Search Documents

By D. C. Sisti

A technical evaluation of actual performance of the preparation facilities at Beaver Consolidated Coal Co.'s Stinson plant is presented, with special emphasis on sulfur reduction in 1-1/2 x 3/8 in., 3/8 in. x 28 mesh, and 28 mesh x 0 size fractions. Evaluation of the heavy medium section of the plant and the treatment of the 28 mesh x 0 coal is included. Design criteria considered for sizing and selection of equipment required to process 1-3/4 million tpy of raw coal on coals of divergent washability characteristics are summarized.

Jan 1, 1976

By Molly Gleiser, John Chipman

The standard free energy of formation of WC was obtained from determination of the equilibrium WC + CO2 = W + 2CO between 1215° and 1266°K. Its uallie is -8340 * 300 cal Per mole over the above range of temperature. AS a part of a program devoted to measuring the stabilities of the carbides, a study was made of the free energy of formation of tungsten carbide, WC. The homogeneity range of this compound is very small,' and it is generally accepted and is dealt with here as a stoichiometric compound. The heat of formation, ?H°f, of WC has been accurately measured by Huff, Squitieri, and snyder.2 The only attempt, however, to measure the free energy of formation of this compound was made by Schenck, Kurzen, and wesselkock3 who brought tungsten carbides into equilibrium with H2 and CH4. Unfortunately their results are not sufficiently accurate nor consistent enough to permit the calculation of free energies. METHOD Heating mixtures of tungsten and carbon powders in hydrogen for 4 days at 1050°C led to formation of some WC without any trace of W2C. It was deduced, therefore, that at least below this temperature W2C will not be formed during experiments with mixtures of tungsten and WC. This was subsequently shown to be correct. The method chosen was the measurement of the equilibrium of the reaction

Jan 1, 1962

By Victor Formanek, Paul Chataignon, Maurice Rey

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By Maurice Rey, Victor Formanek, Paul Chataignon

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By I. R. Taylor

Union Carbide has recently developed two open- pit vanadium mines in the Wilson Srpings area of central Arkansas about five miles southeast of Hot Springs. The ores from these mines, together with those from a larger vanadium deposit at nearby Magnet Cove, are processed at a new 1600- tpd plant built by the company in the immediate vicinity (Fig. 1). The Wilson Springs vanadium deposits are associated with the Potash Sulfur Springs intrusive, a circular igneous complex which is exposed over an area that is somewhat less than a mile in diameter.1 The complex has a crude ring structure similar to that of the larger Magnet Cove instrusive six miles to the east.2

Jan 4, 1969

By James O. Elton

This paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world's supply of arsenic is recovered as a byproduct in the smelting of other metals. It is seen 'on the market in various forms, the most common being arsenic trioxide, the " white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports. Statistics of Arsenic Trioxide in United States.' Production. Consumption. Price Per Pound. Year. Tons. Tons. Cents. 1907..........1.010 5.471 5 1908,.........1,302 6,098 33/4 1909,.........1,007 4,600 2 7/8 1910,.........1,526 5,428 2 1/2 1911,.........3,081 6,539 2 1912,2........ 2,926 Closed at 4 7/8 Arsenic occurs in combitlation with sulphur and the metals in a large number of minerals. It is present in small amounts in many ores. In the roasting and smelting furnaces many of its compounds break down, liberating arsenic trioxide, which is volatilized and carried by the gases into the flue system, where a part is condensed and settles with the flue dust.

Jan 1, 1914

By F. C. Langenberg, J. Chipman

New data on the distribution of silicon between slag and carbon-saturated iron at 1600oand 1700oC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1700°C for slags containing up to 20 pct Al2O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A1203-SiO2 slags over a range from zero pct A12O3 to saturation with A12O3, or CaO.2A12O3. The upper limit of SiO, is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently, 4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/A12O3 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al2O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al2O3 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al,O3 and of A120,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO, (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2 The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

Department of Forestry and Geological Development, 435 State Capitol, Atlanta, Ga. S W. McCalhe, State Geologist. A complete list of Bulletins of the Geological Survey of Georgia will be sent upon request. Forty-five Bulletins have been issued, most of which deal with the mineral deposits of the state and are still available; they may be had on payment of postage. The subject matter of those bulletins of most interest is indicated in the following list, with the year of issue and the mailing weight. Bulletin 1, Marbles (1894), 3 lb , 8, Road building materials (1901), 3 lb , 9, Granites and gneisses (1902), 2 lb ; 10, Iron ores (1900), 2 lb , 11, Bauxite (1904), 2 lb.; 12, Coal deposits (1904), 2 lb ; 13, Ocher deposits (1906), 2 lb.; 14, Manganese deposits (1908), 2 lb ; 17, Fossil iron ore (1908), 2 lb.; 18, Clay deposits

Jan 1, 1933

By C. E. Birchenall, H. M. Schadel

THE purpose of this study was to measure the vapor pressure of silver as the first step in the determination of activities in silver alloys and to test the limitations of the method adopted. In order to work at low pressures, below 2x10-2 mm of mercury, the orifice effusion technique was employed. To shorten the time of collection of silver from the atomic beam, radioactive silver (Ag110) was used as a tracer. The rate of effusion of a monatomic vapor from an "ideal" orifice, where the thickness of the orifice edge is negligible compared with the orifice diameter, can be readily calculated from the kinetic theory of gases, G = vM a p/v2pRT where G is the weight of material effusing from the orifice per unit time; p is the vapor pressure at oven temperature, T; R is the gas constant; M is the molecular weight of the vapor; and a is the orifice area. Consolidating constants and expressing as the weight of material effusing from the orifice in a period of time, t, (5.83)(10-2) (vM) (a) (t) (p)/vT where GT is total weight of monatomic vapor effused (g); M is molecular weight of the effusing tracer vapor; a is orifice area (cm2); t is time of effusion (sec); p is vapor pressure of effusing material (mm of Hg); and T is oven temperature (OK). The vapor effuses from the orifice in a hemispherical pattern, and the intensity of the beam in any direction is given by the cosine distribution law.' Considering this, the weight of effused material can be calculated from the amount of material passing through a circular collimator intersecting the beam. If such a collimator is in a plane parallel to the plane of the orifice and with center on the normal to the orifice center, GT = G?/1-cos2? = G?/sin2? where G? is the weight of effused material passing through the collimator, and 0 is one half the apex angle of the cone defined by the collimator circumference and the orifice center. Reducing eq 3 to the more directly measurable quantities of orifice to collimator distance, d, and collimator diameter, D, the expression becomes,

Jan 1, 1951

By E. R. Brownscombe, Francis Collins

The pressure distribution in a reservoir producing an incompressible fluid by radial flow in a horizontal structure is a simple logarithmic function' used daily by reservoir engineers. The assumption of an incompressible liquid is equivalent to assuming that pressure is maintained constant at the well radius and at some external "radius of drainage," or, in other words, that the entire flow into the well passes across the external radius. In most cases a well is surrounded by other wells draining adjoining areas so that the "radius of drainage" is not a line of constant pressure with flow equal to the flow into the well but rather a contour of zero pressure gradient across which no flow occurs, production being due to the expansion of the liquid within the area. The radial flow steady state pressure distribution for this case does not seem to be extensively used despite the fact that the mathematical analysis has been given in detail' and the results are simple and generally applicable. 'The object of this discussion is to develop this result from a physical rather than a mathematical viewpoint, thereby aiding intuition in judging circumstances to which it may be applicable. If the production rate at a well in an unsaturated reservoir is maintained constant while no flow occurs across the outer radius a steady state will soon be reached in which the flow rate or pressure gradient is constant with time at all points in the reservoir. To preserve such a condition it is necessary that the pressure decline at the same rate at all points in the reservoir, that is, the curves of pressure versus radial distance at successive times are all parallel. Then each unit volume of oil is expanding at the same rate and contributing an equal share to the production. The rate of flow q across any circle r is thus proportional to the volume of the reservoir between r and the external radius re, or q = qw (I-r2/r2e) ......(1) where q, is the production from the well and it is assumed that rw is very small compared with re. This equation can be combined with the differential form of Darcy's law for radial flow, 2phkr dp q =—— ........(2) aµß dr ( where q is not a constant as in the incompressible flow case but is a function of r given by Equation (1). If Equation (1) is substituted in Equation (2) the variables p and r can be separated and the result integrated to obtain the pressure distribution p = pw +--------In------------- 2pkh[ rw 2re2] ......(3) This equation differs from the incompressible case only in the addition of the term proportional to the square of the radius

Jan 1, 1950

By Gustav S. Preller, A. M. Gaudin

For the past 20 years it has been generally accepted that the flotation process is made possible as a result of the action of certain chemical substances on the surface of the mineral particles. In fact, it has been suspected, but never demonstrated, that this action produces on the mineral particles a layer of chemosorbed ions that is of the order of magnitude of a monolayer; that is, of a layer one ion deep. It is the purpose of this paper to present certain initial results on the relationship of mineral surface area and collecting-agent requirements. Up to about eight years ago, all considerations involving the surface area of finely divided solids were limited by the fact that there was not in existence any general method for determining the extent of such surfaces, especially on mixed materials. However, the method invented by Brunauer, Emmett and Teller1 has changed the situation by providing a general procedure (BET method). This procedure has already been applied to mineral dressing problems2-4 and has now received confirmation as to accuracy by an entirely independent method.' This confirmatory or "absolute" method uses a very tedious calorimetric procedure and is not suitable for routine determinations; but still another method6 now is available to relate the results obtained by the BET method to those obtained calorimetrically. This Harkins-Jura method has the advantage that it does not require an assumption concerning the parking area per molecule of adsorbate (nitrogen). In the original work by Brunauer, Emmett and Teller the parking area per nitrogen molecule was calculated to be either 13.8?2 or 16.2?2. according as the nitrogen was assumed to be closely packed as in crystalline nitrogen or loosely packed as in liquid nitrogen. The initial experimental work from this laboratory2 supported the 13.8?2. figure; that work was done on glass spheres of measurable geometric area and it was based on the assumption that the glass spheres were truly smooth; any deviation from this assumption would, of course, have made the calculated parking area higher. Harkins and Jura's results suggest that the parking area is not the same for all substrata; furthermore, the average of the 87 measurements cited indicates a "preferred" parking area for the nitrogen molecule of about 15.2?2., with extreme values at 13.7 and 16.9?2. The average of 21 determinations made in connection with this study7 gave a parking area of 14.3 ± 0.27?². In view of this result and of the Harkins and Jura

Jan 1, 1947

By Gustav S. Preller, A. M. Gaudin

For the past 20 years it has been generally accepted that the flotation process is made possible as a result of the action of certain chemical substances on the surface of the mineral particles. In fact, it has been suspected, but never demonstrated, that this action produces on the mineral particles a layer of chemosorbed ions that is of the order of magnitude of a monolayer; that is, of a layer one ion deep. It is the purpose of this paper to present certain initial results on the relationship of mineral surface area and collecting-agent requirements. Up to about eight years ago, all considerations involving the surface area of finely divided solids were limited by the fact that there was not in existence any general method for determining the extent of such surfaces, especially on mixed materials. However, the method invented by Brunauer, Emmett and Teller1 has changed the situation by providing a general procedure (BET method). This procedure has already been applied to mineral dressing problems2-4 and has now received confirmation as to accuracy by an entirely independent method.' This confirmatory or "absolute" method uses a very tedious calorimetric procedure and is not suitable for routine determinations; but still another method6 now is available to relate the results obtained by the BET method to those obtained calorimetrically. This Harkins-Jura method has the advantage that it does not require an assumption concerning the parking area per molecule of adsorbate (nitrogen). In the original work by Brunauer, Emmett and Teller the parking area per nitrogen molecule was calculated to be either 13.8?2 or 16.2?2. according as the nitrogen was assumed to be closely packed as in crystalline nitrogen or loosely packed as in liquid nitrogen. The initial experimental work from this laboratory2 supported the 13.8?2. figure; that work was done on glass spheres of measurable geometric area and it was based on the assumption that the glass spheres were truly smooth; any deviation from this assumption would, of course, have made the calculated parking area higher. Harkins and Jura's results suggest that the parking area is not the same for all substrata; furthermore, the average of the 87 measurements cited indicates a "preferred" parking area for the nitrogen molecule of about 15.2?2., with extreme values at 13.7 and 16.9?2. The average of 21 determinations made in connection with this study7 gave a parking area of 14.3 ± 0.27?². In view of this result and of the Harkins and Jura

Jan 1, 1947

By Robert Linton

SPECIFICATIONS for clays serving raw materials in the ceramic industry usually contain the following items: (1) Chemical analysis, sometimes with mineralogical structure determined by microscopic investigation. (2) Maturing temperature and firing range, usually expressed in terms of pyrometric cone equivalent. (3) Shrinkage (drying and firing shrinkage separately). (4) Degree of plasticity. (5) Color after firing. Clays may be classified, according to the purpose of the classification, in several different ways, based on (1) Geological occurrence-transported, altered An place, indurated (shales). (2) Physical properties-plastic (bonding clays, ball clays) and nonplastic (flint clays, kaolins or china clays, bone clays). (3) Color. (4) Use. A common classification of clays for commercial designation, and one fol-

Jan 1, 1936

By Roland Kammel, Takeo Oki

A suspension electrolysis method has been developed which enabled a direct anodic extraction of zinc from zinc sulfide concentrate and simultaneously oxidized sulfide sulfur to elemental sulfur. The investigation was performed in a laboratory-scale electrolytic cell, where the zinc sulfide concentrate particles (chemical composition in weight percent: 61.1% Zn, 2.3% Fe, 30.6% S, 3.4% SiO2 were suspended with or without graphite powder in a dilute sulfuric acid electrolyte. The main parts of the cylindrical electrolytic cell are shown in [Fig. 1]. The cathode (1), a rod of aluminum, is set at the center of the cell. The anode (2), which consists of four plates, is mounted on the inner face of the cell wall. Both PbO2(Pb) and graphite anodes were used. The cathode compartment (3) is separated from

Jan 1, 1976

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By Louis A. Panek

The purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fen tress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal held exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The miaximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repiesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: Safe R =(1/4)4p2n2r/g=p2n2r/g [I] in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sec2.

Jan 1, 1949

By J. Chipman, J. A. Cordier

Equilibrium in the reaction H2 (g) + 2 = H2S (g) was studied at 1600°C for sulphur dissolved in Fe-Ni alloys of 0 to 100 pct Ni. Within experimental accuracy, the equilibrium ratio pH2s/pH2 [pct S] is independent of the Fe-Ni ratio. Its variation with sulphur content is the same in nickel and the alloys as in iron. Recent data on dissociation of S2 into atomic sulphur are used to apply a small correction to earlier equilibrium data. Equations are presented which define the thermodynamic properties of sulphur in liquid Fe-Ni alloys. ACTIVITY of sulphur in liquid iron was determined by Sherman, Elvander, and Chipman.' The effects of a number of alloying elements on the activity of sulphur also have been determined, that of silicon by Morris and Williams,2 that of carbon by Morris and Buehl,8 and the effects of manganese, phosphorus, and aluminum by Sherman and Chip-man.' The data of Rosenqvist and Cox5 have been used to establish the effect of copper. A summary of all of these data is included in the paper by Sherman and Chipman. In each case, the experimental method depended upon the study of equilibruim in the reaction of sulphur in the liquid metal with hydrogen gas to form H,S. Despite wide differences in the design of apparatus used by the several investigators, all of the results are in excellent agreement. Experimental Study Since the experimental method has already been described,' it will be sufficient to mention its general

Jan 1, 1956

By William C. Harrigan, William D. Nix

Dynamic measurements of Young's modulus have been made for poly crystalline Ni-W alloys from room temperature to 800°C. The alloys studied range in composition from pure nickel to Ni-10 at. pct W. The results indicate that Young's modulus decreases linearly with temperature above the Curie temperature. The rate of change of Young's Modulus with temperature mas found to range from 104 psi per "C for pure nickel to 0.82 x 104 psi per °C for Mi-10 pct W. At all temperatures the elastic modulus decreases with increcrsing tungsten content up to 1 at. pct W, and increases as the tungsten content is increased above that level. Young's modulus decreases slightly as the carbon content is increased from 0.002 to 0.09 wt pct C THE knowledge of the elastic modulus of metals and alloys is important for a number of reasons. The first and most obvious reason comes from the need to predict elastic deflections under given loading conditions. A second and somewhat more subtle reason comes from the fact that the elastic properties of an alloy must be known before a proper account of the mechanisms of plastic deformation can be made. This is especially true for high-temperature creep of crystalline solids. Sherby and his coworkers have shown that the high-temperature steady-state creep rates of crystalline solids are inversely related to the elastic modulus1,2 and that the temperature dependence of the elastic modulus must be taken into account if reliable determinations of the activation energy for creep are to be made. In addition, measurements of the elastic constants of solid solutions are needed to allow one to assess the modulus interaction contribution to solid-solution Strengthening.3-5 Pelloux and Grant6 have demonstrated that substantial solid-solution strengthening at room temperature and elevated temperatures occurs when refractory metal solute atoms are added to nickel. While the high-temperature elastic properties of pure nickel have been measured by a number of authors,7-10 the elastic properties of nickel-based refractory metal alloys have not been determined. The purpose of this paper is to report on measurements of Young's modulus of polycrystalline Ni-W alloys at elevated temperatures. It is expected that these measurements will be valuable to studies of the mechanical properties of nickel-based refractory metal solid solutions. I) EXPERIMENTAL Young's moduli of polycrystalline samples were determined by a dynamic method in order to reduce high- temperature anelastic and plastic relaxations. The samples were forced in transverse free-free vibration; that is, both ends of the sample were unrestrained and the vibration was transverse to the long axis. The fundamental resonant frequency was determined by the Forster method.11 The analysis of this type of vibration which was formulated by Rayleigh,12 Timo-chenko,13 and pickett,14 and reviewed by Fine," leads where fn is the resonant frequency of the nth mode, r is the radius of the circular cross section. L is the specimen length, ßn is 1.5056 for free-free vibration in the fundamental mode of vibration, 6 is the mass density, and E is Young's modulus in the axial direction. This equation can be transformed into: E = 9.17605 x 10-6(L/D)E/Lf2 [2] where E is Young's modulus in psi, L is the length in inches, d is the diameter in inches, W is the weight in grams, and f is the resonance frequency in cps. Eq. [2] was further modified in order to take account of the thermal expansion of the samples. The resulting correct term is: where the thermal expansion coefficients for nickel and tungsten, respectively. Xw is the atom fraction of tungsten in the sample and T is the temperature in "C. The treatment of the thermal expansion coefficient as a linear function of composition seems sufficiently accurate since an error of 25 pct in the expansion coefficient will result in only a 0.3 pct error in the modulus at 1000°C. A) Apparatus. The equipment for this investigation has been described by Lytton et al.16 Several modifications of the equipment have been made. The most significant change involved replacing the detector crystal transducer with a magnetic transducer. A phonographic magnetic transducer was employed as a sensing device since the contact pressure necessary to produce a stable signal is much less than that for a crystal transducer. This magnetic transducer is also not affected by conditions of high temperature and vacuum which are present in these experiments. The vacuum was 10-5 torr at room temperature and about 5 x 10-4 torr at 900°C. This was sufficient to prevent surface contamination of the samples during the tests. The samples were heated in an elliptical furnace with a quartz lamp at one focal line and the sample at the other, as described by Lytton et a1.16 The temperature of the sample was measured by monitoring the

Jan 1, 1969

By H. R. Deeth, C. J. Koenig

ABOUT ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spence1 described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Corp. at Rochester, N. Y. THE DEPOSIT Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 [VOLUMETRIC MINERAL PER CENT Albite54 Microcline20 Nepheline22 Muscovite2 Mafics2 (Biotite, hastingsite, magnetite) Total100] The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2O A1203 6SiO2) and microcline (K20 A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1947