Search Documents

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By E. I. Robinsky

"This paper describes a new, proven approach for tailing disposal. Not only is the disclosed system less damaging to the environment, it is also less costly to operate, to close down and maintain in perpetuity. The basic concept is to discharge thickened tailing from one permanent location.This creates a conical or hill-like deposit which:(1) requires lower perimeter dykes for equivalent storage capacity;(2) eliminates decant towers and decant lines;(3) requires no steep dams built of tailing;(4) is stable:(5) requires only a small pond outside the deposit;(6) decreases pollution of the surrounding environment by water seepage and deflation; and(7) simplifies abandonment and ""closing-down"" operations.The approach is made possible by the fact that, at a sufficiently high ratio of solids to water, tailing material can be made to accumulate at slopes of 5 or 6 per cent -- considerably steeper than possible by traditional methods using low solids-to-water ratios. To achieve the necessary solids-water ratio (35 to 60 per cent), it may be necessary to install a thickener. It is expected, however, that at many concentrators it may be possible to discharqe relatively clear plant water through a line separate from the tailing line, thus reducing the load on the thickener."

Jan 1, 1976

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010

By Colin Curtis

In recent years, Manchester Airport has undergone expansion including the construction of a second runway, a new terminal building (Terminal 3) and extensions to the existing Terminal 1. Manchester is Britains third largest airport and ranked 20th in the world for international traffic. Arup (Manchester) was engaged as consulting engineer in a multi-disciplinary role for the terminal works. Part of this was a geotechnical commission including site investigation and pile design followed by supervision. This paper reviews the piling for the old, new and terminal extensions. In total, five pile types have been utilised over the years. The original 1950's Terminal 1 was founded on driven cast in situ piles, with a later 1970's extension utilising rotary augured piles. The recent piling comprised continuous flight auger piles (CFA), driven steel tube and tripod bored; the latter in areas of restricted access or low headroom. The ground conditions are Made Ground over thin Alluvial and Glacial drift, in turn, over a generally weak to moderately weak gypsiferous mudstone. All the piles were socketed into the mudstone. In terms of the new CFA piles, quality control using the instrumentation monitoring was problematical, but a substantial static load and integrity test programme resolved pile performance. Part of the work is matching new pile performance with previously installed piles and the continued use of older piles with new loads. Research provided some data on the older piles, including some static load test data, which enabled back analyses of their design and likely behaviour. Differences in design methods, installation techniques and pile behaviour based on load tests will be discussed.

Jan 1, 2001

By Tamara Whitaker, James Gunderson, Ruilin Yang

This paper presents the results of a vibration control project conducted in soft overburden at a surface coal mine located in the western United States. The study uses near-field blast vibration monitoring, analysis and modeling techniques developed in house. Accelerometer-equipped seismographs were utilized for near-field vibration monitoring and analysis. Vibration control was achieved through field data regression as well as vibration modeling using the multiple seed near-field blast vibration model (Yang and Scovira, 2007). The regression was conducted between peak particle vibration parameters and the minimum scaled distance per delay. From the regression analysis, the curves of upper bounds for peak particle vibration parameters and charge weight were developed. The dominant frequencies of the blast vibration were also addressed in this project. The regression curves and near-field vibration model guided the blast design to control blast vibration for maximizing the recovery of coal and maintaining mine productivity.

Jan 1, 2008

By D. R. Cook

This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. The project was based on the idea of W. S. Burbank, U. S. Geological Survey, that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Here, an area of andesitic rocks, four square miles in extent, has been argillized, pyritized, chloritized and silicified. Geological, geophysical and geochemical studies were followed by the diamond drilling of three holes totalling 6,220 feet. Further alteration ang geochemical studies were made on the cores from these holes. A brief review of the alteration and geologic mapping, colored aerial photograph interpretation, geochemical soil and rock sampling, magnetic, gravity and radio-metric surveys are presented together with some conclusions regarding this work. This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. Important contributions were made to the project by personnel of the Rocky Mountain District and the Geophysics Division. Individual acknowledgements to these people are made at the end of the paper. BASIS FOR THE PROJECT The project was based on the idea of W. S. Burbank (1947, p. 444) that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Paleozoic sedimentary rocks, including the favorable Leadville limestone, are exposed three miles south of the altered area, and reason exists to believe that they might underlie it within a reasonable depth. Alteration of pre-mineral volcanic rocks has been used successfully as a guide to concealed orebodies in the Main Tintic and East Tin tic mining districts, Utah (Bill-ingsley, 1933, p. 120-122; Lovering et al, 1949; Howd, 1957, p. 124-134; Cook, 1957, p. 73) and could be a useful guide here. GENERAL GEOLOGY AND STRUCTURE The Northern and Southern Bonanza mining districts are northwest of the San Luis Valley in southern Colorado, just within the northeastern edge of the San Juan volcanic province. The districts are1ocated on the southern extension of the Sawatch uplift, a prorninent northwest-trending structural high. The highly productive mining camp. of Leadville, Gilman and Aspen are on the northeastern and northwestern flanks of this uplift where Paleozoic limestones have

Jan 1, 1961

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By Miklos D. G. Salamon

If all stratifications are horizontal, the computation of surface deformation induced by coal mining involves the prediction of roof and floor convergence and then the transfer of the effects of this relative displacement to the surface through the use of the appropriate influence functions. A laminated model, in the form of a quasi- continuum, provides a simple means of computing the approximate convergence distribution and leads to the Gaussian distribution as the influence function. The ideas presented in this paper represent a subtle but fundamental generalization of the influence function Method. It is postulated that the influence of a small area of extraction is proportional to the roof and floor convergence and not to the thickness extracted. This difference in definition removes many conceptual difficulties associated with the influence function method. To demonstrate the utility of the model, the surface disturbances induced by the extraction of a parallel sided long panel are derived. Formulae giving subsidence, tilt, horizontal displacement and strain are given.

Jan 1, 1989

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

THE Phillips River gold and 'copper field is situated on the south coast of Western Australia, about 200 miles east of Albany, 180 miles west of Esperance, and: 250 miles south of Southern Cross, forming the southern extremity of what Mr. H. P. Woodward classes as the fourth belt of Pre-Cambrian rocks, and the first auriferous belt, whicf extends northward through Southern Cross, Mount Magnet, and Cue. The field may be considered the premier copper producer of the State. The first mineral discoveries were made about 1892; when gold, copper, and iron pyrites were found; but, owing to the isolation of the district and the scarcity of water, both in the locality and on the route thereto, little work was done for some years. In1899, however, payable gold reefs were opened up, and the district began to attract attention.The southern portion of the district is composed of limestone and sandstone rocks, forming the coastal series, and is for the most part flat, broken only by a few low hills and ridges, except to the west, where Cape Barren and Eyre's Range stand out...

Jan 1, 1917

The usual metallurgical, engineering and administrative activities associated with the handling and smelting of ores, and the subsequent handling and treatment of the products of smelting, present also problems of hygiene that engage the earnest attention of executives in all well-managed concerns.Again, associated with the employment of any considerable number of men, there is always present the problem of accident prevention.INDUSTRIAL HYGIENE.In the earliest records of lead min.ing and smelting there are references to the injurious effects of lead oh the health of the employees, and, with the advancement of medical science, lead poisoning has been the subject of many works by various authorities in many countries.Moreover, in practically every civilised country, there are laws governing the conduct of the lead industry, and in most cases these laws stipulate that employees shall receive compensation for disability caused by lead poisoning.This provision gives the problem an economic aspect. Apart from the legal and the economic aspects, however, there is the humanitarian aspect, which implies that the...

Jan 1, 1937

A general outline of the significant features in the quality and manufacture of the more common refractories is given. Where possible, linkage between quality development and control and service applicationhas been shown and explained. INTRODUCTIONThe refractory industry is no stranger to change. New processes and revision of old processes in other industries are the harbinger of new and revised products in refractories.Few of the changes are dramatic; generally they are evolutionary rather than revolutionary. New developments are additional to, and inclusive of, established practice.Therefore in this paper it is necessary to repeat much of what is already known in order to show the development taking place.FIRECLAY REFRACTORIESGeneral technology Fireclay refractories are the most common, the most varied and the most versatile of all refractories. Virtually any composition of silica and alumina up to the composition of kaolin is possible. For purposes of comparison they may be classified in the Continental fashion in accordance with chemical composition or in the American way according to "duty". That the two methods are equivalent is shown by an inspection of the alumina-silica diagram of Bbwen and Greig (1924). 'Fireclay refractories are composed of a glassy and a crystalline component derived from the chemical and physical nature of the raw materials used in their manufacture.

Jan 1, 1961

By Sverre Olsen, Kai Tang

The composition of ferromanganese slag is very important as it determines the slag/metal equilibrium relations including MnO content of final slag, melting relations and slag viscosity. The slag composition is further expected to influence the process temperature. The properties of ferromanganese slags are suitably described by its basicity and A/S mass ratios. The influence of slag basicity has been discussed in the previous papers. The present paper will discuss the effect of Al2O3 on melting relations, viscosity and MnO-content of final slag. This discussion will be based on assessed thermochemical databases and a recently developed viscosity model.

Jan 1, 2007

By M. N. Brodie

"The ability to adjust the speed of a SAG mill offers benefits to the process and to equipment maintenance. It can be provided with some slight effect on availability ranging from somewhat enhanced to somewhat reduced, depending on the particular equipment that is used. Several techniques have been developed for monitoring the magnitude of the contained charge, and several algorithms have been used to control mill feed rate and mill speed. The various benefits and the means by which they can be realized are examined and compared. Reasons for Variable SpeedProcess RequirementsThe recovery of minerals from ore is dependent on particle size and residence time in process. Separation in a given plant is most efficient at a particular rate and a particular size (e.g., 80% minus 200 mesh). If the particle size increases, less mineral will be liberated. If the particle size is significantly reduced, the process of choice may not be able to effect separation, and power, media, and maintenance costs would be increased.If a SAG mill-ball mill combination delivers the desired throughput at the correct size for efficient separation when processing ore of the design hardness, some adjustment must be made to maintain this condition when the ore changes. The processing of ore softer than design will result in overgrinding, unless:• the throughput is increased inversely to the change in hardness which lowers recovery by overloading the separation facilities;• or the SAG mill feed rate remains constant, but the speed is reduced to feed coarser material to the ball mill for finish grinding to the desired size.There is also the effect of changing milldiameter to consider. A nominal 36 ft diameter SAG mill will have an effective diameter of 35 ft with new liners and 35 ft 6 in. with worn liners. A mill designed to operate at 0.76 p.u. (per unit) of critical speed with new liners (9.84 rpm) will be changed to 0.765 p.u. with worn liners. If 0.76 p.u. is the desired value, the mill speed should be reduced to 9.77 rpm."

Jan 1, 2003

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries. The typical converting operation involves lateral purging of air into molten matte through a bank of tuyeres. This blowing operation occurs at low pressure from the blowers, resulting in a bubbling regime that is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks also include recurrent tuyere blockage, tuyere punching, and low oxygen efficiency.Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to industrialscale tests, a numerical assessment to ascertain the feasibility of implementing sonic injection into a PSC was conducted. The work included flow characterization at high-pressure injection achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid method together with the RKE turbulence model to account for the multiphase and turbulent nature of the flow.This paper discusses the key findings in understanding plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a full-scale implementation of sonic injection in the smelter."

Jan 1, 2015

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.