Search Documents

By Lynch AJ, Musgrove NH

The behaviour of chalcopyrite and pyrite in the rougher-scavenger and regrind-retreatment circuits in the Warrego concentrator is discussed. The effects of change in xanthate addition on the separation of chalcopyrite and pyrite is described. The effect of the regrind mill on the (flotation rate of particles containing chalcopyrite and pyrite is discussed with particular reference to the importance of removing sub-mesh particles from the feed to the regrind mill.

Jan 1, 1975

By McGill RA

The Ranger Uranium Mine is surrounded by a World Heritage National Park. The strict environmental controls under which the mine operates are based on scientific and social requirements. Release of non-process storm runoff water to the Magela Creek during flood discharge and under controlled conditions has been identified as Best Practicable Technology for the operation of the water management system. Social and political factors have limited this release to a wet season with an Annual Exceedance Probability of one in ten. The first-generation trigger mechanism was based on a percentile analysis of monthly rainfall. The second-generation trigger is based on cumulative monthly volume increase in the retention ponds and is considered to be more applicable to the operation of the mine water management system.

Jan 1, 1988

With the sinking of the new No. 3 Shaft and the increasing depth and northward movement of the mining operations, improved ventilation of the mine workings became necessary and it was decided to sink a new upcast ventilation shaft midway between No. 2 Shaft and No. 3 Shaft.The shaft is finished to 16 ft. internal diameter and connects with the mine workings at the 2,600-ft. level. It is lined with unreinforced Concrete approximately 12 in. thick. The shaft sinking routine was drilling, blasting and mucking by hand using a 27-cub. ft. capacity bucket. The concrete lining was poured in conjunction with the sinking and was normally finished within 30 to 50 ft. of the shaft bottom.

Jan 1, 1957

By Redman P. G, McMahon B. K

A simple technique for evaluating the field stress ratio is presented, based on the results of extensometer or convergence tape measure- ments taken in an advancing tunnel. This tech- nique also yields a value for the rock mass modulus, provided Poisson's Ratio is assumed. The results of two case studies are presented illustrating the effectiveness of the method.

Jan 1, 1981

By Torabi S. R, Daly C. R

Wind blast is the sudden movement of air displaced by the massive collapse of roof rock in underground openings and is experienced as a high velocity flow of air through adjacent workings. The initial flow in the outbye direction is often followed by 'suck back', that is a reverse flow of air towards the newly created void. As part of the Wind Blast Project, undertaken by The University of New South Wales, Department of Mining Engineering, a physical model was constructed. One of the functions of the laboratory wind blast model is to provide insight into the dynamics of the interaction between the falling strata and the air being compressed below. During a collapse, some air is expelled into the surrounding roadways while the remainder penetrates towards the top of the roof elements. In this paper two aspects of the rock mass properties which influence the phenomenon are considered: - Flow paths through the falling roof element, ie the permeability of the roof element; - Bed separation prior to the fall which introduces a void above the roof element. A series of tests was carried out utilising the physical model in order to investigate the relationships between the flow of air through the simulated roadways, the variations in gauge pressure above and below the falling roof element, and the acceleration and terminal velocity of the latter, all as a function of the flow paths through the roof element and of the extent of the void above. The results of comprehensive tests using the wind blast physical model suggested that the time history of outbye air flow in the simulated roadway comprises two distinct phases. a) A primary phase, characterised by a high velocity flow of air which exhibits a peak and corresponds to the period during which the roof element is accelerating. The peak air velocity is related to the acceleration of the roof element. b) A secondary phase, characterised by a residual air flow of a lesser velocity than in the primary phase and corresponding to the period during which the roof element is falling at its terminal velocity. The velocity of the residual air flow is directly proportional to the terminal velocity of the roof element. In a monolithic collapse of a roof element it was shown that the presence of flow paths in the roof element increased the air velocity in the roadway in both the primary and the secondary phases. The presence of an air-filled void above the roof element, on the other hand, influenced the air velocity only in the primary phase by increasing the peak air velocity. The overall duration of the process was however decreased as a result. 'plug type' collapses, where roof failure extends to the ground surface, potentially generate the highest peak air velocities likely to be encountered during wind blasts.

Jan 1, 1995

By P Hayward a, P Evans, K Prince, F Radke

Operating efficiency is becoming paramount as the mining industry moves towards globalisation and conglomeration. Mining companies are continuously searching for new technologies that can improve plant efficiency, by reducing operating costs and maximising metal recovery. Identification of how gold losses occur within an operating plant is crucial for determining appropriate operating strategies for improved metallurgical performance. Classical mineralogical and metallurgical techniques enable the operator to identify where losses occur in terms of particle size and mineral associations, however how the gold is hosted within the mineral grains (for example, as solid solution or as fine micro-inclusions) is more difficult to determine. This paper provides details of the testwork methodology, and resultant laboratory study to improve gold recovery.

Jan 1, 2004

The Mine Safety and Inspection Act, 1994 of Western Australia recognises the importance of ground control in underground mining. The recent safety performance of underground mining is summarised in terms of the most common causes of injury and fatal accidents. A review of current ground control practices is presented and the concepts of local and large-scale ground control are introduced. The need for a more systematic approach to ground control is considered to be directly related to requirement to improve safety performance. The new regulations will require that certain geotechnical issues be addressed during the life of a mine. To comply with the regulations it is suggested that a ground control management plan be developed for each mine. The geotechnical issues associated with the ground control management plan are reviewed and hazard recognition aspects discussed.

Jan 1, 1995

By Cutmore NG

The moisture content of iron ore is important in handling, stockpiling, transport and further processing operations. Typically these ores contain both `free' and `bound' moisture, the latter being moisture that is not removed in a conventional laboratory determination of moisture by air drying at 105¦C, and it is the free moisture that is important in dust control and ore handling. The CSIRO Division of Mineral and Process Engineering has previously developed and commercialised gauges, based on capacitance and microwave techniques, for the on-belt determination of moisture in coal and minerals. However, these gauges determine total moisture, and have a different sensitivity to free and bound moisture in the material analysed. Consequently, the accuracy of determining total or free moisture alone may be significantly affected by variations in the bound moisture content. An investigation has been carried out on the simultaneous determination of free and bound moisture in iron ore fines (

Jan 1, 1993

By Badal R

Rock Discontinuities ("joints") affect blasting results. An investigation was carried out to understand if blast parameter such as spacing needs to be altered with the change in joint direction. Small scale laboratory studies in jointed limestone blocks have been carried out. It is shown that optimum spacing is variable with the "joint" orientations. Evidence is presented from field studies in four limestone quarries supporting laboratory studies. Reasons for success and failure of widespacing technique is also provided. Only with suitable orientations of "joints: widespacing is successful.

Jan 1, 1990

By Tagawa H

In Japan, geological condition do not only vary in a wide range of strata but are also extremely complex with the existence of faults and aquifers. With respect to rocks, in particular, it is very rare that homogeneous rocks are distributed uniformly. In general, geological conditions are distributed in a wide variety, ranging from earth, sand, soft and medium rocks to hard rocks. Under these geological conditions, when planning of the tunnel construction is to be made out, either blasting method or tunnel boring machines must be selected taking into consideration the geological structures along with the designed tunnel route,' possibility of encountering aquifers, hardness of rocks anticipated and also, the adjacent environ- mental conditions. In the process of select- ing an excavation method,, it is important to make a comparative investigation between the above two methods considering the advantages and disadvantages with regard to the respective operating efficiency, economical efficiency and the conditions and scope of application as well. Furthermore, in addition to these considerations, the recent environmental restriction, which does not allow the blasting in the surroundings of residential areas, must also be taken into account. Because of this, in some cases there is no alternative but to use a static excavation method or a tunneling machine even when these are less efficient than blasting.

Jan 1, 1987

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

A relationship is predicted between oxidic nickel in slag, oxygen in matte and Ni/Fe ratio in matte after the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters. Oxidic nickel in slag is found to increase with increase in oxygen content of matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1979

Oxygen is required for the leaching of gold ores in cyanide solutions. The source of this oxygen demand and the effect of dissolved oxygen concentration on the rate of the process are briefly reviewed.A method of measuring the oxygen consumption rate is described and some experimental results reported.Fundamental aeration theory and rating of aerators is summarised to show how this type of experimental work provides the basis for full-scale design of aeration equipment.

Jan 1, 1984

The Northwest Territories (NWT) of Canada has emerged as a major new province for diamond mineralisation in less than three years. This is primarily the product of a diligent search in the form of a scientifically based exploration effort. However other factors, including positive aspects of the business and the legal environment have also been identified as assisting the exploration process. In my view these have increased the likelihood of diamond mining becoming a major new industry for Canada. The supportive role of various government agencies has been important. In addition, the character of many of the joint venture deals that have been done has provided an attractive setting for the capital intensive evaluation and development work that is now required to bring the diamond discoveries into production. Perhaps of equal importance is that with the recognition that is being given to the success of the NWT diamond ventures, Canadian explorers are continuing to attract new risk capital for further exploration. This paper attempts to model and quantify the probability of exploration success translating into successful mine development.

Jan 1, 1994

Gunpowder Copper Limited processes 1,000 tonne/day of Mammoth ore in a conventional flot- ation concentrator. Run of mine ore is prepared for flotation by three stages of crushing and two stages of ball milling. The concentrate, in which the primary copper mineral is chalcocite, is solar dried and exported to Japan. The history of operation is summarised, and plant practice and metallurgical problems are discussed.

Jan 1, 1974

Alluvial gold exploration is aimed at recognizing areas of anomalous gold content as evidenced by the nature of the drainage system, its age, geomorphic history and other features of the geological environment including the provenances. Subsequent studies to quantify the findings are governed by the need for accurate data based upon precise measurements. Computerization allows the use of more complicated mathematical procedures than are feasible manually, thus promoting the development of more advanced technological aids. Data banks provide the means of storing vast quantities of information for instant recall.Sample representivity is a major problem and a clear understanding of both sampling and analytical requirements is essential for dealing with problems arising from variations in sample size and particle size distribution. Field samples must always be large enough to ensure adequate representivity or the sampling has failed in its purpose.

Jan 1, 1984

By Paine GG

The in-situ retorting of shallow oil shale deposits is an attractive alternative to the material handling problems of conventional open pit mining techniques, which involve removing overburden, fragmenting and transporting the shale to a fixed retort, and finally disposing of the hot spent shale.For in-situ retorting to be successful, the oil shale has to be fractured and the fragmented rock expanded into a void, to allow controlled propagation of a flame front through the in-situ retort. The principles of cratering with explosives have been used to develop a process for the in-situ fracturing of a thin oil shale deposit overlain by a formation of porous rock. The overlying porous rock formation is first compressed by explosive charges to create voids in the porous rock. The oil shale is then fragmented and pushed in to the voids with separate explosive charges. This paper discusses methods of creating voids in porous rocks with minimal surface disturbance, and then methods of obtaining the most uniform fragmentation of the shale. The whole process can be completed, in practice, in one blast. The results of an experimental blast are presented, and possible modifications are then discussed.

Jan 1, 1985

By Hammond J. R, Ward T. A

The Tom Price orebody, in the Hamersley Ranges of North West of Western Australia, is mined by Hamersley Iron Pty. Limited. The orebody is a folded sequence of hematite and shale bands capped with goethite, with a con- sequential variable iron content. The overall grade is below that required to yield spec- ification product, necessitating selective mining, 'Zone Plans' based on geological structure have been developed to yield forward information on material types and grades. Short and medium term mine plans - the initial stage of quality control - are based upon these 'zone plans'. Blasts are laid out to break to the grade boundaries, thus minimising dilution, and the samples taken from the blasthole cuttings provide blast grades. Blending of shovel out- put from different blasts forms the operational basis of grade control. Shales, being more friable than hematite, produce fines that are lower in iron grade than lump. Quality control in the mine centres around maintaining the target fines grade, compensation being applied in the mine if the fines grade lies outside the target range.

Jan 1, 1973

Blasting, particularly bench blasting, uses finite length cylinders of explosive close to two free faces. The rock to be blasted is usually intersected by a complex 3-D system of joints. To fully simulate a blast, a 3-D dynamic model is required. It is shown that the static stress distribution around a long cylinder can be reproduced by superposing the static stress distribution of a suitable chain of spheres. Thus, the dynamic results for individual spheres given by Favreau (1969) can now be substituted for the static results to give a dynamic model of the stress distribution around a long cylinder. Comparison of measured and computed waveforms show that the measured waveforms are much more attenuated and dispersed than expected. The consequences for explosive evaluation and design are Discussed.

Jan 1, 1990

Our ultimate resources come from the Sun and the Earth System. At this time we face a world crisis in energy, water and soil resources. Global pollution problems are increasing in almost all nations. There is an urgent need to use our vast knowledge with a new wisdom and this requires new integrated teams of experts to provide the best alternatives for the needed new development problems. These teams must include economists, engineers and a broad spectrum of scientists. Today it is possible to produce clean energy, stop soil erosion, clean water and reduce and use wastes of many types.

Jan 1, 1995