Search Documents

By A. A. Bauer, F. A. Rough, G. H. Beatty

AS a result of recent studies, the constitution of the zirconium-uranium system has been fairly well defined. A diagram for the system is shown in Fig. 1. However, both oxygen and nitrogen are known1-3 to have a pronounced effect on the limits of both ß- and e -phase regions. It has been shown that small amounts of oxygen severely constrict the compositional limits of these phase regions in the ternary zirconium-uranium-oxygen system. A previously published tentative diagram shown in Fig. 2 illustrates the ß-phase constriction resulting from oxygen additions. Generally, iodide zirconium has been used in constitutional studies of zirconium-uranium alloys. While this is the highest purity material available, cast iodide zirconium-uranium alloys will generally average from 200 to 300 ppm 0 and from 50 to 60 ppm N. Thus, while the constitution of the zirconium-uranium system is fairly well defined, it must be realized that this definition applies to alloys containing in the vicinity of 250 ppm 0 and 50 ppm N. The present investigation was undertaken to accurately determine the boundary between the ß-plus-P and ß phases at a single temperature in the binary zirconium-uranium system by quantitatively

Jan 1, 1959

By C. E. Reistle

All crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms. Factors That Control the Solubility of Paraffin in Crude Oil Two main factors, possibly three, govern the solubility of wax in crude oil. The first of these is temperature. The solubility of wax in crude oil increases with an increase in temperature, and as the temperature approaches the melting point, the wax becomes soluble in all proportions in the crude oil. The higher the melting point of a wax, the less soluble it is in crude oil below its melting point. All crude oils containing wax can be chilled to a point where the oil is saturated with wax. If the temperature is decreased below this point, some of the wax will crystallize from solution. Fig. 1 shows the effect of temperature on the solubility of crude paraffin in oil. The second factor is the amount of volatile constituents and gas removed from the crude oil. Evaporation of the volatile constituents and gas lessens the volume of the oil and concentrates the solution of wax in the oil; therefore less wax can be held in solution at a definite temperature. As the natural amount of wax present in the oil is constant, this results in the oil becoming saturated with wax at a higher temperature than if the volatile constituents and gas were still in the oil. As an example of this, a fresh sample of crude oil having a gravity of 39.8

Jan 1, 1928

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

By E. S. Machlin, S. Weing

GRAIN boundary stress relaxation has been the subject of several investigations in recent years, but as yet the phenomenon is not well understood. One of the major difficulties has been the lack of a sufficient amount of data with which to evaluate any proposed mechanism. Little information is available on the effect of small amounts of substitutional solutes on grain boundary stress relaxation. It is with this important phase of the problem that this investigation is concerned. The influence of substitutional solutes on grain boundary stress relaxation has been recently investigated in copper by Pearson: and in aluminum by Dorn et al.' Pearson studied the effect of zinc, gallium, germanium, and arsenic on the relaxation peak of OFHC copper.* The pure OFHC copper decreased the peak intensity and a second peak appeared at a higher temperature. This latter peak was termed the alloy grain boundary peak. At the lowest binary concentration studied, approximately 1 atomic pct, the primary peak was almost completely obliterated. Pearson found that the activation energy calculated from the alloy grain boundary peak for all solutes, irrespective of the concentration, was 44,000 cal per mol. Pearson concluded that the increase in activation energy from 33 to 44 kcal per mol is not continuous but abruptly changes from the lower to the higher value. As no attempt was made to investigate the intermediate range of concentration and hence calculate the possible variation of the activation energy for the initial grain boundary peak, this conclusion is hardly valid. In contrast to these results, Dorn et al. studied the effect of zinc, silver, copper, germanium, and magnesium on the grain boundary stress relaxation of aluminum. No change in the energy of activation was observed for binary alloys of the flrst four solutes, but a linear increase was found for increasing concentration of magnesium. Saturation was not found up to the maximum of 1.6 atomic pct. The energies of activation were obtained by plotting the horizontal displacement of the dynamic modulus curve vs temperature for two vibrational frequencies. As the modulus is proportional to the square of the frequency, this requires the measurement of the torsional frequency over a range of temperature. However, the technique does not lead to an unambiguous interpretation of the grain boundary

Jan 1, 1958

By Calvin Pierson, R. S. Dean, E. P. Barrett

MANY studies have been made of the properties of steel produced by adding varying amounts of sponge iron to the charges used in steelmaking furnaces.1-3 The results of these previous studies, however, have failed to disclose a reason for the belief of steelmakers that steel made in this way is definitely different from steel made entirely from scrap or iron melting stock. This paper deals chiefly with the structure of the sponge iron, of the wrought iron made by welding the sponge iron into blooms, and of the steel made by melting the forged and rolled blooms. It is believed that the structure of the final steel is inherited from the ore and that this inherited structure produces marked differences in the properties of the steel and explains the feeling of steelmakers which is based on their experience. Three kinds of sponge iron were used in this investigation: One made from a limonite ore reduced with natural gas, one made from a hematite ore reduced with natural gas, and one made from a magnetite ore reduced with charcoal. The sponge iron made by reduction with natural gas

Jan 1, 1935

By John C. Loretta

INTRODUCTION Organizations that regularly use project management services will almost certainly have their own views on the preferred systems and procedures. This chapter, therefore, describes Project Management for the personnel of groups not familiar on a regular basis with project management and deals with the basic questions that these groups can be expected to ask, such as: - What is project management? - Why is it needed? Project Management is the planning, implementation and monitoring of the Engineering, Procurement and Construction activities that are necessary to complete the project in the most economic manner. In the case of a crushing and grinding plant, completing the project would mean bringing it into full operat ion. Engineering is the design work for the purpose of producing drawings and technical specifications for Construction together with technical specifications and quantities for Procurement. Procurement is the arranging of con- tracts so that equipment, material and labour are brought as required to the construction site. Construction covers the on-site activities that bring together the components of Engineering and Procurement so as to arrive at a finished plant. Need & Cost Benefits Project Management systems are needed to allow progress and expenditures to be monitored so that any significant deviations from the plan can be identified and the appropriate corrective action taken. In this way, Project Management is able to give continual updated answers to the Owners broad questions. - What am I getting? - What will it cost? - When will it be ready? The need for Project Management is not always immediately apparent, a common belief being that the existence of the three components -Mining Company - Equipment Supplier - Construction Company - is sufficient to get the job done without a formal project management group. This trio

Jan 1, 1982

By Joseph Moses Botbol

This study was designed to demonstrate the viability of using high-frequency radio transmission as a means of communications between a remote field camp and a time- sharing computer system. A field camp near Johnstown, Pa., was linked by high- frequency radio to a base station 160 miles to the southeast in Vienna, Va. The base station was in turn linked by telephone to a time-sharing computer system near Los Angeles, Cal. Error-free data transmission utilized highly stable receivers and transmitters, forward error correction, and dual-frequency diversity. Three geologic applications programs resident in the Los Angeles computer were executed from a graphics cathode ray tube terminal in the field. Bulk data equivalent in volume to 4 days of typical spectrographic analytical work generated by one spectrograph and one spectrophotometer were transmitted from the field to the base station. All programs, were executed successfully, and all data were transmitted error free.

Jan 1, 1976

By C. W. Spencer, J. Singer

A PARTIAL phase diagram for the As-Te system is given in Hansen.' The only compound reported is As2Te3, melting at 362°C. Stoichiometric quantities of reagent-grade elements were reacted in evacuated quartz and directionally cooled. The resulting ingot consisted of very thin threadlike crystals from which only very small single-crystal fragments were isolated. A powder diffraction diagram disclosed nonisomorphism with the analogous V-VI compounds insofar as these have been reported; Sb2S3, As2S3, Bi,S,, and Bi2Te3 data in the ASTM index of powder patterns, together with the single-crystal data on Sb2Se3,2 were used for the com- parison with the observed spacings. Single-crystal data confirmed the uniqueness of the As2Te3 structure. Single-crystal Weissenberg diagrams have so far yielded the following data: As2Te3 is monoclinic, space group C-m (OkO data still lacking), a = 14.4A, b = 4.05A, C = 9.92A, ß = 97". The cell volume is about 5802. The set of isomorphous ortho-rhombic cells of Sb2Se3, Sb2S3, and Bi2S, are apparently related to As,Te, in having one lattice constant close to 4.0 and with cell volumes as large as 540A8. Assuming Z = 4 for As2Te3 also, the density is calculated as 6.1 which agrees well with a roughly determined value of 6.0. A complete structure analysis is under way.

Jan 1, 1956

By John Wulff, J. H. Hollomon

THE opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was redeposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufficiently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion.4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May,6 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to alpha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. They believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They did not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,8 in another publication, suggested that the commonly found gray or black arsenical film may act to: (I) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led him to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed during the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (As203),

Jan 1, 1942

By H. F. Hebley

In recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and cleaning of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal. Illustrative of this condition is a table of ash contents for the various petrographic constituents of Illinois coal (No. 5 bed) as given by Mitchell' (Table 1).

Jan 1, 1934

By Nicholas J. Grant, Yoichi Ishida, Arthur W. Mullendore

An inert particle -marker technique was developed to provide a direct measurement of grain boundary sliding during creep in tile interior of aluminum specimens. Groin boundary sliding in the interior as measured by this technique was found to be nearly the same or slightly lower than that measured on the surface. These data disagree with those obtained by the grain-counting technique developed by W. A. Rachinger. In tests where both techniques were used, the grain-counting technique gave large and variable values of grain boundary sliding. It is shown that the grain-counting technique gines erroneozcs results because of a preferred direction of grain growth during creep. A question which has long plagued those who study grain boundary creep is whether or not surface measurements yield a true representation of the deformation in the interior of a specimen. The first attempt to measure grain boundary sliding in the interior of a creep specimen was made by Rachinger.1 His technique is based on the measurement of average grain diameters, both parallel and perpendicular to the tension axis, followed by a calculation of the grain elongation from these measurements. The difference between total elongation, Et, and the calculated grain elongation, Eg, is considered to be the result of grain boundary sliding, Egb. Surprisingly large values of Egb/ Et (90 pct) came out of creep tests of pure aluminum at temperatures above 250°C (480°F), utilizing the Rachinger technique. This value is very much larger than the values of 8 to 15 pct measured by numerous investigators on the surface of a specimen. Values obtained on the surface by Rachinger, however, were consistent with those measured by the displacement of reference scratches. Chaudhuri and Grant2 repeated the Rachinger method for A1-10 pct Zn, and found the same large values of Egb/Et inside the specimen. However, from purely geometrical considerations, grain boundaries cannot slide without grain deformation; therefore, they questioned the validity of Rachinger's grain-counting method. Several authors2,3 have suggested that grain boundary migration during high-temperature deforma- tion may tend to restore the equiaxed grain shape in order to minimize interfacial energy. Rachinger4 tested this hypothesis and found that it did not hold. Grains elongated by rapid extension retained their elongated shape during a subsequent slow creep test. It appears that some other factor was responsible for the abnormally high values of .Egb/El. McLean and Gifkins5 made a survey of the effect of grain size on the ratio Egb/ Et, and proposed that the high values were the consequence of a small grain size. They failed to explain the low value of Egb/Et which Rachinger observed on the surface of the small grain size specimens, and suggested that the surface effect on the value of Egb/Et does not always occur. Many of the disagreements arising from Rachinger' s work stem from the fact that there was only one method of estimating grain boundary sliding in the interior of a specimen, and that method was of an indirect nature. If a marker line of some sort could be introduced inside of the specimen, one could make measurements just as clearly as on the surface. In the present investigation, the technique utilizes a layer of finely dispersed oxide particles inside the specimen introduced by hot press-bonding of two pieces of aluminum. Rachinger attempted a similar technique but with the oxide distribution he obtained there was so much interference with grain boundary motion that quantitative measurements were not attempted. MATERIALS AND EXPERIMENTAL PROCEDURE A) Materials Preparation. Two pure aluminum rods (impurity content in percent: Si, 0.002; Cu, 0.004; Fe, 0.002; Mg, 0.000: Zn, 0.000; V. 0.001) 1 in. diameter by 2 in. high were jacketed end to end in a 4-in.-diam cylinder of commercial-purity aluminum, 4 in, high, which had a l-in.-diam hole. The l-in.-diam mating surfaces of the two pure aluminum rods had been electropolished initially. This interface provided the oxide-film internal -marker plane after the hot press-bonding process, see Fig. 2. The composite was annealed for 1 hr at 900 F and hot upset more than 50 pct reduction in height in one step. The resulting slab was then rolled to 1/2 in. thickness; the pure aluminum test material was cut out and annealed at 900°F for 1 hr and cold cross-rolled to 1/8 in. thickness. The sheet was machined into specimens with a 1/8-in.-square cross section and a 1/2-in. gage length. The following heat treatment was given the specimens: Specimen 5A series: annealed at 1000°F for 5 min for grain-size control and then cooled to 700°F and held for 15 hr for stabilization.

Jan 1, 1965

By A. F. Melcher

The present paper is a progress report on an investigation of the physical factors of oil and gas and especially of their sands,' such as pore space, size of pores or permeability, retentivity, viscosity of the oil, temperature, pressure, thickness and area of the pay sand, water relations, and capillarity. The purpose is to determine as many of these physical factors as possible, and to ascertain the relations existing, directly or indirectly, between these physical factors and the production of oil and gas. As yet only pore space2 and size of grains of pay sands have been investigated, although an apparatus has been designed to determine the permeability of a sand to oil, water, or gas under definite drops of pressure between the entrance face and exit face of the sample. Messrs. E. W. Shaw, R. Van A. Mills, D. Dale Condit, G. B. Richardson, G. C. Matson, and C. H. Wegemann collected the samples upon which the physical determinations were made. Acknowledgment is made to my colleagues of the United States Geological Survey for many suggestions and criticisms; to Mr. Mills for the production data given of the oil wells from which some of the samples were collected; to Mr. A. W. McCoy of the Empire Gas and Fuel Co., Bartlesville, Okla., for many ideas. Determining Pore Space of Oil and Gas Sands In selecting a method for the determination of pore space, two objects were kept in mind: First, the method must not only be sufficiently

Jan 1, 1921

By H. W. Morse

The experimental work on the oxidized copper ore at the New Cornelia mine at Ajo, Ariz., ended on Jan. 12, 1916. On that date final decision was made on the general nature of the process to be used in the 5,000-ton leaching plant, and on many of the details, as far as experience on a 40-ton scale could decide them. With the approval of the Board of Directors and the General Manager, John C. Greenway, we have compiled what seem to be the most interesting data on the results obtained during the experimental period. The most important part of the data resulted from the operation of a 1-ton and a 40-ton plant at Ajo. Experimental work on Cornelia oxidized ore dates back to April, 1912, and has been going on nearly continuously since that time. A good many variations from the original idea have been tried, but the process finally decided upon is in principle and in all of its details a simple one. The history of the leaching work on this ore has been brought down to about a year ago in papers presented to this Institute by Stuart Croasdalel and Dr. L. D. Ricketts.2 The present paper will, therefore, deal principally with the results obtained during the last year of the work. Preliminary Tests by Mb. Croasdale Preliminary tests were begun by Stuart Croasdale in July, 1912. A number of important points were definitely decided by his work. Among these were: 1. New Cornelia oxidized ore, not very finely crushed (to about 2-to 3-mesh) showed good extraction with 5 per cent. sulphuric acid. It appeared that better than 80 per cent. extraction could be expected. 2. The consumption of acid for this extraction was not prohibitive. It was apparently 3.5 to 4 1b. gross per pound of copper recovered.

Jan 1, 1917

By W. A. Backofen, B. C. Wonsiewicz

The Plasticity transition in magnesium was studied by plane-strain compression of single crystals and polycrystalline material at temperatures from about 20" to 307°C. Reduction of single crystals along the c axis was accommodated by twinning on {1011) and retwinning on (10 12}, followed by basal shear in the doubly twinned volume. Deformation in that mode can result in sufficient independent shears for arbitrary shape change. Fracture in c axis compression, below about 100°C, has been related to excessive shear caused by unloading from the stress for {1011} twinning (-50 ksi at 20°C) to that for slip within the twin (-3 ksi); ductility follows from heating because the stress difference is lowered and the twin volume, in which elastic strain energy is dissipated on unloading, is increased. The stress for (1011) twinning is strongly temperature-dependent but not given by a critical resolved shear stress law. The latter is attributed to the influence of stress concentration from prior intersecting shear on nonbasal planes, the former to the temperature dependence of the preliminary slip. THE basic symmetry of hcp crystals has the effect of limiting the number of independent slip systems and making twinning an important deformation mechanism. The general result in wrought polycrystalline aggregates is a more or less sharply developed texture (or preferred orientation) which underlies a strong anisotropy in mechanical behavior. Knowing how the one influences the other is essential background for the use of such materials. Magnesium was of interest in this work because of the unexplained plasticity transition that it undergoes somewhere in the neighborhood of 200°c.''~ At lower temperatures plastic deformation before fracture in polycrystalline material is limited, while at higher temperatures extensive deformation is possible. The transition temperature commonly determines the lower limit of the range in which magnesium is worked. The limited ductility can be traced to a lack of independent crystallographic shears. A minimum of five are required for arbitrary shape change.' Around room temperature, however, slip on all known systems provides only four.' In each case, the slip direction is in the (0001) basal plane so that slip does not allow strain along the c axis. With increasing temperature, more slip occurs on the ( 1011) pyramidal plane and the ( 1010) prism plane but without change in direction.'?' Thus, that development alone cannot explain the transition temperature.

Jan 1, 1968

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core.

Jan 7, 1951

By R. Woods

INTRODUCTION Gaudin (1), considered that "the mechanism of mineral collection is the central problem of flotation theory". From their work on adsorption phenomena in flotation for more than fifty years (2), Gaudin and his co-workers have made major contributions to the elucidation of this mechanism, a fact acknowledged by their contemporaries in the field (e.g. (3)). Their investigations in a number of areas, e. g. demonstrating that submonolayer quantities of adsorbed collector species can induce flotation, or identifying the influence of substances which can activate or depress (1), have helped to provide the basis for and the development of a theory to account for the interaction between mineral and collector. It was established in the late fifties (4) that the presence of oxygen is a prerequisite for the flotation of metal sulfides with thiol collectors. This fact rendered inadequate the concept of simple ion adsorption being responsible for rendering these minerals hydrophobic. The requirement for oxygen has been explained (1) in terms of this species being a component in chemical reactions between the sulfide surface and the collector. Gaudin has been instrumental in identifying the products of chemical reactions at sulfide minerals (1, 5), a line of work which has been continued particularly by Finkelstein and co-workers in South Africa (6). In presenting a detailed mechanism of the mineral-collector- oxygen interaction, it has often been considered that the mineral surface [must] first be oxidized to a metal oxy-sulfur species which

Jan 1, 1976

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

HEAT-RESISTANT alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:12 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to 1.o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage II) of one per cent in ten thousand hours as extrapolated from rates per hour or tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at 1800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,1 in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably dose, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By W. Kennedy

THROUGHOUT northeastern Texas we have an extensive series of iron-ore deposits, occupying portions of nineteen counties and having approximately an actual ore-covered area of 1000 square miles. The existence of these ores has long been known. Kennedy* says: "Iron-ore is distributed in profusion throughout Texas, being found almost everywhere except in the level region of the coast." Before this, C. Newell† had mentioned the existence of these ores thus: " Iron is found in abundance in the eastern, northern and middle portions of Texas;" and in 1849 Edward Smith‡ said: " We met with immense hills of iron which were said to be, and appeared to be, of excellent quality, in Cass and Titus counties.. . .. It is well known that Texas abounds with iron of first-rate quality." In 1859, Dr. Shumard? reports that detailed surveys had been made in several counties, and says: " Our labors have demonstrated the important fact that we have a vast iron-region in the eastern part of the state, embracing considerable areas in Cass, Harrison, Rusk, Panola, Smith, San Augustine and Shelby counties. The ore-deposits belong to the Tertiary era and consist chiefly of hematites and limonites, of which there are several varieties. We have also found in this district extensive beds of carbonate of iron." Dr. Shumard gives no very exaggerated description of Cass county§ as it then existed when he says : " Cass county alone is capable of supplying a number of furnaces with an abundance of excellent iron-ore for many years." Of Rusk county he says: "Our de-

Jan 1, 1895