Search Documents

By Alireza Zakeri

To evaluate the behavior of minor elements in the copper smelting process, activities of silver, selenium and tellurium at minor concentration were determined at 1473 K within the miscibility gap of the Cu-S-Me (Me = Ag, Se, Te) and Cu-Fe-S-Me systems varied in Fe/Cu ratio. Phase relations between the immiscible metal and matte phases in the foregoing systems were first established by a quenching technique at 1473 K to supplement the activity measurement data. A Knudsen-effusion mass spectrometer, capable of handling complex gaseous systems and relatively small vapor pressures, was adopted for activity determination. Using a multiple Knudsen-cell, the ion intensity of minor element in the sample under study was measured simultaneously with that in a reference sample. Activity was obtained from the ratio between the measured ion intensities as well as the known activity value of the minor element in the reference sample. Limiting activity coefficients of the minor elements were correlated with composition of the matte. Based on the experimental results, the vaporization behavior of the minor elements has been discussed.

Jan 1, 1999

By F. Guevara

The paper presents results of physical and turbulent three-dimensional numerical simulation of the gas flow in the wind box and reaction shaft of the concentrate burner of a flash furnace. Physical simulation work was carried out in a 1:5 linear scale model, where the velocity field was measured using a Pitot tube. The mathematical model consists of the three-dimensional averaged Navier-Stokes equations, turbulent kinetic energy and dissipation of turbulent kinetic energy using the Renormalization Group (RNG) theory for the k-e turbulence model. Computations were performed using FLUENT, based in a finite- volume code. The geometry of the concentrate burner was separated in two sections: wind box and reaction tower. Results obtained at the exit of the wind box were used as boundary conditions for the reaction shaft. The effect of boundary conditions on the numerical results was also studied. Results of physical and numerical simulations show an asymmetry of the velocity field at the exit of wind box. This asymmetry is possibly due to existence of a separated flow in the back of the exit ring. The agreement of physical and numerical results assess the capacity of the turbulence RNG k-e model to reproduce correctly the behaviour of the velocity field at the exit of the concentrate burner.

Jan 1, 1999

By Bruce Cavender

Managers are frequently faced with the decision to perform a task or manufacture an object in-house or to hire an outside vendor to perform the function. Outsourcing decisions are usually driven by economics: work is outsourced if it can be completed at a lower cost or in a shorter time than it can in-house. A technique termed incremental analysis can be used to make this decision. Incremental analysis examines the financial impact of outsourcing decisions as a function of the firm's fixed and variable operating costs. To use this tool, individual components of production cost are identified as being either constant or varying with levels of production activity. The assignment of cost type can be made in several ways: though analysis of historical operating data, understanding of individual expense types, and so forth. Changes in fixed and variable costs resulting from each potential course of action are explicitly identified to project the financial outcome of each alternative. The alternative having the greatest positive impact on profit is selected for implementation. By using the fixed- and variable-cost framework, the analysis is conceptually straightforward and substantially simplified. Production managers can therefore use incremental analysis as a tool for fast economically beneficial decisions on a real-time basis.

Jan 1, 1999

By Shaolong Chen

Feeding dry sulfide concentrate into smelting furnaces enhances process performance and reduces the energy consumption and exhaust gas flow. Direct heated rotary dryers and flash dryers have being replaced by rotary steam dryers featured by very low wear rate of the pipe heating elements and long maintenance interval. Impact of the drying processes on the environment receives more and more attention as the emission legislation tightens. In this regard, environmental factors such as SO2, CO2, dust and gas flow among rotary dryers, flash dryers and steam dryers were compared. Selection of a rotary steam dryer for copper and nickel concentrate drying would be an ideal solution to reduce the pollution of exhaust gas, as drying is achieved by indirect contact to the steam at relatively low drying temperature and as the off-gas contains almost only water vapor and air. The emissions can be significantly reduced and only small and simple off-gas handling units are needed.

Jan 1, 2006

By Manolete Mena

WC-Co nanocomposite powder is among the first group of materials with a promising potential for nanocrystalline-materials application. A chemical vapor synthesis (CVS) process that has previously been used for preparing the aluminides of titanium and nickel, and other metallic and intermetallic powders has been applied to the preparation of WC-Co nanocomposite powder. This CVS system was designed so that a tungsten precursor (WCl6 powder) and a cobalt precursor (CoCl2 powder) were separately fed into each evaporator in a reactor by means of specially designed powder feeders. The reduction and carburization of the vaporized chlorides by methane-hydrogen mixtures produced nanosized WC and Co composite powder. The product is a very uniform mixture of the constituent powders, which is important to ensure a high quality of the bulk cemented tungsten carbide product after consolidation. In the present work, the effects of reaction temperature, CH4 to WCl6 ratio, CH4 to H2 ratio, residence time, and Co content on the powder composition and particle size were determined. The products were characterized using XRD, carbon analyzer, and TEM.

Jan 1, 2006

By Frank R. A. Jorgensen

Flash smelting is used to smelt a large proportion of the world's copper and nickel and some lead/zinc concentrates. Understanding the factors controlling the ignition of these concentrates is an important consideration in designing burners and maximising the throughput of the flash smelting process. The literature on the subject is briefly reviewed and techniques for the measurement of ignition temperature discussed. The mineralogy of the concentrates and the role of thermodynamics and phase diagrams in interpreting and predicting ignition behaviour are emphasised and applied to interpreting results obtained on a nickel concentrate.

Jan 1, 2002

By Kazuyoshi Sato, Keizo Uematsu, Nozomu Uchida

"Confocal fluorescence scanning laser microscope was applied to characterize the surface flaw of ceramics in great detail. A high potential -of the characterization technique is presented first. Then the technique was applied to clarify the relationship between the flexural strength of ceramics and the surface flaw. This kind of direct information of surface flaw should be essential for the fundamental study in this area, but has been lacking. The examination revealed that large defects are present on the machined surface of ceramics. Their size is consistent to the flexural strength measured on the material. The characterization tool was also applied to examine the formation of surface flaw in machining of ceramics.IntroductionClarification of fracture origin should be the starting point in the study on strength in ceramics. However, this task has been extremely difficult in some ceramics, such as an alumina ceramics. It may break from both internal and surface flaws. The former should reflect the quality of production process and the latter the machining. Examination of surface flaws should be very important for developing a better machining method for ceramics. The knowledge may valuable for establishing a better production process also.ExperimentAlumina Referceram (JFCC) was used as samples. They are cut to size of 3x4x40mm, and the surfaces were ground to meet the requirements of testing method for flexural strength of fine ceramics, JIS R 1601. They were soaked in an aqueous solution of fluorescence dye and evacuated with an aspirator for an hour to allow the solution penetrate into surface flaws. After excessive solution remained on the surface was removed by gentle washing, the specimens were dried at 120°C for 48 hours. The 4 point bending mode was applied to measure the fracture strength."

Jan 1, 2000

By J. G. Peacey, P. Hancock, R. -Q. Li

A pyrometallurgical process for the direct recovery of zinc from zinc concentrates and zinc/iron residues has been proposed and tested extensively by Noranda. The process consists of smelting bone-dry zinc containing materials (sulfide concentrates and secondary zinc/iron materials) in a molten iron oxysulfide bath to volatilize metallic zinc into a SC^-free offgas. Sulfur contained in the feed materials is fixed as an iron oxysulfide matte for disposal. Thus, this process not only is capable of treating zinc sulfide concentrates and secondary zinc materials simultaneously, but also eliminates the need of sulfuric acid production. Detailed thermodynamic analysis and experimental test work are described in this paper.

Jan 1, 2000

By Ximena Massone

Chile is the most important copper producer in the world and the mining sector plays a key value in its economy. However, at present the country does not have a satisfactory set of regulations about closure and restoration of mining operations. In our country many mining operations will, in the near future, shut down their activities, therefore, it is of utmost importance to elaborate and enforce a set of regulations to prevent risks and to protect the environment. The present study is focused on reviewing and analyzing the existing national regulations about the closure of mining operations and preparing a comparative analysis with other international regulations of countries with mining experience. The final results of the study will be a legal proposal to regulate the closure of mining operations in Chile, aiming at minimizing the potential environmental adverse impact, internalizing the social costs by the relevant operators and defining all aspects of liability for the environmental damage.

Jan 1, 1999

By Claire A. Chanenchuk

Catalytic Extraction Processing (CEP), a technology commercialized by Molten Metal Technology, Inc., a US.-based company, can convert industrial, household, and government wastes into commercial resources. CEP is an innovative elemental recycling technology that uses a molten metal bath to completely dissociate hazardous or toxic components of a feed and convert them to valuable products. The catalytic action of the molten metal bath converts the feed to its elemental constituents and the reducing atmosphere prevents the formation of any dangerous byproducts (NOx, SOx, dioxins, furans, etc.). Selective reactant addition allows engineering of valuable products from otherwise unexploited resources. Synthesis gas is generated from hydrocarbon feeds, ferro-alloys from metallic wastes, and ceramics from select inorganic species. Commercial-scale processing of multiple wastes and waste surrogates has been carried out at a destruction and removal efficiency exceeding 99.9999 wt.%, validating theoretical predictions. Unlike conventional hazardous waste treatment technologies, CEP offers resource recovery, minimal byproduct generation, and the potential for closed-loop recycling.

Jan 1, 1994

By L. B. Tsymbulov

At present data on thermodynamic properties of metallic melts, containing copper and ?iron family? metals, is rather limited. Determination of the activity of metallic melts components under high temperature by experimental methods requires high level of labour inputs. With this it is not always possible to obtain the results with high level of accuracy. Due to that in a number of cases it is more appropriate to apply different methods of analysis, with the help of which there can be calculated thermodynamic properties of ternary and even more complicated systems, prominent thermodynamic properties of binary systems being used as a basis for these calculations. This work presents the results of calculations of different components activity and activity ratio in such ternary system melts as Ni-Cu-Fe, Ni-Cu-Co, Fe-Cu-Co and Fe-Co-Ni. Good compliance of calculations results with those obtained in the course of reliable experimental investigations fulfilment is demonstrated. There are presented the results of activity and activity ration analysis for some compositions of Cu-Ni-Co-Fe system.

Jan 1, 2006

By Toshihide Takenaka

Improvement of corrosion resistance of Mg metal by addition of rare earth metal (RE) was studied, and the effect of surface oxide layer with RE was investigated. The corrosion resistance of Mg was remarkably improved by adding a small amount of RE, and the suitable RE content was clarified. The corrosion resistance of Mg was particularly bettered by conversion coating using a solution including both RE(NO3)3 and Mg(NO3)2. This result indicates that the surface oxide layer consisting of both Mg and RE gives good corrosion resistance to Mg metal. In this study, direct electrodeposition of Mg metal containing RE was also tried in molten chloride with RE chloride, and it was shown that electrolysis could be performed stably. The RE content in the deposited Mg metal was depended on the concentration of RE chloride in the bath and the cathode potential, and Mg metal containing the suitable RE content for its corrosion protection was obtained easily by direct electrolysis.

Jan 1, 2006

By Rudolf Keller

In the electrolysis of neodymium oxide from a molten fluoride electrolyte, anode effects may occur at the carbon anodes, interfering with smooth cell operation. In laboratory experiments, we attempted to circumvent this problem by selecting electrolytes with a high oxide concentration, possibly at relatively low rare earth content, but cathodic deposition was not satisfactory. A regime at higher cell voltage was discovered to yield good cell performance, but evolution of considerable amounts of fluorocarbon compounds suggested that a reactive treatment of the off-gases would be necessary for environmental acceptability. Subsequent experimentation at low cell voltage revealed conditions for satisfactory operation without occurrence of anode effects and without formation of any CF4 or C2F8.

Jan 1, 1997

By Gjergj Dodbiba, Toyohisa Fujita, Takahiro Kikuchi, I-Chen Wu

"In order to separate molybdenum (Mo) from the high-level radioactive liquid waste (HLLW), Pb-Fe based adsorbents were synthesized. The adsorbents were precipitated by adding sodium hydroxide in mixture of 1 mol/L lead nitrate and 1 mol/L ferric nitrate aqueous solutions. Each precipitate was then filtered, dried and ground to obtain a fine powder, which has been used as an adsorbent. Two main parameters were considered when synthesizing the adsorbents, i.e. the pH value at precipitation of adsorbent precursor and the calcination temperature of Pb-Fe based adsorbent. Moreover, the structures of the synthesized adsorbents were investigated by means of an X-ray diffractometer.The experimental results indicated that the calcination temperature of the Pb-Fe based adsorbent has a great influence on adsorption capacity of the adsorbent for Mo. It was found that when the Pb-Fe based adsorbent was calcinated at 500 oC, the sorbed concentration of Mo was the highest.1. IntroductionThe high-level radioactive liquid waste (HLLW), arising from the reprocessing of nuclear fuel are generally immobilized in an alkali borosilicate glass matrix. Broadly speaking, alkali borosilicate glasses are the matrix of choice for the immobilization of the HLLW, since they permit vitrification of waste stream of variable composition, [1]. Within this frame, the incorporation of molybdenum (Mo) is of particular interest in the vitrification of HLLW. Molybdenum is know to have a low solubility in borosilicate glass compositions and its presence in excess results in the phase separation of a complex yellow molten salt during vitrification, [1]. The formation of so-called “yellow phase” material during the vitrification process is undesirable since it leads to the accelerated corrosion of the inconel crucible liners. Furthermore, the “yellow phase”, which is reported to contain also other fission products, is soluble in aqueous solution providing a potential route for the leaching of radionuclides from the vitrified waste, should it come into contact with water, [1]."

Jan 1, 2008

By Roberto Parra

The wear and corrosion phenomena in the furnace lining of the ferrous and non ferrous pyrometallurgical processes are complex problems where chemical, interfacial and mechanical phenomena are presents. The characteristics of the processes determine the conditions to which these materials are submitted, where the thermal conditions reached during the operation is one of the most important parameter. Assuming that all the degradation phenomena are thermal activated, the rate of the different steps of the wear mechanism will depend on the thermal field in the lining. In view to apply the independent physicochemical knowledge of degradation mechanisms to the analysis and design of furnace lining the methodology of the Nodal Wear Model (NWM) was done. It combines the mathematical modelling of the heat transfer in the lining with the physicochemical control equation for the wear-corrosion phenomena. The NWM has been applied to different examples: theoretical analysis, laboratory scale test and industrial applications. We present in this paper the theoretical background of the model and two examples of applications: the sole of an electric furnace and the earth of a blast furnace.

Jan 1, 2006

By Ian M. Ritchie

Cementation or metal displacement reactions such as Cu2+ + Fe Cu + Fe2+ are among the oldest known hydrometallurgical reactions. They are still used in the recovery of some metals and in the purification of process liquors and waste water streams. However, they are often more complex than the stoichiometric reaction would suggest because they involve the simultaneous deposition of one metal onto a second which is dissolving. For example, sometimes a cementation will not take place, even though it is thermodynamically favoured. On other occasions, a cementation reaction will start but come to a halt as the depositing metal blankets the reacting surface. On yet other occasions, side reactions, catalyzed by the deposit, can be important. In this paper, the electrochemical basis of cementation reactions is described. The conditions for each of the complications encountered in these reactions are described and illustrated by examples drawn from a number of hydrometallurgical processes. The cementation reaction between activated carbon and gold thiosulfate is also briefly described, this reaction being unusual in that no dissolution of the carbon occurs.

Jan 1, 2003

By Yong Hwan, Wang Jian-Jun, Cai Jiu-Ju, Chen Chun-Xia

"The quantity of residual-heat and its recovery in some Chinese sinter plants are investigated. The main factors affecting energy consumption are analyzed using exergy analysis combining energy level analysis. It is indicated that the “gradation recovery and cascade utilize” of discharged gas and sinter residual heat in different temperature is the direction and the available approach to reduce energy consumption of the sinter process. Taking an iron& steel enterprise as an example, the three-ranked scheme of residual-heat recovery is put forward: ?Part of the sinter gas is used for warm-up and dryness; ?The high-temperature part of the cooler and exhaust-heat boiler are actualized as a closed-circuit, which can produce high-quality steam to generate electricity. ?The waste air in low-temperature part is introduced to sintering machine to support combustion. According to the CDQ which can recover the coal heat, the assumption of pot-recovery is put forward to replace the belt cooler. The two equipments of residual-heat recovery are analyzed in the aspect of energy consumption and CO2 reduction.1. IntroductionEnergy consumption in sintering is only inferior to iron-making in iron& steel enterprises, accounting for 10%~20% of the total energy consumption. A lot of residual heat is produced during sintering, and mostly from the sinter ore and waste gas. Sensible heat of hot sinter ore and discharged gas have accounted for 60%[1] (equals to 40 kgce/t-ore), which are the key point of sintering waste heat recovery. Discharge gas of sintering is mostly composed of flue gas deriving from sinter bed’s combustion, and the content distribution of H2O and O2 and the temperature of the gas along the length of belt-type sintering are shown in Figure1[2,3]. Currently, the sensible heat of hot sinter ore is mainly recovered by circular cooler and cooled by blasting air: the temperature of cooled discharge gas brings down from 350? to about 100? along with the decrease of sinter ore temperature. It is significant to recovery and reuse the waste heat as 4000~6000m3 discharge gas per ton of ore can be produced"

Jan 1, 2008

By H. Y. Cheng

A pulse column solvent extraction system was evaluated as an alternative to mixer-settlers for the separation and purification of rare earths. The column tested had an inside diameter of 44.5 mm and had 36 sieve plates with a free area of 25%. Pulsing was provided pneumatically using a solenoid valve controlled by a timer so that both pulse amplitude and frequency could be varied. Feed to the column was a mixed rare earth chloride solution containing 10 g RE L-1. The extractant was 5% Ionquest® 801 in Shellsol 2037 diluent. Hydraulic performance of the pulse column was excellent with no propensity towards stable emulsions or crud formation under normal operating conditions. The column was operated in organic-continuous mode with flow rates chosen so that yttrium and the heavy rare earths were extracted with high efficiency while the light rare earths were rejected. Yttrium extraction varied from 83 to 99.2%. Concentration profiles were measured in both the aqueous and organic phases, and, from this data, the height of a transfer unit (HTU), the mass transfer coefficient (Kxa) and the continuous-phase axial dispersion coefficient (Ey) were computed. The HTU ranged from 17-92 an which is within the range of values reported for other (non rare earth) pulse column systems.

Jan 1, 1992

By Tiruttani Munikamal, Suresh Sundarraj

"A numerical model of the induction hardening process of steel cranks has been developed and the predicted results of temperature and phase distribution during this solid state phase transformation process are verified with experimental data from the literature. This heat treatment process involves heating the crank to the austenitic temperature range followed by rapid quenching in water to harden the surface of the crank. The model has been developed using ABAQUS, commercial FEA software. The formation of martensite, pearlite, and retained austenite phases are modeled and implemented through a user defined function in ABAQUS. A sensitivity study on the various process parameters affecting the amount of phase distribution has been carried out.IntroductionThe type of surface and sub-surface microstructure as well as the residual stresses that are present in a component after manufacturing, significantly affects it fatigue performance. The wear resistance of the automotive components such as crankshaft, gears, camshaft and bearings depends on the surface hardness. In order to achieve the surface hardness, these steel components are subjected to a type of quench hardening heat treatment process. There are several heat treatment processes available for the industrial application to improve the mechanical properties of the final part. Case hardening using induction heating is one of the widely used industrial techniques for improving the surface microstructure of a steel component. It consists of two stages i.e. induction heating cycle, followed by quenching in a fluid medium (usually water or oil)"

Jan 1, 2012

By P. Chris Pistorius

Calcium treatment of alumina inclusions, to convert the alumina to molten or partially molten calcium aluminates, is a well-established treatment for steel, to improve the castability of aluminium-killed steel. However, the role of magnesium in calcium-treated steel is not fully clear, nor is the origin of the several percent of magnesium oxide that is often present in calcium-treated inclusions. To study this, steel was sampled after calcium treatment at an industrial steel plant, and the inclusions identified by energy-dispersive X-ray microanalysis (EDX) on polished sections of the samples (analysing the samples in a scanning electron microscope). The predicted fraction liquid in the inclusion was estimated from the ternary alumina-magnesia-lime phase diagram. Inclusions with higher CaO contents generally had lower MgO contents, indicating that the calcium wire is not the origin of the magnesium in the inclusions; this was also confirmed by wet chemical analysis of the calcium wire. Instead, it appears that magnesium-alumina spinel inclusions form during extended ladle contact after aluminium killing and before calcium treatment. While such spinels have been stated to cause poor castability (clogging the submerged-entry nozzle), it is clear that calcium treatment successfully modifies the spinel inclusions to mixed alumina-lime-magnesia inclusions, where the magnesia content contributes substantially to liquefaction of the inclusions: for typical MgO contents of around 10%, the range of Ca:O ratios which yield liquid (or partially liquid) inclusions is extended substantially to lower Ca:O ratios.

Jan 1, 2006