Search Documents

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By C. O. Burgess, W. D. Forgeng

DESPITE the increasing interest in and the technical importance of iron-chromium-manganese alloys, very little published information is available regarding their constitution. F. M. Becket's paper1 in 1930 represents the first correlated effort in the field of these alloys. The paper served particularly to draw attention to the commercial possibilities of iron-rich alloys containing chromium and manganese in balanced proportions. The duplex structure of alloys within the commercial range was briefly discussed, but exposition of their structural constitution was necessarily limited because the physical properties and corrosion resistance of the alloys were the main subjects of the paper. Both prior to and following the publication of F. M. Becket's paper, and at his instigation, an extensive investigation of the constitution of iron-chromium-manganese alloys of commercial purity was in progress at the Union Carbide and Carbon Research Laboratories, Inc. The present paper is based on the results of that investigation. In the last few years, investigations covering various portions of this alloy system have also been made in Europe. W. Koester briefly mentioned the effect of annealing on chromium-manganese steel2 and later3 constructed approximate sections of the iron-chromium-manganese equilibrium diagram. M. Schmidt and H. Legat14 even more recently studied this system, and their article and conclusions are of interest as representing an entirely independent study of a number of iron-chromium-manganese alloys. Koester's sections are shown in Fig. 1. The figures summarize the effect of manganese additions to iron alloys containing 5, 10, 15 and 20 per cent Cr as well as the effect of increasing chromium content on iron alloys containing 3, 8, 20 and 30 per cent Mn. These diagrams, within their composition limits, substantiated in some measure the results of our investigation. However, in our work some differences as regards the position of the mixed alpha-gamma fields were found as compared to Koester's work, and we were able to detect the presence of

Jan 1, 1938

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing acid shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subse-quently mineralized by sulphides and barite.

Jan 1, 1937

By T. L. Joseph

THE invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.1 After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it. His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be encountered from oxidation of the iron. Mushet was not only an inventor but he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, arid he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 5, 1927

Note Any member who desires to be designated as being "Available for Consulting Work" can arrange it simply by sending a written request to the office of the Secretary of the Institute The following list of members is primarily arranged geographically, with secondary consideration to political subdivisions arranged alphabetically First, the states of the United States , then other North America, in order Alaska, Canada, Mexico, the West Indies, and Central America Then cones South America, Europe, Africa, and Asia, each including the near by islands associated with those continents Australia, the islands to the north, and the Pacific islands except Japan are grouped together under Oceania The various countries are indexed on the preceding page NORTH AMERICA UNITED STATES ALABAMA America -Dyar, G C Anniston -DePriest, S H Klugh, B G Lefforge, J W Auburn Poor, R S Bankhead -Armstrong, W D Bessemer -Beck, A IV, Jr Carnes, D Chabot, L S , Jr Creveling, J C

Jan 1, 1952

By H. I. Aaronson, H. A. Domian

ELectvon-probe analgsis has been used to in7:estigatr the partition ot alloying- elements between aus-tenite and proeutectoid ferrite (or the Jerritic component of bainite) in high-purity Fe-C-X alloys, lsuully at tzco levels of carbon content fca 0.1 and 0.4 pct in ntost steels) at temperatures between the M, and the Ae3 in Si, mn, Ni, mo, Co, Al, Cr, Cu, and PI steels. No partition ous found during the early stages of transformation at any temperature studied in the Si, ,mo. Co, Al, Cr, and Cu steels. Partition did take place, Jrowel'er, in Ihe Mn, ATi, and Pt steels, occurring in lewtperature. regions below the Ae3 of ca 130°, 65", UNDERSTANDING the mechanisms through which alloying elements influence the kinetics of austenite decomposition reactions which proceed by nucleation and 35c respectively. A break was discovered in the TTT curve for the initiation oj the proeutectoid ferrite reaction in the latter steels at the temperature at which partition began. The alloy content in ferrite at the a:y bondavy remained at constart lecels, shown experimentally to be significantly above those corresponding to eqiilib+iu??l, e'en at the longest reaction times investigated (ca 1o6sec). The partition and the TTT curve observations foere rationalized on the basis of the thermodynamic treatment developed in an accompany ing paper. and diffusional growth has been a major research objective of physical metallurgy since the latter part of the 19th century. The measurements made on the dif-fusivities of carbon and of substitutional alloying elements in austenite during the 1930's and 1940's seemed to provide a useful clue as to the nature of these mechanisms. These measurements showed that the diffu-sivity of carbon is several orders of magnitude higher than that of the alloying elements at a given tempera-

Jan 1, 1967

By A. C. JR. Boyle

I. INTRODUCTION THE geological field work of the Bully Hill district, upon which this paper is based, was begun July 1, 1908, and covered a period of three months. The time was found too short for a complete report and the district was again visited in the early part of July, 1912,. from which time detailed study of the locality continued until September of the same year. This paper is the result of observations made in the mines in the immediate vicinity of Winthrop, Shasta county, Cal., during these two periods of study. The preparation of this report has been greatly facilitated by various courtesies rendered the writer by D. M. Riordan, President of the Bully Hill Copper Mining & Smelting Co., and by John B. Keating and Herbert R. Hanley, managing officers actively in charge at the mines. The elaboration and further study of the notes and collections were carried on in the laboratories of the Departments of Geology and Mining at Columbia University, and the writer takes pleasure also at this point in expressing his acknowledgments to Profs. James F. Kemp, A. W. Grabau, Charles P. Berkey, and William Campbell, for advice and assistance. In order that one may appreciate at first reading the significance of some of the details which follow, and for the sake of clearness, a brief outline of the geological relationships is here given, together with certain conclusions which have been reached regarding the genesis. of the ores and the gypsum masses. In the Bully Hill mining district an associated series of Triassic lavas and tuffs, chiefly andesites, is preceded as well as followed by sediments. The entire system is tilted so that the original bedding planes dip in general to the southeast. The surrounding region has been greatly disturbed, and in the immediate vicinity of the mines close folding of the later sediments and extreme shearing of the igneous rocks locally is a striking feature. Into the nearly vertical shear zones have been intruded post-Triassic dikes of various rock types in the following order: alaskite-porphyry and andesite-porphyry. Outside the area under consideration diorite dikes are known, but they will not receive attention further than to note that' they, probably, represent a differentiation product of the same magma from which the other two dikes came. In this connection all the dikes have an important bearing on the origin of the ores and of the gypsum found in the mines.

Jan 1, 1914

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleysl and Gathmann,2 who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1951

By Dudley Homer

MINAS DE MATAHAMBRE, S.A. is a Cuban mining corporation with mines located in the Matahambre district about 100 miles westerly from Havana in the Province of Pinar del Rio. The port of entry is the subport of Santa Lucia on the north coast of Cuba. The mines are located six miles inland at the town of Minas de Matahambre. Minas de Matahambre and Santa Lucia are connected by a 9-mile automobile road, and a 30,000-ft. Leschen aerial tramway. At the subport of Santa Lucia the company maintains docks, concentrate bins, tugs, lighters, and miscellaneous shipping equipment. The power plant of the company is also located at Santa Lucia. Connection between the power plant and the mine is effected by a 30,000-ft. transmission line. In the town of Minas de Matahambre are located the mines, concentrator, shops, and warehouses. The con-centrates are transported to Santa Lucia by the Leschen aerial tramway. The mines are equipped with three shafts, viz., Nos. 1, 2, and 3. (Fig. 1.) No. 1 Shaft is a three-compartment vertical tim-bered shaft and has reached a depth of 1825 ft. This is the present main hoisting shaft. No. 2 Shaft is a four-compartment vertical shaft lined with steel sets and native hardwood lagging. Certain portions where the ground is heavy have been lined with re-inforced concrete. Practically all production will be hoisted eventually through this shaft. No. 3 Shaft is a three-compartment vertical timbered shaft. It has reached a depth of 1090 ft. Its purpose is for prospecting, ventilation, and handling men and sup-plies through the north section of the mine.

Jan 1, 1933

By Dwight K. Smith, Greg Carter

Studies have been conducted on The properties of many deep well cementing compositions to determine their Strength behavior over curing periods to 180 days at elevated tem-peratures and 3,000 psi pressure. This pressure results in essentially the .vat, compressive strength as that obtained with much higher pressures in ac-cordance with the findings of an API subcommittee ' These different compositions include API C1asses A, E, and F cements containig additives such as retarders, berrtorlite, heavy weight materials and pozzolans. All compositions except mixtures of Poz-zolrrrts and hydrated lime show from mild to severe degrees of strength lass over a temperature rang from -730 to 320" F after setting. Pozzolatl-time compositions actually gain in strength with time at these high temperatures. Other chemical find physical properties evaluated to observe their inter-relation.ship with Strength loss show very little correlation except in per-meability. As retrogression in strength increases, the permeability of set cement increases. X-ray difraction patterns on the set products indicate the formation of certain compounds having little or no strength value in those cementing compositions where strength loss was more severe. INTRODUCTION As a result of the growing trend toward deep well completions, a study has been made on the properties of the various cementing slurries presently in use at elevated temperatures and pressure. The strength of these compositions is of prime importance in selecting the most suitable material for use at high temperatures, to determine WOC time and the proper time to perforate with a minimum of shattering. Of primary interest in this investigation was the strength behavior of various compositions currently in use, and the effect of additives on cement after long periods of curing under severe conditions. Earlier investigators have pointed out that the strength of some cements will increase with increasing curing temperature to about 220 to 340" F, but at higher temperatures a loss in strength occurs at extended time intervals. Studies by the API Mid-Continent District Study Committee on Oil Well Cements' outlined a testing procedure whereby field conditions of temperature and pressure could be simulated in the laboratory.' It was observed that retarded cements undergo changes at elevated temperatures and some lose as much as 50 per cent of their early strength when cured at high temperatures. The scope of these tests was limited to curing periods of 1 to 28 days; additives were not covered in this study. Saunders and Walker' found that the use of additives influenced the strength behavior of cements at high temperatures, but studies were conducted only to a seven-day curing period. Ludwig and Pence' conducted an investigation of two types of cements under elevated pressures and temperatures in an effort to explain the causes of this loss in strength phenomenon. It was observed that with retrogression in strength there were other physical and chemical changes which took place as the cement aged. Today there are a number of cementing compositions available for use at well depths below 10,000 ft. Since all these earlier investigations were limited in curing time as well as the number and type of compositions studied, it was believed that a more extensive study should be conducted on the properties of cements at elevated temperatures, and this work should include those compositions actually in general field use at this time.

By William G. Christy

EFFORTS at smoke abatement date back to the year 1273 in England when a law was passed prohibiting the use of "sea cole." The law was not enforced, so King Edward I, 33 years later, appointed a commission "to enquire of all such who burnt sea cole in the city or parts adjoining, and to punish them for first offense with great fines and ransomes, and for the second offense to demolish their furnaces." Many other commissions have since been named to investigate the smoke problem in England, but it still persists in many British cities. In the United States the movement to abate the smoke nuisance started in certain Middle Western cities, and has made considerable progress. Until recently, the coal-producing industry co-operated little in smoke¬abatement programs, taking the attitude that smoke elimination is the dealer's or user's responsibility; and the dealers, in turn placed the responsibility entirely on the user.

Jan 1, 1942

LIMA (PERU) Established May, 1952 (Official year begins in June) Luncheon meetings third Wednesday monthly Ernesto A Baertl, Chairman Arthur C Hall, Chairman-elect Raymond R Beard, 1st Vice-Chairman Edgardo Portaro, 2nd Vice-Chairman Walter E King, Secretary-Treasurer Av Santa Cruz 331 San Isidro, Lima, Peru Alberto E Brazzini, Asst Treasurer Daniel M Rodriguez, Asst Secretary Robert P Koenig, '56, Section Delegate Arthur C Hall, Alternate Section Delegate

Jan 1, 1955

[ ]

Jan 1, 1938

By S. L. Hoyt

IN technological studies on steel considerable emphasis has been placed on the identification of the foreign inclusions, testimony of which is adequately given in the metallographic literature covering methods for their identification. The outstanding accomplishment in this field is the scheme devised by Campbell, Comstock and Wohrman for identi-fying various oxides, sulfides, silicates and other constituents by syste-matic etching tests and microscopic examination.1 The time involved in carrying out this procedure has led to attempts to secure quicker methods, or at least to shorten the time required to secure essential information. An example of this is the use of dark field illumination, but when this was tried out by the authors it was found that cavities and pits on the polished surface appeared bright on a dark field and could not be distinguished from small glassy inclusions. Still another means is the Leitz Ultropak, an instrument equipped with optical units for the illumination of the specimen by reflected light to secure an effect similar to dark field illumination. The structures are made visible in exceedingly sharp details by utilizing the inherent properties of the samples, such as refractive index, absorption coefficients and reflection powers. We have had no experience, with the Ultropak, but a recent paper by Benedicks and Löfquist3 describes methods for

Jan 1, 1934

By AIME AIME

THE official opening at the 134th general meeting of the Institute was held on Oct. 6, but it was prefaced by two round table conferences on Oct. 5. The open-hearth group held the fourth of their semi-annual conferences at the William Penn Hotel, devoting the morning session to discussing a paper by R. L. Cain on the "Manufacture of Forging Steel by the Open-hearth Process," and the afternoon to discussing P. H. Shaeffer's paper on the open-hearth charge. At the Bureau of Mines, a round table conference on the combustibility of coke was held on Tuesday morning, and the afternoon was devoted to a similar conference on the testing of coke. The formal opening session of the meeting assembled in the Music Hall of Carnegie Institute at 10.30 a. m. Graham Bright, chairman of the Pittsburgh Section; called the meeting to order and presided. President Taylor welcomed the visiting members and guests to his home city and reviewed briefly the advancement of mining in the past half century during which, for ex- ample, the coal output had increased from 53,280,000 tons to 523,357,000 tons per year. He emphasized the important part Pennsylvania played in mining and brought out the principal changes that had taken place in methods. In part, his remarks were as follows: The centennial year, 1876, found the coal business of. this country, as a whole, producing 53,280,000 tons, of which amount the bituminous mines of this State yielded 24 per cent. In 1925, this country produced 523,357,000 tons of coal, of which Pennsylvania produced 24 per cent.

Jan 1, 1926

By Archer E. Wheeler, Milo W. Krejci

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until June 1, 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston & Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operation of and appliances for the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detaild accounts of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General. Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation. of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres. 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag, General Chronological Review. Ground was broken for the general concentrating and smelting plant in the spring of 1,891. The first departments to start operations were the concentrator in March, 1892, and the Brückner roasting and reverbera-tory smelting departments in April, 1892. The converter department

Jan 1, 1914

By V. N. Krivobok

THE study and use of low-carbon manganese steels have been curiously neglected in the general history of developments in alloy steels. Hadfield1 made an extensive study of manganese-iron-carbon alloys about 1886, which culminated in the wide application and use of Hadfield austenitic manganese steel. His alloys were nearly all high in carbon, as compared with the steels discussed in this paper, and he found a marked tendency towards brittleness in the alloys of medium and low manganese content, that is, below 7 per cent. manganese. As a result, there has been a widespread prejudice against the use of manganese steels containing between 1.0 to 3.5 per cent. manganese with comparatively low carbon. Steels of this composition have never been studied adequately in comparison with other alloy steels, and have had little use in practice. In a very recent paper by Sir Robert Hadfield2 the following statement appears: ?. . . manganese-iron alloys with little or no carbon do not seem to offer any practical employment; they only become valuable in the presence of quite high percentages of carbon, 0.90 to 1.50 per cent." The results of the present investigation are so contrary to the findings of Hadfield that the writers feel fully justified in presenting the preliminary report incorporated in this paper.

Jan 1, 1927

CONTENTS PAGE HESSE, A. W,-Safeguarding Coal-mining Operations against Danger from Oil and Gas Wells. Discussed by A. W. Hesse, T. G. Fear, George H. Ashley, George S. Rice, W. E. Fohl, R. V. Norris, S. A. Taylor, F. B. Tough, C. W. Gibbs, A. Hurlburt, S. W. Meals 1 DAWSON, THOS. W.-Belt Conveying of Coal at H. C. Frick Coke Company Mines. Discussed by F. F. Jorgensen, Thos. W. Dawson, Graham Bright, A. W. Hesse 13 OTTO, HENRY H.-Ultimate Recovery from Anthracite Coal Beds. Discussed by R. V. Norris, S. A. Taylor, Henry H. Otto, Douglas Bunting, Graham Bright, Howard N. Eavenson, J. B. Warriner 15 HOSLER, Rush N.-Schedule Rating Coal Mines in Pennsylvania for Compensation Insurance Rates. Discussed by E. A. Holbrook, W. W. Adams 17 ARCHBALD, HUGH.-Application of Gaussian Curve to Mining Industry. Discussed by Donald A. Laird, T. T. Read 19 ASH, SIMON H.-System of Coal Mining in Western Washington. Discussed by Eli T. Conner, Simon H. Ash 21 MILLER, J. S.-Method of Mining a Steeply Pitching Anthracite Vein by Successive Skips. Discussed by Eli T. Conner, J. S. Miller, J. B. Warriner 22 HARRINGTON, GEORGE B.-New Orient, an Unusual Coal Mine. Discussed" by George S. Rice, Eli T. Conner, John A. Garcia, George B. Harrington, F. F. Jorgensen, Graham Bright, W. M. Hoen, George N. Simpson, W. C. Adams, R. W. McNeill, Chas. C. Whaley, Carl Scholz, E. T. Gott, Andrews Allen 23 PERROTT, G. ST. J.-Properties of Liquid-oxygen Explosives. Discussed by George S. Rice 48 Safeguarding Coal-mining Operations against Danger from Oil and Gas Wells Discussion of the paper of A. W. HESSE, presented at the New York Meeting, Feb-ruary, 1925, and issued, as Paper No. 1412-F, with MINING AND METALLURGY, February, 1925. A. W. HESSE.-The well under investigation, No. 101, Fig. 2, was started about Sept. 5, 1921, and drilled-in in November. The first hole was started with a 13-in. bit and reached the Pittsburgh coal at a depth of 563 ft.; at 602 ft. the 10-in. casing was run in and the well was continued with a 10-in. bit and 1400 ft. of 8-in. casing was put in. It was then continued to a depth of 1770 ft. and 6-in. casing put in; then continued to a depth of 2555 ft. where the gas was struck. As the well produced only about 100,000 cu. ft. per day. 2-in. tubing was used to conduct the

Jan 6, 1925