Search Documents

By T. D. Yensen, R. K. McGeary

While we have not been primarily interested in the determination of hydrogen in the alloys that we have been dealing with, we arc very glad to cooperate in this symposium on sampling and analysis for hydrogen, as we can never tell when we may find it desirable to perform such analyses. Vacuum-fusion Method Our primary interest has been oxygen and carbon, in the analysis of which we think we have become very proficient. Our oxygen-analyzing apparatus is of the vacuum-fusion type (Fig. I). This employs Dr. Derge's type of graphite cruciblc and slit sleeve, with graphite powder between, for heat insulation (Fig. 2) supported in a clear quartz bulb connected to the Pyrex glass system by means of a carefully made ground joint. The latter is kept cool by means of an air blast from a circular copper tube surrounding the joint. The crucible is heated by high-frequency induction and the 24 one-gram samples successively dropped in from the horizontal tube at the top by means of a magnet. The gases (H², CO, N2) are passed through the CuO catalyst held at 300°C. (converting CO to CO²I, H² to H²O) and the CO² and H2O frozen out in the main liquid air trap, while N2 is evacuated. At the end of the operation, shown by the termocouple vacuum gauge indicating a pressure of 10-4 mm. Hg, the analyzing system is isolated by means of the mercury cutoffs, and the CO² and H2oare determined by transferring first the CO2 and then the HzO to the small trap at the right. This is done by placing liquid air on the small trap, then removing the liquid air from the large trap for one minute, which is sufficient to evaporate the Co2 and transfer it to the small trap. The CO2 is then measured by closing the mercury cutoff at the extreme right, removing the liquid air from the small trap, warming it up to room temperature, adjusting the mercury level to one of the three marks on the glass tube (corresponding to three volumes calibrated so that I mm. Hg of CO² corresponds to 0.001, 0.002 and 0.010 mg., respectively, of oxygen) and finally reading the pressure. Liquid air is now replaced on the large trap, the mercury cutoff at the right opened, transferring the COz back to the large trap. The cutoff to the pumps is then opened, the liquid air removed for one minute, thus evacuating the CO², the pumps again cut off and the H2 O transferred to the small trap as before, except that it is now necessary to warm the large trap with a Bunsen burner in order to evaporate all the H2O. This requires about three minutes, as the inner tube must be heated to at least 100°C. In order to prevent H²O from being adsorbed on the glass walls, the glass tubing beyond the catalyst (i.e., to the right in Figs. I and 3) is kept heated to about 150°C. by means of Nichrome ribbon as shown in Fig. 3. For a I-gram sample the above amounts of oxygen (0.001, 0.002 and 0.010 mg.) 35

Jan 1, 1945

By H. C. Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions.

Jan 8, 1950

By A. H. Smallbone, R. Lathe

Considerable efforts have been expended to apply multiple regression techniques to quantitative determinations in x-ray fluorescence analysis. Multiple regression has been shown to be an effective method for correlating x-ray fluorescence intensities to elemental concentrations. Although many other techniques have been devised to solve the problem of matrix effects in x-ray fluorescence analysis, there are few as efficient in terms of storage requirement or ease of programming for digital computers as the multiple regression method. In the case of ore slurry, it has the additional advantage of allowing a unified approach to the problems of slurry density correction and matrix effect corrections. The data used in the present work were obtained with an on-stream x-ray analyzer capable of analyzing 15 slurry streams for as many as nine elements simultaneously. One of its fixed monochromators was set to accept scattered radiation at a discretely selected wavelength as a means of monitoring the slurry's pulp density. The data were reduced to obtain the correlation equations and a computer program combining slurry density with matrix corrections was written in FORTRAN IV to calculate concentrations.

Jan 8, 1969

By AIME AIME

LAST month we published (p. 440) the first half of the L discussion by O. E. Kiessling of the paper on copper by Mr. Vogelstein that appeared in the same-issue, but lack of space made it necessary to hold the remainder for this number. Mr. Kiessling now asks to have the last " sentence of the part already published revised to the form given in the first sentence which follows, and also asks that the two parts, though necessarily published separately, be read together, as a mistaken impression may be derived from the first Dart unless it is read in connection with the statement of the Bureau of Mines policy respecting secondary metals which is here published. .

Jan 1, 1931

By John W. Cahn, John E. Hilliard

Single crystals of copper and silicon-iron were cold rolled in orientations chosen to produce individually the major components of the poly crystalline deformation texture. The orientation dependence of the recrystallization kinetics was studied relative to the primary recrystallization textures of these specimens. It is not possible to rationalize the poly crystalline re crystallized textures on this basis. The results suggest an important role of the interaction of adjacent crystals during the deformation of aggregates. BRICK and Williamson1 first noted evidence that the recrystallization temperature was different for straight-rolled and cross-rolled copper given comparable reductions. Michalak and Hibbard2 investigated quantitatively the effect of rolling procedure on the kinetics of recrystallization of cold-rolled copper and found that material cold-rolled the same amount by straight-pass, cross-pass, and compression-pass techniques developed different deformation and recrystallization textures, different 1-hr recrystallization temperatures, and different recrystallization kinetics. However, the temperature dependence of the rate of recrystallization was essentially the same for all techniques. Similar results were obtained on iron. Dunn and Koh3 in studying the recrystallization textures of cold-rolled silicon-iron single crystals reported large differences in the annealing temperatures and times required to recrystallize specimens of different orientations cold-rolled the same amount. Liu4 and Liu and Hibbard5 utilized the concept of different recrystallization temperatures for different orientations of cold-rolled crystals to rationalize the difference in recrystallization textures found in various face-centered-cubic metals. Their explanation predicted a significant difference in the recrystallization kinetics of deformed (110) [112] crystals as compared to (358) [352] crystals, and, in fact, Liu4 reported evidence that this difference existed at least qualitatively. Verbraak6 who rolled and recrystallized a series of copper single crystals found that the double (112) [111] rolled orientation is related to recrystallized cube texture formation. The effect of rolling intensity on the relative amount of cube component suggests an important role of recrystallization kinetics. Walter and Hibbard7 while trying to relate the behavior of rolled and recrystallized single crystals of silicon-iron to the behavior of polycrystal-line silicon-iron again noted that differences in recrystallization kinetics were necessary to rationalize their results. The purpose of the present investigation was to obtain quantitative kinetic data on the recrystallization of single crystals of both copper and silicon-iron rolled to initial isolated individual orientations corresponding to those found in the polycrystalline deformation textures. These data might indicate the importance of the deformation orientation, i.e. the range of available nuclei, the deformed matrix orientation into which these nuclei grow, and the orientation dependence of their growth rate during primary recrystallization on this texture. I. COPPER Experimental Procedure—A single crystal of 99.98 pet purity copper, grown by the Bridgman technique, was purchased in the form of a bar 1 1/2

Jan 1, 1962

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

By Lawrence Adler

MINE hoist ropes have hitherto been selected by successive approximation, a process both tedious and inexact. The proposed expression is a readily solved synthesis of existing data and the following standard equation:' [ W + Wr + (W + Wr) -a 9 (W + W)f + b] n=T [1] For convenience, a glossary of all terms appears on page 564. Since rope weight (W,) and bending load (B) are functions of unit rope weight (Wv), which in turn is a function of rope strength (T), W, and B can be expressed in terms of T. W, as a Function of T: A study of the curve in Fig. 1, unit rope weight vs strength, yields Eq. 2: W. = -f- [2] Therefore Wr = WvL = T. [3] iv B as a Function of T: From Fig. 2, unit rope weight vs diameter, Eq. 4 is obtained: W, = 1.6d2 [4] B is related2 to d and D, and d has been expressed in terms of W, by Eq. 4, so the curve B vs W, (Fig. 3) gives Eq. 5: 177,000 177,000 This may readily be checked from the expression3 for a 6x19 rope, i.e., d3 B = 288,000D Since d2 = 0.625 W, and N = substituting d into the above expression gives Ea. 6: 180,000 180,000 B T, which will be used. [6] Into Eq. 1 substitute Eq. 3 and Eq. 6, noting that f=0.02: W + T 1.02+=T. [7]

Jan 1, 1958

By AIME AIME

As already announced, the XCIIId meeting of the Institute will be held at Toronto, beginning July 23, 1907. Hotel Headquarters will be at the King Edward Hotel, in which also the sessions will be held. The Queens, Rossin, Wallen, Iroquois and Palmer are good hotels not far from the King Edward. Members must secure their hotel-accommodations beforehand, by direct correspondence with the hotel they select. For those who neglect this precaution, the Local Committee will doubtless do what it can, but is unable to promise anything. Correspondence concerning this meeting (including notices of intention to attend it) should be addressed hereafter exclusively to Mr. W. G. Miller, Provincial Geologist, Bureau of Mines, Toronto, who is the representative of the Local Committee. The excursion to Cobalt, Lake Tenagami, Sudbury, etc., arranged by that Committee, involves the use of a special Pullman train for meals and lodging. After waiting a reasonable time to hear from members, the Local Committee has made its contract for Pullman cars. According to its latest report, there was still room for additional excursionists. Under this head, application made immediately to Mr. Miller may not be too late. Sessions for the presentation of papers, etc., will be held at the King Edward Hotel on Tuesday afternoon, July 23, and Wednesday morning and afternoon, July 24. The following papers have been accepted: 1. Sonic Reflections on Secrecy in the Arts, by James Douglas, New York, N. Y. .2. The Wilfley Table, by R. H. Richards, Boston, Mass. 3. The Tar-Sands of the Athabaska District, by' Robert Bell, Ottawa, Can. 4. The Occurrence of Nickel in Virginia, by Thomas L. Watson, Blacksburg, Va. 5. Coal-Briquetting in the United States, by E. W. Parker, Washington, D. C.

Jul 1, 1907

By H. H. Stout

In the early fall of 1925, the writer was conducting, in the Ledoux and Co. laboratory, New York, experiments directed toward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various different gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500º to 1600ºF. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode particles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500ºF." Smoot's reaction, after a few moments considera- tion, was, "It looks perfectly all right to me.'' The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after conferring as to ways and means, decided to go ahead with preliminary laboratory experiments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: 1. Since brittle cathodes were often unintentionally produced, it seemed probable that the laws controlling this type of deposition could be ascertained. 2. We had already proved the gas-cleaning feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia University for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrouilded and heated by a resistance coil 01 Nichrome wire. Broken tough cathodes were used. Experimental Procedure The first run took place March 18, 1926. The resistance wire gave out when temperature of 1000ºF. was obtained. Pressure was immediately applied: perceptible ram movement stopped when 39,000 lb. per sq. in. on the copper was reached, with a maxi-

Jan 1, 1941

A. Bement, Chicago,Ill. (communication to the Secretary*):— Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible," notwithstandirig that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combuition-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term " combustible " was an advance to be credited to the engineer rather than to the chemist, because the latter, not having to do with the interpretation of analyses in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash- and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression pure coal, which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Jan 1, 1909

By Stephen Burke

THE oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combus-tion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the condi-tions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 21120 + 702 --> 2FeSO4 + 2H2S04 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to dis-close any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1937

By George S. Rice

GROUND movement and subsidence is an important matter from several points of view and it is regrettable that more papers have not been written on this subject in the past year. Damage may be done to surface buildings or to the higher workings of a mine, and a study of the subject gives valuable in- formation on hanging-wall or roof control. The latter objective is strikingly shown in a recent paper presented by Jack Spaulding on Oct. 21, 1937, before the Institution of Mining and Metallurgy, of Great Britain, entitled "Theory and Practice of Ground Control in the Kolar Gold Field, India." All may not agree with some of his theories that were deduced from studies of the many violent rock bursts at depths of 5000 to 7000 ft., but the data obtained are of great value. His theories of symmetrical ring stresses and symmetrical domes which are pictured as perfect are rather hard to understand as such uniformity is un- likely in view of the irregularities in the formation due to folds and fractures of various kinds. All will agree in principle with this idea of domal effects, which have been observed in many countries, but they are generally irregular.

Jan 1, 1938

By Wing L. Lew

LEAD, silver, and zinc, in quantities of economic importance are found in the Aguilar ore. The lead occurs as galena and the zinc as sphalerite and marmatite. The silver occurrence is more complex. Pyrargyrite and proustite have been identified only occasionally. Galena is silver-bearing and so are the various other sulphides, though to a lesser degree. The principal nonsulphide gangue minerals include calcite, quartz, wollastonite, rhodonite, and various calcium, aluminum, and iron silicates. A typical analysis of, the ore is: Pb, 11.2; Zn, 12.3; Fe, 4.4; Mn, 2.2; Cu, 0.15; S, 11.2; CaO. 7.6; "Insoluble," 50.1 percent; and Ag 263 g per ton. Crushing is done in three stages. The primary crusher at the mine is set to deliver about a 5-in. product. The crushed ore is then transported to the secondary crushing plant by a 3-km cableway where the general practice is to hold the product of the first Symons to about 1 in., and of the second Symons to about 1/2 in. When the ore is soft and rich the product of the first Symons is by-passed directly to the ball-mill bins. Dust control in the secondary crushing plant is effected by enclosing the dust-emanating sources and exhausting the enclosures with a Clarage No. 18 fan driven at 1300 rpm by a 20-hp motor. Use is also made of spray water at one or two critical places. Every effort is made to keep the air free from visible dust. Dust counts taken at the working places show dust concentrations of less than six million particles ner cu ft. The composition

Jan 1, 1947

By Wilbur E. Sanders

AT some period during the operation of metalliferous and other commercially valuable mineral-deposits in connection with their underground mining, when the developments therein have become so extensive that their description is tedious and confusing, some scheme for naming or numbering the various workings and their parts is necessary for convenience of ; reference.. A simple and symmetrical yet expansive system of classification must be devised, one that is capable of being extended to cover all possible exigencies and conditions of future operations within the property. Such a scheme, properly arranged, greatly simplifies communication between the various departments of the mining business, as, for instance, between the administrative and the operating departments of the concern, and is of the greatest assistance to the officers of the mine in enabling them to locate and describe particular points and parts of workings and specific kinds of work. Again, in the proper segregation and differentiation of mine-accounts, when they are carried out with that detail which will furnish ready information concerning the cost of a particular piece of work, or the various items and totals of expense connected with the, development,, operation and repair of each or all of the mine-workings, some such method of designation becomes a necessity. . Moreover, such a plan is admirably adapted to the needs of the mining engineer, who, in connection with his reports upon mining-properties, is sometimes required, in his descriptions of certain blocks of ore, to locate lists of assays of samples taken from many and various places, and to designate workings and parts of workings that are located in different parts of the mine, sometimes at points wide apart.

May 1, 1906

By H. C., Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions. Prior to the war years Inspiration's costs of mining by block-caving methods were comparable to, or even below, the costs of some open-pit operations. By the end of the war these conditions were completely changed. Underground costs had risen steadily for labor and supplies. Difficulty was being experienced in finding competent underground men and underground development was almost hopelessly behind schedule. On the other hand, open-pit costs had been sharply reduced through the development of modern earth-moving machinery and plenty of labor was available for surface work.

Jan 1, 1950

By RICHARD MAIZE

IN this critical period of our history, the coal industry of the nation, faced with many obstacles, performed its work safely during the first ten months of 1943. Thousands of the younger mine workers were inducted into the armed forces of our country and in many instances their jobs have been filled by others without much if any experience and training. This situation alone would seem to be sufficient to interfere with the safe and orderly operation of the industry but the Government's demand for a substantial increase in coal tonnage over that produced in normal times introduced a hazard which always accompanies speed, regardless of the skill of the worker.

Jan 1, 1944

By Blamey Stevens

(San Francisco Meeting, October, 1911.) My previous paper is entitled, The Laws of Igneous Emanation Pressure. The present paper lays no claim to the exactitude and completeness of a law, since it is of a provisional nature and may be disregarded when experiments have established a basis for more exact reasoning. The general physical states in which aqueous emanations may occur are first considered. The possible physical conditions under which the mineral elements may occur in emanations are then discussed, and a classification of deposits, dependent on emanation, is proposed. A system of scientific experimental investigation is outlined, and it is shown that the physical and chemical properties of emanation may be exactly determined thereby. The investigation is urged as feasible and simple, and not necessarily requiring large and costly apparatus. It is the only step necessary to make possible the formulation of a complete set of laws of igneous emanation. Process of Emanation. In a rising column, magma ranges in temperature from 900° to 1,200°C. Exhalation must begin at some fairly great depth. What this depth may be we can only surmise, since no experimental evidence is available. Exhalation, however, continues as the magma flows upward, until at another level the occluded gases have all escaped. This depth is probably upward of 5,000 ft. (See Fig. 1.) All exhalations must come from between these two levels. As the whole emanation is the sum of the exhalations and residues, the residues must come from below the uppermost level. They will be most abundant when coming, from those parts of the intrusion which have solidified below the lower level.

Apr 1, 1912

By R. R. Sayers

SILICOSIS is a term known to almost everyone today. Yet, in spite of a great deal of study, much is still to be learned regarding the disease. Government organizations are still continuing their investigations, begun near Joplin, Mo., 25 years ago. Work is also being done in several universities, as Harvard, Pennsylvania, Rochester, and Toronto, and at least two private organizations, the Air Hygiene Foundation of America, Inc., and the Saranac Laboratories for the Study of Tuberculosis, devote most of their time to this subject. Similar studies have been and are being made in many other countries.

Jan 1, 1939

By WALTER CARROLL

Between cross currents of economic factors and international expediencies the iron and steel industry in 1948 made an outstanding contribution to the general economic picture. Were it not for an unfortunate episode during the month of April involving a temporary shortage of coal, 1948 would have been an all-time record year in output. Exceeded in no previous peacetime year, the production of iron and steel in 1948 totaled some 88,500,000 tons. That it was a worthwhile effort of no small magnitude is evidenced by the fact that in three and one half years following the war, this nation has produced as much steel as in the five years preceding the war. This figure of 88,500,000 tons is 68 per cent greater than that for 1939.

Jan 1, 1949

By F. A., King

THE problem of the proper size and capacity of the open-hearth furnace has been a predominant issue ever since its inception some sixty years ago. The original furnaces, built in 1868 at Landore, England, were only to 3 to 4 tons capacity, and from' this there has been a steadily increasing and almost uniform rate of expansion until furnaces producing 300 tons are in successful operation today. At the end of the first half of this 60-year period, or about the year 1900, 50-ton furnaces we're common. Up to this time the problems of expansion had been largely those relating to suficient capital and the engineering development of larger units. But as 75, 100-ton and larger furnaces were proposed apprehension grew and other questions assumed leading consideration.

Jan 1, 1928