Search Documents

By Jarvis ST

Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpasle are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising mulling a 6600 nt' section of an abandoned mine was conducted prior to the mulling of the Littleton Street Mine which had a volume of about 500 000 m'. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully rued for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over I I mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By J Poniewierski, Varcos D

Efficient blasting requires constant vigilance with respect to the actual layout being used in the field. Objective measurement techniques are required in laying out a pattern as the 'by eye' or 'thumb suck' methods cannot guarantee consistent results in layout. Erratic blast results are the consequence of such an approach. In a case study at Sons of Gwalia mine, it was demonstrated that incorrect front burdens had a snowballing effect on otherwise carefully laid out blasts, resulting in both excessive amounts of boulders caused by preconditioning of bench fronts and tops, and tight digging. Both problems caused lower excavator productivity and excessive excavator damage, as well as making it difficult to set out subsequent blasts correctly. Several field measurement methods are available to aid in determining correct blast layouts and one is described in this paper.

Jan 1, 1994

By T Laing, M A. Abdalla, P Hagan

Open pit operators are facing a number of challenges in the area of blasting and blasting processes, such as wall control, quality of fragmentation, explosives consumption and vibration. Remaining financially viable is one of the most significant objectives for mining professionals as they work through the blasting challenges within the mining chain of processes. This objective is such a significant challenge, primarily due to the high consumption of materials and the direct consequences on the downstream processes in the mining work flow, including loading, hauling, crushing, milling and mineral concentration. This paper reviews and discusses a technique to achieve this objective, namely air-decking. The performance in a number of mines around the world is reviewed focusing on the economic contributions of air-deck blasting. Various scenarios are investigated and simulated, covering both conventional and air-deck blasting, using JKSimblast software. The scenarios explore a range of issues and found that optimum results could be achieved with a minimum amount of explosives. The results obtained from the simulations were verified with blasts at Rixs Creek Coal Mine, Australia. Based on the verification results the simulations were then modified to more accurately model the actual conditions and parameters on site and to ensure that the models derived meet the production and control requirements at the mine site. Ultimately, overall analysis and comparisons were applied to the outcomes of the conventional and air-decking blasts revealing a reduction in material consumption of around 25 per cent with consequential savings and up to a 30 per cent reduction in ground vibration.CITATION:Abdalla, M A, Laing, T and Hagan, P, 2012. The contribution of air-deck blasting to open pit mining economics, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 7-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By D Newton

The Mt Morgan Minesite in Central Queensland has been subject to both underground and surface gold mining operations since the late-1800s. The site is largely unrehabilitated and poor quality surface run-off and subsurface leachate is contaminating the nearby Dee River. The site is dominated by a large open cut, which now stores contaminated surface and subsurface run-off. Three models were used to simulate the complex hydrologic processes occurring at the Mt Morgan Mine: a rainfall-run-off model, a groundwater model and a storage behavioural model. Study results showed that the open cut is filling with water and will soon spill large volumes of highly polluted water to the Dee River on a regular basis if no remedial action is taken. This will result in a three-fold increase in pollutant load to the Dee River. Based on a consideration of water quality and quantity it was concluded that the first priority for future minesite water management should be the prevention of spills from the open cut. Potential management options to achieve this objective included surface rehabilitation, catchment diversions, modification of the pump-back system and controlled releases to the Dee River during floods. However, assessing the relative effectiveness of these measures required a thorough understanding of the complex surface and subsurface hydrology of the site. The results of a 100 year simulation of hydrologic processes revealed that previously favoured management options would be ineffective in preventing spills to the river. On this basis, a continuous treat and release strategy was proposed as the only reliable method of preventing future spills. The results of this study demonstrate that good environmental management decisions must be based on an understanding of the relevant physical processes and consideration of cumulative effects over an appropriate time scale.

Jan 1, 2003

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By M Grigorescu, J H. Hodgkinson, M Khanal

The mining industry often needs to operate in remote or climatically harsh locations. The industry has recently been forced to deal with extreme conditions including floods, heatwaves and droughts. As these are becoming progressively frequent occurrences, mines typically build ‘downtime’ into production schedules and expect to incur costs to manage the various risks arising from climate extremes. Importantly, many environmental conditions are becoming more extreme and consequently, risk management based on past data can become increasingly ineffective. Market and shareholder demand for fewer interruptions are another pressure on mines to avoid prolonged or frequent downtime. Hence, adaptation to climate is becoming an important strategic move for many companies, many of whom are using future climate scenarios and alternative risk evaluations.We present here a method that uses commonly available mine site data to assist decision-making for reducing vulnerability to sudden flood. The method, ‘climate-related adaptation from terrain evaluation results’ (CRATER), identifies a mine’s flood ‘hot-spots’ and presents them as a ‘traffic lights’ warning map. The process then requires a failure analysis process such as fault-tree analysis to identify both the cause of possible failures and a range of possible failure-avoidance adaptations. In the final stage, management can assess the most suitable option for the mine, based on the availability of capital such as time, facilities, labour and money in addition to social acceptability of the options. CRATER has been tested in an open cut mine environment and is now being further developed to identify how subsidence over underground mines may impact on flooding and ponding over the mining life cycle (CRATER II). Further work is continuing to test larger and more complex mine landscapes to deliver a method to extract more knowledge from existing data.CITATION:Hodgkinson, J H, Grigorescu, M and Khanal, M, 2016. Reducing mine site extreme rainfall vulnerability using climate-related adaptation from terrain evaluation results, in Proceedings International Mine Management Conference, pp 187-200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

The purpose of this paper is to look at the costs of tailings disposal, and in particular the comparative costs of different disposal methods in different situations. Costs are often the hidden design parameter. We know that they are important but sometimes feel that it is not very respectable to talk about them in public. It is better from a public relations point of view for it to appear that the decision-making process is driven by environmental factors or best practice rather than looking for the cheapest option. But this presumes that the two are mutually exclusive and this need not be so. These issues are discussed later in the paper. It is also commonplace for the scale of the mining operation to change with time, typically involving increased throughput rates and total tonnage. New ideas in tailings disposal make their appearance. The regulatory attitude can change. Having made a decision about the disposal method at the time of original feasibility study and design it is easy to suppose that the mine is æstuck with itÆ. But that also need not necessarily be so. Careful costing of options may reveal that a switch in method could be cheaper in the long run. The designer will often tend to think in terms of initial earthworks and site development costs. Aspects of power consumption, labour, and periodic campaigns to move tailings pipelines and carry out embankment raises are either overlooked or not given the same emphasis. This can distort the evaluation process. It is productive to think in terms of dollars or cents per tonne as a basis of comparison, not just the total sums. Tailings disposal can cost from as little as 10 - 20 ó/t to over $1.00/t which is a big range. There may be good and unavoidable reasons for the high figure but there would need to be to justify being so far over the industry average. At the same time, mining and processing costs, at least for gold, are around $15 - 20/t. Viewed from this perspective tailings disposal will always be a relatively small component of the annual budget.

Jan 1, 2000

By F D. I Hodgson

Twenty-seven observation test pits were excavated at four different spoils dumps at three collieries in the Witbank Coalfield. The holes were dug into the upper three metres of the spoils to ascertain if any weathering profiles, variation with age or influence of topsoil covering could be gauged. Samples from these holes were also subjected to laboratory testing (ABA, humidity cells and mineralogy on several selected samples). The test pits showed that there was a good correlation between in situ paste pH-values and ABA results for samples taken from the pits. At all the collieries, no correlation between age of spoils and in situ acidity could conclusively be drawn. The depth of soil cover also appears to be a minor consideration in determining the eventual acidity of the spoil. In the pits where acidity was found, the weathering was evident when contrasted to areas still buffered. It is unclear if the weathering leads to the acidity or vice versa, as the soil covering appeared to be similar. The spoils proved to be extremely variable with regard to particle size and material on a micro and macro scale. Evidence from most of the holes suggested that there was enough water contained in the fine material in the spoils to support the initiation of acid generation. Conclusions from this investigation are that the mineralogy of the spoils is the most important factor in determining the eventual occurrence of acidic hotspots, and that prior characterisation and selective handling will provide the best management practice for these spoils.

Jan 1, 2003

By D Craw, P V. Angus

Gold mineralisation at Macraes occurs as late quartz-carbonate veins within a body of sheared and hydrothermally altered Otago Schist, the Intrashear Schist. The alteration is characterised by the presence of rutile and the absence of epidote and titanite, indicative of an alteration fluid containing >10 mol per cent CO2. In areas of high strain, a fabric of black microshears develops, gradational to mylonitic cataclasite in the high strain zone adjacent to the hanging wall of the duplex shear zone. The microshears contain hydrothermal graphite, inferred to have been deposited from a methane-rich fluid. The mylonitic cataclasite is characterised by abundant pyrite, the absence of albite and extreme grain size reduction. Gold recovery in the CIL processing plant at Macraes can drop to 50 per cent or lower for some unfavourable ore types. Preg-robbing by a component in the ore, possibly graphite, was suspected as the cause. Mylonitic cataclasite was identified as the lithology responsible for the poor recoveries, with the capacity to bind about 30 ppm of gold in the leach tanks. A program of detailed geochemistry and quantitative grain-size measurement using Coulter analysis was undertaken to identify specific mineralogical factors associated with preg-robbing. The results indicate that pyrite, graphite, and extreme grain-size reduction are the factors associated with highly preg-robbing ores at Macraes. The evolution of the mylonitic cataclasite is accompanied by strong potassium enrichment, as muscovite, and depletion in sodium as albite is removed. This suggests that a simple powder XRD ratio of the albite to illite peaks would suffice to distinguish the preg-robbing ore for grade-control purposes.

Jan 1, 1999

By J Janus, J Krawczyk

Local accumulation of methane in workings of a longwall is one of the most common causes of mining accidents. This gas has many sources: it may leak from goaf through permeable sealings, or through gaps between roof support sections. This stream is then mixed with ventilation air. In the case of auxiliary ventilation ducts, or free jet fans, we have to consider the propagation of a clean air stream in areas with an air-methane mixture. Therefore, modelling the mixing process of methane with ventilation air is important for determining the hazardous areas and thus to ensure safety. Computational fluid dynamics (CFD), specifically the finite volume method, provides tools for such modelling. However, this method requires validation. For this purpose, we have compared measurements with simulations for selected test cases having sufficient similarity to the present problems. In typical methane explosion hazard areas, such as a longwall, it is difficult to make measurements sufficiently to confirm credibility of 3D CFD simulations. As a relevant alternative, an injector methane drainage station placed in an underground gallery has been selected. The stream of drained goaf methane is entrained by compressed air powered injectors and then mixed with ventilation air. Research in this area does not interfere with mining operations, it can be performed safely in a repeatable way. Flow within the site has many similarities to conditions in mine drifts of the longwall area. Comparative research of measuring the methane concentration distribution in the mine drift downstream injector station, with simulations of propagation of the methane stream, was carried out. For measuring the methane concentration distribution in the mine drift a multipoint measurement velocity system developed at the Strata Mechanics Research Institute was used. For the simulation a finite volume method for turbulent flow of gas mixtures was applied. Preliminary results of comparison are shown as graphs and tables.CITATION:Janus, J and Krawczyk, J, 2013. An analysis of the mixing of air and methane in the stream produced by the mine injector station - Presenting preliminary results of measurements and modelling, in Proceedings The Australian Mine Ventilation Conference , pp 49-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By B Maybee, L Fava, D Millar

In the context of a case study for an underground gold mine, the value generated by a schedule optimisation tool (SOT) is assessed. SOT is a software tool for underground mine planning that maximises the net present value (NPV) of a development and production schedule. A baseline study measures the NPV of a schedule generated by SOT from a sequence prepared by the site mine planners. Operational resource constraints and precedence constraints are adhered to by the schedule and NPV is evaluated with a financial model including revenues, costs and discount rate, as specified by the mine planner.The case study has several facets in addition to the baselining component. Scenarios were conducted that examined the degree of constraint on operational resources, the projected gold price and unit costs. Life-of-mine schedules subject to optimisation using SOT allowed for equitable comparisons.Haulage was identified as a dominant constraint for the mine. It was one of six operational resources that were used to constrain the optimisation of the mine schedule, with alternative levels for some of these constraints being identified so that their effects on the NPV could be studied. Alternative price projections for gold and different cost projections were identified and their effects on the optimised schedule examined. Price and cost scenarios that brought additional economic material into the schedule at various times in the mine life were considered in comparison to a scenario that assumed no additional economic material would become available.This case study illustrated that the use of a schedule optimisation tool to optimise mine schedules provides mine planners with an ability to perform a wide variety of analyses in a relatively short period of time. Such tools thereby support strategic decision-making that can add significant value to an orebody.The case study demonstrates that by fixing the set of development and production activities to be carried out before optimising the life-of-mine schedule, the mine planners can inadvertently set up a situation where the NPV would be progressively eroded in the last several years of the mine life. This clearly illustrates the need for schedule optimisation to be integrated with life-of-mine planning.CITATION:Fava, L, Maybee, B and Millar, D, 2012. Decision support for an underground gold mining operation - A case study using the schedule optimisation tool, in Proceedings Project Evaluation 2012 , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By G B. Smith, G M. Marshall, A Querzoli

The South Australian mining regulatory framework has adopted a performance based approach to the management of risk. This approach has been in place in South Australia for more than 10 years and is increasingly being implemented in mining jurisdictions in Australia and around the world. Performance based regulation focuses on setting appropriate environmental outcomes to be achieved based on an assessment of the potential impacts associated with the development, operation and closure of mining projects. Measurable compliance criteria, including completion criteria, are set to demonstrate achievement of the outcomes. It is the responsibility of the proponent to propose designs and strategies that will achieve the regulated environmental outcomes and to demonstrate the implementation of their designs and strategies will achieve the outcomes into the future. Tailings Storage Facilities (TSFs) are significant elements of many major mines and each is unique with site specific factors such a materials to be stored, design, size, location, climate, sensitive receptors, operating history of the facility (i.e. changes to design), site culture and company capability amongst a range of other factors. Consequently a fit-for purpose approach is a key principle of best practice regulation of tailings management as it takes the site specific factors into account in setting appropriate outcomes for mitigating the identified impacts associated with a proposed development. Achievement of those outcomes through fit-for purpose, well designed management strategies would ensure safe, stable and economic storage of tailings in a manner that complies with all legislative requirements and presents negligible public health and safety risks. Tailings storage must also have acceptably low social and environmental impacts, both on and off site, during operation and indefinitely post closure. Achievement of environmental outcomes during operations and at mine completion can then be demonstrated to the regulator and community through public reporting of compliance with measurement criteria which establish the appropriate level of impact for each individual operation. A number of new mining proposals including tailings storage facilities (TSF) have recently been assessed and approved in South Australia. The location, size, design, sensitive receptors, public interest and therefore risk profiles of these TSF’s have varied substantially between these new mining proposals. These considerations were reflected in the assessment of the TSFs and the resulting mining lease conditions of approval including the environmental outcomes to be achieved over the life of the facilities. This paper and the accompanying presentation will provide case studies of recently approved TSFs within South Australia and the regulatory framework for each case.CITATION:Smith, G B, Querzoli, A and Marshall, G M, 2018. Tailings regulation – a South Australian perspective, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 166–177 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Hadjigeorgiou

Narrow vein mining, as most types of mining, faces important geotechnical challenges. The specificity of geotechnical challenges in narrow vein mines stems from the nature of the deposits, which are often inclined, discordant and found within fractured rock or faults or in shear zones within country rock. This complicates the construction of representative geomechanical models and limits the applicability of several engineering design tools. Furthermore, in certain cases, the severity of encountered geotechnical problems is considerably greater in narrow vein than in wider orebodies. This paper provides an overview of geotechnical and other challenges in narrow vein mines with a focus on how these are currently addressed. Of particular concern is the use of manual labour working close to the mining face where there is greater exposure to geomechanical hazards. This review concludes with a particular emphasis on understanding the limitations of commonly used engineering tools and techniques to address geotechnical problems in narrow vein mines.CITATION:Hadjigeorgiou, J, 2012. Geotechnical challenges in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By D Adhikary, M Khanal, B Poulsen, H Guo

During longwall mining, the ability to reliably estimate the height of longwall mining-induced fractures is critically important in order to effectively manage mining-induced water inflows and aquifer interference. The extent of mining-induced subsurface deformation, fracture, surface subsidence and aquifer interference is largely controlled by local lithological conditions, mining methods and mine layouts. Therefore for the purpose of quantifying mining impacts it is imperative to incorporate the local geology and mine plan parameters in a mine scale model. Two different numerical models based on 3D continuum (Finite Element Method) and 2D discrete (Discrete element method) domains, respectively, are developed to incorporate the mine site parameters of a study site in Australia. Both the models are calibrated and validated with measured mine data. The continuum numerical modelling method is used to investigate the change in permeability of the overburden strata due to underground extraction considering the full 3D nature of geology and mine layout. The discrete element modelling method is used to simulate the initiation and propagation of fractures, allowing the caving of overburden strata to be represented in a realistic manner, and the permeability enhancement of the strata overlying the goaf to be calculated from first principles. Permeability enhancement in the discrete element model is a direct function of the fractures induced in the deformation/caving process; fracture location, extent, aperture and connectedness. From the numerical modelling under the simulated condition for the mine studied here, it is predicted that the permeability of the caving zone from the goaf to five times the mining height increases by almost six orders of magnitude. In the fracture zone to approximately ten times the mining height, the change in permeability is predicted to be around two to three orders of magnitude. At the height of more than ten times the mining height the magnitude of permeability increased is predicted to be one to two orders of magnitude. CITATION:Khanal, M, Poulsen, B, Adhikary, D and Guo, H, 2018. Modelling of height of connective fractures during longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 254–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D J. A Van Zyl, J C. Cunning

Technological advances associated with the expanded application of paste technology in underground mine backfilling are now stimulating an interest in the disposal of process tailings as paste in the surface environment. Concurrent with the development of alternative surface tailings disposal practices is the requirement to fully understand the consolidation behaviour of tailings in paste form, and to relate this understanding to the significant body of data and operating experience from decades of study of the performance of hydraulically placed tailings. One effective method for demonstrating the benefits derived from handling and placement of tailings as paste is to review tailings slurry consolidation theory from the perspective of the changes which take place in the material as it makes its transition from a loose slurry to a dense, stable deposit resulting from managed thin-layer deposition. For a typical process tailings, an example is provided which illustrates the effect which mechanical dewatering has in accelerating the consolidation process and thereby providing a range of benefits from the perspective of surface disposal. Increased rates of filling (rise), expanded use of upstream embankment construction methods and elimination of impounded surface solutions are some quantifiable benefits which can be assembled on a site-specific basis to allow for valid comparisons with more traditional approaches to tailings disposal.

Jan 1, 1998

In attempting to vegetate pnob!em sites some basic pn.i,ne%ptes, namely the phys.ica.e and chemi.ca2 pnope/ti;es og the problem mateni.al and the selection oU hu.itab.2e p!antts {cor pnopagati.on, have to be considered. Pnobtem sites such as tai ing dams, mined-out atteas, and areas which have been genehaUy advehse2y a46eeted by mining activities, are not only o~ten located in a divehs.ity o4 climatic regions, but they also usuaUy dL64en substantially in theAjt .int' Lns c phys.ica2 and chem.i cat pnopen t i.es . To estabP.ish vegetation on such sites 6requent2y requites: .%) The ame Lonaton oU adverse {yaetors in onde t to exeate a hoot env.utonment suitable Uon "satis1actony" plant growth. .%i) These.2eationo4 plant species suited to the improved Hoot env.utonment, and eompat%b&e with the e2imate o{y the site, and the ultimate Land use o4 the site. iii) The estabL shment o{y a Laboratory and p-LLot scale testing programme to aeeomptizh the above.

Jan 1, 1976

ILZRO sights are locked securely on the targets of the expanded applications and ever-improving quality in the major market for zinc-coated steel. A wide range of ILZRO-sponsored research projects examine issues of formability, paintability, and corrosion resistance for traditional hot-dip galvanising, electrogalvanising, and ILZRO's own proprietary zinc coating, Galfan. Recent research has focussed on the on the interaction between Galfan and different substrate steels to determine optimum combinations for different applications. ILZRO enjoys an evolving role in providing the connection between research laboratories and marketing divisions through supporting research and services for the Galfan Technical Resource Centreò(GTRC) and the recently formed North American Galfan Development Authority (NAGDA). GTRC has just produced a new problem-solving manual that provides a comprehensive source of hands-on solutions for the many Galfan licensees throughout the world, and should contribute substantially to the reputation of Galfan as a consistently top-quality steel-coating product. Meanwhile, NAGDA is advancing the market with new advertising for Galfan based on superior corrosion-resistant qualities proven through ILZRO-sponsored research. Practical manufacturing issues remain at the forefront of ILZRO priorities, with research emphasis on cutting and welding zinc-coated steel to provide direct assistance towards improved product quality and a more secure market. Moving to the arena of die casting, when the specifier looks to zinc to fill a design need, ILZRO-sponsored research projects provide comprehensive documentation on metallurgical characteristics for every zinc alloy under almost any imaginable application. On-going ILZRO-sponsored research is integrating this wealth of data with sophisticated computer programs that model die-casting designs with ever-increasing accuracy, as other ILZRO projects lay the market groundwork for zinc in applications ranging from vibration damping to electromagnetic shielding.

Jan 1, 1993