Search Documents

By Andrea Pezza

The steel market is experiencing a difficult conjuncture: on the one hand steel producers minimize their investments while optimizing their over- production, on the other hand suppliers reduce their internal human resources and capacity in order to overcome the instability of the new era. A return to the steel production levels of the past is not expected in the short term. Research, development and plant concept optimization is one recipe to drive the future of the steel business. This article describes a new concept for a VOD plant developed as a result of thorough investigation and assessment of all possible solutions. A joint and tight cooperation with the final customer was necessary to reaching important results. This article consists of the contributions from the plant suppliers in terms of their experience and feedback, as well as the final user’s. The final customer, voestalpine Giesserei Linz GmbH, and the plant supplier, Primetals Technologies, are both worldwide players and highly focused on reaching best quality and innovation.

Oct 30, 2017

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Wan-sub Kim, Joon-Tae Lee, Seongkyu See, Yong-Kyu Park

Softening heat treatment of CHQ alloy steel (Cr-Mo Steel) is a bottleneck process that requires 90% or more of the entire manufacturing process. In order to reduce the property deviation between edge and center and remove the low-temperature structure problems, CHQ products is heat treated by customers. This technology comes from the idea to solve the problem by applying the concept of “In-line isothermal transformation through initial quenching + heat source addition. Consider the stability of field operations, durability from high ambient temperature and fall of scale, Instantaneous heating and cooling control was required for the conversion of slow cooling and rapid cooling products. An electric heating system was applied to the underside of Stelmor air-cooling nozzle. Using the Scan Pyrometer, the feedback control was performed and fine temperature control was performed through the thermocouple by zone. Through the this technology, it is possible to develop and expand products that can be shortened or omitted by the heat treatment process of customers.

Oct 1, 2019

By Eduardo Vitral

The present study focuses in the simulation of pattern formation by ion beam sputtering on a material surface. This process is responsible for the appearance of unexpectedly organized patterns, such as ripples, nanodots and hexagonal arrays of nanoholes. A numerical analysis of preexisting patterns is proposed to investigate surface dynamics, based on a model derived from a Kuramoto-Sivashinsky anisotropic equation, in a two dimensional surface with periodic boundary conditions. While deterministic, its highly nonlinear character gives a rich range of results, making it possible to describe accurately different patterns. A finite-difference semi-implicit splitting scheme is employed on the discretization of the governing equation. Simulations were conducted with realistic coefficients related to physical parameters (anisotropies, beam orientation, diffusion). The study dealt with a random and a monomode 1D structure initial condition in order to understand how the shape and wavelength of the initial pattern evolve with time. Ripples and hexagonal patterns were observed in the results, being physically consistent with the phenomenon. Moreover, the Method of Manufactured Solution has been used as verification of the developed numerical scheme.

Aug 16, 2017

By Chad B. Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Oct 30, 2017

By Chad Byron Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Aug 16, 2017

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By Renata Cristina Teixeira

The lubricant oil is a complex mixture of different basestocks and additives. Engine oils evolved from the use of pure mineral basestocks back in the early years of automotive industry to the advent of synthetic, fully formulated, low ash lubricants. This evolution was driven by a number of factors, such as new engine designs, extended durability needs, increased fuel economy needs, environmental concerns, feedstock prices and availability and legal issues. This paper uses technology prospecting on literature and patents databases to allow an investigation on the historical evolution of engine oils. Main basestocks (mineral, hydrotreated, polyalphaolefins, esters) and additives (antioxidants, antiwear, friction modifiers, detergents and dispersants) are characterized according to their research effort. Technology prospecting data is crosschecked against the evolution of engine oil classes, allowing an analysis of how the main drivers push the development of lubricant oil quality. A research effort was identified in late 1990’s until mid-2000’s and related to the adoption of chemical limits for lubricants. Different patterns for the articles and patents publication account for the high value technological knowledge has in this industry. Technology prospecting is seen as a useful methodology for the understanding and forecast of lubricant technology movements.

Jul 31, 2018

By Arnaldo Forgas Júnior

Three techniques for ferrite quantification were applied in a duplex stainless steel UNS S31803 solution treated at three different temperatures, 1000, 1100 and 1200°C, in order to verify their compliance with the results from ThermoCalc® prediction. It is verified that only austenite and ferrite phases are present in the samples and that an increasing in solution treatment temperature led to the increase of the volume fraction of ferrite. It is also observed that quantitative stereology technique shows absolute values closer to ThermoCalc® predictions. On the other hand, measurements by ferritoscope and XRD show significant deviations, probably due to texturing effect imposed by the rolling process.

Aug 16, 2017

By Marcel Antonio Arcari Bassani

In the mining industry, it is common to have data collected in various formats. In an open pit mining operation, at the early stages of exploration samples are obtained from diamond drillholes. During the production stage, samples are collected from blastholes. The last is more numerous but less precise. From a geostatistical view, this dissimilarity has to be considered to integrate the two sources of information. To combine this different data, three methodologies were investigated: simple kriging with local varying mean, cokriging and ordinary kriging. The exhaustive Walker Lake data set was used and it is considered the source to obtain the true grades. Initially, samples were obtained from the exhaustive data set at a regular spacing grid of 20 x 20 meters. Next, samples were obtained again from the exhaustive dataset at a regular spacing of 5 x 5 meters and a relative error of 25% was added. Then, both data were used to estimate blocks using the three methods mentioned. The grade tonnage curves were compared with the true block grade distribution. Moreover, the block misclassification was evaluated. The results showed that ordinary kriging produced estimates closer to the true block grade distribution and reduced the block misclassification.

Aug 8, 2018

By Aitor Elorriaga Fernandez de Arroyabe

The purpose of Sinter plants is to heat iron ore fines along with fluxes and coke fines or coal, to produce a semi-molten mass that solidifies into porous pieces of sinter with the needed size and strength. Fluxes used in the sintering process need to have an appropriate size distribution and TI to avoid generation of fines, which could reduce the productivity of the Sinter. Besides, a homogeneous chemical composition and high absorption characteristics are necessary to control the basicity and to combine the flux with P, S, Si, etc, respectively. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification, being olivine and serpentine its principal minerals. It is a very homogeneous and hard stone and its main characteristics are: high hot and cold resistance to mechanical stresses, softening and melting points of a flux not of a refractory material. In addition, due to its mechanical and chemical properties, less fines are generated in the sintering process and during the handling and transportation to the blast furnace, improving the productivity of these processes. In this way, the use of PASEK Dunite allows increasing the homogeneity structure of sinter, reducing the percentage of return fines and improving the Sinter productivity.

Oct 30, 2017

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019

By Detlef Ehlert

Energy efficiency is coming to the center of attention in the metallurgical and rolling mill industry due to increasing energy costs, limited resources and political requirements. Also, a green image and energy efficient production is a clear competitive advantage. SMS Siemag, being familiar with automation and measurement equipment, provides an energy data management system which gives transparency over the energy consumptions. All energy relevant media including electricity, gas, water, compressed air and further more can be recorded. The system is manufacturer-independent and allows the use of already installed measuring technology with the possibility of subsequent extension. So potentials for improvement can be recognized and energy savings can be estimated and proven after the implementation of the measures. Being familiar with the processes in the metallurgical and rolling plants, the system by SMS Siemag allows the assignment of the energy data to the production and plant data. Only by this connection, the data can be reduced to key performance indicators allowing authoritative evaluation of energy efficiency. The results are clearly represented on dashboards and support the continuous improvement process. The system also supports the energy controlling with an automatic reporting system, cost center assignment and in support with certification according to ISO 50001.

Jul 30, 2018

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Filippo Verlezza

Conventional wire rod blocks have some limitations. They can only roll with fixed reduction ratios which always require the same rolling diameters within the block. With MEERdrive® SMS, as a pioneer, has introduced an innovative drive concept for wire rod blocks that can overcome the limitations of conventional solutions. The clue: the concept is based on individual drives for each stand position. The exigent wire rod market demand and the available technology melt in a new variant of MEERdrive®, the MEERdrive®PLUS, which represents a sizing block solution for finished size rolling and allows conventional as well as thermomechanical rolling. Further “one family rolling” is also possible, since all roll / size changes will occur in this block.

Oct 30, 2017

By Vitor Orlando Ferreira

The efficiency of an apparatus which uses a forced lubrication system, as well as the useful life of its components, is strongly related to the degree of contamination of lubricating oil. The presence of contaminants and the degradation of the oil itself cause it to release substances that fouling of the wall of the pipes. The cleaning and dialysis of the oil pipes, besides prolonging the life of the lubricant reduces wear of the components. There are several methods of cleaning in pipes, the problem is that some have abrasive characteristics, which could damage some types pipes. Among the non-abrasive methods stand the Flushing and Air scouring. Flushing uses the lubricating oil which circulates in temperatures alternating and high speeds, for generating turbulence to perform washing. The Air scouring method uses oil and filtered compressed air, injected into pipe, to generating higher flow, causing the power supply unit with fluid can work with lower power consumption and higher speeds, removing fouling of the pipe. The objective of this research is to evaluate the Reynolds number to correlate with the efficiency of cleaning the pipe. The method applied was the Air scouring and it was verified that the qualitative effects may occur when compared to Flushing. After testing, it was found that the chosen method brings significant changes in flow, and this flow regime varies considerably increasing the Reynolds number.

Jul 31, 2018

By Francisco Morganti

Weight reduction is the main target of all carmakers, which results in a continuous development of new steel grades. Latest 3rdgeneration advanced high-strength steel grades (AHSS) are complex materials with special chemical compositions and multiphase microstructures. The pickling, annealing and galvanizing processes of these grades aresomewhatdifferent due to the changed chemical compositions and microstructures. Therefore, these innovative steel grades place new demands on the plant technology of pickling, annealing and galvanizing lines. The most significant challenges for the pickling process are sludge occurrence during pickling, varying pickling times, weld ability of the materials, changed visual appearance and required high surface qualities. The most important topic concerning annealing line is a precisely controlled and very flexible heating and cooling process in the furnace.One of the new requirements in galvanizing linesis the prevention of surface faults caused by bare spots, which can occur since these materials feature a higher content of alloying elements like silicon or manganese. Prevention is possible with the special pre-oxidation technologies.Due to the higher strength of the material also the mechanical equipment has to be designed differently in these lines. This paper describes the influences of the changed chemical composition and material characteristics of modern steel grades on the pickling, annealing and galvanizing process and gives an overview about the technical solutions.

Oct 30, 2017

By Daniel Stickel

Current political, economic and ecological guidelines demand the increase of power densities of nearly all machinery parts today. In order to further lower the wear rate towards the ultra-mild sliding wear regime an integral approach is needed, which has to regard contact conditions, surface topography, surface chemistry, as well as sub-surface properties. Still there are no simple parameters to classify the performance of tribosystem. In this study the area and volume affected by tribocontacts are calculated by means of a three dimensional elastic-ideal plastic contact model. The surfaces are generated by means of conventional machining procedures and characterized by scanning white light interferometry. The further input data as to normal and friction forces are derived by ultra-mild sliding wear tests under boundary lubrication conditions of carburized steel against carburized steel and 52100 steel against case-hardened spheroidal cast iron. This contribution will depict the distinct influence of the topography on friction and ultra-mild sliding wear of common Fe-base materials and point on the marked importance of highly localized effects, which govern the acting mechanisms.

Jul 31, 2018

By Alisson Paulo de Oliveira, Altair Lucio de Souza, Jacson Morais Borges, Cleiton Arlindo Martins

A customized version of the Microsim-PM software for one Steckel rolling mill was built and adapted for specific mill parameters. The focus of this study is to use this model, which predicts the austenite grain size distribution evolution during rolling, to understand and quantify metallurgical issues happening during hot rolling. This will allow the steel mill to optimize the rolling process and chemical composition before the first industrial trial. Materials rolled for final thicknesses of 4.75, 6.30 and 12.5 mm of a carbon manganese steel and a microalloyed steel were selected to tailor the equations used by the model and to accurately reproduce the reality of the Steckel mill. This paper analyses the results from the customized model and compares them to mill data and final microstructure. Measured and predicted Mean Flow Stress (MFS) values are compared. After rolling, the material is subjected to accelerated cooling using laminar cooling. These cooling curves obtained from mill data are also considered to analyze the final microstructure characterized for all the cases using EBSD. The quantification of the microstructure allows for a better understanding of the relationship between chemical composition, process parameters and mechanical properties.

Oct 1, 2019