Search Documents

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By Kennedy G. L

Experience is reporled in the operation of the pilot Lurgi carbonization plant at Morwell, afler it had been reconstructed to obtain better control of the heating of the briquettes in order to produce a strong char suitable for use as a metallurgical fuel. The theoretical Ideal Heating Cycle, which had been designed from earlier laboratory research, was closely approached in the carbonizer, and up to 97 per cent of the whole dried briquettes entering the carbonizer were recovered unbroken in the char.The strength of the char produced in the pilot plant was limited by the performance of the drier where the cracking and breakage of the briquettes was more severe. Theoretical studies have indicated that this limitation could be removed by using a hot briquette feed to the pilot plant. Experience indicates that with a hot briquette feed to the drier and with ideal heating in the carbonizer, hard char could be produced from Yallourn briquettes in continuous operation.The project has been terminated for economic reasons...

Jan 1, 1966

By Hou Shitao

With the development of Wuhan's city planning in China, new buildings of moderate and high store have been increasing day by day. Precast concrete piles or cast-in-site piles were used in the major foundations of the buildings. In process of their design and construction geotechnical engineers are concerned very much about practical bearing capacity and construction quality of pile foundations. In order to grasp accurately the cases static loading or vibration test is used generally to judge them. At present, the major questions in existence are that although a load is applied directly on pile and measured datums are reliable for static loading test, it must take a lot of work and longer time and engineering cost is higher. A vibration test has the advantages of which checking up of pile quality can be performed rapidly, the test is simple and convenient, and scope measured wide. But bigger error exists generally in measured datums. Therefore, it is nesessary to make vibration test on piles more perfect for pile foundation engineering. It is stated in paper that adapted technique of vibration test on piles is quite right in developmental direction sense for pile foundation. There are a great variety of vibration test methods on piles. A few of methods which often are adapted in practice can not meet the need of different practical engineering. It is also an important question whether the instruments of vibration test and relevant computer softewares make a response accurately for practical case. Different sequence of operation and technical requirements comes into being some influence directly on the test results. Meanwhile, different combination of soil stratigraphy, soil texture, groundwater and pile could cause different error of test datum. It is necessary to analyse and judge objectively the results of vibration test. Therefore, on the basis of developing and perfecting further the technique of vibration test, the applied technique of vibration test should be standardized so that better test results can be obtained.

Jan 1, 1991

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had its peak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By S. J. Lötter, J. T. Nel, W. Purcell

"SynopsisGlow discharge optical emission spectroscopy (GD-OES) is an analytical technique used in the analysis of solid, conducting materials. Though primarily of interest as a depth profiling technique on samples with varying layers of both conducting and non-conducting materials, it is also capable of rapid bulk analysis of homogenous, solid samples. GD-OES combines the advantages of ICP-OES (wide detection range, speed, and lack of interferences) with the solid sampling of XRF techniques. This allows the analyst to not only quantify the elemental composition of a sample, but to evaluate it in terms of homogeneity with depth, a field in which auger electron spectroscopy (AES) and secondary ion mass spectrometry (SIMS) have traditionally been the primary techniques. Although GD-OES does not replace these useful techniques, it does offer various advantages over them, making it an excellent complementary analytical tool.In GD-OES analysis, a low-pressure glow discharge plasma is generated with the sample material acting as a cathode, accelerating the cations in the plasma towards the sample surface. This bombardment causes the sample material to ‘sputter’, essentially knocking free atoms or molecules of analyte material, which are then drawn into the plasma where they are excited. The light emitted by this excitation is then diffracted to separate the wavelengths emitted by the specific elements and detected by a spectrophotometer. The intensity of the signal is directly proportional to the quantity of analyte element present in the sample, allowing simple calibration and quantitative determination of the elements. Technological improvements made in the past twenty years or so have significantly increased the usefulness of GD-OES for surface analysis. Faster plasma stabilization and start-up allow for the quantification of surface layers as thin as 1 nm. Sputter rates have been accurately measured for many common materials, allowing them to be built into software libraries in the instrument’s control software. This dramatically expands the usefulness of this software and the ease of performing analyses.GD-OES analysis of nuclear materials allows for the rapid determination of the elemental composition without the requirement of initial dissolution. The thickness of any corrosion layers on nuclear materials can also be determined."

Jan 1, 2015

By Christopher Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940’s and 1950’s. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as “one of the great social advances of our time.” Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support’s strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, “roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization.” Yet by the end of the 1950’s, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives. The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

By Amanda Elioff

Success of the Gold Line Eastside Ex-tension rail tunnels in Los Angeles, CA has prompted the Los Angeles County Metropolitan Transportation Authority?s (Metro) planning new rail lines to include underground alternatives. The Westside Extension Transit Corridor alternatives include up to 27 km (17 miles) of subway to be constructed in soft ground. The routes will require construction in Los Angeles? ?potential methane zone,? which was not considered for subway construction until recently. Slurry face tunnel boring machines (TBM) will likely be specified.

Jan 1, 2009

By Tad S. Golosinski, R. Larry Grayson

Online education is not new. During the last decade, it has reached the stage where many universities offer a variety of courses, degrees and programs without any associated residency requirements. The most successful of the online universities, University of Phoenix, offers hundreds of accredited programs for close to 100,000 students throughout the world (www.phoenix.edu). Online education is considered to be a valid equivalent to traditional, classroom-based education. It is best suited to the needs of mature students with full-time jobs and a desire to deepen their knowledge. While most of the e-business has experienced severe setbacks during the last two years, e-education shows no signs of slowing down. On the contrary, the number of students and institutions offering online education keeps growing. The value of e-education associated expenditures was expected to reach $300 billion in 2001 (Sanoff,2001), making it a serious and mature industry.

Jan 1, 2002

By Peter Radziszewski

"Typical mining operating costs can be divided between extraction (30 % to 70 %), comminution (30 % to 50 %) and separation (5% to 20% ). Cornminition process costs, representing an important contribution to mining operating costs, can themselves be divided roughly between energy (50 %) and linerkharge wear (50 %). Developing the ability of predicting mill wear will allow a more accurate estimation of wear costs. However, total media wear in a given ball mill grinding process is a product of three recognized wear mechanisms those being abrasion, corrosion and impact. Further, the contribution to total media wear of each of these wear mechanisms has not been well established. In this paper, a overview of abrasive, corrosive and impact wear mechanisms is made from which an empirical wear prediction procedure is proposed. Further, future directions in wear prediction research is outlined. INTRODUCTIONTypical mining operating costs can be divided between extraction (30 % to 70 %), comminution (30 % to 50 %) and separation (5 % to 20 %). Comminition process costs, representing an important contribution to mining operating costs, can themselves be divided roughly between energy (50 %) and lined-charge wear (50 %). With respect to wear, world wide steel consumption as grinding media is estimated at over 600 000 tomes per annum (Malghan, 1982). As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs.Charge media wear prediction is actually estimated using the Bond abrasion test. From Bond abrasion index tests, it is possible to determine a wear rate using the following function:"

Jan 1, 2000

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By J. R. Thoenen

Up to 1914 almost all of the world's supply of potash came from Germany and Alsace. With the cessation of shipments from Germany during the World War the importance of a domestic suppler was evident. During the past 15 years the United States has been working toward the establishment of a domestic potash industry which would end foreign dominance in this commodity. The Federal government has taken an active part in this program. As its share in the work, the Bureau of Lines has ascertained the potash resources in certain district's through core drilling and has engaged in a comprehensive program of research on the extraction of potash from its various minerals. Until the passage of the Winter bill (H. R. 496) by Congress in 1928 the Bureau of Mines had not been able to give any consideration to the western ores, wyomingite (leucite) and alunite. With the massage of this bill, however, the ray was opened for the extension of the potash studies to cover these materials.

Jan 1, 1932

By J L. Mauk

The Sovereign, Jubilee, Scotia and Jasper Creek prospects occur in an area of ~3.0 km by 2.5 km (~7.5 km2) in the Hauraki goldfield. The prospects are hosted by andesitic to dacitic flows, autoclastic breccias and localised pyroclastic and air fall deposits. Jubilee and Sovereign prospects lie along the northern and southern parts of the Waitekauri Fault, respectively, whereas Scotia is located ~1 km to the E, and Jasper Creek a further ~1.2 km to the ENE. Wall rocks are typically intensely altered, although the degree of alteration becomes more variable east of Scotia and at Jasper Creek. Alteration minerals include quartz, adularia, albite, chlorite, pyrite, illite, interstratified illite-smectite, smectite and calcite. Several of these minerals have distributions that show distinct zonation with adularia most abundant at Sovereign and Jasper Creek, but restricted to shallow levels at Scotia. Illite occurs throughout Sovereign and Jubilee plus the western margin of Scotia where it grades into interstratified illite-smectite; smectite predominates at Jasper Creek. Veins are uncommon and typically narrow, but show distinct zonations. Quartz veins are more abundant at Sovereign and Jubilee, whereas calcite veins are more abundant at Scotia and Jasper Creek. Laumontite veins occur at Scotia, and rare clinoptilolite, mordenite and stilbite veinlets with calcite occur at Jasper Creek. Fluid inclusion in quartz and calcite homogenised between 141¦ to 272¦C and trapped a dilute solution with an apparent salinity of less than 2.6 weight percent NaCl equivalent. Homogenisation temperatures are hottest at Sovereign (average 241¦C) and Jubilee (average 239¦C), cooler at Scotia (average 204¦C) and coolest at Jasper Creek (average 162¦C). Calculated paleowater table elevations suggest the water table was 680 m to 750 m above sea level at Sovereign and Jubilee, 450 m at Scotia and 225 m at Jasper Creek. The current data suggest three scenarios that can explain why Sovereign and Jubilee are deep and hot, whereas Jasper Creek is cool, shallow and marginal; 1.   some or all of the prospects may represent separate overlapping hydrothermal system, 2.   a high-relief hydrothermal system on the side of volcano with an inclined water table and outflow towards Jasper Creek, and 3.   a low-relief hydrothermal system that has been either tilted or block faulted with greatest uplift and erosion to the west.

Jan 1, 2005

Despite the recovery of approximately six million ounces of alluvial gold from the West Coast of the South Island, New Zealand during the last 140 years, a great deal of this having been obtained via sluice boxes and riffle tables, there has been little advance in riffle table technology during this period. In this paper contemporary riffle table design and current operational practices are examined. Studies of gold loss to undersize tailings are described. In addition recommendations derived from recent research carried out in North America are contrasted with gold saving strategies adopted by West Coast miners.

Jan 1, 1992

By D M. Marques, J F. C L Costa

The estimation of process plant head grade is not trivial and is a source of constant dispute within the mining industry. Grade estimates informed by the short term mine planning are frequently not reproduced by sampling the continuous flow of ore at the plant. Head grades are normally obtained by periodically sampling the continuous flow during a day or shift, and taking the average of the multiple increments collected. The standard error of this mean grade depends on the ore variability and the frequency (number) of aliquots extracted. The more increments are taken the higher is the precision on the calculated mean. Variographic experiments are normally used to map grade variability along a certain period of time and the extension variance is derived from this variogram. This experiment is time consuming, expensive and cumbersome. Mining industry personnel rarely apply this approach. Additionally, a temporal variogram can vary from day to day as different ores are mined along the life of the mine. This paper investigates a novel approach based on simulating the grades feeding the processing plant. In situ 3D grade models are built using geostatistical simulations. Grade spatial continuity and variability are reproduced in models that mimic the real deposit. These models are used in mine planning and scheduling transforming a 3D block model into an one dimensional string of values feeding the plant (one dimension flow). These grades have the statistical characteristics of the unknown real grades and can be sampled to emulate a variographic experiment. The results showed consistency and adequacy to estimate the sampling error (Gy, 1998 p 31) for various sampling intervals using the simulated grades. Also the results show a variographic experiment can change significantly from time to time, as ore changes and a selected sampling protocol can become obsolete if not adjusted for ore variability.CITATION:Costa, J F C L and Marques, D M, 2012. Defining a sampling strategy for a continuous flow supported by geostatistical simulations, in Proceedings Sampling 2012 , pp 3-8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By D. S. F. Silva

A survey of 120 recent NI 43-101 technical reports was conducted to evaluate the current state of practice regarding resource classification techniques. The most common classification techniques are based on search neighbourhoods (50% of recent reports), drill-hole spacing (30% of recent reports), and/or kriging variance (6% of recent reports). Two new techniques are proposed. The first is based on kriging variance and involves removing one or more drill-holes with the highest weights while performing kriging and using the resultant kriging variance for classification. This technique has the advantages of variance-based techniques and reduces artifacts. The second technique is based on conditional simulation and uses a moving window approach for classification at the desired selective mining unit resolution based on larger production volume criteria. This technique has the advantage of accounting for heteroscedasticity, which is a common characteristic in mineral deposits, and also reduces artifacts since a production volume scale is considered for the actual classification. The drill-hole spacing, search neighborhood, kriging variance, and simulation-based techniques are described and compared for 2D and 3D examples with regular and irregular drilling patterns to highlight the advantages and disadvantages of each method.

Jan 1, 2014

The two candidates in the upcoming presidential election in the United States each say that they have their own solution to the nation?s energy problems - solutions that will increase the amount of energy available, lessen the nation?s dependence on foreign sources and reduce the amount of pollution released to the atmosphere. Democratic nominee Sen. Barack Obama and Republican candidate Sen. John McCain both advocate research funding for coal-to-liquids and clean coal technologies. McCain also supports increased oil and gas drilling offshore. And Obama has even made some noises in that direction, although his plan leans heavily on the increased use of renewable energy sources. The energy debate is not new to this election. Congress and whichever party is in the White House has for years been trying to craft a comprehensive energy policy. One difference in this latest debate is that the increased use of nuclear energy has gained more attention. Current President George W. Bush has said he favors the increased use of nuclear power as part of the nation?s energy package. And McCain said he supports the building of more nuclear power plants. Obama has not said much about that. The American public is also showing signs of changing its stance on nuclear energy. To be sure, images of Three Mile Island and Chernobyl are still alive in some minds. However, the American public has said it wants cheaper energy and they want it produced more cleanly. With nuclear, the nation can have both. In the United States, nuclear accounts for slightly less than 20 percent of the electrical power used (see interview with Gary Steele of Energy Fuels on page 27). Globally, that figure is about 15 percent. And there are several nations that derive better than half of their power from nuclear sources. Add to that the world?s increasing need for more energy and the future of nuclear is bright.

Jan 1, 2008

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objective and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the following material is presented: (i) review of related literature, (ii) mathematical models to perform quantitative analyses of accident/ injury experience data using the tools and techniques of risk analysis, time series analysis, and the Markov process, and (iii) descriptions of the HDBSEL and ACIM programs which are used to perform accident/injury experience analyses and cost analyses, respectively.

Jan 1, 1993

By M. Poirier, J. H. Mbouche

"The research question of the present work is the following: at which speed should a rotary sample divider operate in order to produce representative samples of iron ore concentrate? In order to solve this problem, the representativity of a rotary sample divider treating iron ore concentrate from Iron Ore Compagny (IOC) Carol Lake mine in Labrador City was studied in the laboratory of mineral processing of “CEGEP de Sept-Îles”. The rotary sample divider speeds tested are: 20, 40, 50, 60, 80 and 100%. The results show differences in both weight and particles sizes distributions with respect to the various rotation speed used. 20% has shown to be the speed that generates an almost normally distributed samples for both weight and particle size. As the speed of the rotary sample divider increases, the polygon of frequency for weight distribution progressively becomes a two modal distribution curve. 40, 50 and 100% speeds generate normal samples distribution curves with respect to particles size only. 60 and 80% are the speed to be avoided since they generate multiple modal distribution curves for both weight and particles size.IntroductionIn the mining industry, samples representativity is part of the key elements for management decisions. In fact, “Sampling provides vital information to plant operators, clients and geologists to profitably run and operate iron ore mines and plants” (Kevin Thorne et al. 2007). At the laboratory scale, several types of techniques’ are currently used to perform sampling. This include: grapping, alternate spading, quartering, riffles divider and rotating divider etc.. Among all these instruments, rotary divider is the most commonly used. Nevertheless, the usage of a rotary divider is not a guaranty for samples representativity since the results have shown to be related to running speed of this instrument. For the present research work, the idea is to use iron ore concentrate to quantify the representativity of a rotary sample divider. In other words, the research idea is to determine the speed at which a rotary sample divider produces representative samples while treating iron ore concentrate from Carol Lake mine. The present report will give an overview of the methodology used and the principal results obtained."

Jan 1, 2016

By A. G. Mayton

Vehicle vibration exposure has been linked to chronic back pain and low back symptoms among agricultural tractor drivers. The objectives of this study by the National Institute for Occupational Safety and Health (NIOSH) were to assess driver whole body vibration (WBV) exposures and recommend interventions to reduce the risk of back related injuries, particularly relative to vehicle jarring/jolting (the transient mechanical shock components of WBV). The methodology included collecting, from two independent samples, ?eld data and health and work history data of farm equipment operators. Data were collected during mowing, raking, baling, chiseling, tilling, and road travel for different model tractors. Spraying using a sprayer and shrub removal with a skid steer loader were also included. Based on ISO 2631 (1985), the American Conference of Governmental Industrial Hygienists, threshold limit values, presents 0.5 m/s2 as the action level recommended by the Commission of European Communities for overall weighted total RMS acceleration (vector sum for axes x, y, and z) [ACGIH, 2006. Threshold limit values and biological exposure indices. Cincinnati, OH]. WBV measured at the operator/seat interface exceeded this action level. The roughest rides and highest vector sum accelerations occurred with small utility tractor mowers (3.3 and 2.8 m/s2) and a skid steer loader (1.7 m/s2). Major ?ndings from health and work history data showed 96% of participants reported having to bend or twist their necks, although 24% reported neck symptoms. Sixty four percent of participating operators reported experiencing back symptoms (e.g., pain, aching, stiffness, etc.). Recommendations included: specifying a seat that ??better?? isolates operators from jars/jolts with new tractor purchases; maintaining the seat/seat suspension and replacing worn or damaged cushions with NIOSH tested viscoelastic foam padding; using larger diameter tires with radial ply instead of bias ply construction, particularly on small utility tractor mowers, to aid in attenuating ride ??roughness??; using a swivel seat to reduce the stress on the neck from bending or twisting; and improving efforts to educate owner/operators of the adverse effects of WBV exposures. Since the data presented in this paper were collected from two independent samples, the authors were unable to draw any correlations or etiological inferences from the study. However, results were compared and contrasted with other studies which included similar vibration measurements in agriculture.

Jan 1, 2008

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012