Search Documents

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis' in graphical form. In 1953 Fatt' also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie' equation, and the more general Winsauer equation', where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

Most mines in the Bundamba, North Ipswich, and Rosewood districts of the West Moreton coalfield of south eastern Queensland have installed washing plants during the last five years. Many problems were encountered in their installation, including the small size of washing plant required in many cases, the economical minimum ash content under present and future market requirements, production from a one-product washbox of large and small coal of quality to satisfy both markets, measures to avoid adding unnecessary moisture to the washed slack coals, and excessive middlings in some coals or soft clay in others.INTRODUCTIONIt was fortunate for Brisbane, which was to become the capital of a new State, Queensland, in 1859, and grow into a city of over half a million people by the time of its centenary, that coal was found in abundance almost on its doorstep near Ipswich, the first mine being opened at Redbank in 1843. This was followed by the opening of many more mines in that district and, some 40 years later, in the nearby Rosewood district where high-volatile gas coal was produced (Fig. 1). These discoveries ensured a supply of reasonably priced coal (currently about 85/- per ton delivered) in Brisbane, but the quality is inferior to that of other coals mined in Queensland beyond economic range of Brisbane.Various factors led to an increase in the average ash content of the West Moreton coals during and after the war. Between 1940 and 1952 the gasworks coals rose in average ash from 13 8 per cent to 23·9 per cent and the powerhouse coals from 17·1 per cent to 27·1 per cent. This drift was arrested by the installation of 28 screening and picking plants from 1952 onward, but it became obvious that mechanical cleaning of the coals was essential due to the competitive market for coal and the worsening quality of reserves.

Jan 1, 1963

By I. V. Baklashov

Geomechanical conditions of mining operation are determined by varying in time and space mechanical properties and initial state of the rock mass, by geological and technological factors. We define adaptive mining technology as a technology capable of adjusting to changing geomechanical conditions of mining operation. The ongoing research at Moscow State Mining University consisting of laboratory, theoretical, and field investigations aims at the development of theoretical basis and methodology of the system of geomechanical support of adaptive mining technology for the bedded salt deposit in the Urals, mined by room-and-pillar method. This system of geomechanical support is capable of - dynamically assessing mechanical properties and state of the rock mass varying within the panel; - mapping mechanical properties of the rock mass within the panel; - assessing and predicting mechanical condition of load-bearing elements of the rock mass and its changes due to the adjustment of the parameters of mining operation considering the in-situ geomechanical conditions.

Jan 1, 1996

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

Improved Process & Practices Result In: ? Reduction of undesirable downtime, & expensive secondary damage ? Improved equipment performance & health ? Extension of equipment life, & reduction of operating costs ? Safety and environmental performance improvement Equipment knowledge capture and consistently applied

May 1, 2010

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By P. D?Elia

Following a study by NIOSH on the availability of teams in the U.S. as well as existing training sites and their capabilities, the Penn State University, leaders of the Pittsburgh Section of SME, providers of mine rescue equipment, and industry sponsors united to establish and make fully functional a student mine rescue team at Penn State University. With the growth of MERD and mine rescue competitive events at Missouri S&T, the Mine Training and Technology Center in PA, and at Colorado School of Mines Edgar Mine, a critical mass of effective training venues were made available to help student teams progress and develop mine rescue skills. The challenges to be met in creating and developing a student mine rescue team will be discussed. The rewards from this type of effort will be the quick capability of graduates from mining engineering programs to be involved in not only mining operations, but industry mine rescue teams and other leadership roles as well.

Jan 1, 2012

By A. Asadi

Subsidence phenomenon as an unwanted consequence of underground mining can cause problems for environment and surface structures in mine area. Surface subsidence prediction for inclined and steep seams has been given less attention than horizontal seams due to the difficulties involved in the extraction of such coal-seams. This paper introduces a new profile function method for prediction of surface subsidence due to inclined coal-seam mining. The results of calculation with the new function indicate that the predicted value has good agreement with the measured data. Keywords: subsidence; coalmining; caving mining methods; longwall mining; profile function.

Jan 1, 2005

Australia is not capitalizing on the raw gems and precious minerals that it produces in abundance. In particular, there is an unrealised value for diamonds due to lack of processing after mining. Australia could enhance the value of its raw jewellery products by developing and integrated jewellery industry. For instance, initiation of a diamond industry would require training programmes to educate people in the requisite skills, such as diamond sorting, cleaving, sawing, bruting and polishing. Equally important would be the training of people in design jewellery, manufacturing, and appropriate diamond grading and sales techniques. Future technological advances in diamond processing will decide where the major diamond processing centres of the world will be. Australia, for a relatively small investment, could develop a highly productive diamond processing capacity using the new technology available. Australia's geographical position, and advanced banking and communication facilities provide the potential for this country to become a major trading centre for diamonds. KEYWORDS: Argyle Diamond Mine, Diamonds, Diamond Production, Diamond Sorting, Jewellery Industry

Jan 1, 1989

IN 1906, soon after his arrival in New Zealand, a brief article was prepared by the writer on "The Salient Features of the Economic Geology of New Zealand," for the Journal of Economic Geology. In November, 1907, a somewhat similar paper, entitled "The Mineral Wealth of New Zealand," was read at the Royal Colonial Institute in London. The present contribution to the Transactions...

Jan 1, 1909

By C Spandler, S W. Richards G Rosenbaum, R J. Holm

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The recent and active magmatic arcs of eastern Papua New Guinea (PNG) and the Solomon Islands are well endowed with sulfide mineralisation and include deposits such as Ladolam, Panguna and Solwara 1. The majority of the mineral systems in this belt are younger than four million years old, with some deposits remaining active to the present day as exemplified by active hydrothermal systems on the island of Lihir. The geodynamic setting that led to the formation of these deposits is still unresolved, with, for example, both the Pacific and Solomon Sea plates considered responsible for the formation of the Ladolam deposit on the island of Lihir under different models. In order to understand and characterise the formation of south-west Pacific mineral deposits, we must first reconstruct the complex geodynamic evolution of the region. New kinematic reconstructions show that while mineral systems in eastern PNG and the Solomon Islands are hosted within a single arc related to subduction at the New Britain and San Cristobal trenches, variable and discrete geodynamic settings exist within both the upper and lower plates throughout this region, which give rise to distinct mineralised corridors. Most notably, this region is host to: the Solwara 1 deposit, which occurs within a major transtensional corridor in the eastern Bismarck Sea the Ladolam deposit (Lihir), which is interpreted to have formed above but in relation to tearing of the subducting slab the Panguna deposit, which is related to structure in the subducting slab marginal to the actively spreading Woodlark Basin.An evaluation of the nature and variability of these diverse geodynamic settings through time can provide us with a better understanding of the relationship between the active south-west Pacific magmatic arcs and mineral deposit formation. It may also provide insights into the diverse array of deposit settings at ancient convergent margins, with applications in mineral prospectivity studies.CITATION:Holm, R J, Richards, S W, Rosenbaum, G and Spandler, C, 2015. Disparate tectonic settings for mineralisation in an active arc, eastern Papua New Guinea and the Solomon Islands, in Proceedings PACRIM 2015 Congress, pp 165–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By A-A Latscha, C Boyle

Geological modelling has historically been done using sectional interpretation of paper sections or on a computer screen. Boundaries of geological units or grade shells are interpreted by a geologist section by section and the shapes are drawn onto paper to be digitised later or they are directly digitised into a computer. This approach is referred to as explicit modelling. Such methods are time consuming if there are many section lines or boundaries to be interpreted. The number of metres drilled and resource models made is increasing each year and it will be difficult to keep up using explicit modelling methods. Alternatively, it is possible to use information carried in the drill holes, known geological relationships and point estimation methods in two or three dimensions, to create similar geology boundaries, while eliminating or at least greatly reducing the need to manually interpret and digitise detailed sectional interpretations. Such methods are referred to as implicit modelling and are available in a number of software packages. Implicit modelling approaches have been used in iron ore and found to significantly reduce the time needed for modelling while producing results that are comparable or better than standard explicit modelling approaches. A number of case studies have been undertaken of implicit modelling in iron ore deposits. Stratigraphic surfaces of bedded, folded and faulted iron ore deposits have been modelled in various deposits by Leapfrog Geo, GOCAD (with SKUA) and Vulcan Integrated Stratigraphic Modelling. Leapfrog Mining was used to model iron grade shells at particular cut-off grades. The modelled surfaces are of a high standard equivalent to those that could be produced by traditional explicit modelling but the time required by the implicit methods is far less. Implicit geological modelling is an active area of software development and improvements in software are likely.CITATION:Boyle, C and Latscha, A-A, 2013. Implicit geological modelling of iron ore deposits, in Proceedings Iron Ore 2013 , pp 57-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Allen D. Look, Alan A. Sharp

"INTRODUCTION The bottoming of the United Verde sulfide pipe has shortened the expected life of the United Verde mine to a matter of a few years. First located in 1876, this Arizona mine has had a long period of activity, having reached a peak production in 1929 of over 71,000 trans of copper. Through these many years of successful operation, a safety program has evolved in keeping with the proficiency developed in mining the ore body. It is the purpose of this paper to record the safety practices in effect at this mine so that others may have the benefit of lessons ,learned through experience 'and years of work toward an improved accident record.ACKNOWLEDGEMENTSAcknowledgment 'is 'made to ,the Phelps Dodge Corp. for its cooperation in making available data contained in this paper, and to C. E. Mills, general superintendent; W. W. Little, mine superintendent; John Riordan, employment agent; and G. S. Leisk, safety engineer, for their helpful suggestions and information furnished.GENERAL INFORMATIONThe United Verde copper mine is situated just west of Jerome, Ariz., at an altitude of approximately 5,500 feet. Purchased by the Phelps Dodge Corp. in 1935, the mine employs approximately 500 men - 385 underground and 115 on the surface."

May 1, 1949

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

By Johnson N. W

After an unsuccessful transfer from the laboratory to the pilot plant of galena flotation technology which used sodium metabisulphite and ethyl xanthate, laboratory flotation tests were conducted to identify any unusual variables which had a deleterious effect on the position of the lead rougher grade recovery curve for Hilton and Mount Isa silver-lead-zinc ores. Two variables (pulp temperature and contact time for ethyl xanthate and sodium metabisulphite) had important deleterious effects.The findings allowed a successful transfer of the laboratory process to a pilot plant scale process. The effect of temperature was important because the higher temperature (40°C) in the pilot plant pulp increased significantly the rate of reaction between ethyl xanthate and sodium metabisulphite. In the laboratory process at 20 to 25°C, the reaction rate was lower and did not interfere significantly with the process. The contact time for the two reagents was also important in the pilot plant scale process because of the higher reaction rate at 40°C.To employ ethyl xanthate in the pilot plant process, special precautions were required. Further, a collector (Aerofloat 241) from the dithiophosphate family was used successfully in the pilot plant process.

Jan 1, 1988

By J. Asfahani

"The Schlumberger configuration used in geoelectrical sounding is slightly adapted here to obtain reliable data for both shallow and deep penetration depths from the same survey. In this configuration, two kinds of current electrode half-spacings are used: the first enables construction of vertical electrical resistivity sounding (VES) curves for shallow depths (<50 m), and the second for depths =250 m. For a given VES location, two field curves are measured and interpreted using two standard approaches. Practical characteristics of such a modified configuration are illustrated with two field applications in Syria. The first aims to characterize the structure of Quaternary and recent deposits in the Al-Ghab depression region, and the second deals with exploration for phosphatic sedimentary units in the Al-Sharquieh mine. La configuration de Schlumberger normalement employée dans les levés géoélectriques a été légèrement modifiée afin d’obtenir des données fiables à faible et forte profondeur durant le même levé. Dans cette nouvelle configuration, deux types de demi-espacements des électrodes sont utilisés : le premier permet le développement de courbes de sondage de résistivité électrique verticales (REV) pour les faibles profondeurs (<50 m), et le second atteint des profondeurs =250 m. Pour une localité REV donnée, deux courbes de champs sont donc mesurées et interprétées grâce à deux approches standardisées. Les caractéristiques pratiques de cette configuration modifiée sont illustrées par deus exemples d’application en Syrie. Le premier vise la caractérisation de la structure des dépôts Quaternaires et récents de la région de la dépression d’Al-Ghab, et le second traite de l’exploration pour des unités phosphatiques sédimentaires à la mine Al-Sharquieh."

Jan 1, 2009

By Wilson D, Kirkland J

Compressed air energy storage (CAES) uses low cost off-peak energy to compress air and pump it into pressurised underground storage. Expanding the air through a modified form of gas turbine generates electrical energy when required. While generating power, a CAES station consumes approximately one-third of the gas required for the equivalent installed capacity of a conventional gas turbine. Air can be stored in underground rock caverns, caverns in salt domes, or in aquifers. Existing CAES power stations use caverns mined out of salt domes. Aquifer storage for CAES has been proposed, but not yet implemented. The groundwater in the aquifer would be displaced during air injection and when required the air would be extracted using the natural hydro-static pressure. Victoria has no salt domes, but has aquifers onshore in the Gippsland Basin with geological dome structures of suitable depth, discovery pressure, porosity, permeability and caprock for CAES development. Field tests costing several million dollars would be required to prove the suitability. The most suitable aquifer is near Seaspray, where several dome structures exist. The aquifer, comprising of coarse sands capped by coal and mudstone, is some 600 metres deep with a hydrostatic pressure of 6.3 MPa. Computer simulation of injection and extraction of air from the aquifer under various combinations of horizontal and vertical wells, permeability and tubing head pressures indicated the largest aquifer structure had the capacity to sustain a 300 MW station. A well field comprising of 24 directionally driven wells with a horizontal exposure to the aquifer would achieve the air flow rates required. Using plant similar to that recently installed at McIntosh Alabama USA, would mean high capital costs compared to standard gas turbine plant. However, a review of modem gas turbines indicated that they could be easily and economically adaptated to CAES duty. Adapting a 120 MW gas turbine would give 344 MW output. A separate air compression plant would be used. Economic evaluations indicate that, for gas prices above $1.95 per GJ, a 344 MW CAES plant is more economic for intermediate/reserve load duty than simple cycle gas turbines.

Jan 1, 1992