Search Documents

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield-point of 16,000 lb. for pure electrolytic iron, one reaches a -maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated Yensen observed an enormous drop in elongation and area reduction at about 2.65 per. cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to. 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated: "Whereas, the American Institute of Mining and Metallurgical Engineers is organized for purely professional and scientific purposes, and whereas diversity of opinion among its members on partisan or political questions is inevitable, it is the expressed policy of the Institute to refrain from official participation or action in political and semi-political matters." AND WHEREAS, appeals for additional advice have been received: NOW, THEREFORE, IT IS RESOLVED: (1) That the policy of the Institute is to refrain from official participation or action in controversial non-technical economic subjects; further (2) That if any Local Section is in doubt as to the application of this policy to any particular subject, it should communicate with the Secretary of the Institute for advice.

Jan 1, 1940

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated: "Whereas, the American Institute of Mining and Metallurgical Engineers is organized for purely professional and scientific purposes, and whereas diversity of opinion among its members on partisan or political questions is inevitable, it is the expressed policy of the Institute to refrain from official participation or action, in political and semi-political matters." AND WHEREAS, appeals for additional advice have been received: NOW, THEREFORE, IT IS RE¬SOLVED: (1) That the policy of the Institute is to refrain from official participation or action in controversial non-technical economic subjects; further (2) That if any Local Section is in doubt as to the application of this policy to any particular subject, it should communicate with the Secretary of the Institute for advice.

Jan 1, 1946

By K. A. ACKLEY

The petroleum industry experienced a year of satisfactory accomplishment in Oklahoma during 1945. Crude oil production was increased, a new record for recent years was established in well completions, and refinery operations were maintained at a maximum level. Daily average crude oil production increased to 382,000 bbl., reflecting a 13.5 per cent gain compared with production during the previous pear. Total wells drilled during 1945 amounted to 2556, a gain of 28.7 per cent over 1944 Refinery throughout averaged 187,500 bbl. daily, an increase of approximately 4 percent over the preceding year.

Jan 1, 1946

Aamot, Olav Crone, Chem. Engr., Norsk Elektrokemisk, Kongensgt. 18, Olso. Norway. '29 Abadilla.-Quirico A., Dir., Bureau of Mines Manila, P. I. '38 Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1212 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L., Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '29 Abel. Walter D., Cons. Engr 1839 Holmby Ave., W. Los Angeles. Calif. '32 Abele, Louis T R. F. D. 5. Susquehanna Trail, N., York. Pa. '31 Abell, Leo M., Ore Dressing Investigator, School of Mines Adelaide, S. Australia. '31 Abenius. Hakan V., Mine Supt., Bolidens Gruvaktiebolag Boliden, Sweden. '37 Aborn, Robert H., Asst Met., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service-Club, 16 St. James' Sq., London, S. W. 1, England. '28 Abrams. Charles Jackson 1624 17th St., Denver, Colo. '36 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho. '27

Jan 1, 1938

By P. A. Beck, M. V. Nevitt

All binary and a number of ternary u alloys formed by first long period transition elements were examined and found to be ferromagnetic at low temperatures. The Curie temperatures for these alloys were measured. It was found that the correlation of the Curie temperature with composition may be described qualitatively in terms of the contributions of the various component atomic moments to the saturation moment of the alloy. Ternary Fe-Cr-Mo u phase alloys were also found to be ferromagnetic, with a Curie temperature dependent on the iron content and largely independent of the unit cell dimensions. Similar relations were found for the Co-Fe-Cr and the Co-Cr-Mo a alloys, where the Co + Fe content appears to determine the Curie temperature. RECENTLY, it has become increasingly evident that the u phase is some kind of an "electron compound." Several papers1-' discussed the empirical correlation between the composition of the various u phases in alloys of the transition elements and the distribution of electrons in the partially filled d-levels of the component atoms. However, a picture of the latter can be formed only in a more or less intuitive manner, as in the Pauling theory," and the rigorous treatment of these problems is at present prevented by lack of adequate knowledge of the electronic structure of the transition elements in the metallic state. It appeared reasonable to expect that investigation of the magnetic properties, which are related to d-shell electrons, may help in clarifying the physical nature of the foregoing empirical correlation. Qualitative tests of samples of various compositions have shown that certain u alloys become ferromagnetic at liquid nitrogen temperature." The present investigation was undertaken to determine whether or not low temperature ferromagnetism is characteristic of a large variety of u alloys and to establish how the Curie temperatures of ferromagnetic u alloys are influenced by changes in composition and in lattice parameter. In the first portion of the in- vestigation, Curie temperatures were measured for a series of u alloys containing either vanadium or chromium with one or two of the elements manganese, iron, cobalt, or nickel. In the second phase of the work, data were obtained on the Curie temperature of ternary (Fe, Co, Cr)a, (Fe, Cr, Mo)a, and (Co, Cr, MO)U alloys, as a function of composition and of interatomic spacing. Experimental Procedures High frequency vacuum melting in high purity re-crystallized alumina crucibles was employed in the preparation of the u alloys, using metals whose lot analyses are given in Table I. Approximately two-thirds of the alloys were analyzed chemically, the analytical results being in acceptable agreement with the intended compositions, as seen in Tables I1 and 111. The specimens were annealed for homogen-ization in an atmosphere of purified 92 pct He and 8 pct H, mixture or in evacuated and sealed Vycor tubes at temperatures from 780" to 1300°C, depending on the temperature range of the u phase field for the particular composition. The annealing temwerature and time for kach alloy are given in Tables 11 and 111. Curie points were determined by an induction method; the change with temperature of mutual inductance between two coils was observed when the i-u specimen was inserted into the flux path between the coils. The transformer consisted of three coils each containing 1200 turns of 0.0050 in. diam enameled copper wire. The center coil, P in Fig. 1, served as the primary coil, and was linked magnetically with each of the two secondary coils, S, and S? which were connected in series opposition. The primary coil, P, was energized by an audio-oscillator, set at a frequency of 500 cycles per sec, while the signal from the transformer secondary circuit,

Jan 1, 1956

The following list contains the names of members whose death notices have been printed in MINING AND METALLURGY from March 15, 1947 through March 15, 1948 Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns Year of Election - Name - Date of Death - Issue Containing Biography - Page 1938 ABERNATHY, G E , (M) Feb 6, 1948 April 1948 266 1935 ARCHER, M T, (M) Oct 26, 1947 Dec 1947 633 1947 ATIKINSON, JAMES E, (S) Feb 6, 1948 June 1947 309 1940 AYRES, VINCENT L, (M) Oct 14, 1947 Jan 1948 59 1915 BABCOCK, JAMES E , (M) April 1, 1947 June 1947 309 1942 BAGGALEY, WILLIAM BLAIR, (A) Aug 28, 1947 Jan 1948 59 1897 BUIN, II POSTER, (M) Mar 9, 1948 April 1948 219 1945 BAMPFIELD, A E (M) Unknown Mar 1948 215

Jan 1, 1952

THREE regional meetings are planned for this summer and fall following the spring meeting held under the auspices of the Iron and Steel Committee and the Ohio Section at Cleveland in April and in lieu of a general fall meeting of the Institute. Plans for all of them are maturing rapidly. Excellent programs and. interesting visits to points of local tech¬nical interest are already assured. THE SALT LAKE CITY MEETING This meeting will be under the auspices of the Milling Committee and the Utah Section. It will be one of the features of the joint convention held the week of August 22 to 26 with the Western Division of the American Mining Congress. The Congress will be responsible for the general arrangements and for the program on the first day. The following general committees have been appointed:

Jan 7, 1927

By R. V. Norris

The anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, iii the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of' the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jan 1, 1912

By George C. Toland

In 1950 the phosphate fertilizer market warranted the design and construction of a new fertilizer plant by Cominco at Kimberley, B.C. The initial rated capacity of the plant was 70,000 tons per year of high- grade ammonium phosphate. The plant was placed on-stream in 1953. One of the major problems in operating the fertilizer plant was the disposal of the gypsum tailings slurry which was a by-product of phosphoric acid manufacture. The original weight of dry tailings produced by the mill was 500 tons per day. This quantity increased over the years until a projected 2200 tpd was selected for the pond design described in this paper. The original gypsum tailing area was located south of the fertilizer plant and adjacent to the St. Mary's River. By 1965 the original disposal area had proven inadequate and Cominco's engineering staff had selected a 500 acre disposal site to the east of the plant.

Jan 1, 1971

By F. R. Hutto Jr., F. L. Kady Jr., L. E. Weymouth

The behavior of particulate non-metallic materials in moving contact with smooth surfaces is of interest and concern to manufacturers and users of abrasives, of fillers, and of pigments alike. The theoretical aspects of the subject have been treated to considerable extent in the literature, and correlatic,ns are available that attempt to relate various methods of hardness determination." 2 The particle size and friability are characteristics of the abrasive that are not related to the smooth surface. The hardness, on the other hand, may be visualized as relative to that of the smooth surface. In a study of abrasive action, the role that hardness, per se, plays is a complicated one. For it is necessary to compare the "hardness" of the abrasive, usually a non-metallic, with that of the smooth surface, generally a metal. Hardness of non-metallics is defined as resistance to scratch and is almost universally described with respect to the Mohs scale.3 Minerals have been rated by Mohs numerically from the softest (talc = 1) to the hardest (diamond = 10). By definition, a mineral has a designated hardness when it is scratched by the standard that is numerically just above it on the scale; and conversely, when it scratches the standard that is just below it. Hardness of metals. however.. implies resistance to indentation, a property that has been measured by a number of methods. In fact, the indentation hardnesses of the standard minerals on the hlohs scale have been determined by the Rockwell tester. Reproduced below are two versions of this correlation. 'A conversion chart, prepared by Wilson Mechanical Instruments Division of American Chain and Cable Co., merely gives the conversion from Rockwell to Knoop hardness. The relation between Knoop indentation hardness and Mohs scale has been reported by G. S. Smith — A New Scale of Hardness, The Engineer, Aug. 26. 1949. G. F. Kinney in Engineerin Properties and Aplications of Plastics reports the Rockwell hardness of the minerals directly in the Mohs scale. The question immediately arises as to whether this relation is valid when applied in reverse; namely,

Jan 1, 1961

By F. M. Morris

A large reserve of thick coal in southwest Virginia was developed by Clinch-field Coal Co. in 1957-1958 to produce a nominal rate of 1500 tph raw coal. Operation features coal cleaning in transit. Refuse removed averages 35 pct. Evolution of plant from initial conception to completion is discussed, selection of means applied is explained, and performance to date us design expectation is described. The long-range plan calls for ultimate handling capacity of 40,000 tpd raw coal with anticipated clean coal capacity of 26,000 tpd on a three-shift basis. From a materials handling viewpoint, the Moss No. 3 operation is principally of interest as an ensemble. Generally speaking, it uses time-tested equipment and ideas but some of these are employed on a scale that may be new in the industry. At present about 20,000 tpd of raw coal are being handled. This is expected to increase to 40,000 tpd as soon as business conditions justify it. The purpose of this paper is to discuss the evolution of the plant as to materials handling practices, to describe briefly the equipment and methods used, and to comment on performance in certain areas. The subject divides itself naturally into four phases: 1) operations at the mines, 2) transportation from mines to plant, 3) raw coal handling into the plant, and 4) transportation of refuse away from the plant. OPERATIONS AT THE MINES The coal reserves for Moss 3 are in southwest Virginia where Dickenson, Russell, and Buchanan Counties come together. This area contains about 15 square miles and over 100,000,000 tons of coal. Here the No. 4 (Tiller) and No. 5 (Jawbone) seams of the Norton Formation lie so closely together that for practical purposes, they constitute one seam of coal. This seam, which is called the Thick Tiller, varies from 10 to 18 ft in thickness and underlies Sandy Ridge, a mountain cresting between 2400 and 3300 ft above sea-level. At 18-ft seam height (which is considered to be the maximum practical mining height) the parting between seams will be about 3 1/2 ft thick and each bench of coal will be about 7 ft thick. Depending on the amount of impurities in the seams Drover. total reject in this height coal may approximate 50 pet by wt. It will average about 35 pet for the property as a whole. The first move in developing this resource was made in 1953 when contour maps of several square miles around Duty, Va., including all the known outcrop, were made by photogrammetry. At this time, it was felt the prospective operation would be served by the Clinchfield Railroad and a photogrammetric route survey was made by this railroad from Haysi to Duty. Study of the resulting maps indicated only one site—adversely owned—which might accommodate the size washing plant to be erected. Water resources of a dependable nature seemed nonexistent. In 1954 bulk washability tests were made on the Tiller Bench at the Moss No. 1 preparation plant. The tests indicated this portion of the seam, mined separately, would wash to 4 pet ash with good recovery. Also in 1954, development of Moss No. 2, south of Sandy Ridge, was begun. This mine is in the Tiller Seam where it is about 100 ft below the Jawbone Seam. The reasons for developing a mine in the normal Tiller Seam before tackling the Thick Tiller seemed compelling: Railroad service could be established quickly, communications were better (though not good!), more was known of the seam (it had been mined in the years 1911 to 19241, and there was no essential property to be acquired. After some legal skirmishing, the Norfolk & Western Railroad was granted the right to serve the new mine. Three decades earlier the old mine had been served by the Clinchfield Railroad. The event which triggered active development of Moss 3 was the Appalachian Power Co.'s decision in 1956 to build a 450,000-kva power plant on Clinch River at Carbo. This solved the problem of marketing the steam coal which inevitably must be a product of a mine in the Thick Tiller. Management promptly decided to build the preparation plant at Carbo where an excellent site was owned; where railroad service existed; where telephone service could be obtained; and where roads, bridges, and water supply were tolerable.

Jan 1, 1961

By Sidney Snook

FLUORSPAR production is the most important industry in a compact area in southern Illinois and western Kentucky bordering the Ohio River. Producers' activities do not usually figure much in the mining news of the country, so that few know that the last year or so has been an unusually active one. Mine shipments more than doubled in 1939 compared with the poor year 1938. The average price changed but little, though it is now about one-sixth higher than at the beginning of last year. The outbreak of war in Europe a year ago lent an immediate stimulus to the industry, though only about 15 per cent of the domestic consumption is normally imported, thanks to a tariff of $8.40 per ton, equivalent to about 30 per cent ad valorem. Be- cause of the increased production and many expansions and improvements in the mines and plants, the period since the beginning of 1939 has been the most important one for the industry in the last 15 years.

Jan 1, 1940

By Walter Kauenhowen

GeRmany's crude-oil production during 1936 totaled 3,112,494 bbl., an increase of 5.2 per cent over the 3,007,711 bbl. produced in 1935. The official monthly production figures published in 1936 report only the individual production figures of the three old established fields, whereas since 1936 official reports combine the production of all other fields into one figure. According to these published data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1936 was as follows:

Jan 1, 1937

By Bobby P. Faulkner

The Tennessee Copper Co.'s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By John Stewart

The market at present supplied by shipments from the phosphate districts of Quebec, Ontario, and New York State requires high-grade ore, carrying from 75 per cent. to 90 per cent. of phosphate of lime. In sorting out such material by hand, much valuable phosphate is necessarily left in the "culls" or refuse, besides which, much phosphate-rock of low-grade is not now mined at all, because it cannot be made available by the crude method of cobbing and hand-sorting. The utilization of such material, which would, of course, greatly benefit this industry, requires either a mechanical separation or a chemical process which would concentrate the phosphate in a form suitable for agriculture. Considering the rich phosphate now shipped as the first class, we may arrange the lower grades in three classes, as follows: Second Class.—Cull-ore from the first class, and the mass of deposits having, as gangue, pyroxene or hornblende. The following table gives the hardness and specific gravity of the minerals concerned: Hardness Spec. gravity. Apatite,....... . 5 3.1 to 3.25 Crystalline limestone (pink calcite),. 3 to 4 2.5 to 2.9 Pyroxene,..5 to 6 3.23 to 3.5 Hornblende,.5 to 6 2.9 to 3.4 Feldspar (orthoclase),. .. . 6 to 6.5 2.5 to 2.6 It is evident that when pyroxene and hornblende are present in large proportions, this ore cannot be successfully concentrated by crushing and jigging. It may be reduced to fine powder by successive treatment in a rock-breaker and a Sturtevant or Frisbee-Lucop mill, or other suitable apparatus, and in this condition it could be largely used by applying it freely upon exhausted clay soils, such as occur in Quebec and Ontario. The occupants of these once fertile river-lands are, however, hard to move in the direction of such improvements. When water-power is at hand, the cost of crushing

Jan 1, 1893

By AIME AIME

AMONG the recent mining and metallurgical developments in England great interest has been shown in the development of an iron-ore field covering 26,0.00 acres in Northamptonshire, containing 500,¬000,000 long tons of ore; and the erection at Corby, by Stewarts & Lloyds, of a modern basic bessemer steel plant and tube works. The entire project was planned to cost about £3,300,000. Many improvements have been made in the varied equipment that is being installed, some of which has set mew records for massiveness. There is, for instance, a new roll crusher, which has been manufactured by Hadfields, Limited, of Sheffield, the largest ever built in England, and weighing 130 tons. This machine, shown in Fig. 1, as erected at the Hadfields shops, is primarily designed to take blocks of iron ore as they come from the steam shovel. The maximum size is 54 by 48 by 36 in., hut occasional pieces slightly larger than this may be accommodated. The capacity is upwards of 500 tons per hour, the product passing to a secon-

Jan 1, 1934

By Horace R. Graham

CHEMICAL nitrogen and the "nitrates" of commercial significance are derived mainly from three basic sources: (1) the natural deposits in the form of nitrate-bearing earth and clay, which, being largely water-soluble, can exist only in the most arid portions of the earth; (2) coal, which yields not only nitrogen but also the additional by-product hydrogen required for the synthesis of ammonia and its compounds; (3) the atmospheric air, which contains 75.5 pct by weight of pure nitrogen gas. NATURAL NITRATE DEPOSITS Occurrence Although natural nitrate deposits consisting principally of the salts of sodium and potassium have been reported in Egypt, South Africa, Mexico, Argentina, Colombia, Peru and the USA, the only known natural nitrate resources of commercial importance are the vast deposits found in the Atacama, Tarapaca and Antofagasta regions of northern Chile, lying in a narrow strip 10 to 50 miles wide and roughly 450 miles long, between latitudes [19O] and [26OS]. In addition to yielding nitrates of sodium and potassium, these deposits are the source of the major portion of the world's supply of iodine. The nitrate-bearing ores known in Chile as caliche are variable in composition and may contain from 5 to 30 pct each of nitrate, chloride and sulphate. While the deposits are present chiefly in the form of the sodium salt, potassium, magnesium and calcium also occur in percent- ages from 0.1 to 5; usually as double salts with sulphate, which are but slightly soluble in nitrate leach solutions. These double salts are bloedite(Na2S04.MgS04.4H,0), glauberite (Na2S04.CaS04), polyhalite (K2SO4.- MgS04.2CaS04.2H20). Some deposits contain up to30 pct of their ni-

Jan 1, 1949

By A. L. Sweetser

EXPERIENCE has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorination-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave : Fe2O3, 3.35; FeS, 1.5; MnO2, 0.75; ZnCO3, 4; Al2O3, 3.20; H2O, 0.7; SiO2 and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, .and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size-a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Sep 1, 1907

By Westwater, J. S.

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W. within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleveland-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. A1len. Mather "A" shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather " B, " also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation.

Jan 1, 1949