Search Documents

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By G. Rinelli, A. M. Marabini

A wide-ranging series of experiments has been carried out on value minerals (sphalerite, smithsonite and hematite) and gangue minerals (quartz and calcite) to assess the properties of various commercially available vegetable and synthetic tannins as dispersants for these minerals in a finely ground state (<5 microns). Experiments to determine the dispersing power of each reagents on every mineral have been performed through sedimentation tests run first in water and afterwards in the presence of a collector having specific action on the mineral concerned. The tests have been extended to a wide range of dispersant concentrations, maintaining the pH and collector concentrations at the levels known to be the best for the flotation of the various minerals. By comparing the results obtained on each mineral, conclusions have been drawn on the possibility of using different classes of vegetable and synthetic tannins in the selective flotation of fine particles. These results have been related to the structure of the tanning compounds and to the surface properties of the minerals.

Jan 1, 1980

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.&apos; Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

By H. I. Smith

WHEN Spain established colonies on the North American continent, some of her land grants, in what is now the United States, reserved to the Crown deposits of gold, silver, and mercury. Later mineral rights were reserved under some of the English Crown charters involving land in the eastern part of North America, with provisions for the payment of royalties thereon to the Crown. Reservation of mineral deposits to the United States Government was instituted by an ordinance of Congress on May 20, 1785, which applied to such deposits in the Northwest Territory, then north of the Ohio River and east of the Mississippi River, and provided that there should be reserved "one third of all gold, silver, lead, and copper mines, to be sold or otherwise disposed of as Congress shall hereafter direct." Little was known then of the mineral resources of the country; the Great Lakes copper region had just come into the possession of the United States by treaty and much of the western mineral land still belonged to France and Spain. The policy of leasing mineral deposits was enacted by Congress under the act of March 3, 1807, which provided that "the President of the United States shall be, and is hereby, authorized to lease any lead mine which has been or may hereafter be discovered in the Indiana Territory, for a term not exceeding five years," and in the same year the Government reserved 345,600 acres of land in northern Illinois, valuable for lead. In 1816 Congress provided that in all cases where a tract of public land containing a lead mine or salt spring was applied for by settlers on the public domain, no permission to work the mine or spring would be granted without the approbation of the President of the United States. By the act of March 1, 1847 (9 Stat. 146), the control of mineral lands was transferred, with all records, from the War Department to the Treasury Department, and by the act of March 3, 1849 (9 Stat. 395), supervisory powers over lead and other mines of the United States were transferred to the Secretary of the Interior. Following the discovery of gold in California in 1848, President Polk advocated the leasing of mineral lands acquired from Mexico under the treaty of 1848. However, owing to the lack of communication and transportation facilities and the consequent difficulty of checking on production and operations, leasing was found impracticable. Mining was permitted to be carried on in each district under rules made by the miners themselves and patterned after the Mexican mining system. To meet the situation, Congress enacted mining laws in 1866, 1870, and 1872, which provided for possession by location and for private ownership, after discovery, by patent of essentially all mineral deposits belonging to the United States, except coal. Many other acts were passed by Congress applying to specific regions and states, reserving salt, lead, or other minerals, some of which provided for the leasing of such deposits. However, very few if any leases were issued thereunder. Not until 1901 (31 Stat. 745) were the mining laws extended to include salt, and in 1910 they were revised to specify salines and associated products. At the turn of the century, it became more and more evident that the mining laws developed for metallic minerals were not practical for the development and conservation of oil and gas, coal, potash, phosphate, or oil shale. Following withdrawals by the Secretary of the Interior as authorized by the act of June 25, 1910, the Department of the Interior recommended leasing legislation; however, it was not until February 25, 1920, that the Mineral Leasing Act was passed by Congress. This act authorized leasing all public lands potentially valuable for oil, gas, coal, phosphate, sodium, or oil shale. The Organic Act, creating the Geological Survey in 1879, imposed upon its director the duty of classifying the public lands.&apos; The early years of the Survey were devoted largely to the accumulation of fundamental data and, with only minor exceptions, land classification was not seriously undertaken until 1906. Since that year, it has been actively pursued with respect particularly to leasable minerals and water power values. On March 3, 1873 (17 Stat. 607) Congress authorized the sale of coal lands of limited acreage to individuals at $10 to $20 an acre, depending on the distance from a railroad, and in 1907 a new scale of prices was adopted by the Secretary of the Interior, based, more logically, on the quality and thickness of the coal deposits, their depth below the earth&apos;s surface, and their accessibility. At that time it was much cheaper and easier to obtain incidental title to coal rights under the homestead laws at $1.25 an acre. On March 3, 1909, the first separation act (35 Stat. 844) became a law. It authorized patents, with a reservation of the coal and mining rights involved to the United States, to persons who in good faith had entered public lands under the non-mineral land laws prior to withdrawal, classification, claim, or report that such lands were valuable for coal. It solved the problem only partially, and the practice thereupon adopted by the department of making coal withdrawals "from all forms of entry" instead of "from coal entry" expedited the more complete solution effected by later acts. By the act of June 22, 1910 (36.Stat. 583) withdrawn and classified coal lands were declared subject to entry under the homestead, desert land, and Carey acts, provided a waiver of the coal rights accompanied the application, and by the act of April 30, 1912 (37 Stat. 105) the same privilege was extended to State selections and isolated tracts. The act of August 24, 1912 (37 Stat. 496) extended the separation policy to lands withdrawn for oil and gas in Utah, and finally the act of July 17, 1914 (38 Stat. 509) extended it to all nonmineral filings on public lands theretofore or thereafter

Jan 1, 1955

By AIME AIME

Acid Open-Hearth Manipulation.. By ANDREW MCWILLIAM and WILLIAM H. HATFIELD, ii, 279. Discussion by J. J. MORGAN, iii, 647; E. H. SANITER, iii, 648; MCWILLIAM and HATFIELD, 111, 648. ADDICKS, LAWRENCE. The Effect of Impurities on the Electrical Conductivity of Copper, iii, 559. Address of Welcome to the U. S. National Museum, Washington, D. C. By RICHARD RATHBUN, .iv, 923. ALLDERDICE, TAYLOR. Discussion of MR. ROE&apos;S paper, The Mann¬ facture and Characteristics of Wrought Iron, v, 1091. American Mining Engineer. Discussion by ARTHUR JARMAN, iii, 641. An Automatic Stock-Line Recorder for Iron Blast-Furnaces. By J. E. JOHNSON, JR., iii, 509. Anthracite-Washeries. By GEORGE W. HARRIS, vi, 1263.

Jan 1, 1907

By George J. Young

The nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker&apos;s stand-point has also received much comment, arid scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of niore intensive study and experimeritation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has been written concerning an accurate definition of the term "slime," but no comprehensive definition seems to be gcnerally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may bc and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles niuch more slowly and finally a certain portion remains

Jan 1, 1912

By Robert Goodwin, Frank R. Milliken

IN September 1939, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about 1 per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig.1, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of [ ] which ranged from 62 to 74 per cent recovery. On the basis of these, a Zoo-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1940

By C. G. Fink

A PART of the material incorporated in this paper was derived from the studies of ancient metal objects examined by the authors from time to time for museums and art collectors, in order to verify the age of the metal. The data thus accumulated during several years was systemati-cally surveyed and supplemented by new material obtained in examina-tion of a set of specimens that had been generously donated by museums for this study. Altogether over 50 pieces were investigated, of which 39 are described in this paper. Every specimen is at least 1500 years old; the majority are considerably older. Exact conditions to which these bronze and copper objects were exposed in the ground are unknown, unfortunately. It is safe to say that exposure conditions did not remain constant during the long period of burial. Although the collection of specimens studied represents a wide variation in location and age of the objects, as well as in the nature and composition of the metals, it was found that fundamental changes in the metal structure were limited to a few typical cases which, therefore, may be considered as more or less general. The authors&apos; chief aim was to study the effect of extremely long periods of corrosion on the structure of bronze and copper.

Jan 1, 1936

By K. P. Gupta, A. K. Pal, L. Chandrasekaran, U. P. Singh

The Mn-Sn binary system, investigated at the high-manganese end and between 500° and 1000° C, shows four phases at temperatures below 727"C, namely the u Mn, the p Mn, the Mn3 Sn, and the Mn, Sn phases, while at higher temperatures only the last three phases remain stable. The solubility of tin in a Mn is very small and the maximum solubility of tin in P Mn phase appears to be abollt 10 at. pct Sn. The solubility range of the Mn,Sn and the Mn, Sn phases is 23.0 to 26.0 and 37.0 to 40.0 at. pct Sn, respectively. The lattice parameter of the 13 Mn phase increases with increasing tin content. The Mn, Sn thase is hexagonal with and appears to be basically of the Ni3 Sn type structure except that for quite a few X-ray diffraction lines the calculated and observed relative intensities do not agree well. The Mn-Sn binary system has been studied by several investigators.&apos;&apos;~ Their results indicate that three intermediate phases, namely, the Mn3Sn, Mn,Sn, and MnSn, phases, exist at high concentrations of tin. However, so far the proper phase equilibrium has not been established at the manganese-rich end and very little data is available for the composition range between pure manganese and Mn3Sn. Moreover, earlier investigators differ in their opinion about the exact composition range at which the Mn3Sn and Mn,Sn phases appear and some doubt has been cast by some investigators3 regarding the structure of Mn3Sn phase which has been reported to be isotypic with Ni3Sn (Mgscd type) structure. In this investigation an attempt has been made to establish the proper phase equilibrium between pure manganese and Mn + 50 at. pct Sn composition in the temperature range of 500" to 1000°C. PROCEDURE The raw materials used were from three different sources. For exploratory work five alloys containing 5, 10, 15, 20, and 25 at. pct Sn were prepared using 99.9 pct pure manganese and tin supplied by E. Merck & Co., Germany. The rest of the alloys and one more 25 at. pct Sn alloy were prepared using 99.9 pct Mn supplied by Gallard Schlesinger Chemical Mfg. Corp., U.S.A., and 99.999 pct Sn supplied by Semi Elements Inc., U.S.A. Weighed amounts of manganese and tin were melted in recrystallized alumina crucibles in an inert gas (argon) high-frequency induction melting furnace. By careful control of temperature and time of melting the losses were reduced to below 0.2 pct in all cases. Since the losses were very small, no attempt was made here to analyze the samples chemically. Alloys were wrapped in molybdenum foil and sealed in small evacuated fused silica capsules. The alloys were annealed at different temperatures, controlled within + l°C, for sufficiently long periods to attain proper phase equilibrium, and subsequently quenched in cold tap water. The annealing periods used at different temperatures were 15 days at 500°C, 7 days at 600°C, 5 days at 700" and 750°C, 3 days at 800°, 850°, and 900°C, 2 days at 968"C, and two alloys annealed at 968°C were reannealed for 10 hr at 1000° C. From each annealed specimen, a part was utilized for metallographic study while another piece was used for X-ray diffraction study. 1.0 pct HNO, solution and oxalic acid solutions of concentrations 0.05 to 1.0 pct were used for etching Mn-Sn alloys above and below the MnsSn composition, respectively. Since all alloys were brittle, X-ray specimens were prepared using the as-crushed -325 mesh alloy powders. Only one 25 at. pct Sn alloy powder was reannealed in an evacuated silica capsule at 800°C for 5 min and water-quenched. X-ray diffraction patterns . for the Mn3Sn phase with the as-crushed and the reannealed powders did not show appreciable change. Un-filtered iron radiation at 25 kv, 15 ma was used with either Norelco 114.6-mm-diam Debye Scherrer Camera (for phase identification) or Norelco 12-cm-diam symmetrical focusing camera (for lattice parameter determination of the 6 Mn phase). The estimated accuracy of lattice parameter determination for the focusing camera was * 0.001A. RESULTS AND DISCUSSIONS The results of metallographic and X-ray diffraction study made with different alloys are shown in Fig. 1. The variations in lattice parameter with composition for the p Mn and the Mn3Sn phases are given in Tables I and 11, respectively, and the lattice parameter as a function of composition for the p Mn phase is shown in Fig. 2. The lattice parameter of the p Mn phase increases with increasing tin content while for the Mn,Sn phase the data obtained from two two-phase alloys and one single-phase alloy indicate increase in a,, and decrease in c, parameters with increasing tin content. The results, Fig. 1, indicate that the solubility of

Jan 1, 1969

Jan 1, 1902

By John McDonald

THIS report is a continuation of an earlier one with a similar title,1 to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as re-ported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be com-pared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a con-siderable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated.

Jan 1, 1940

Page Laboratory Methods...........................127 Special Analytical Methods.......................127 Improvements in the Accuracy of the Vacuum-fusion Method for the Determination of Oxygen in Steel....................127 Quantitative Spectrochemical Analysis of Mixtures of Gases.......131 Oxygen Samples from Open-hearth Bath...............133 Rapid Analysis of Sample for Alumina.................139 Accurate Carbon Analyses in Low-carbon Steel.............139 Laboratory Technique for Study of Reactions Involving Liquid Metal. . . . 142 Rotating Liquid Crucibles......................143 Stationary Crucibles.........................145 Jones and Laughlin Experimental Furnace...............148 Vacuum Melting..........................149 Measurement of Temperature of Liquid Iron and Steel;..........149 Pouring and Teeming Temperatures..................149 Bath Temperatures.........................151 Plant Methods.............................154 Methods of Studying Slags.......................154 Sampling Slag in the Open Hearth..................155 Viscosity of Open-hearth Slags....................155 Petrographic Examination of Slag...................156 Statistical Methods Applied to Study and Control of Chemical Relations in Bath...............................166 Rapid Method of -Correlation Applicable to Study of Steelmaking Reactions............................166 INTRODUCTION On Thursday morning, Feb. 16, 1939, a round table discussion was held on the subject of Experimental Methods in the Study of Steelmaking. Dr. John Chipman, Professor of Metallurgy at the Massachusetts Institute of Technology, and chairman of the A.I.M.E. Committee on Physical Chemistry of Steelmaking, presided. In opening the meeting, the chairman said: "The purpose of this round table is to discuss methods of study by which more and better information on the fundamentals of steelmaking can be obtained. It was thought that a round table discussion rather than a symposium would furnish the best opportunity for those actually using various methods of study to get together and discuss their common problems. For this reason attention will be focused upon methods of study rather than upon their results. We want new and current and up-to-date discussion.

Jan 1, 1940

Page Laboratory Methods...........................127 Special Analytical Methods.......................127 Improvements in the Accuracy of the Vacuum-fusion Method for the Determination of Oxygen in Steel....................127 Quantitative Spectrochemical Analysis of Mixtures of Gases.......131 Oxygen Samples from Open-hearth Bath...............133 Rapid Analysis of Sample for Alumina.................139 Accurate Carbon Analyses in Low-carbon Steel.............139 Laboratory Technique for Study of Reactions Involving Liquid Metal. . . . 142 Rotating Liquid Crucibles......................143 Stationary Crucibles.........................145 Jones and Laughlin Experimental Furnace...............148 Vacuum Melting..........................149 Measurement of Temperature of Liquid Iron and Steel;..........149 Pouring and Teeming Temperatures..................149 Bath Temperatures.........................151 Plant Methods.............................154 Methods of Studying Slags.......................154 Sampling Slag in the Open Hearth..................155 Viscosity of Open-hearth Slags....................155 Petrographic Examination of Slag...................156 Statistical Methods Applied to Study and Control of Chemical Relations in Bath...............................166 Rapid Method of -Correlation Applicable to Study of Steelmaking Reactions............................166 INTRODUCTION On Thursday morning, Feb. 16, 1939, a round table discussion was held on the subject of Experimental Methods in the Study of Steelmaking. Dr. John Chipman, Professor of Metallurgy at the Massachusetts Institute of Technology, and chairman of the A.I.M.E. Committee on Physical Chemistry of Steelmaking, presided. In opening the meeting, the chairman said: "The purpose of this round table is to discuss methods of study by which more and better information on the fundamentals of steelmaking can be obtained. It was thought that a round table discussion rather than a symposium would furnish the best opportunity for those actually using various methods of study to get together and discuss their common problems. For this reason attention will be focused upon methods of study rather than upon their results. We want new and current and up-to-date discussion.

Jan 1, 1940

By W. Francis

OF THE methods that have been used for studying the chemical composition of coal, attack by reagents has not, in general, yielded much information. Most of the reagents used have been strong oxidants such as nitric acid or Schulze&apos;s solution. The use of a milder oxidizing agent, such as air at low temperatures, enables progressive changes in the character of the coal substance to be studied and thus helps toward an understanding of its constitution. British bituminous coals frequently have a banded structure. These bands (of four types) can be separated one from another and have been found to possess markedly different chemical characteristics, even when taken from contiguous portions of the same lump coal. It has been found convenient to give each of the ingredients of banded coal a distinctive name, more or less descriptive of its appearance, and the study of the chemistry of bituminous "coal" in England has resolved itself into a study of each ingredient separately. . The coal chosen for this work was taken from the Top Hard seam at East Kirkby colliery, Nottinghamshire, a detailed chemical analysis of which has been recorded by Baranov and Francis.1 The banded structure was well marked and the bands could readily be separated. The research was confined to the brilliant vitreous bands (vitrain), the dull hard bands (durain) and the "sooty partings" (fusain); for previous work had shown that the fourth type, to which the name clarain has been given, is intermediate in character, chemically, between vitrain and durain.

Jan 3, 1925

By L. W. Blau

THE entrance of geophysics and geochemistry into petroleum engineering may be viewed with apprehension by some engineers. They may not remember the time when "practical oil men" opposed the invasion of engineers into the field of petroleum production. By their excellent contributions they established themselves. In the popular mind, engis veers are practical men whereas physicists and chemists are suspected of being theoretical. It will be best to annihilate this misconception right now at the beginning of a closer relationship between petroleum engineers. geophysicists, and geochemists.

Jan 1, 1943

By G. M. Ritcey

The design of the plant facilities together with the necessary equipment required for the operation is at an optimum only for the specified plant with its peculiar priorities and preferences. Because many alternatives in design are possible to suit a particular plant, each plant designer and contractor must choose carefully in the selection of the site, design and choice of materials of construction, as well as the type of equipment necessary for the process. Basic factors as efficiency, dependability, simplicity, and safety must be considered early in the construction; while the choice of equipment, materials of construction, possible corrosion problems, automation, maintenance, effluents disposal and tailings dam construction can greatly affect the plant costs. While existing plants are in operation, the know-how gained from the operating experience of those plants can be invaluable in the new plant planning, design, and construction.

Jan 1, 1978

By Ralph W. M. Lai, D. W. Fuerstenau

In aqueous solution, an oxide surface is considered to consist of positively charged surface sites, MOH, neutral surface sites MOH, and negatively charged surface sites MO-. From the mass action law, equations for the distribution of these sites have been derived in terms of the hydrogen ion concentration in solution and the point of zero charge of the oxide. Experiments on the flotation of futile were carried out with sulfonates and amines which are collectors that physisorb, and with oleate, which is a collector that chemisorbs. Flotation response was found to correlate with the site distribution model. A similar correlation was found with published data on iron oxide potation.

Jan 1, 1977

By Robert Bell

THE " Tar-Sands." is the name which has been given to the extensive horizontal deposit of fine Cretaceous sand, blackened by tarry petroleum, which forms the banks of the last or lowest 130 miles of the Athabasca river before it terminates in Athabasca lake. The Cretaceous strata, to which these sands belong, extend northwesterly from Dakota all the way to this lake and for 500 miles beyond it. The Athabasca river forms the uppermost section of the Athabasca-Mackenzie, one of the great rivers of the world. It rises on the Pacific side of the Rocky mountains, westward of Edmonton, and flows north of east to a point called Athabasca. Landing, 100 miles north of Edmonton, where it turns northward and runs about 280 miles before it falls into the west end of Athabasca lake. The section of this river-system which discharges the lake just named into Great Slave lake, is called Slave river, and below the latter lake it becomes the Mackenzie river. Along the section of 280 miles of the Athabasca river above mentioned, the Cretaceous strata consist of bluish-gray and drab-gray marls, on top, from Athabasca Landing to Drowned rapid, 110 miles down stream; then heavily bedded gray sandstones, 225 ft. in greatest thickness, underlying these, form the banks for about 40 miles further. The strata appear to be horizontal, but they really clip very slightly to the southward. At Drowned rapid, we see the first of the tar-sands resting on almost horizontal beds of bluish-gray limestone of Devonian age. In some places the limestone is associated with shaly or marly bands. Notwithstanding the great hiatus between the two series, the horizontal tar-sands lie conformably upon the almost level upper beds of the limestone wherever the two formations are seen together, all along the river, throughout a

Mar 1, 1908

By N. Brown, M. Herman

IT has been pointed out by Cottrell&apos; and Fisher that long-range order would produce superdis-locations, consisting of two partial dislocations separated by an out-of-phase region. The mutual repulsion of the partial dislocations is balanced by the surface tension of the out-of-phase domain boundary joining the dislocations (Fig. 1). The calculation of the equilibrium spacing of the dislocations has yet to be made. The argument uses the Bragg and Williams theory of long-range order." The metal under consideration is the A-B, body-centered type, such as ß brass. The slip system is taken to be [Ill], (110). Since nearest-neighbor interactions are considered, only the atoms position in the two (110) planes adjoining the slip plane have to be labeled. Corner sites are called a and a&apos; in the top and bottom (110) planes, respectively. Similarly ß and ß are the body-centered sites. Thus, a and ß and 0 and a sites are nearest neighbors. Assume that the bottom plane moves and the top plane is fixed during slip; the atoms in a and ß sites exchange sites but atoms in a and ß sites remain fixed. Fraction of A atoms in a sites, for example, is given by fa and fa. for the un-slipped and slipped condition, respectively. Similarly number of A atoms in the a sites is given by n, and n&apos;a for the unslipped and slipped condition, respectively. As the dislocation moves into the ordered region the change in number of A-A bonds is given by

Jan 1, 1957

By Gerhard Derge

THE orientation relationships resulting from allotropic transforma-tions and the formation of segregate structures in metals and alloys have been the subject of the eight earlier papers in this series1. A brief summary of orientation studies has also been given by Sachs2. A survey of these papers discloses that the factors that determine the orientation relationship of a precipitated phase to its parent solid solution, as Well as the outward form and appearance of the new phase, are not completely understood. It is now evident that crystallographically analogous systems, as a rule, exhibit the same type of Widmanstätten figure and orientation relations, so that useful information is not to be expected from examination of a new alloy involving lattice combinations of which the orientation relationships are already known. Therefore, the determina-tion of the relations existing between lattice types that have not already been studied seems to be the most promising mode of attack upon the problem; both of the systems reported in this paper represent new com-binations of lattice types.

Jan 1, 1937