Search Documents

By Esher Hsu

Keywords: Recycling, Consumer Battery, Fee rates On November 11, 1999, all types of spent consumer batteries are proclaimed to be collected in Taiwan. Under current recycling system, all producers and importers of consumer batteries have to pay a collection/recycling fee to the Recycling Management Fund (RMF) of EPA based upon the rate approved by EPA. Collectors and recycling plants receive subsidies from RMF according to the collected and treated amounts audited by an independent auditing organization. Collected spent consumer batteries only reached 923 tons in 2002 equivalent to 10% of the total quantity sold at the same year. How to increase the collection efficiency of used batteries becomes an important issue for EPA in Taiwan. The objective of this study is to explore current recycling system of spent consumer battery in increasing collection efficiency. Results provide some suggestions to Taiwan EPA regarding recycling route, recycling system, recycling rates, and recycling subsidies.

Jan 1, 2005

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010

By Larry M. Southwick, Phillip J. Mackey, A. E. (Bert) Wraith, Albert Pelletier

In 1881, the first commercial pneumatic Bessemer-type converter treating copper matte was successfully introduced by Pierre Manhes at the Eguilles copper plant near Vedène in France. This development followed over a year of testing on a smaller scale at a foundry in Vedène, during which the vertical tuyeres of the conventional Bessemer converter had been successfully replaced by horizontal tuyeres in an effort to avoid the freezing of copper which had occurred in the bottom of the vessel having vertical tuyeres. The Manhes Converter, as it became known, was the first successful large-scale adaptation of the Bessemer concept of using compressed air blown into a melt for metal refining and treatment. Within a few years, Manhes Converters utilizing horizontal tuyeres in either the original type of vertical converter, or a later and more enduring horizontal barrel converter, were in operation at over a dozen copper smelters around the world. It was this process that Messrs Peirce and Smith essentially improved with the introduction of the larger converter which bears their name and the development celebrated at this Symposium. The present paper briefly traces the original development by Pierre Manhes in the early 1880s and which set the stage for the later Peirce-Smith adaptation. The paper observes that the original development by Manhes was in part driven by the need to reduce coal (energy) consumption and hence the production cost in order for Eguilles to remain competitive with the larger plants in Swansea, Wales, where a ready supply of cheap coal helped keep smelter treatment terms of the day low. These themes are eerily resonant of today where booming copper production in China has impacted the industry, and also where energy consumption, closely linked to today’s more familiar theme of ‘climate change’ remains an important challenge currently confronting the entire industry. The paper concludes with comments on these seemingly parallel situations today and offers some thoughts for the future.

Jan 1, 2009

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By G. N. Shannon

Keywords: inclusions, slag, modeling, interfacial energy, capillary force, particle flotation, particle separation A previously introduced model of inclusions separating across a steel-slag interface, developed by Nakajima/Okamura and Bouris/Bergeles, is expanded to include different inclusions shapes (octahedral and plate-like, besides spherical) as well as comparison between model ladle-, tundish-, and mold-slags. Investigation of the relation of these shapes with the interfacial capillary force ? which arises due to the dynamic interfacial energy during separation ? has shown that the force has a significant effect on whether the inclusion separates rapidly or settles at the interface. For the slags considered, the most significant physical property is found to be viscosity, which resulted in fast separation times for inclusions in the mold and ladle slags, relative to the more viscous tundish slag. Particle dissolution (using experimental data) is included in separation modeling.

Jan 1, 2005

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

By Zhan Jing

Keywords: thermodynamic, Ni-Co alloy powders, composition, fibrous The mathematics model of Ni(II)-Co(II)-C2O42?-NH3?H2O-H2O of thermodynamic equilibrium system has been developed theoretically according to the law of conservation of mass and the law of simultaneous equilibrium, and the logarithm concentration-pH (log[Me2+]T-pH) diagrams of this system have been made. The effect of ligand and pH value was studied. Two issues in coprecipitation route to synthesize fibrous nickel-cobalt alloy precursor powder, com-position and morphology which are a first priority, are addressed based on thermodynamic analysis and experiments. The results show that suitable pH value range of coprecipitation of nickel ions and cobalt ions in theory can be obtained to maintain fibrous, excellent compositonal homogeneity and stoichiometry in coprecipitation products. Experimental demonstration is also carried out.

Jan 1, 2005

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By D. H. Magoon

The zinc smelter of Cominco Ltd. at Trail, B.C. Is the largest In the western world. A total of 550.000 tonnes of concentrate are proceed at the smelter annually. Approximately 80% of the zinc concentrate is roasted and the remainder Is treated by aqueous oxidation preaaure leaching. The zinc concentrate roasting and sulphur dioxide gas processing plants have undergone many changes over the years. This paper describes the processes and equipment currently used for concentrate roasting, S02 gas cooling and cleaning, mercury removal, sulphuric acid production liquid S02 production, and tall gas S02 scrubbing. The recent Installation of an advanced process control system for the operation of these Integrated processes Is also described.

Jan 1, 1990

By Hector Carreon

Due to elevated temperatures, excessive stresses and severed corrosion conditions, turbine engine components are subject to creep processes that limit the components life such as a turbine bucket. The failure mechanism of a turbine bucket is related primarily to creep and corrosion and secondarily to thermal fatigue. As a result, it is desirable to assess the current condition of such turbine component. By using eddy current images, it was shown that the eddy current technique could be used to monitor creep damage in a nickel base super-alloy. The eddy current results also show a significative variation in the electrical conductivity on the creep damage zone with respect to the background zone in nickel-base super-alloy samples. In addition, the absolute thermoelectric power coefficient show also a strong dependence associated with creep damage in nickel base super-alloy samples using a copper hot tip reference. The eddy current and thermoelectric power techniques seems to show promise as nondestructive evaluation tools for monitoring the level of creep damage in metallic alloys.

Jan 1, 2010

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By Varadajan Seshadri

Keywords: torpedo car, kinetics, physical modeling A 1:6 torpedo car physical model was built to assess the optimum refining conditions for pig iron desulfurization in the torpedo car considering the industrial parameters used in the steel plant CSBM (Companhia Siderurgica Belgo-Mineira, João Monlevade, MG, Brazil). The refining practice in this plant is through injection of a CaO-CaF2-Mg powder in the pig iron melt. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation were also evaluated.

Jan 1, 2005

By Heikki Jalkanen

The mineralogical composition and morphology of solidified copper smelting and converting slags are of some interest from slag cleaning (by froth flotation), impurity elimination, and environmental points of view. Properties result from both the state of molten slag before solidification and processes taking place during solidification and cooling. In solidification and cooling, copper and sulfur dissolved in molten slag are .precipitating substantially from the silicate phase. Even in water quenching of slag, dissolved copper is pushed out of the solution in the form of finely divided precipitate. Elements present in the raw materials are distributed in a distinct manner between the solidified slag and non-silicate solidification products. Arsenic, antimony, and tin are strongly accumulated in copper precipitate, but not the other metallic constituents common in copper concentrates. Smelting and converting slags differ remarkably on their mineralogical composition and morphology although resulting principally of same chemical processes. Converter slags are more inhomogenous; they often contain solid particles and copper content is .as a rule higher than in matte smelting slags. The final copper content of converter slags was observed to be in a distinct manner dependent on iron oxide - silica ratio. Slag forming, solidification, and precipitation phenomena are discussed on the basis of mineralogical and morphology analysis of smelter slags and laboratory scale experiments.

Jan 1, 2002

By M. D. Strachan

Technical & Procurement Services Limited (TECHPRO) in Ashford, Kent, UK, have been appointed as Project Managers for the major rehabilitation of the Copper Smelting complex of Nkana Division, Zambia Consolidated Copper Mines Limited, (ZCCM) Zambia. In outline, the overall scope covers three main areas: a) Transfer and implementation of new technology into Zambia for the production of primary copper. b) Replacement of gas collection and gas treatment circuits to guarantee high quality feed to the acid plants. c) Completion of a number of minor projects in the copper smelter and associated utility plants to complement changes in the primary smelting technique. This paper describes the Project Management methodology and style used by TECHPRO to tackle typical problems that arise in retrofit projects of this type. Reference is made specific aspects of the smelter projects to illustrate solutions to the problems. The subjects. addressed highlight the complexities not only of having a -Client 5,000 miles from the Project Office, but also the difficulty of co-ordinating and controlling the performance of min sub-contractors who are also geographically distant.

Jan 1, 1991

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By Torben Edens

Norddeutsche Affinerie?s (NA?s) primary smelter continually increased production in the past decade. The smelter?s concentrate capacity was expanded from 500,000 in 1993 to 1,000,000 t/a dry concentrate in 2000 and the goal of the present upgrade is 1,150,000 t/a. These goals were reached without erecting new equipment in the anode area, but instead by refitting the existing plant. The life-span extension of the casting moulds was absolutely necessary to increase the casting performance from 260,000 to 450,000 t anodes per year on a single casting wheel. Different mould manufacturing processes and alloys were tested in order to find the optimal mould. In the past the moulds were cast directly, now the anode mould is milled into NA copper cakes. Accompanying measures taken were the shortening of maintenance and repair times as well as improvements in the refining furnace equipment.

Jan 1, 2005

By Bowen Li

Silicon Carbide is an excellent refractory material. Its physical properties make it extremely useful, particularly in applications where corrosion resistance and wear are important considerations. Commercial silicon carbide refractory is frequently manufactured by bonding silicon carbide particles with clay; however, clay may cause problems in the sintered products. This study investigates the potential of replacing a portion of the clay with andalusite powder. The results show that micron size andalusite powder can improve not only the strength of the refractory but also the sinterability. The mechanisms for these improvements are discussed.

Jan 1, 2006

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010