Search Documents

By J. L. Huiatt, M. C. Fuerstenau, M. C. Kuhn

Dithiophosphatogen is the species responsible for flotation of pyrite when dithiophosphate is added as collector. Oxidation of collector apparently occurs by reaction with oxygen adsorbed on the pyrite surface. Oxidation of dithiophosphate and xanthate is also effected with Cu++, Cu(OH) , and Fe+++ and rates of oxidation are presented as a function of pH. Reasons for the selectivity observed when dithiophosphate is added as collector in a natural ore system as compared to xanthate are presented and discussed.

Jan 1, 1972

By H. R. Spedden, A. M. Gaudin, M. P. Corriveau

A preliminary study of silver ion adsorption by sphalerite in ion exchange column with influent electrolyte marked with radiosilver is described. Rapid ion exchange occurs at first followed by slow reaction controlled perhaps by solid state diffusion. One experiment with radiocopper instead of radiosilver is reported briefly. IT has been known for many years that sphalerite is floated after it has been activated by a metallic cation, particularly copper.' The activation of sphalerite by copper is known to be an exchange of an atom of copper for an atom of zinc at the surface of the sphalerite.2,3 It has been estimated from various guesses of the available mineral surface that the depth of the copper-bearing coating is of the order of thickness of one atom. However, the exact mechanism of the activation process is unknown. A number of metals other than copper act in the same general manner."' " In particular, it has been known that silver replaces zinc at the surface of sphalerite. As copper is usually divalent, whereas silver is monovalent, it may well be assumed that there are differences, perhaps major differences, in the detailed scheme of activation by these two cations. Furthermore, since silver has unusual photoelectric properties and may be a contributor to the fluorescence of sphalerite, a study of its activating mechanism might open up some interesting avenues for exploring these other phenomena. The choice of silver as an activator of sphalerite was suggested also by the fact that its radioactive tracer, silver 110, is particularly convenient in that it has a long half-life and is energetic enough to permit counting through a counter window. The experimental technique selected, therefore, included the preparation of solutions of silver nitrate con- taining a proportion of active silver nitrate sufficient to give convenient counting data. In further considering the method to be used, a desirable choice seemed the use of batch experimentation in which a given solution was allowed to act on a certain lot of mineral for a given length of time at a given temperature, this period of mutual reaction being followed by analyses of the separated solid and solution. But an alternative method seemed more attractive. This is the method now so familiar to the users of ion-exchange resins, which was first made famous by the Russian chromatographer, Tswett.6-8 It consists in forming the mineral into a porous column through which the solution is allowed to flow at a constant rate. The usual method of allowing a batch of solid to react with solution is the equivalent of a single plate distillation operation while the chromatographic or ion-exchange column is a multiple-plate method—the multiplicity of the plates being represented by the reciprocal of the rate of flow of solution through the column. It seemed to us that the chromatographic method had such

Jan 1, 1952

By J. H. East, E. R. Maize

INTRODUCTION PROBABLY no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines, testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. So far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. ADJUSTMENTS OF DIESEL ENGINES FOR UNDERGROUND USE A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn 1 lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:I, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Diesel operates in confined places should contain less than 1/2 pct of carbon dioxide and at least 20 pct of

Jan 1, 1947

By J. W. Halley, G. L. Plimpton

BECAUSE of the two distinct stages in the solidification of rimmed steel, segregation in the rimmed ingot is more complex than that in the killed or semikilled ingot. In the earlier stage, chemical reactions, resulting in evolution of gas and vigorous stirring of the metal, effect a degree of negative segregation unique to rimmed steel. The composition of this zone constitutes the principal quality advantage of this type of steel. In the later stage of solidification, after the evolution of gas has ceased, the segregation follows the general pattern of a more completely deoxidized steel. However, the composition of the liquid remaining after the first solidification stage varies markedly from that of the original melt, some constituents having been partially removed as reaction products while the concentration of others has been intensified by rejection from the metal solidifying in the first zone. The aim, from the standpoint of segregation, in rimmed steel of high quality is to effect a maximum negative segregation in the rim zone without excessive concentration of undesirable elements at the center of the ingot. To achieve this aim, the composition of the melt may be varied and the furnace and pouring practice may be adjusted within certain limits. It is the purpose of this study to discuss segregation in rimmed steel from the standpoint of the mechanisms that produce it and to survey the phases of open-hearth practice that influence those mechanisms. MECHANISMS PRODUCING SEGREGATION The mechanisms that determine the degree of segregation in the rimmed ingot are closely interrelated, making it difficult to select the primary factors and to determine a satisfactory order for presenting them. For instance, the question of sulphur segregation is relatively simple, since sulphur is not directly involved in chemical reactions in the ingot; but its concentration in the rim zone is dependent not only on its original analysis in the melt, its segregation coefficient, and the freezing rate, but also on the rate of its removal from the impure film on the solidifying surface. This washing action involves all the factors (such as freezing rate, the carbon-oxygen product, pressure, etc.) that determine the rate of gas evolution and hence the efficiency of film removal. Sulphur distribution between the rim and core is affected by the volumetric ratio between the two zones, and its segregation in the core is a function not only of the freezing rate of the core but also of all the foregoing factors that determine its concentration in the metal when solidification of the core starts. To simplify the presentation, it is proposed to treat the mechanisms affecting segregation independently in this section, reserving a discussion of their over-all effects for the section in which actual segregation data are given. The factors affecting segregation will be treated in the following order: (I) differential solidification, (2) removal of constituents as

Jan 1, 1944

By D. E. Hawk, R. F. Burdyn, F. D. Patchen

Earlier work on a mud separator for barite recovery is extended to the design and construct ion of a rugged field unit. Problems associated with scale-up for field use include the me of dilution water and its effect on capacity, power requirements and pressures developed. Equations for these quantities are derived and applied in maximizing the beneficial effects of dilution and minimizing the power required. Tests on the full-size rotor show that its performance can be predicted by theory. The completed unit is compact and lighter than current decanting types. Its capacity is from 10 to 22 gal/min with corresponding barite recovery efficiencies of 92 to 86 per cent. INTRODUC'TION In an earlier publication a new type of centrifugal device was described for solid-liquid separations.l In that paper an operating equation was derived, and its validity demonstrated in laboratory scale experimentation. Some of the features apparent in this new device seem particularly well suited to the conservation of barite in field drilling-mud systems, hence the development was extended to the design and construction of a field unit. In the present paper the design problems associated with scale-up are considered. A full-scale, rugged self-contained field unit is described, and test results discussed which verify that the performance of the large field unit can be described by a simple operating equation. PRINCIPLE OF OPERATION OF SEPARATOR In principle, the new device is simply a perforated cylinder rotating within a body of fluid which is contained within a stationary case, as in Fig. 1. The frictional drag generated by the rotating cylinder causes part of the fluid to rotate. At the surface of the cylinder, assuming no slip occurs, the angular velocity of fluid and of the cylinder are identical. If there are suspended particles present of greater density than the fluid, the centrifugal force acting on these particles causes them to move radially away from the cylinder at some velocity vp . Where the Stokes settling equation holds, this velocity may be expressed as:2 d2 ?p rw2 If the case is provided with openings at both ends, a suspension can be pumped in at one end at a fixed rate. Part of the suspension can then be removed at a fixed rate at the other end of the case as underflow, and the remainder forced through the perforations and hollow shaft of the rotor to appear as effluent, also at a fixed rate. The radial component of the flow velocity of this stream as it reaches the rotor surface, is simply effluent flow rate divided by cylindrical surface area: Because up is a function of particle size, for some particular particle size, the velocities vp and v, will be equal in magnitude. This is defined as the critical particle size and represents the size above which all particles appear in the underflow and below which all particles appear in the effluent. For this equilibrium condition at the rotor surface, Eqs. 1 and 2 combined give

Jan 1, 1966

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By John V. Beall, William F. Haddon

A long the mighty Andean Cordillera, there is splendor beyond imagination-in the natural beauty of the mountains and in daring engineering and lavish investment in the mines. This is the story of the great copper mines of Chile and Peru. Each mine has a special quality which has tested the physical and spiritual resources of the founder. In the early days of the older mines, the mining engineer of song and story was more the rule than the exception. He was physically tough, ingenious and a leader of men. In the current political and social environment of Chile and Peru, the foreign contract mining engineer is still needed; but he must be a different type of man. To John J. Selters at Cerro&apos;s Rio Blanco, the principal ingredient is still "toughness," but it is "toughness of mind" that is needed. "He probably should be a teacher." The copper mines are not new. They were, almost without exception, worked by Indians (La Exotica might prove the rule), and later by the intrepid Spaniards. Modern mining began after the turn of the century. In Chile, the first of the big ones was the Braden Copper Co. founded on the El Teniente deposit. This development was followed by Chile Exploration Co. at Chuquicamata and Andes Copper at Potrerillos. These properties have been developed over the years by vast expenditures of money and a monumental amount of labor. None was free of technical problems-metallurgy at Chuqui, marginal grade of the old mine at Andes, avalanches and the great fire at El Teniente. The evolution which has brought the established mines of Chile, and the new ones coming on stream, to their present state of development is in reality the work of wonders of input-money, engineering and responsible management in an atmosphere of political stability. Without any one of these, the result would have been failure.

Jan 11, 1969

Executive Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. AUGUSTUS H. EUSTIS, Secretary, 131 State St., Boston, Mass. The twelfth meeting of the Boston Section was held at the Engineers&apos; Club, 2 Commonwealth Ave., Boston, on Monday evening, May 5, 1913, fifteen members and three guests being present. The meeting was called to order by Vice-Chairman Albert Sauveur, who introduced the speaker of the evening, Utley Wedge, of Ardmore, Pa. Mr. Wedge read his paper on the chloridizing roasting of copper ores, which he illustrated with a stereopticon, and which will be published in full by the Institute. After Mr. Wedge had closed his paper, which was received with great interest by all the members, the following discussion took place: Professor Hofman said that iron was formerly thought to ho essential to the Henderson process, but that it is not absolutely essential. Mr.Wedge said that, as far as he. knew, the presence of some sulphates was an abso¬lute necessity, and that line ores can be worked satisfactorily, although lime has an effect on the subsequent leaching. He added that the low fuel consumption of the latest Wedge furnace is a result of direct application of the combustion gases to the ore. Ten per cent. of fuel was needed with the muffle furnace. By direct firing he has been able to reduce the fuel needed to from 2 to 4 per cent. In the latest types of furnaces the gases from the upper hearth are not used. There is doubtless some temperature at which the loss. from copper chloride volatilization becomes serious, but in practice on Rio Tinto ores troublesome losses are not experienced. The copper apparently does not become volatile at. the temperatures where we would expect that it would. There are doubtless ores in which there would be serious danger from losses from this source. The latest furnaces do not use the high temperatures that were needed in the former single-hearth Wedge furnaces.

Jan 7, 1913

By W. M. Gray

The determination of the state of stress existing at a point in any solid body requires the determination of the six components of the stress tensor relative to a convenient set of axes. One general method of doing this in rock is to make strain or deformation measurements associated with local relief of stress in a number of boreholes penetrating a limited volume in the vicinity of the point at which the stress is to be determined. The stress is assumed to be constant throughout this volume. Leeman1 has described a number of the instruments that have been developed for making deformation or strain measurements in boreholes. Panek2 has described the application of statistical methods to the determination of the average components of ground stress from sets of measurements made in boreholes by means of deformation meters of the type developed by the U.S. Bureau of Mines. In this paper attention is given initially to the strain cell developed for use on the flattened ends of boreholes by the Council for Scientific and Industrial Research (CSIR) , South Africa. The equations required for evaluating the average components of ground stress from measurements made by means of the CSIR strain cell are derived. These equations are similar in form to those applying to measurements made by the borehole deformation meter developed by the U.S. Bureau of Mines. The results of an investigation of the properties of the equations are described. These results are important in the practical use of both the instruments mentioned above and any instrument based on similar principles.

Jan 1, 1968

By K. H. Coats

This paper presents the development and solution of a mathematical model for aquifer water movement about bottom-water-drive reservoirs. Pressure gradients in the vertical direction due to router flow are taken into account. A vertical permeability equal to a fraction of the horizontal permeability is also included in the model. The solution is given in the form of a dimensionless pressure-drop quantity tabulated as a function of dimensionless time. This quantity can be used in given equations to compute reservoir pressure from a known water-influx rate, to predict water-influx rate (or cumulative amount) from a reservoir-pressure schedule or to predict gas reservoir pressure and pore-volume performance from a given gas-in-place schedule. The model is applied in example problems to gas-storage reservoirs, and the difference between reservoir performances predicted by the thick sand model of this paper and the horizontal, radial-flow model is shown to be appreciable. INTRODUCTION The calculation of aquifer water movement into or out of oil and gas reservoirs situated on aquifers is important in pressure maintenance studies, material-balance and well-flooding calculations. In gas storage operations, a knowledge of the water movemenr is especially important in predicting pressure and pore-volume behavior. Throughout this paper the term "pore volume" denotes volume occupied by the reservoir fluid, while the term "flow model" refers to the idealized or mathematical representation of water flow in the reservoir-aquifer system. The prediction of water movement requires selection of a flow model for the reservoir-aquifer system. A physically reasonable flow model treated in detail to date is the radial-flow model considered by van Everdingen and Hurst.1 In many cases the reservoir is situated on top of the aquifer with a continuous horizontal interface between reservoir fluid and aquifer water and with a significant depth of aquifer underlying the reservoir. In these cases, bottom-water drive will occur, and a three-dimensional model accounting for the pressure gradient and water flow in the vertical direction should be employed. This paper treats such a model in detail — from the description of the model through formulation of the governing partial differential equation to solution of the equation and preparation of tables giving dimensionless pressure drop as a function of dimensionless time. The model rigorously accounts for the practical case of a vertical permeability equal to some fraction of the horizontal permeability. The pressure-drop values can be used in given equations to predict reservoir pressure from a known water-influx rate or to predict water-influx rate (or cumulative amount) when the reservoir pressure is known. The inclusion of gravity in this analysis is actually trivial since gravity has virtually no efFect on the flow of a homogeneous, slightly compressible fluid in a fixed-boundary system subject to the boundary conditions imposed in this study. Thus, if the acceleration of gravity is set equal to zero in the following equations, the final result is unchanged. The pressure distribution is altered by inclusion of gravity in the analysis, but only by the time-constant hydrostatic head. The equations developed are applied in an example case study to predict the pressure and pore-volume behavior of a gas storage reservoir. The prediction of reservoir performance based on the bottom-water-drive model is shown to differ significantly from that based on van Everdingen and Hurst&apos;s horizontal-flow model. DESCRIPTION OF FLOW MODEL The edge-water-drive flow model treated by van Everdingen and Hurst1 is shown in Fig. la. The aquifer thickness b is small in relation to reservoir radius rb. water invades or recedes from the field at the latter&apos;s edges, and only horizontal radial flow is considered as shown in Fig. 1b. The bottom-water-drive reservoir-aquifer system treated herein is sketched in Fig. 2a and 2b. Here the aquifer

The Jeffrey operation of Canadian Johns -Manville Co. , Ltd., at Asbestos, Quebec, is considered to be the world&apos;s largest asbestos mine. It accounts for approximately 37% of Canadian production of chysotile asbestos and about 13% of world production. Rated capacity is over 600,000 stpy (540,000 mtpy) of fiber, of which well over 90% is exported to the United States and seventy other countries. During the early 1970&apos;s the company completed a five-year modernization and expansion program which included the installation of a unique 72 in. by 93 in. gyratory crusher to handle the extremely blocky serpentinized peridotite ore. Because of the large diameter of this crusher the top ring of the shell was made in two halves which were bolted together. Hundred-ton trucks dump from two sides of the crusher into the 200 st (180 mt) dump pocket which is equipped with dust collecting ducts in the walls of the other two sides. The installation was designed to accommodate the eventual use of 200 -ton trucks. Crushed ore at a. size of 7 ½ in. (191 mm) falls into a uniquely designed crushed ore pocket equipped with three sloping steel sides and one vertical side, which make it totally live. Infrared heaters installed in back of the hopper sides prevent the ore from sticking to the steel. Another interesting feature is an eccentric removal bridge which is permanently mounted inside the crushed ore pocket. The two halves of the bridge are let down by electric winches to form a platform on which the eccentric cart travels and from where maintenance is done. Level indications in the crushed ore pocket are by radioactive indicators. Under the crushed ore pocket is a 72 in. by 28 ft (1.83 m by 8.5 m) apron feeder which operates at 7. 2 to 50 fpm (2. 3 to 15. 3 mpm). Crushed ore is discharged to a picking belt for tramp removal. A crossbelt magnetic separator is also mounted over this belt. Permanently mounted belt reels are also situated over the picking belt to facilitate the changing of this unit. A 60 in. (1. 52 m) wide takeaway belt then elevates the crushed ore to t.he surface facilities. Instead of discharging to a crushed ore stockpile, the takeaway conveyor delivers the ore to a 300-ton distribution bin. The ore is then screened and secondary crushed; and the plus ¾ in. (19 m) is "stored in a 3,000 ton bin while the minus ¾ in. is dried and then sent to storage. This system of directly screening primary crushed ore is similar to that used at both the Endako molybdenum and Gibraltar copper operations in British Columbia. While it would seem connecting processing equipment directly to a primary crusher would have an adverse effect on the crusher availability, the 94% of scheduled time this crusher

Jan 1, 1978

By Curtis L. Graversen, J. H. Hamilton, John C. Nixon, John R. Lewis

RECENTLY there has been much speculation concerning the advantages of using oxygen enriched air or pure oxygen in pyrometallurgical processes. The advantage of using oxygen in the iron blast furnace and elsewhere in ferrous production metallurgy has been given careful consideration and, as a result, several experiments have been tried and a number of papers have recently appeared on this subject.1.2 The use of oxygen in nonferrous smelting likewise poses interesting problems, therefore any experimental data obtained in this area should likewise be of general interest.3 Ashcroft4 in 1933 claimed to have obtained improved results when copper concentrates were roasted in pure oxygen. However, his&apos; paper gives neither data nor experimental details. A few years ago a research program was started in this laboratory which had for its objective the determination of the mechanism of oxidation of metallic sulfides under varying conditions. To date we have studied the oxidation of galena, 5 sphalerite, and chalcocite. It is a well known fact that copper sulfide minerals are oxidized slowly by weathering agents, so that the sulfides of copper which find their way into a tailing pond are gradually changed into watersoluble and acid-soluble compounds. Commercially, the oxidation of copper sulfide minerals is accomplished by roasting them at elevated temperatures in air using a suitable (usually multiple-hearth) roaster. Most copper smelters are equipped with such roasters. In this phase of the study we were especially interested in determining the effect of temperature on: (I) the air oxidation of chalcocite and (2) the oxidation of chalcocite using commercial oxygen. The amount of sulphur removed as sulphur dioxide, the percentages of water-soluble copper, and of acid-soluble copper were determined for the air oxidation tests. In the tests using commercial oxygen, the percentages of sulphur dioxide, water-soluble copper, acid-soluble copper, water-soluble sulphur and acid-soluble sulphur were determined. For these experiments the temperature was varied from 250 to 700°°C. EXPERIMENTAL Preparation of Chalcocite (Cu2S) Natural chalcocite is not pure. Minerals such as bornite, covellite, and chalcopyrite may be present. It was decided, therefore, to prepare some chalcocite in our own laboratory. An intimate mixture of sulphur and finely divided metallic copper in the ratio of 4 g of copper to I g of sulphur was prepared. To this was added a slight excess of

Jan 1, 1948

By J. J. Pye, J. B. Drew

The surface-diffusion coefficients of Ni63 diffusing on low-index planes of nickel single crystals have been measured over the temperature range from 400° to 1000°C using a precision autoradio-gvaphic technique. The activation energy for sur -face diffusion appears to he the same on the {111}, {110), and (100) planes and amounts to -0.60 ev. This is in good agreement with the value (-0.62 ev) reported for (111) planes obtained by mass-transport techniques. In an earlier paper, the authors have reported self surface-diffusion coefficients on silver.&apos; In that work, a deviation of the diffusion coefficients from linearity in the Arrhenius plot was observed at high temperatures. This effect was attributed to a loss of tracer atoms into the bulk by volume diffusion. The purpose of the present work was to extend the technique developed to the nickel surface-diffusion system up to the point where volume diffusion would come into play. The nickel system especially lends itself to this technique due to the high efficiency of the isotope in darkening the film and the large absorption of the weak radiation (0.063 mev /3- particle of the trapped tracer atoms. The diffusion coefficients and ictivation energy for different orientations on nickel can also be compared with a report published by Blakely and Mykura 2 where a mass-transfer technique was used. This paper reports the self surface diffusion of nickel on the low-index planes over a wide temperature range using a precision autoradiographic technique. EXPERIMENTAL PROCEDURE The experiment is similar to that described in the earlier publication consisting of a radioactive needle as a source resting on a flat, smooth, chemically polished surface annealed in a dynamic dry-hydrogen atmosphere. The needle is held snugly on the surface by a holder fabricated from commercially pure nickel. The point source is made by grinding down a small-diameter nickel rod until a tip of approximately 0.1 mm radius is formed. It is then etched and the needle tip plated with the radioactive isotope Ni63. Nickel single crystals were used whose main impurities were spectrographically determined as Co 0.05, Fe 0.007, C 0.005, and S 0.003 pct. The surfaces, oriented to within 1/2 deg of the low-index planes, were carefully mechanically polished and etched in a 50-30-10-10 hot solution of acetic, nitric, sulfuric, and phosphoric acids giving a smooth polished surface. The crystals were then washed in distilled water and alcohol. Annealing temperatures ranged from 400° to 1000°C with a furnace arrangement in which the crystals could be brought up to temperature in times short compared to diffusing times. The temperature was maintained constant to ±10°C. In the temperature range investigated, the ratio of the surface-diffusion coefficient to the volume-diffusion coefficient (Ds/Du) was 105 or more and the mean bulk-penetration values, calculated from literature values of volume-diffusion coefficients,3 were on the order of 10-5 cm. After the diffusion anneal, the sintered needle is removed, and both the radius of the needle point and spot left on the crystal face are measured. The crystal is then placed on photographic film. Diffusion profiles are obtained by scanning the film with a recording microdensitometer which has a slit width of 10µ. DISCUSSION AND RESULTS The experimental conditions are such that the source strength and needle radius are essentially constant and the time is adjusted such that the mean bulk penetration is small. An exactly analogous heat-flow problem has been considered by Carslaw and Jaeger4 and the solution can be written in integral form as:

Jan 1, 1964

By C. D. Broadbent

INTRODUCTION The slope stability research plan at Kennecott was developed to serve the specific needs of large, open pit mines; primarily those developed in faulted and highly-fractured intrusive deposits. The program emphasis is on applied research; being defined in this case as research into the engineering mechanics of discontinuous rock and into the related rock property survey and slope design techniques. The program has been developed in phases, with each phase organized to explore more thoroughly the most significant findings of previous work and to improve on techniques found to be applicable. The current work is based on principles developed early in the program and that show promise of having engineering and economic value. A brief summary of the conceptual principles of the program is given to put our current work in context. This is followed by a review of the two cooperative programs done with the U. S. Bureau of Mines. Most recent work is described and interpreted in terms of practical slope design. Although failure-free slopes are a desirable goal, it is recognized that some failures will occur when overall slope designs approach a calculated safety factor of one. A discussion of failure control research is therefore offered. BACKGROUND In 1965 Kennecott management specified that a slope stability technology must be used to achieve optimum development of ore resources. The subject was carefully explored and by 1960 it had been established that there was no technology readily applicable to open pit slope design. Therefore, in 1962, Kennecott Copper Corporation and the U. S. Bureau of Mines agreed upon a cooperative research program having the objective of developing a mine slope stability science. One of the first decisions made by the cooperating groups was that the research must be conducted primarily in the field and not in the unrealistic environments of a laboratory. Accordingly, the Kimbley Pit, an abandoned mine once operated by Kennecott&apos;s Nevada Mines Division in Nevada, was selected for the full-scale research. Fortunately, there was near-universal agreement on the basic stability parameters and thus on the areas to be investigated. These parameters were acknowledged to be: (1) anisotropy (generally due to faults or joints), (2) stress, and (3) water; in that order of importance.

Jan 1, 1972

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.&apos;-4 Samsonov et al.&apos; reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami&apos;s Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By G. E. McElroy

MUCH attention has been directed to mine-air flow in recent years, more especially in Great Britian where there is frequent reference to a theory of fluid flow developed by English engineers. Briefly stated, this theory is that for similar passages of the same relative roughness, in which fluid flow occurs, the conditions of flow are exactly the same for equal values of the product W D V, where W = density of the fluid, D = diameter of the passage through which flow occurs, V = mean velocity of flow, and m = absolute viscosity of the fluid flowing. This, the "Reynolds Criterion" of fluid flow, had its origin in the work of Prof. Osborne Reynolds&apos; more than 40 years ago. Later, Lord Rayleigh amplified the theory2 which has been conclusively proved for small pipes by the experiments of Stanton and Pannel3 over a large flow range, and by Lacey4 over a somewhat more limited range. Concordant results on small pipes have also been obtained by numerous other investigators with single fluids over more or less limited ranges of flow. According to this theory results in one medium, such as water, are immediately applicable to another, such as air; and experimental results on models are (theoretically, at least) applicable to full-scale designs. This is of great importance in aeronautics and can be of considerable value in mine ventilation research. Hodgson, in a recent paper,5 has outlined the application of this theory to mine-air flow and recent English experiments&apos; on the resistance of a timbered mine airway have been expressed in this form.

Jan 10, 1926

By J. Campbell

The hydrostatic tensions in pure metals and long freezing range alloys are evaluated theoretically considering the viscous flow of residual liquid and the general plastic collapse of the casting. The former mechanism operates until the radii of the remaining liquid channels are of the order of 10-3 cm radius, after which the second process limits the attainable negative pressures which range from —1500 to -4200 atm for nickel, aluminum, copper, and iron. In previous reports1&apos;2 the maximum possible hydrostatic tensions developed during solidification have been evaluated employing spherical symmetry. This inevitably involves the concept of totally confined liquid regions, the reality of which has recently been brought into serious doubt3 following observations of the freezing of various transparent materials. Regions of interdendritic liquid which are apparently about to be isolated by the growth of dendrite arms are observed not to be cut off because the advance of the dendrite tips is arrested until the region has completely solidified. Although this may be the result of the very low melting point liquid available at this late stage in freezing, or the result of a higher rate of heat transfer to the dendrite tips because of the acceleration in liquid flow rate near the completion of solidification, this point need not concern us. In this paper an attempt is made to approximate more closely to real conditions; thus the assumption of confined liquid regions is abandoned and cylindrical symmetry adopted. It has also been necessary, therefore, to consider the viscous flow of residual liquid through the remaining channels in the pasty zone. Furthermore, the rather special conditions of spherically symmetric solidification led to extremely high solidification rates and hence unusually high tensile stresses as solidification neared completion; the cylindrical Symmetry appears to yield solidification rates and stresses which are more typical of real castings. The rate of solidification is first considered since this critically affects both the flow of the liquid and the creep of the solid.

Jan 1, 1969

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By L. R. Jackson

It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses This system can be resolved into a new system consisting of the three components and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation _ Sm Tr = Sm - Sm is given by Eq. I and Sl is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. Table i.—Triaxid Ratios for Various CommonSyslems Triaxial Ratio Stress System Tr Hydrostatic compression — SI - —St - -S³............................... -1 Torsion or shear -SI - S². S² = O..... O Simple tension SI. SI = SI = 0......... +0.33 Biaxial tension SI = S² S³ - 0......... +0.66 Hydrostatic tension +SI - +S³ = +S³. +1.00 Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1945