Search Documents

By Tatiane Suelen Santos Silveira, Dagoberto Santos Brandão, Dalila Chaves Sicupira, Graziele Gianini Braga Maria, Marcos Vinícius Fonseca Ferreira, Daniela Barçante Perasoli

O aço inoxidável duplex combina as propriedades mecânicas da ferrita e a resistência à corrosão da austenita, sendo muito utilizado em aplicações industriais que requerem um bom desempenho. Quando submetido a deformações intensas, a austenita transforma-se parcialmente em martensita, aumentando a resistência do aço. Quando o aço é recozido, essa transformação é revertida e a martensita se transforma em austenita, ocasionando um refino de grão do material. Fases secundárias formadas durante o recozimento podem prejudicar suas propriedades mecânicas e corrosivas. Nesse sentido, o objetivo desse trabalho foi avaliar o efeito da temperatura de recozimento na resistência à corrosão do aço inoxidável duplex UNS S32304 laminado a frio. O aço foi submetido à laminação a frio, com deformação de 60%, e posteriormente recozido nas temperaturas de 600°C, 700°C, 800°C e 900°C por um tempo de 0,5 h. A resistência à corrosão foi estudada através da técnica de polarização potenciodinâmica. A laminação a frio promoveu a formação de martensita induzida por deformação (SIM) e a reversão parcial começou a ser observada após recozimento a 600ºC. A ocorrência de SIM promoveu significativa diminuição do potencial de pite e o aumento da temperatura de recozimento aumentou a resistência à corrosão localizada.

Mar 1, 2019

By Luciano Pessanha Moreira, Gabrielle Cristine Lemos Duarte Freitas, Duílio Norberto Ferronatto Leite, Gláucio Soares da Fonseca

Os aços inoxidáveis duplex são conhecidos por sua alta resistência mecânica e alta resistência à corrosão, propriedades que fundamentam sua crescente aplicação em setores químicos e petroquímicos. Tais propriedades estão associadas à microestrutura, que possui frações volumétricas semelhantes de ferrita e austenita, por meio de adições de elementos de liga como Cr, Mo e Ni. Entretanto em processos térmicos a altas temperaturas, este aço pode sofrer alterações microestruturais importantes, onde elementos de liga antes dispostos em solução sólida na matriz dão origem a precipitados intermetálicos, que geralmente são nocivos às propriedades de tenacidade e resistência à corrosão. Este trabalho tem por objetivo o estudo de transformações de fases decorrentes em ciclos não isotérmicos de resfriamento em um aço inoxidável duplex SAF 2205. O experimento contempla uma sequência de quatro ciclos térmicos simulados na Gleeble 3500®. Com o propósito de investigar o processo de precipitação de fases, fez-se o uso da técnica dilatométrica, onde foi possível determinar as temperaturas de transformação de fase nas amostras. Esta informação é validada através dos resultados obtidos no estudo microestrutural via microscopia óptica. Através da correlação entre a fração volumétrica da fase transformada e ensaio de dureza realizado também foi possível garantir a influência das fases encontradas nas propriedades do material.

Oct 14, 2019

By Gilmar Zacca Batista

Este trabalho analisa a tenacidade e dureza do metal de solda e ZAC da solda circunferencial de tubos X65, X70 e X80 para serviço ácido. Os tubos de elevada resistência, fabricados para serviço ácido, apresentam grande desafio para a soldagem. Os consumíveis e processos devem ser capazes de produzir uma junta soldada de alta resistência, baixa dureza e elevada tenacidade. O objetivo deste estudo foi identificar problemas de amolecimento ou fragilização da ZAC e verificar se a elevada resistência não prejudica a tenacidade e dureza do metal de solda. A metodologia incluiu a soldagem circunferencial e ensaios de dureza e CTOD. Os resultados mostraram que o metal de solda e a ZAC do X65 e X70, são adequadas para o emprego em dutos terrestres. Observou-se um amolecimento na ZAC do X70 e X80 que, de acordo com a literatura, não é crítico para projetos baseados em tensão. Para o X80, o CTOD da ZAC ficou abaixo do valor mínimo desejado, indicando que pode ter ocorrido a formação de zonas frágeis localizadas e resultando na necessidade de estudos complementares para ajustar os parâmetros de soldagem. Os resultados deste estudo servem como base para uma futura aplicação destes materiais em campo.

Aug 16, 2017

By Leandro de Arruda Santos, Lorena Isabela de Oliveira Ribeiro, Jéssica Dornelas Silva, Pedro Damas Resende, João Victor Lucas Amim, Suzanny Cristina Soares Martins, Vicente Tadeu Lopes Buono

Ligas com memória de forma de NiTi são frequentemente submetidas a esforços cíclicos durante suas aplicações, o que pode acarretar em fratura por fadiga. Entretanto, o comportamento em fadiga destas ligas ainda não é completamente compreendido. Neste trabalho foi realizada uma avaliação das propriedades mecânicas de fios superelásticos, antes e após tratamento térmico, por meio de ensaios de ciclagem mecânica uniaxial após submissão a diferentes frações da vida em fadiga por flexão. O tratamento térmico foi realizado a 400°C por 30 min, seguido de resfriamento em água. As fases foram identificadas por meio de difração de raios-x e as temperaturas de transformação foram determinadas por análise calorimétrica diferencial. Os resultados obtidos mostraram que fios austeníticos apresentaram comportamento superelástico durante toda sua vida em fadiga. Entretanto, o acúmulo de danos pôde ser notado como um aumento na tensão máxima atingida durante a ciclagem mecânica após ensaios até diferentes frações da vida em fadiga. Os fios tratados, por outro lado, passaram por deformações elásticas da martensita, caracterizando comportamento similar ao de fadiga de alto ciclo de materiais convencionais. Nestes fios, as tensões máximas atingidas se estabilizaram, indicando que o acúmulo de danos é desprezível se comparada aos fios superelásticos.

Oct 31, 2019

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Carlos Gonzalo Alvarez Rosario

O presente trabalho avaliou a capacidade de degradação bacteriana de cianeto da cepa Bacillus pumilus em efluentes contaminados. Para isso foram realizados estudos de degradação bacteriana de cianeto em frascos agitados e incubados em agitador orbital durante 120 horas. Os ensaios aconteceram em três etapas; a primeira etapa consistiu na ativação e crescimento da bactéria em meio Luria Bertani, seguida da adaptação a ambientes alcalinos e por ultimo a etapa de degradação de cianeto. A proporção de inoculo foi de 1:500. Utilizou-se tampão CAPS para manter o pH alcalino. Para avaliação da degradação de cianeto foi preparada uma solução sintética contendo 500mgL-1 de cianeto de potássio pH 10. Foi avaliada a influencia da temperatura na degradação bacteriana (27, 32 e 37oC). O controle do crescimento celular foi realizado por medidas de densidade óptica com comprimento de onda ?=600nm. A quantificação do cianeto livre foi realziada por polarografia utilizando-se o analisador voltamétrico (computrace control 797 Metrohm). Dos resultados obtidos foi possível determinar que a cepa B. pumilus obteve melhor desempenho na degradação de cianeto a temperatura de 27oC conseguindo degradar 100% do cianeto livre presente na solução. O tempo empregado para a degradação total do cianeto foi de 3 dias.

Oct 30, 2017

By Tainan Ferreira Muniz

O presente trabalho estudou a influência de alguns tratamentos térmicos sobre a microestrutura e as propriedades mecânicas de um aço microligado visando à adequação de parâmetros que o classifiquem como um ao do tipo API X65 paraaplicação na prospecção e condução de óleo e gás. Diferentes ciclos de tratamentos térmicos envolvendo normalização, têmpera e revenimento foram aplicados a amostras deste aço. Estas foram submetidas a ensaios de tração, dureza Vickers e impacto Charpy, além de terem sido microestruturalmente caracterizadas com o auxílio de microscopia ótica e eletrônica de varredura. Observou-se que as microestruturas e propriedades mecânicas foram fortemente influenciadas pelos tratamentos estudados. Entretanto, apenas a amostra temperada e revenida atendeu integralmente aosrequisitos para o grau API X65no que diz respeito às propriedades mecânicas.Estaamostratambémapresentou maior a tenacidade ao impacto, o que está associado ao alívio de tensões e à decomposição da martensitae da bainita em carbonetos de ferro e ferrita. A amostra normalizada apresentou microestrutura constituída por perlita e ferrita, possuindo assim os menores limites de resistência mecânica e a maior ductilidade. Já nas espécies normalizada-temperada, assim como na simplesmente temperada, observou-semartensita e bainitacomo principais constituintes, supondo-se a presença de uma pequena fração de constituinte MA.

Aug 16, 2017

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Andrea Donadon

This article introduces the Danieli Total Asset Management System, which involves 360 degrees service methods and equipment. Danieli Condition Monitoring System and Danieli Torque Monitoring System are fundamental to evaluate the conditions of the working components in heavy duty transmissions. The first one monitors the vibrations and the lubrication fluid conditions with the purpose to identify the presence of malfunctions, by detecting any variation of the signals from the standard values. The second one monitors the transmitted torque for each spindle and gearbox, with the aim of detecting any anomaly in torque distribution and magnitude, and evaluating the residual life of the mechanical parts, on the base of a dedicated fatigue damage algorithm. All these features are useful in avoiding serious damages to machines, facilities and people, but allow also planning the maintenance and overhaul activities with efficiency, in order to achieve the best plant availability and reliability. The data analysis is made by the IntelliCMS software, which interfaces with plant and Danieli operators and includes the possibility to cooperate by remote connections, simplifying service activities and support. All these features allow providing new full service programs, where the client is totally supported in maintenance, overhauls and substitutions. This is the best way to ensure the most efficient, high quality and reliable after sales assistance.

Aug 16, 2017

By Daniele Tolazzi

In today’s highly competitive market situation, it is of outmost importance for EAF steel makers to optimise their processes in order to reduce operating costs and to improve safety and reliability of the equipment. The laser based off-gas analysis technology, With laser units installed on the fix duct, downstream the combustion gap, uses the “Tuneable Diode Laser Absorption Spectroscopy” (TDLAS). The system performs real-time off-gas emissions measurements of CO, CO2, O2, H2O and temperature. A closed-loop operation is in place for dynamic control of the chemical energy package combustion/post-combustion of CO, H2 and CH4 gases into the EAF furnace shell. A statistical framework which builds on a data analysis engine, based on Danieli Automation Q3Intelligence technology, evaluates the “fingerprint” of the process represented by average and deviation trends of both gases and other process parameters. Process fingerprinting is conceived both for offline profile optimisation and on-line control of the refining process. This paper describes how the technology has been applied and the results achieved at ACCIAIERIE BERTOLI SAFAU (Italy) 100 t AC Electric Arc Furnace.

Aug 16, 2017

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Martim Hideki Nakayama Kurauchi

One of the main issues regarding the use of charcoal in metallurgical processes is its mechanical strength, which is much lower than coke. There is no defined standard to determine charcoal compression strength, and the methods described in the literature consist in using a prepared specimen and applying compressing load in the same direction of the charcoal fibres. As charcoal is highly anisotropic, it is proposed a procedure that does not use a specimen and with load applied on a specific direction. Instead, it intends to simulate industrial conditions by randomly dumping charcoal inside a tube, without preferential directional arrangement. This is an attempt to determine charcoal mechanical strength and predict the behaviour of bulk charcoal under a static load, as in a blast furnace. Experiments with controlled loads have been carried out on randomly distributed bulk charcoal with controlled initial size and their effect on the size distribution has been analysed. After compression, charcoal is screened and each size is weighed, determining the particle size distribution of the experiment. This method can therefore be used to evaluate charcoal mechanical strength.

Aug 1, 2018

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Thomas Germershausen

Worldwide BOF-based steel plants are faced with demanding environmental requests and rising energy costs. For cleaning of primary gases from the BOF the scrubbing technology is worldwide adapted. For wet-scrubbers there is a direct relation between pressure loss and achievable clean gas dust content. Subsequently main energy consumers within Gas Cleaning Plants are the driving fans. To evaluate actual performance and to identify optimization measures extensive field measurements at existing Gas Cleaning Plants were performed. The operational results from various BOF plants worldwide will be presented and benchmarked. As a conclusion, advanced control strategies for reduced energy consumption and lower environmental impact were developed and implemented.

Jul 30, 2018

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018