Search Documents

By Kym Runge, Emmy Manlapig

"The objective of an industrial flotation circuit is to separate valuable minerals from non-valuable minerals utilising differences in their flotation recovery rate. Regrinding and reagent addition are particle modification processes which are employed within these circuits to maximise the flotation selectivity of one mineral with respect to the others present in the ore feeding the process.Batch test nodal analysis, or the ability to compare floatability through mathematical combination of laboratory batch flotation test results, is a powerful technique for assessing the effectiveness of particle modification processes on ore floatability in industrial flotation circuits.In this paper, the use of nodal analysis is demonstrated within an industrial flotation circuit. It is used to show that regrinding and staged reagent addition within Teck Cominco’s Red Dog zinc retreatment circuit is beneficial to pulp flotation selectivity. Optimisation of these processes could potentially improve the zinc recovery within the circuit. Lime addition, which is periodically employed to depress pyrite in the circuit, was found to depress sphalerite in preference to pyrite and to result in poorer metallurgical performance in the circuit.INTRODUCTIONThe objective of an industrial flotation circuit is to separate valuable minerals from non-valuable minerals utilising differences in their flotation recovery rate.Different minerals can only be effectively separated using flotation if they are sufficiently liberated from each other (i.e. do not co-exist within the same particles) and have a sufficient difference in surface hydrophobicity. Size reduction processes and chemical addition are utilised before and within a flotation circuit to achieve sufficient particle liberation and to maximise differences in mineral hydrophobicity. In effect, the objective of these processes is to maximise the flotation selectivity of one mineral with respect to the others present in the ore feeding the process."

Jan 1, 2004

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

By A. V. Shroff

The Indian Standards code of practice for design and construction of underreamed piles contains provision for installing such piles in expasive soils. In recent years, a large amount of research work has been carried out in the analysis, design, construction and performance of underreamed piles in expansive soils. This paper suggests that the results of this research field tests should be included in the code. Various additions and modifications as well as deletions that should be incorporated in the code are discussed.

Jan 1, 1996

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff' first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By Valentín Pamo Caytano

La electrorefinación en un electrolito de CuSO4 - H2SO4 es usado universalmente para producir cobre de alta pureza a partir de los ánodos impuros. Aunque una parte de las impurezas se disuelve durante la electrorrefinación y se concentra en el electrolito, otros elementos son insolubles y se acumulan como lodos anódicos en las celdas de refinación. Las impurezas deben ser removidas del cobre para cumplir las especificaciones del mercado sobre la ductibilidad y conductividad y para recuperar los sub-productos valiosos como el oro y la plata. En ese sentido, el presente trabajo describe los equipos y procesos que permiten la recuperación del oro refinado en la planta de metales preciosos de la Refinaría de cobre de Ilo.

Sep 12, 2011

By Rita D. Sylvester

THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to "disseminate information concerning these subjects 'in such manner as will best carry out the purposes of this Act.'" In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It, supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960,4 from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963.7 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction.

Jan 1, 2007

By Gary Anderson

??Privately Held Corporation ??Incorporated in Delaware, May of 2002 ??HQ in Malvern, PA (just outside Philly) ??Approx 40 employees ?9 Field Engineers ?MSHA Certified ?10 Development/NOC Engineers ?Site Survey/Site Design ?RF Engineers ??Standards Based ?IEEE 802.11 ??Commercial Off the Shelf (COTS) ?Gateworks, Ubiquity, Atheros, Linux Based ??Technology was developed and inspired by the lack of communications during the terrorist attacks of Sept. 11, 2001

May 1, 2009

Antimony ore samples (mean assay 18·7 per cent antimony) from Endeavour Inlet, Marlborough Sounds New Zealand, were tested for upgrading by flotation to a saleable product (60 per cent antimony).The effects of activating agents, collectors, frothers, pH, conditioning time, and particle size on the recovery and grade of a stibnite flotation concentrate were determined using HaIlimond tube and laboratory flotationcell test apparatus. Optimum flotation conditions for the ore were thereby established. A stibnite concentrate grading 63 per cent antimony and an overall recovery of 90 per cent is obtainable in a two-stage process.

Jan 1, 1977

By Charles A. Bankston, John C. Rowley, Robert J. Hanold, Joseph W. Neudecker

The basic concepts and processes of soil and rock melting as applied to excavation technology are reviewed. The electrically heated, small diameter prototype penetrator development sequence is presented. Emphasis is placed on the different methods of handling the fluid rock and soil melts and their significance in providing new solutions in hole support and debris handling problems. The refractory materials requirements, penetrator life and electrical heater technology are presented. Consolidating penetrators, which form stable glass-lined holes in low density rocks and soils, require no debris removal and will find applications in horizontal holes for utilities, cables, and pipeline installations. Extruding penetrators are being developed to make holes in dense, hard rocks. Melt is conditioned into a variety of debris forms, i.e., glass rods, pellets or rock wool, selected to match appropriate debris handling systems. Unique use in drilling into very hot rock or magma for geothermal exploration or production wells is projected. Some of the results of laboratory and field tests of these devices are compared with theoretically derived operating performance. Coring-consolidating penetrators for geological sampling in alluvium are projected to larger diameter self-propelled and guided coring devices for prospecting along proposed tunnel alignments. Application to the melting of annular shafts for pipeline support piles in difficult conditions such as permafrost has been scoped. Conceptual design studies of large diameter tunneling equipment have indicated the system contributions and economic aspects of rock melting relative to material comminution, wall and roof support and materials handling.

Jan 1, 1974

By Allan Sylvester, Paul E. Gabryszak, Diane R. Hirsch, David P. Field

With construction of the first phase of the Automated People Mover (APM) Tunnels nearing completion, this paper will address how knowledge from recent Tunnel Boring Machine (TBM) and New Austrian Tunneling Method (NATM) tunnel construction at the airport was used to refine the methodology for the next phase of tunnels currently in design. The benefits include an enhanced understanding of the ground conditions; allowing optimization of excavation sequences and support requirements; a more effective instrumentation and monitoring program; and improved construction details and related contract provisions.

Jan 1, 2007

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By C. D. Hebert, M. R. King

The 56,000' (17 km) long San Vicente Aqueduct Pipeline tunnel is being constructed using precast concrete rings to act as preliminary ground support through two sections of the bored tunnel with lengths of 9,450' (2.9 km) and 33,700' (10.27 km).The six segment bolted trapezoidal ring was manufactured using a combination of steel fiber reinforced concrete and self compacting concrete in vertical moulds. This paper briefly describes the design and function of the segments, and reviews the development stages of the concrete mix, and the advantages and disadvantages of the adopted manufacturing method.

Jan 1, 2007

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989

By Hebert Arias, Christian Mendoza, Mervin Tapia

El Complejo Pasco —ubicado en la Cordillera Oriental de los Andes de la sierra central del Perú, en el distrito de San Francisco de Asís, provincia y departamento de Pasco— está constituido por las unidades subterráneas de Atacocha y Porvenir, la operación a tajo abierto Glory Hole y tres proyectos brownfield ubicados en la periferia de la concesión. Tanto Atacocha como Porvenir son depósitos tipo skarn, con mineralización distal de Zn y Pb(+/-Au) y proximal de Zn+/-Cu, asociados a cuerpos hipoabisales de composición cuarzoandesítica y andesítica. Estudios y exploraciones recientes muestran otros tipos de sistemas mineralizados, como brechas tectónicas con reactivación hidrotermal tardía, un sistema epitermal de sulfuración intermedia en vetas, cuerpos irregulares, entre otros, y un sistema tipo pórfido. La Falla Milpo-Atacocha, de rumbo N-S, juega un rol importante, ya que los intrusivos (Stock Milpo y Santa Bárbara) que generan la mineralización del tipo skarn están controlados por esta falla. Existe otro tipo de mineralización, asociado al sistema NW-SE (Falla 13): un sistema epitermal de sulfuración intermedia. Este trabajo pretende mostrar los últimos avances en las interpretaciones metalogenéticas, producto de un intenso programa de exploración (aproximadamente 80,000 m. DDH / 2018) y de un programa de recategorización de recursos (a través de 60,000 m. DDH), que permitirá hacer posible una operación sostenible de 12 años.

May 22, 2019

By C. Schuffeneger

"The design of SAG milling circuits for mining projects requires the incorporation of the energy consumption considerations and the evaluation between different flexibility-adding options to absorb the time-dependent variation in the ore lithology. In order to expand the focus of the engineering design, a higher level of deepness and quality in the baseline information must be achieved to elucidate all of the constraints on throughput, energy consumption and product quality generating a design optimization consistent with an integrated vision of the process. This paper presents a review of a collection of typical examples of the copper and gold mining project in the Chilean Andes, in which both process and energy efficiency criteria are considered when the focus is to deliver an integral solution that incorporate those areas in the design. The intensive use of energy in the SAG milling, the process continuity and the quality of the product are a function of the proper design and selection of grinding equipment and plant layout, aligned with the mining plan and associated with projected future expansions and production increases.INTRODUCTION Autogenous and Semiautogenous grinding technology, large diameter and short length mills, begins with the Handsel design. During the decade of 1930’s, Handsel-Hardinge studies led to cascade mill development. Nowadays, 80 years later, continuous improvements in design and technology have been conducted to a completely new generation of gearless SAG mills that have led to an increasing capacity at the concentrator plants. Considering the existing alternatives, SAG mills are the most implemented option for the grinding circuit today. This work presents a review of the SAG mill implementation parameters and circuit considerations and its correlations in the most recent projects in Chile with an ore treatment capacity above 50 ktpd since the decade of the 90’s up to now. From this period, the tendencies will be analyzed using project design data. Based on process design information, the recent SAG mill history in relevant projects related to the new generation of commercial SAG mills, technical associated considerations and performance will be discussed. Circuit selection based on energy utilization will be revised to bring up a more holistic perspective on the SAG mill circuit design concepts. As is now well known, the heart of every concentrator plant are the grinding mills. Higher demands on throughput, availability and power consumption optimizations require not only high performance electrical equipment but also a well selected grinding circuit. The energy efficiency issues associated to the circuits design will be reviewed."

Jan 1, 2012

The Wongawilli system of mining has been in use for over 30 years and has enabled high production rates and acceptable extraction ratios to be achieved in seams less than 4 m in thickness. A modification of the Wongawilli system has been developed to permit the use of a continuous miner and mobile equipment to extract a coal seam 6 m thick. Following physical and mathematical model studies the new mining method is now undergoing field trials at Collinsville, Queensland. Progress of the field trials to date has achieved 99 per cent extraction of the upper slice by remote control operation of the continuous miner and established the feasibility of installing resin grouted wooden dowels in the coal floor to reinforce the coal septum. The method is explained in the text. Monitoring of the goaf gases as an early indication of spontaneous combustion has been incorporated in the mining cycle by placement of tubes in the goaf as the face retreats and continuous analysis of the goaf gases made at the surface by the National Coal Board tube bundle monitoring system.

Jan 1, 1980