Search Documents

An effective production control system should maximise recovery of economic material from the resource. To do this, internal waste must be accurately delineated and efficiently removed. Achieving this is most difficult in low grade blocks just above and just below the cut off grade, where ore:waste separation follows assay or statistical, rather than geological boundaries. Difficulties arise from sampling errors, configuration of the economic mineralisation, and local variations in geology. Mine bench parameters and mining equipment size apply further constraints to the actual field separation of the ore from the waste. At BCL, management of the resource starts with an effective orebody model for planning, scheduling and ore:waste prediction. Ore production from each mining location is reconciled with concentrator tonnage and grade, and the reconciled grades are compared with the planning orebody model to highlight any Differences.

Jan 1, 1986

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

A form of wet pelletization is described where the bridging of the individual particles is achieved by a second liquid phase that pref- erentially wets the suspended solid particles. The phenomenon can be used to obtain efficient separation of solids from carrier liquids, to form spheres from finely divided solid materials, and to separate selected constituents from a body of mixed solids. Typical examples of each of these applications are presented.

Jan 1, 1974

By M R. Asef

Although generation of environmentally harmful hydrogen sulfide is considered to be related to sour gas fields, sweet gas reservoirs and waste fluids, travertine springs and geothermal fields may also produce acid gas (H2S and CO2) under certain conditions. The potential parameters influencing such a possibility need to be fully investigated to evaluate the extent of the consequences and predict hydrogen sulfide generation accordingly. Reports on hydrogen sulfide production at different regions and fields were gathered worldwide for the cases when some of them did not have such a problem previously. In order to inspect different aspects of these case studies, some other regions with no hydrogen sulfide content were selected as control. In all cases water samples were taken carefully for chemical analysis in the laboratory. Besides, mineral compositions were characterised in some cases for better evaluation. In order to give a thorough prospect of hydrogen sulfide production, a geochemical model was prepared. In situ engineering geological conditions, especially pressure and temperature, were assigned in the model to investigate the possibility of H2S generation using PHREEQC software. The results of modelling revealed that although many similarities existed between mineral compositions of the cases, certain formations were particularly prone to hydrogen sulfide generation. For better evaluation, important exchangeable cation ratios such as potassium/sodium, calcium/magnesium and ion proportions like sulfate and chloride were calculated as trends of the formations. As expected, the model could successfully monitor a higher ratio of SO42- and Cl- in potential H2S generator formations. Wide variation in percentage of HCO3- was considered as a secondary observatory parameter for better estimation. In addition, it was noticed that higher anion content created an environment ready to absorb any cations and this makes H2S generation easier. Finally, using correlations between predictors and estimators for low depth and deep samples defined the degree of effectiveness for every sample.

Sep 26, 2011

By M McGeough

Following the success of calcrete sampling at Challenger, calcrete sampling has been widely adopted as the primary exploration technique for gold exploration, in the Gawler Craton. Calcrete is uniformly distributed over large areas and produces discrete gold anomalies. This allows drilling to focus on specific gold anomalous targets. However, despite widespread use of calcrete sampling, very little is known of the origin of calcrete in the Gawler Craton, and the link between calcrete gold anomalies and primary mineralisation. In an attempt to understand this association Lisa Gibbons recently completed an honours project at the Old Well Prospect approximately 45 km SSE of Tarcoola. Her work is part of a collaboration between CRCLEME, MESA and MIM Exploration. At Old Well, a calcrete anomaly (>10 ppb Au)covers an area approximately 7 km x 2 km with a peak value of 97 ppb Au. The study looked at the regolith as a whole, processes of its formation and nature of mineralisation within it. She was able to combine previous calcrete and drilling results with her own observations. The results from this study highlighted problems in relating surface calcrete anomalies to in situ gold mineralisation.

Jan 1, 1998

Zinc alloy castings continue to account for a very large, world-wide end-use market for zinc. However, an ever expanding multitude of other materials and processes are increasingly providing viable, cost-effective alternatives to designers, many of whom have no particular allegiance to any one industry. In order to meet this challenge, innovation of and for the zinc hot chamber pressure die casting process, in concert with sustained and inventive market development, is clearly required. While 'Quality' is now the watchword, and the goal of zero defects is being rigorously pursued, other important goals which must be addressed include net shape casting, enhanced productivity and increased energy efficiency. The paper gives an overview of several practical, process-orientated, projects designed to help achieve these goals. For example, a project designed to understand and precisely measure dimensional changes of castings with time has provided some of the critical information needed for net shape casting. A second study is looking anew at surface quality in relation to process conditions as an important step toward the goals of zero scrap rate and increased productivity. Developing the correct die casting machine parameters for achieving optimal quality and properties of zinc (ZA) die castings is a further example of research designed to benefit both the die caster and his customer, chiefly the original equipment manufacturer (OEM). A project on die soldering or galvanising in response to varying process parameters is similarly being considered in order to foster increased understanding and avoidance of problems, with a special interest in the use of special coatings. The maintenance or expansion of the future market for zinc die casting alloys also depends on design for functional applications, as an adjunct to their traditional decorative use. The role that alloys with enhanced properties can play, such as ZATEC, a new high creep resistant alloy developed specifically for elevated stress/elevated temperature applications, will be briefly discussed.

Jan 1, 1993

Two independent sets of observations from rifted con-tinental margins suggest a way to reach a quantitative under-standing of how the topography of rifted margins erodes. First, a prominent erosional escarpment, which demarcates an elevated, inland region of low relief from rugged, deeply-incised terrain on the seaward side, is the main feature of the geomorphology of many rifted continental margins. Second, apatite fission track ages from the southeast Australian and southwest Saudi Arabian margins scatter about constant Paleozoic ages over the higher elevations inland from the escarpment, but decrease systematically seaward of the escarpment to near-rifting ages approaching the coastlines. We have developed erosion models based on conservation of mass principles to explain these observations. These models seek to explain the "rejuvenation" of erosion at the time of rifting, initiation of the observed erosional escarpment, and its migration inland with time at a rate on the order of 1 km/10 yr. We find from the modeling that erosion at rift flanks and passive margins is fundamentally a non-linear pro-cess. The erosional development of passive margin topogra-phy has much is common with travelling wave solutions to non-linear diffusion-type problems, and to self-similar sto-chastic processes, such as diffusion-limited aggregation. We suggest that the fission track data record the thermal effects of erosional unroofing at rift flanks and passive continental margins. Models intended to explain the erosional develop-ment of continental margins must explain both the geomor-phology and the fission track observations as well.

Jan 1, 1990

By Maiman R

One method of forecasting prices of metals is based on analysis of historic relationships between prices, inventories and consumption. The first, but generally overlooked step in this analysis should be to remove from the inventory and consumption figures the effects of seasonal variations. The next step is to construct diagrams which show prices plotted against ratios of inventories to consumption. These diagrams indicate that, when inventories are high, prices show little response to changes in inventories. Below a critical level of inventories, however, the psychology of the market changes and small changes in inventories lead to large moves in prices. The critical level of inventories is termed the "pinch-point"; the diagram which shows prices in relation to ratios of inventories and consumption may be called a "pinch-point diagram".

Jan 1, 1990

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

By Schofield D, Denby B, Stout F, Moli A

This paper documents the development of a user-friendly computational program, which has been constructed to assist the mine ventilation engineer in the optimal design and operation of methane drainage ranges. In the past, many computer tools for ventilation engineers led to the development of `research systems'. These computer systems, although developed with the needs of the industry in mind were due to a combination of inexperienced programming methods and the availability of suitable user interface software not easily accessible to the practising engineer. Recent developments in computer hardware and software (particularly windows based graphical user interfaces) mean that engineers no longer need to dedicate large amounts of valuable time to become familiar with often complex items of software. The authors of this paper intend to demonstrate a practical system which successfully integrates complex mathematical models, an easy to use interface and knowledge based techniques. The graphical interface guides the user to draw on the screen a mimic diagram representation of the methane drainage network. The user is prompted, during the construction of the drawing, to input the information and data required by the calculation and knowledge based procedures. The computer program then calculates all of the flows, purities and pressures throughout the network. Given reliable measured data from an existing range a comparative analysis can be performed between the predicted and measured network flow data. A knowledge-based system may utilise this analysis to either update the operational status of the network or suggest either a reasoned maintenance or remedial strategy to improve the performance of the drainage system. The development of the OMEN project has been carried out at the request of the Midlands Group, British Coal Corporation, Edwinstowe. The system is about to be field tested at a number of mines. It is hoped that when this paper is presented that the system will be used at both Group and mine level.

Jan 1, 1995

This paper is written as a supplement to that of Edwards, Baker and Knight on "The Geology of the Wonthaggi Coalfield" 1, the West Area pit being in an early developmental stage at the time of their paper. The thin seams to the west of Dudley Basin 2 had beenknown for many years but it was not until 1935 that it became necessary to work them. The West Area Pit came into production as Dudley Area Pit approached exhaustion in 1937. From available information it was estimated that early work would be in a 36in. bottom seam. The present top seam was not included in the reserves, but it was to be extracted where it proved thick enough for economical working.THE SEAMSEdwards, Baker and :Knight (1944) had insufficient information to correlate positively the West Area seams with those in the Dudley Basin. Their opinion was, however, that they were a westerly extension of the Bottom Seam. Since then the driving of the present north-east heading towards No. 4 Bench McBride Tunnel has established that the West Area seams are those worked as Bottom Seam in the Dudley Basin. West Area Top Seam is a seam that occurred above the Bottom Seam in the Dudley Basin. Only sporadic attempts have been made to work it in Central Area, because 30in. was considered an economic minimum height until recent times. This seam should not be confused with Top Seam, Dudley Basin, which lies some 300ft. above the bottom seam measures and except in isolated areas over deeper workings has been eroded away in West Area.

Jan 1, 1953

Jarrah Decline is currently the only underground operation at the Boddington Gold Mine, (BGM). The mine is located 120 km SE from Perth in WA, with mineralisation hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt (Morley and McBride,1995). Open cut operations commenced in April 1987 with a mill throughout of 3.OMtpa. A number of upgrades have since taken place, with the oxide material throughput currently milled at a rate of 7Mtpa. In 1992 a separate circuit, the supergene mill, was commissioned to treat copper material from the open cut and now ore from the Jarrah Decline. Current throughput in the supergene plant is 30,000 tonne per month, with a varied blend according to mill requirements. Total gold production from the Jarrah Decline in 1994 was 60,000 ounces from 90,000 tonne of ore.

Jan 1, 1990

Standards in the public reporting of resources and reserves in Australia have dramatically improved since the implementation of the Australasian Code for Reporting of Mineral Resources and Ore Reserves (The JORC Code) in 1989. Whilst the JORC Code states clearly that Mineral Resources and Ore Reserves are imprecise calculations and should be treated as estimates, there is strong evidence that many people regard them as fact, including some accountants, directors, auditors and investors. Mineral Resources and Ore Reserves are key inputs in the valuation of a mining company and the determination of financial performance. Geological knowledge is the foundation upon which Mineral Resources, Ore Reserves and investment decisions are made, however this information carries with it substantial uncertainty. Case studies and company reports have established that errors derived from inadequate geological inputs have led to reduced profitability in operating mines and in extreme cases the premature closure of mine operations. Whilst there are many causes of mine closure and reduced profitability, including commodity prices and exchange rates, the cumulative effect of all geological uncertainty contributes significantly to the erosion of the credibility of mining within the investment community. There are a number of methods used to characterise and model uncertainty in Mineral Resource and Ore Reserve estimation. Empirical mining indexes, sensitivity analyses, Monte Carlo simulations and Conditional simulations are used to identify and estimate geological uncertainty, notably the quantification of uncertainty in grade and tonnage estimates. These techniques have not generally been applied to estimating geological uncertainty associated with key Ore Reserve inputs such as appropriate mining technique, equipment selection, production rate, mining dilution, stability requirements, materials handling, metallurgical processing, product quality and waste storage. New software tools are needed to model the entire mining process with all its geological and other interdependencies, enabling all uncertainties to be separately identified and estimated. By its very nature, mining involves the assumption of significant technical, financial, political, environmental and social risk. Success comes by understanding and managing these risks and consequently the mining industry will never choose to reduce the level of geological uncertainty to nil. The ultimate aim of improved identification and estimation of geological uncertainty is to quantify inputs into the Ore Reserve process, allowing a company to assess the risks and manage these accordingly. This approach is relevant to feasibility studies for new projects as well as life-of-mine planning through to the weekly schedule at existing mines.

Jan 1, 2003

By M Battersby, F Parra, S Sanchez-Pino

Pneumatic flotation, as developed by Dr Rainer Imhof, has been applied in commercial beneficiation operations since 1987. Over 85 flotation cells have been installed in more than 30 operations, successfully beneficiating a wide range of minerals. Pneumatic flotation is however still considered as a non-conventional flotation process. Due to its highly selective nature in operation it has generally found its market in difficult applications where conventional flotation equipment has struggled. Compa±fa Minera Huasco (CMH) operates an iron ore pellet plant in central Chile. CMH desired to produce a low silica pellet for the export market where the SiO2 grade should not exceed 1.5 per cent. It is common practice in other countries to float quartz from hematite with relative ease. However, the silicates contained in the magnetite ore of CMH are only present as quartz in small quantities and the major undesirable silicates are difficult to float. CMH spent considerable time on developing a reverse flotation process and a reagent suite to try and reduce the silica content to acceptable levels. However, extensive laboratory and pilot plant tests with conventional mechanical tank type cells and with column cells failed to produce the required reduction in impurities. A series of tests with pneumatic flotation cells indicated that this type of flotation technology could achieve the required silica target. A 500 tph Imhoflot pneumatic flotation plant was subsequently constructed and successfully commissioned by CMH, making it one of the largest iron ore flotation plants in the world. This paper details the background and testing that was undertaken by CMH which led them to choose pneumatic flotation as the preferred process and compares the test results with that achieved in the industrial plant.

Jan 1, 2005

By Wilson R. G

Mining conditions imposed by a coal seam roof can be analysed according to natural causes, before consideration of strata control. All types of roof behaviour can be explained by considering only three independent variables. They are roof rock types, rock stresses and discontinuities. Roof rock types encountered in the Sc.ithern Coalfield of New South Wales (NSW) are sandstone, shale, mudstone, laminite and coal. Each rock has its own mode of failure. Lithological stability of the sediments varies from one type to another. Regional stresses upon a coal seam roof will vary in magnitude according to the proportion of gravitational stress, which is related to depth of cover, and residual stress, which is related to the maximum depth of burial and may be gauged by coal rank. Local stresses will vary according to tectonic deformation, related to irregularities in seam structure.

Jan 1, 1976

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993

By Chenggang W, Junhua D

Fragmentation variation laws in loading and non-loading areas are obtained by cement block model blasting experiments under various stemming lengths. A reasonable ratio between loading length and stemming length is worked out according to minimum average fragment size. The present continuous loading structure, for its very long length to be stemmed, leads to insufficient fragmentation in the upper part of bench. So a new loading structure with bottom air cushion is put forward. The author analyzes blasting effects and processes of two loading structures' and proves that there exists a optimal length of air cushion.\

Jan 1, 1990

By A G. Grice

Surface disposal of mining processing wastes is usually perceived as an undesirable consequence of meeting societyÆs needs for metals and minerals. Environmental disasters associated with the discharge or storage of such wastes, though infrequent, can have very damaging consequences for the environment and the industry. Reducing or eliminating the potential for such events may be achieved by placing some or all of these processing wastes back into the voids created by the mining operations. Processing operations may limit or enhance the opportunities for using tailings and other waste products as a backfill material. Backfilling is a truly multi-disciplinary process and requires the informed involvement of mining, metallurgical, engineering and environmental specialists. This paper describes the range of fill types currently being used in Australian mines, particularly those utilising processing wastes as constituents. It focuses on how processing operations can affect the suitability of these materials for the various types of fill, the resulting fill properties, fill performance and costs.

Jan 1, 2002

By Hagan T. O

The problem of rockbursts presents a serious threat to many deep, hard-rock mines. For several decades, the owners and managers of affected mines have been concious of the urgent need to control rockbursts but, to a large extent, their efforts have been hampered by a lack of fundamental knowledge. This paper will attempt to outline the extent and depth of present understanding of the phenomenon and to show how better control may be achieved in the future. It is suggested that it is helpful to distinguish two aspects of the problem: that pertaining to the mechanism of the seismic event and that associated with the mechanism of damage. Understanding damage mechanism will enable development of better support techniques while proper understanding of the source mechanism could lead to better mine planning and improved stoping layouts. In this regard, the practice of partial extraction with systematic strike stabilising pillars is discussed in some detail.

Jan 1, 1986

By Scales PJ

Fatigue is the primary cause of failure of structural and mechanical components subject to dynamic loading. Recognition of this basic fact and the development of appropriate techniques and details are important in the design and repair of off highway trucks (OHTs). The frames and appendages of OHTs and other mobile plant used in the Pilbara are subject to tough operating conditions. Any fatigue-prone details quickly show up and become a maintenance liability of considerable concern. Much of this equipment is approaching the limit of its fatigue life and maintenance managers face decisions on whether to repair or replace. Even new equipment often contains some poor details which suffer distress soon after commissioning. In those cases a repair is required which will reinstate the detail to its original intended design life. Repair details must be practical and cost effective. They must also be tailored to the capability and expertise available in the field or in local manufacturers' establishments. This is particularly important where original equipment was manufactured overseas and long delivery times are involved. Lessons are drawn from components which have failed, using the evidence constructively, to provide an upgraded part or an improved substitute. With the experience now available it is relatively easy to extrapolate to cover new problem areas. This paper describes specialised techniques of mechanical fastening and detailing for low fatigue susceptibility, built up over many years of experience with OHTs and other mining plant and equipment in the Pilbara.

Jan 1, 1982