Search Documents

By H Haas

H. HAAS, San Francisco, Cal. (communication to the Secretary?). -Fig. 1 plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on' the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would he well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that "two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saving that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient, demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the Southwest, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market.

Jan 5, 1917

By J. L. Christie, R. H. Leach

SO much has been written recently about the use of silver to replace scarce metals that certain facts about silver and its uses should be of interest. Figures for the production and use of silver, taken from the Handy & Harman annual reviews of the silver market, are given in Table 1. It will be seen that the rate of production has remained fairly constant and has been affected in recent years by the production of base metals, of which silver is a by-product. In each of the years 1937, 1938, and 1939, the U.S. Government acquisitions alone exceeded the entire world production, the difference, of course, being made up by imports of previously accumulated stocks. In 1940 and 1941 the U. S. Government acquisitions plus the United States and Canadian uses in the arts and industries exceeded the Western Hemisphere production. The U.S. Government pays a premium price for silver newly mined in the United States, at present 71.11c. compared with the price of 35'/8c. for foreign silver, with the result that the current U. S. production is not used commercially for the arts and industries. At the time this is written (June 1942) there is much uncertainty as to the future effect of this situation.

Jan 1, 1942

By Harold L. Overton, Leonard B. Lipson

The first paper in this series1 outlined practical methods for applying the theory of steady-state flow of an ideal Bingham plastic liquid through a circular pipe and axially through a stationary concentric annulus to the enginekring analysis of friction loss problems. In the present paper the properties of another useful rheological model, the pseudoplastic generalized Newtonian liquid, are considered. The terminology applied to the rheological models is derived from the following classification of rheological models. The term "generalized Newtonian" is a class designation applied to models which do not have yield points but which exhibit a dependence on shear rate. The term "pseudoplastic" applies to a sub-group of models within this class which exhibit a decrease in "viscosity" with increasing shear rate. The term "power model" refers to a mathematical model proposed for describing the behavior of the pseudoplastic liquid. This model is of interest since certain of the salt saturated, oil emulsion, and "low solids" drilling fluids, inverted emulsion- and oil-base drilling fluids, aqueous gels, gelled crudes and blocking agents employed in hydraulic fracturing operations are of this type. The present treatment considers the equations describing steady-state Poiseuille flow through a circular pipe and a stationary concentric annul us, and Couette flow between concentric rotating cylinders for a particular pseudoplastic model. As in the previous paper' it is demonstrated how these equations can be applied to engineering calculations of friction losses. Graphical procedures for recovering the various flow curves and cxample calculations are included. A method for simplifying turbulent-flow correlations is also proposed. PROPERTIES OF PSEUDOPLASTIC GENERALIZED NEWTONIAN LIQUID In contrast to the Bingham plastic the generalized Newtonian liquid is yield point-free. However, in the flow region the relation between stress and rate of shear is not linear as it is with ordinary Newtonian fluids. If the stress increases with shear rate at a less than linear rate the system is called pseudoplastic. While there is no yield point in this system, the Bingham advocates' coined the term pseudoplastic to distinguish this kind of behavior from Bingham plastic behavior. For the pseudoplastic a plot of flow rate vs friction loss or rpm vs torque, from pipe flow or rotational viscometer measurements, respectively, generally has three qualities: (1) it can be clearly extrapolated toward the origin; (2) there is very little slope at the origin. This accounts for the high apparent viscosities at low mixing and pumping rates; and (3) the flow curve possesses a continuous curvature which gradually diminishes as the shear increases. Rheological measurements on a pseudoplastic liquid can be easily misinterpreted as indicating Bingham plastic behavior. A typical case in point is illustrated in Fig. 1. These data were obtained from measurements on an oil-emulsion mud using a commercially available rotational-type viscometer (Model 35 Fann V-G meter). Applying the "two-point"* method3 gives a plastic viscosity of 17 cp and a yield point of 24 lb/100 ft2; at the same time weighting material settles very easily in this system. This illustrates that it is not possible to distinguish between the pseudoplastic and the Bingham plastic from only two data points. It is possible to determine qualitatively which model is more appropriate by a combination of dynamic and static measurements. Experience indicates that the simplest criterion for the Bingham plastic liquid is that the calculated dynamic yield point should be of the same magnitude as the measured gel strengths. For the oil-emulsion drilling fluid illustrated in Fig. 1, a value of 4 lb/100 ft2 was obtained for gel strengths measured

THE solid nonmetallic inclusions present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general, the term non-metallic inclusions seems to be satisfactory and adequate. NATURE AND CONS1lTUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those occurring as a result of reactions taking place in the body of molten or solidifying metal and (2) those resulting from mechanical incorporation of refractories or other materials with which molten steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag-stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulfides but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from molten or solidifying steel may be caused by: (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change

Jan 1, 1964

By W. F. Boericke

WORLD production of silver in 1929 totaled 256 million ounces. In 1928 production was 258 million ounces, and in 1927, 254 million ounces. With an actual decrease in the amount of silver produced last year, as compared with 1928, and an increase over 1927 of less than one per cent, obviously there has been no overproduction of the metal in the popular sense. But the price of silver tells a different story. For 1927, the average quotation was 56.37 cents; it was 58.17 in 1928, and 53.0 in 1929. During the last year it reached a high point of 57 cents in January, and fell steadily, without interruption to the downward trend, to a low of 47 cents in December. Since then it has dropped to an all time low of 43 cents on February 6.

Jan 1, 1930

By Albert Ladd Colby

A GLANCE through the Bibliography appended to this paper will show that the Transactions of this Institute contain what virtually contitutes a history of the development of the manu¬facture of steel rails in this country and abroad. It is, therefore, fitting that this paper, bringing one branch of this important subject down to date, should be here presented, and it is also appropriate to select this joint meeting of our Society with the Iron and Steel Institute to compare the specifications covering the rails produced in these two countries, and to propose a standard specification to govern the manufacture of American rails for export. During the last ten years the production of Bessemer steel rails in the United States and Great Britain has amounted to 32,128,720 gross tons. Nearly 19,000,000 tons have been rolled in the past five years. The next five years will see an even larger output, owing partly to the extension of railway projects in the Orient, in South and Central America, in Mexico, and in Australia and the other British Colonies. Of late years, the American rail-mills have so largely increased their daily output, that trade conditions have often made possible the delivery of American rails to foreign ports. The tenders submitted by American mills, however, have always been accompanied by requests for changes in the foreign specifications, chiefly in the reduction of the amount of testing required; and it has only been natural, especially at first, that the engineer, whose specification had always been accepted without question by British mills, should interpret American tenders 'as an evidence that an inferior rail would be furnished

Sep 1, 1906

THE solid nonmetallic inclusions that are present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and. this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general the term "nonmetallic inclusions" seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those that occur as a result of reactions taking place in the body of the molten or solidifying metal and (2) those that result from the mechanical incorporation of refractories or other materials with which the steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulphidea but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from the molten or solidifying steel may be caused by (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change in equilibrium constants as the steel cools to the freezing temperature, (4) decreased solubility with lower

Jan 1, 1944

By R. E. Morgan, D. L. Douglass

The determination of phase relationships and solid-solubility limits can be performed by quantitative metallography in addition to the usual X-ray and metallographic techniques. For example, Beck and smith1 redetermined the ß/ß + ?, ß + ?/?, a/a + ß and a + ß/ß boundaries in the Cu-Zn system by measuring the volume fraction of second phase of several alloys and extrapolating the volume fraction-composition curves to 0 and 100 pct. A modification of this technique is suggested for certain alloy systems, in which it is not necessary to use several alloy compositions but merely one. A single two-phase alloy may be used to determine terminal solubilities in the following manner. The method consists of equilibrating samples of the alloy in a two-phase region adjacent to the desired solid solution, at three or more temperatures, quenching, measuring the volume fraction of second phase present, and applying an analytical treatment to calculate the unknown solid solution. However, two restrictions are inherent in this technique. They are: 1) only certain types of alloy systems are amenable to it, and 2) the general features of the system must be known. The first drawback to the new technique, i.e., that only certain types of systems may be studied, necessitates that the composition at one end of the tieline must either be constant with temperature or well established as a function of temperature. Either a pure metal or some intermetallic compounds fulfill the former. If it is assumed that the volume per gram-atom of a dilute solution is unchanged by the addition of element B to element A, the composition of the solid solution in equilibrium with the second phase may be determined by a material balance and is given by where X, = volume fraction of B in a solid solution Xc = volume fraction of B in compound c X = volume fraction of B in alloy f = volume fraction of second phase The composition by weight may then be determined by the use of tables in the Metals Handbook2 when the density ratio of the solid solution constituents is known. A possible alternative treatment involving the use of the lever rule is less precise than the above tech- nique. This may be used when the density of the solid solution is either known or may be calculated from X-ray data for several compositions. The following analysis is then made. The ratio of compound to solid solution (by weight) may be expressed as follows: x0 - x wc = xr-x = x0 - x r2i Xc -X where Wc = weight of compound w = weight of solid solution x, - alloy composition, weight percent x = unknown composition Xe = compound composition but where V, = volume of compound VA = volume of solid solution pc = density of compound p, = density of solid solution fc = volume fraction of compound fB = volume fraction of solid solution and fs = l -fc then If pc and xc are known, and f, is measured, then pB is the only unknown on the right side of Eq. [4]. The known densities of the solid solution can be plotted for various compositions and can then be expressed mathematically as a function of composition. The use of an expression of pB = f(x)reduces the equation to one unknown—the desired solubility. In the event that the densities are unknown, they may be calculated for various compositions from Vegard&apos;s law. The calculated values are then plotted and expressed analytically. The most accurate results are obtained for Eq. [4] when fc<< 1, i.c., when (x, -x,) - 0, &/l-f, - m; but as fc/l -fc - 0, (xl-x,)- (x, - x), and x - x,,. However, the accuracy with which fc can be measured decreases as f, decreases.3 Alloys for investigation must be selected by a compromise, which is based upon an error analysis of Eq. [4] and knowledge of the accuracy of volume fraction measurements. An examination of phase diagrams in the literature showed many which were amenable to the technique described here. The zirconium-copper system was selected in order to determine the solubility of copper in beta zirconium. Pieces of an alloy which was arc-melted three times were wrapped in tantalum foil and sealed under an argon atmosphere in Vycor tubes. The sealed samples were equilibrated at temperatures from 850" to 960°C for 3 weeks and quenched to room temperature by smashing the capsule in water. Several planes of polish were examined, and

Jan 1, 1960

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith&apos;s&apos; concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman&apos; who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By H. C., Simpson

MANY metals by virtue of their place of occurrence as ore, and their uses are travelers! Iron and steel, for instance, is one of the greatest of travelers in the form of ships and the romance of iron in this respect is only just beginning to be superseded by the stories which can be told of the travels of aluminum and its alloys, used in the building of airplanes. Tin is a traveler from the Straits Settlements to this country and Europe, for use in the canning industry; afterward traveling all over the civilized world as a part of the container for preserved foods. Silver is somewhat of an aristocrat, when its uses are measured against those of the baser metals. From earliest times it has been used for adornment (first perhaps o4 the person and later for the embellishment of weapons and&apos; buildings), for the making of fine ar¬ticles used in the household, and as money. While its uses have been widened by the discoveries in chemistry, electricity and other sciences, its early uses are still much in evidence in our modern life.

Jan 1, 1928

By Schumacher, Earle E.

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10" C. in temperature. The precise location of this line is also important in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By H. G. HYMER

B ECAUSE of its remote geographical position and inaccessibility, little is generally known of the mining and prospecting in Northern Rhodesia. In this rather new and promising region, the development of mines presents many difficulties. Although many mineral discoveries have been made, progress in .prospecting the huge mining concessions has been handicapped by the lack of roads, communication, transportation, native population and incomplete knowledge of geology.

Jan 1, 1929

Jan 1, 1885

By W. Lawrence Austin

Jan 1, 1884

By H. David Swain

On Bougainville Island in Papua New Guinea, Bougainville Copper Ltd. (BCL) has successfully applied electronic data processing (EDP) techniques to pit operations and mine planning. Though the EDP program is not complete, BCL has realized significant improvements in short and long range mine planning, and equipment and manpower utilization. About 80% of BCL&apos;s 4000 employees are Papua New Guinea nationals, and most have little education or training. The operational characteristics of the computer equipment, however, have been quickly adapted by users with low educational standards.

Jan 3, 1979

MR. Woo&apos;s succinct description of the mining and smelting of silver-lead in Mongolia, with the roasting-and-reduction process and cupellation, has much interest as a picture of methods that not only may have been in use, as he suggests, a thousand years ago, long before the existence of mining schools or chemical laboratories, but probably vary little, if at all, from the practice of prehistoric times, when King Priam&apos;s handsome silver vases, cups and bowls were formed. For it is highly improbable that such large objects were made from comparatively rare native silver, and the metal must have been smelted from ore, and most likely in great part from galena,, with cupellation of the lead. Dr. W. A. P. Martin, in his excellent book on the Lore of Cathay, points out that Chinese alchemy is over 2000 years old, antedating the European by at least six centuries; and he infers that the Chinese skill in metallurgy and many branches of practical chemistry owes its origin to " those early devotees of the experimental philosophy who passed their lives among the fumes of the alembic." Those alchemists, however, may have more likely derived some of their leading ideas from the mys terious, and at that time wholly unexplainable results observed in already very ancient metallurgical processes; in which, for example, certain stones were transmuted, as it were, into metals widely divergent in character from their ores, and even silver and gold were obtained from the most unlikely-looking mate rials. It is therefore, in any case, not improbable that the Chinese may have preceded western nations in the discovery of metallurgical methods. At all events, it is now evident that the Japanese acquired these arts from China, the former source of all their higher civilization. My own observation of old-fashioned silver-smelt ing at Hosokura, on the main island of Japan, and about 220

Jan 1, 1903

By W. M. Peirce

COAL&apos;S importance in the metallurgy of zinc may be gauged by the fact that approximately a million and a half tons is so employed annually in the United States. This brief paper will show in what way the various steps in the treatment of zinc ores utilize this fuel, either in its primary form or as coke or gas, and to what extent. The first step in zinc metallurgy that requires the use of fuel is roasting the sulphide ore, which is the type of ore in which zinc commonly occurs. Since the roasting is nearly or completely autogenous, however, this use of fuel is too minor to warrant further attention. Concentration of zinc ores is usually carried out by conventional milling methods, but a pyrometallurgical method, the Waelz process, is used to concentrate certain low-grade ores, and to recover the zinc content of certain residues in concentrate form. The Waelz process uses a continuous rotary kiln in which a mixture of coal and zinc-bearing material is heated to a

Jan 1, 1948

By AIME AIME

TO THE AMERICAN MINING CONGRESS. AMERICAN INSTITUTE OE MINING ENGINEERS. MINING AND METALLURGICAL SOCIETY OF AMERICA. The committee that makes this report was appointed at the meeting of the American Mining Congress, at Denver, Colo., in. November, 1906. The appointment had in view the drafting. of a law for the regulation of quarrying and metalliferous mining under the police laws of the States, with the hope that the uniform adoption of such a law could tend to reduce the number of accidents in mining. Since its. appointment, the committee has had&apos; under serious and continuous consideration the matter with which it was charged. At the meetings 0f the American Mining Congress in 19o7, 1908 and 1909, it reported progress. At the meeting in 1909 it was authorized to present its report not only to the American Mining Congress, but also to the American Institute of Mining Engineers and the. Mining and Metallurgical Society of America, and to present its report in printed form during the interim between meetings of the American Mining Congress. The committee collected from the officials of the States of the Union copies of their mining laws. With the assistance of the Engineering and Mining Journal copies of the laws 0f Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New aland, and certain European countries were also obtained. These laws were subjected to careful study. The first publication of the committee was a summary of the more important metalliferous mining laws 0f this country. Upon the basis of the existing laws of the States of the Union, Great Britain, and the English speaking colonies, a tentative draft. was prepared and printed in limited number in 1909, for convenience in securing the advice and criticism of a considerable number 0f persons engaged in the mining industry. In this way valuable suggestions were received. At the request of the chairman of this committee, Mr. Frederick L. Hoffman, statistician of the Prudential Insurance Company, of Newark, N. J., summarized and reviewed the available statistics of fatalities in metalliferous mining in the United States. Mr. Hoffman&apos;s report was published in the Engineering and Mining

Jan 10, 1910

By W. T. Malone, J. R. Williams, R. L. Tiner, J. M. Tinsley

Hydraulic fracturing methods for production stimulation have become a common procedure in the oil and gas industry. Fracturing treatments are performed on wells of various potentials to help increase the production rate. In addition to the desire for increased production is the need to predict what increase might be expected. This knowledge is useful in economical treatment planning to accomplish the desired production goals for the well. Theoretical production increases due to horizontal radial fractures may be calculated using equations developed from mathematical analyses and electrical models.1,2,6 It also is possible to predict theoretical production increases due to vertical fractures using curves developed from electrical3 and mathematical models.8 However, these studies assumed that the vertical fracture height and the formation height were equal, which may not be true." In addition, the final fracture height through which fluid is produced may not be equal to the created height. The development of vertical fracture proppant transport relationships has made unrealistic the assumption that propped fracture height is equal to created fracture height. Through the use of published proppant transport equations,4&apos;12 it is possible to calculate the height of a bed of propping agent deposited in a fracture of a given height. Assuming that the fluid flowing in the fracture moves through only the propped portion of that fracture (i.e., that the un-propped part of the fracture heals) it becomes essential to know how production increase varies with the ratio of propped fracture height to formation height. It should be recognized that future investigation may determine that the fracture does not heal completely and that a highly permeable channel exists over the deposited bed of proppant. The effect of this channel was not considered for the present study. The following analysis of experimental data allowed development of curves to determine theoretical production increases considering fracture height as a variable. Discussion In designing a fracturing stimulation treatment a number of variables must be considered. The size of the treatment, type of proppant used, proppant concentration, treatment fluid properties and well conditions are all factors affecting the dimensions and permeability of the fracture. Production increase due to a vertical fracture is affected by propped length, height, width and permeability of the fracture for a given set of formation conditions. Production increase may be defined as the ratio of production rate after fracturing to the production rate before fracturing at the same pressure differential, pe — pw. The producing rate in an

Jan 1, 1970

By DR. SAMUEL B. CHRISTY

? THE man is always greater than his work.? The training of the men who are to develop the mineral resources of the world is the most important problem connected with mining engineering. It becomes ever more important to civilization as the mineral wealth of the earth approaches exhaustion. I have therefore decided to consider a few of the more important problems arising in the training of the mining engineer, and especially those arising in America. THE PECULIAR NATURE OF MINERAL WEALTH. Mining and Agriculture are the two fundamental arts. Without the latter our existence would be precarious; without the former, our civilization impossible. Agriculture furnishes that regular supply of food and raiment which leads to the growth of large communities in which cultivated leisure first becomes possible; while raining furnishes the metallic thread from which is woven that complex fabric we call civilization. But in these two arts the conditions for success are widely different. Most of the crops that the farmer reaps may be harvested year after year, and the proper fertilizers being added, he may continue the annual harvest indefinitely, while, as a result of cultivation, his farm becomes yearly more valuable. But the crop the miner reaps can be harvested but once in the history of the race. Our mineral wealth has taken unknown ages to mature in the bosom of the earth. The ripened fruit can be plucked but once. There are no fertilizers for worked out mines. It never pays to work over a mine that has been

Sep 1, 1905