Search Documents

By E. V. Konopleva, H. J. McQueen, V. M. Khlestov

In addition to increasing grain boundary area during hot working of austenite, the dislocation substructures create potential sites for nucleation of ferrite both at original grain boundaries and at transition boundaries between deformation bands. This development gives rise to a marked increase in the rates of nucleation, of growth and of transformation to ferrite. The combined net effect is product grain refinement that requires less stringent cooling between finish rolling and coiling; hence determination of the above rates would advance process optimization. The important control parameters are the preheat temperature (degree of homogenization), finishing temperature, strain (accumulation near finishing) and the extent of recrystallization after finishing. These effects vary greatly with steel composition; nevertheless, some general rules have been formulated. Moreover, there is also potential for deformation of the refined ferrite. There are other thermo-mechanical processes such as warm forming of metastable alloy austenite to provide a dense substructure that is carried into the martensite on quenching. In other processes, the austenite may be deformed during cooling through the transformation to develop a dense substructure in the ferrite that is stabilized by fine carbides.

Jan 1, 2004

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

The Bureau of Mines recognized the need for a demonstration program to distribute and apply existing information regarding the illumination of working places in mines. This report details the performance of illumination systems which were installed on several different types of mining machinery.

Jan 1, 1978

Four taconite plants were studied to establish the extent of hazard to plant personnel which exists based on long-term exposure to noise. The criteria for evaluation include the 90 dBA and 85 dBA summations of partial exposures. Data from extensive interviews were used to determine all work stations or locations which employees occupied and how much time they spent in ach location in a typical working day. Noise level measurements at every designated location were then made. By means of a computer program, these time and noise level data were us d to find the optimum noise reductions which would be required throughout each plant to meet both noise criteria. Subsequently, each plant was examined in detail so that the apparent sources of noise for each of the locations requiring noise reduction could be delineated. In tabular form, this report presents the hazardous locations for each plant, the existing noise level, the optimum noise reduction which would be required to meet the current and proposed laws, and the sources of noise which produce the existing noise level.

Jan 1, 1977

By H. H. Schrenk

The purpose of respiratory protective equipment is to prevent the inhalation of harmful or objectionable atmospheres. Although constituents or contaminants that may render an atmosphere irrespirable or objectionable are numerous, they may be classified broadly as follows: I. Gaseous substance: n. A. Toxic. B. Inert (oxygen deficiency). II. Particulate matter (dispersoids). A. Solid. a. Dust (formed by disintegration). b. Pure (formed by condensation). B. Liquid. a. Mist (formed by disintegration). b. Fog (former by condensation).

Jan 1, 1940

By G. S. Crawford

Forecasts prepared by the B.C. Research Council for the National Harbours Board suggest that mineral shipments through B.C. Lower Mainland port facilities will increase more than four-fold, from 6 to about 25 million tons, during the decade 1965 to 1975. The longer term outlook is for a six-fold increase to about 35 million tons by 1985. In 1967, minerais accounted for more than one-third of the total deep-sea traffic tonnage, nearly as much as grain. By 1975, the minerals' share will be about half the total. The principal items are exports of potash from Saskatchewan, and of coal and sulphur from Alberta and British Columbia. Additional exports include copper and other mineral concentrates and propane. Imports are chiefly salt and phosphate rock. Coastal traffic in such items as cement, sand and grave!, and limestone totalled 3.3 mil-lion tons in 1967. They will continue to be of major importance, but do not have the spectacular growth potential of the deep-sea traffic.

Jan 1, 1968

By Prince Lazarovich, Hrebelianovich

I WAS asked by the chairman of one of the Sessions on Employment Problems to talk about the viewpoint of the foreign workingman. I am not a workingman. I have never done what a work-hand might call an honest day's labor; that is, I have never been in a factory or manufacturing plant or in a mine, though in truth, hard work and I are well acquainted. I was a soldier, am an engineer, have long been actively interested in the most important waterway construction in the near East, have served politics and diplomacy, written books and lectured at universities. My knowledge of the foreign workingman in this country comes from the fact that my own compatriots here at various times came to me and appealed for advice and help, and last year I was asked by the employment manager of a corporation to undertake a welfare job at one of their plants. I went out, saw the plant, talked with the superintendent and outlined certain of my ideas which he personally heartily approved, but which did not find favor with those higher up. I approach the subject of the foreign workman's point of view with the understanding that the industrial employer's effort is for the maximum of efficiency. I am conversant with labor conditions abroad both in industry and agriculture. What I have learned of industrial conditions in America as they affect the foreign immigrant has been chiefly gathered from the cases referred to of foreign workmen who from time to time have come to me with their troubles. In the course of those investigations, in order to give whatever help or advice was possible, I have been impressed with the fact that the great United States industries evidently had- pot yet sufficiently recognized the value of studying the conditions of the workingman in the lands of his origin across the seas. A careful study of that which could be called the moral element in connection with its foreign labor would give industry a knowledge of the man's reason for coming, what' grievances he brings with him, his hopes for a future, and the peculiar character of his capacities. The employer would thereby be enabled to meet the man, to be helpful to him, to aid him and at the same time promote industrial efficiency, inasmuch as a workman who believes that he is being dealt with humanly and squarely is contented and satisfied and will give willingly, and even with pride, the best that is in him; justice and a fair deal is all the man wants.

Jan 4, 1918

By Richard H. Spencer

The purpose of this program was threefold: (1) to identify the symptoms of poor or inadequate performance of trolley carrier phone systems; (2) to assess the root causes of performance difficulties and classify them on the basis of equipment, coupling, or transmission; (3) to propose, analyze, test, evaluate and verify means of overcoming performance difficulties. Based on interviews and discussions with knowledgeable persons, laboratory experiments, and in-mine measurements, it was determined that the major impediment to good carrier phone system performance is the extreme signal attenuation found on the trolley wire/rail largely due to the many bridging loads. Three means are identified to help overcome the performance difficulties: the low impedance trolley wire, a method of improving performance by capacitively loading the transmission line; the dedicated wire, a low-loss means of extending trolley signal coverage; the use of isolators to remove the offending bridging loads at the carrier frequency. Other subjects treated in the report are design reviews of hardware, guidelines for the use of information in the report, recommendations, and a description of a probe for measuring trolley wire current.

Jan 1, 1977

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By Franco Oboni, Iain G. Bruce

The design of tailings containment structures relies on well-understood engineering methods being applied consistently. Unfortunately, not all facilities are designed or managed to the same level of competency. To standardize procedures, the Mining Association of Canada (MAC, 1998) prepared a “Guide to Tailings Management.” It recommended review of designs and an assessment of the risks associated with tailings impoundments be implemented during all phases of amine life. This paper describes how the quantitative risk assessment (QRA) process can be used to define risks associated with the design, construction and operation of a tailings management facility. And it discusses how, once the risk tolerability curves (RTC) are defined for a project, they can assist the risk management (RM) process.

Jan 1, 2002

By Donald Bruce

The three types of specifications which are used for micropile work are: ? Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. ? Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. ? Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications. Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.

Jan 1, 2004

By R. W. Smith

Living and killed organisms, particularly microorganisms, and extracellular products derived from the organisms are increasingly finding use in minerals engineering. Goals include both enhancement of mineral processing/11.ydrometallurgica,l operations and remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of ?sulfide ores and bioxidation of refractory gold ores, are well established commercial ?processes used around the world. Others, such as the use. of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Many other uses of microorganisms and. their derivatives are potentially possible. These include use of microorganisms in flocculation or flotation of minerals., remediation of organics potentially discharged from mineral engineering operations, degradation of cyanide, the recovery of bitumen from heavy oil reservoirs and tar sands and the solubilisation of lignites and low rank coals. In order to fully exploit these many possible uses of organisms and their derivatives, extensive fundamental .and .applied research work exploring the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering should be vigorously pursued. ?

Jan 1, 1991

By Joint Micropiles Committee

"The three types of specifications which are used for micropile work are: • Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. • Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. • Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications.Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.The owner, designer and contractor will together be responsible for the tasks associated with the design, installation, acceptance, and performance of the micropiles. The installation of micropiles requires specialized equipment, techniques, and appropriate workmanship. Not every detail of the work can be specified, and not every potential problem can be anticipated. Therefore, a contractor who has demonstrated experience in micropiles must be selected to execute the work required."

Jan 1, 2004

For the third successive year it appears that demand for platinum will exceed supplies of newly-mined metal, forecasts Johnson Matthey in its "Platinum 1987 Interim Review." Based on data available at the end of August 1987, Johnson Matthey estimates that western world demand for platinum could exceed 93t (3 million oz) for the first time ever in 1987. Given a likely increase in demand of 4.3t to around 94t (140,000 oz to around 3.02 million oz), up by about 5% over 1986, there would be a 1.8- to 2.2-t (60,000- to 70,000-oz) shortfall in 1987 supply. South African mines enjoying undisrupted production last year after strikes affected Impala's output in 1986. The rate of increases in western world supplies, though, has probably not kept pace with the growth in demand. A downturn in US demand for platinum was counterbalanced by substantially increased purchases from Japanese and Western European consumers of the metal. Total imports of platinum into Japan in 1987 may have reached a record level of 45t (1.45 million oz). The largest source of demand for platinum remains its use in autocatalysts US and Japanese auto manufacturers reduced their platinum purchases in the wake of falling car production. Therefore, a small decline in overall 1987 sales of perhaps 780 kt (25,000 oz) was expected in 1987. Western European demand, however, rose strongly as a result of increased output. The spread of exhaust emission control regulations has sharply boosted the number of cars equipped with three-way catalysts containing platinum and rhodium. Western European auto makers probably needed 5.6t (180,000 oz) of platinum last year, a 50% increase over 1986. The jewelry industry, the second largest user of platinum, increased its offtake of platinum in 1987. Japan, the key to the jewelry industry's consumption of platinum, could absorb 24.8 to 26.4 (800,000 to 850,000 oz) in 1987, compared with 23t (740,000 oz) in 1986. Platinum has wide and diverse applications in industry. Other major users are the chemical, glass, electronics and petroleum industries. They were expected to increase their aggregate demand by about 1.8t (60,000 oz), or 11% in 1987. Investment demand for small platinum bars and coins of up to 311g (10 oz) dropped back in relatively inhospitable conditions. This, after rapid increases in recent years and a surge in US demand in 1986. However, Japanese investors purchasing bars weighing 500g or 1 kg (16 to 32 oz), and considered more speculative, recovered last year. Over the first eight months of 1987, platinum performed strongly on the open market with average prices well up from 1986 in dollar terms. But the increase was less marked where measured in sterling or yen. Platinum ad¬vanced by $3.70/g ($115 per oz) between Jan. 1 and mid-September with the average price having been surpassed only in the heady days of 1980. Johnson Matthey believes that supply and demand appear likely to keep more or less in step on a gently rising path. The recent open market volatility will continue with prices fluctuating widely over short periods. Writing in mid-September, and basing its view on the tangible evidence of platinum's price fall since the review was written, the company's assessment of price prospects is unchanged. Demand for platinum remains strong all-round. In October, imports of platinum into Japan were exceptionally high. And in the US and Japan there was a marked resurgence of demand from private investors. Although market sentiment may have been influenced in part by the news of several potential new platinum mines in South Africa, the full effects of these prospects on supply, even if they were all to materialize, would not be felt before the early-mid 1990s, Johnson Matthey said. According to the review, no radical change in platinum supplies is discernible in the near-term. Incremental growth from South Africa can be expected as the major producers continue to make the most of their existing resources. The Soviet Union may be keener to sell than it appeared earlier in 1987, especially if prices hold up, but a substantial increase is improbable. Canadian supplies are not capable of much variation from present levels. The palladium-rich Stillwater mine will make a modest contribution. Referring to the investment market, Johnson Matthey concluded that despite this year's reduction in sales of small-denomination investment products, platinum does appear to have established itself with private investors. Bearing in mind how business multiplied in comparatively unfavorable conditions before 1986, it is reasonable to look for a resumption of growth once the climate improves.

Jan 2, 1988

By T. Holmes, J. Middlemiss

"Agnico-Eagle (AE) has been operating their Kittila Mine in Northern Finland since 2008. The mine has experienced considerable ore flow problems with ratholing, bridging and freezing in their mill feed bin since start up. In the first winter of operation, the entire central portion of the contents of the cylindrical flat-bottomed 2000 tonne mill feed bin froze. Flow was erratic and could only be achieved through small diameter ratholes. To maintain a reasonable, albeit limited, feed to the mill, the bin had to be kept less than ½ full and a portable steam generator was brought in to melt the frozen agglomerates that frequently blocked the outlets. The combination of limited surge capacity and frequent outages required the crushing plant to operate 24/7 and resulted in inconsistent production levels and high operating costs.AE had planned to expand the processing plant to increase throughput by about 30% when they transitioned from open pit to underground ore. These plans presented an opportunity to improve the material handling.To avoid the problems experienced with the original mill feed bin, AE enlisted Jenike & Johanson Ltd. (J&J) to test samples of the ore, and based on the measured flow properties to provide design recommendations to ensure that the new mill feed bin would operate reliably. The new 2000 tonne expanded flow mill feed bin and apron feeder were installed in 2014 and are now supplying almost 93% of the total mill feed with the remaining coming from the original bin.IntroductionIn early 2009, AE engaged J&J to visit their then recently opened Kittila mine and mill in Northern Finland (Figure 1). Over the first half-year of operation, production had been restricted in the ore handling and storage system by flow problems such as ratholing, bridging and freezing including blockages of chutes and hoppers as a result of frozen fines buildup and large frozen agglomerates. AE wanted to increase production in the existing open pit mine and mill feed operation and also wanted to avoid similar ore handling problems when they commissioned the new underground mining system under development at that time."

Jan 1, 2017

By R. Marleau, R. Assad, J. Dugas

"A study of the geological features of known occurrences of mineralization in Gaspe is the basis for a classification. Nickel, chromite, asbestos and some copper are pre-or syn-Taconic, whereas the most important deposits are tied to granitic post-Taconic stocks. Most occurrences are clearly related to igneous rocks: nickel, chromium and asbestos to Ordovician serpentinite; copper to volcanic rocks of different ages; and copper, zinc and lead to acidic intrusions with apparent zoning. Some lead-zinc deposits lying between the Grande Greve and York Lake formations are stratigraphically controlled. Some occurrences are tied to faults; e.g., the nickel-copper mineralization along the North Grand Pabos fault. Northerly-trending transverse structures appear to coincide with the Gaspe Copper, Mount McGerrigle (Tabletop) granite and Lemieux dome areas of mineralization. JEAN DUGAS, after graduating"

Jan 1, 1969

By J. D. Davis

THIS-report gives results of in investigation of the carbonizing properties of 18 coals, including 2 from Alaska, 12 from British Columbia, 3 from Washington, and 1 from Utah. Each coal was carbonized in the standard 13-inch Bureau of Mines-American Gas Association (BM-AGA) retort at 900° C. Plastic properties were determined by the Gieseler and Davis methods, and agglutinating and free-swelling properties were determined by standard methods. Expanding properties were measured in the Bureau of Mines sole-heated oven. From the results of the tests on these single coals, three coals from the Crowsnest area in British Columbia, representing Elk River Nos. 4, 9, and 10, were selected for blending with the Utah coal, which was from the Lower Sunnyside bed, Horse Canyon mine, Emery County. Lower Sunnyside also was blended with Wilkeson -Nos. 2 and 3 (Washington) coals, Pocahontas No. 3 from McDowell County, W. Va., and the Oklahoma low-volatile coal used in the blend carbonized at, the Provo, (Utah) coke plant at the time this investigation was started. Most of the blends contained 3 percent hard pitch, which is the proportion used at the Provo plant. The blends were also carbonized in 13-inch BM AGA retorts at 900° C. High-volatile B coal from the No. 3 bed, Evan-Jones mine, Lower Matanuska, Valley, Alaska, yielded poorly fused coke or char. M-bed coal from the Chickaloon mine, Upper Matanuska. Valley, Alaska, ranked as medium-volatile bituminous and coked strongly. It expanded 39.6 percent in the sole-heated oven at a. charge density of 55.5 pounds per cubic foot..

Jan 1, 1952

By R. W. Bruhn

The objective of the study is to examine the apparent influence of soil and near surface rock strata on the severity of damage experienced by surface structures subjected to mine subsidence. The report discusses: 1) modes of ground movement that might complicate or be confused with mine subsidence; 2) prevailing concepts concerning mine subsidence in the Northern Appalachian Coal Field and Illinois Basin; 3) apparent influences of soil and near surface rock strata on the character of subsidence-related ground movements; 4) classifications and criteria for characterizing damage due to ground movements; and 5) types of subsidence damage experienced by homes above active mines in western Pennsylvania. Presented is a damage classification system incorporating a severity index for characterizing subsidence damage to homes with basements above active mines. A series of case histories illustrate subsidence damage to structures above active and abandoned mines.

Jan 1, 1983

By M. H. Attia

The concept of sustainable development has been evolved into a working framework for sustainable manufacturing, in which the environmental requirements are introduced into product development at the design stage. This keynote paper is discussing a number of issues pertaining to the impact of manufacturing on the environment. The conflicting requirements of sustainable development, sustainable manufacturing (SM) and economical growth are presented in the light of successful case studies that were able to convert conflicts into opportunities. Integration of SM into the product life cycle is also presented. A number of concepts that are related to Ecoefficiency, e.g., inverse manufacturing, demanufacturing and re-manufacturing are also discussed. The paper underlines the fact that the positive impact of this new philosophy is equally applicable and beneficial to both; developed and developing countries. The paper concludes with an overview of Global trends in environmentally benign manufacturing (EBM); e.g., product-take back and emerging material and processing technologies. The state-of-the-art approach to Life Cycle Impact Assessment and integration of design for the environment DfE principles are demonstrated through some case study.

Jan 1, 2006

By Carlos Alberto Sanchéz

El presente trabajo describe la realización del monitoreo de zonas revegetadas de cierre de minas utilizando técnicas de teledetección espacial. El estudio evaluó las áreas iniciales del programa de revegetación final de la minera Yanacocha. Las áreas de estudio son Maqui Maqui y San José, se localizan en la zona este de operaciones y se encuentran en cierre desde el año 200 y son restauradas dentro del programa de revegetación de áreas finales de la empresa. Como parte de la medición del éxito del programa se realiza el monitoreo de las mismas utilizando estas nuevas tecnologías. Por ello, es aplicable como parte de la conducción de los programas de revegetación de los planes de cierre de minas.

Sep 12, 2005