compares SAG mill load cell and power draw measurements with outputs of a semi-mechanistic power model to estimate the mill ball and total filling in real time. The progressive wear of the mill liners is modelled, allowing the model to correct the load mass due to the mass loss automatically and to estimate the charge trajectory. This information enables the mill to be operated more confidently near its limits. A coarse-ore stockpile soft sensor as been recently developed using a 3D cellular automata-based model to track ore size throughout the pile, and estimating the live capacity and size at each stockpile feeder to the primary mills. Finally, a hydrocyclone soft sensor is being developed to monitor performance using available hydrocyclone models to estimate the size and flow balance around the cyclone in real time. The model-based soft-sensor approach aims to synthesise and analyse existing data and provide operators and engineers with process- and model-relevant information that can facilitate making better process decisions. Maintenance data has proven useful for model development as it allows soft sensors to automatically adjust and compensate for the effect of progressive wear, for example for mill liners, thus helping the models to maintain calibration throughout the equipment life.

Aug 24, 2022

By A Grice

AMC has completed a number of backfill options studies, including several in recent years for large, three-dimensional orebodies involving total extraction by longhole open stoping with backfill. This has led to the development of a thorough review methodology that assists in the selection of the most appropriate backfill system and the most economic mixes to achieve the required performance. A recently developed design tool has simplified the calculation of backfill strengths for various exposure dimensions and automatically determines strengths incrementally over the height of a stope. Using a generic orebody with a plan dimension of 120 m wide by 360 m long, several different stoping layouts have been analysed to determine the effect of stope dimensions and sequencing on backfill strength requirements. This has been done for stope heights from 50 m to 300 m, in 50 m increments. The required strengths have been calculated in slices and summarised for each stope in four equal layers. The average strength requirement for each layout at each stope height has been compared graphically. For all stope heights, a panel stope layout that minimises the proportion of primary stopes results in a lower average strength requirement than grid layouts on a checkerboard pattern. However, for very high stopes, smaller plan dimensions become more economic. The increase in required strength with stope height is non-linear, making taller stopes potentially more attractive. The main cost factor in most backfills is the rate of binder addition, which is closely related to the strength required. By choosing a layout that minimises the backfill strength requirement, significant savings in binder addition rates and overall costs can be achieved. These must, of course, be weighed against other factors to determine the optimum stoping layout and backfill system.

Jan 1, 2000

By A T. Bernardes

Using the cellular automata computational technique it was possible to simulate the generation and discharge of an iron ore pellet pile inside a direct iron reduction oven, as well as to calculate the reduction degree of the pellets as they leave the oven. It allows simulation of the variation of operational parameters and verify the results of those variations in the pellet reduction degree. The simulated data was validated in two instances: for the dynamics of the pellet flow inside the oven it was used in an acrylic bi-dimensional silo; and data from direct reduction iron literature was used for validation of the pellet reduction. The simulated results were considered acceptable to describe the movement of the iron pellet inside the direct reduction iron oven and to describe the iron pellet reduction direct in the oven.

Sep 26, 2011