Search Documents

Most of the world's zinc metal is produced via the roast- leach-electrowinning (RLE) process. The process is well established, but most of the sulphur in the sphalerite concentrates reports in the acid, which has to be stored and/or sold. There are significant incentives to develop a simpler process with much reduced acid generation. Ferric ion is a well known oxidant for most sulphides, in particular sphalerite, and it converts the sulphide to elemental sulphur. Based on stoichiometry, however, the amount of ferric ion needed to achieve acceptable zinc extractions is prohibitive for downstream zinc recovery from the leach solutions. The process suggested here makes use of less-than-stoichiometric ferric sulphate additions because the ferric ion is regenerated by sparging SO2/O2 mixtures. This regeneration can be effected in-situ in the leach vessel or outside the leach vessel. An example of the application of this new process is presented for a Canadian sphalerite concentrate assaying 60% Zn. The effects of temperature, ferric concentration and ferric ion regeneration are presented. Options to recover zinc from the leach solution are also briefly discussed.

Jan 1, 2000

By J. Avraamides

Some operational difficulties have been encountered in the transfer of carbon-in-pulp technology to Australian conditions. Many gold mines? are located in remote and arid areas where the available ground water is highly saline. There is a gradual depletion of free milling oxidised gold ore reserves resulting in the necessity to treat deeper primary sulphide .deposits which can be refractory. Some near-surface ore-bodies and tailing dumps are contaminated by natural vegetative matter which can interfere with the adsorption of gold from the cyanided pulp,. Advances which have been? made include potable water conservation in elution, a new type of regeneration kiln, inter-stage screens, alternative leaching systems transportable carbon-in-pulp plants and efficient open-cut mining methods. Academic and applied research is well supported by government and industry and the results are normally rapidly disseminated and put into practice by the gold mining industry.

Jan 1, 1989

By G. Sterzik, W. A. Jankola, T. L. Salway, D. J. McKay

At Trail, British Columbia, Cominco's zinc leaching and solution purification processes include direct pressure leaching of zinc concentrates, leaching of fume from the lead smelter, leaching of calcine and electrolyte purification. These processes have been adapted to match the unique characteristics of Cominco's integrated zinc and lead operations. Recent modifications include changes to the purification process and iron-residue handling circuits. In 1997, a new five-compartment autoclave, complete with ancillary equipment, was installed in the pressure leaching plant. This paper discusses these changes, the current flowsheet and further improvements.

Jan 1, 2000

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modem technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example of a European approach to these matters the paper presents Outokumpu' s response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modern technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example ofa European approach to these matters the paper presents Outokumpu's response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By Suswnu Makino

Sumitomo Metal Mining developed a new nickel refining process ( Matte Chlorine Leach Electrowinning process) based on chlorine leach and electrowinning technologies. After the pilot plant study, the commercial plant with design capacity of 24,000 tonnes per year was constructed and has been successfully operated since August, 1992. During the practice of the past three years, great deals of improvement have been achieved. Through these operations the MCLE process has been demonstrated to be one of the most superior processes in the world with nickel recovery, productivity, cathode quality and working environment. Today the refinery product capacity is increased to 30,000 tonnes per year. This paper describes the equipments and operation of the Sumitomo MCLE process.

Jan 1, 1996

By Norbert Hort, Karl Ulrich Kainer, Carsten Blawert, Daniel Fechner

"With the development of new heat resistant magnesium alloys, the automotive industry has introduced several parts to the drive train. The rising number of large magnesium components will result in a higher quantity of automotive post consumer scrap and the changing legislation will force car manufacturers to take magnesium recycling into consideration. So far post consumer scrap has not been used for magnesium alloy production. Quite a reasonable amount of automotive scrap is likely to end up in a mixed light metal shredder fraction. The separation of mixed magnesium scrap according to several alloys is complex. Therefore secondary magnesium alloys made from blended post consumer scrap would be useful. For this work a matrix of potential recycling alloys was prepared by chill casting and high pressure die casting. The materials were investigated for their microstructure, mechanical properties, heat resistance and corrosion properties. The results will be presented in this paper.IntroductionWithin the last ten to fifteen years several heavy magnesium parts have been assembled in passenger cars, such as gear box housings and crank cases [1, 2]. Reasons are the lately developed new heat resistant alloys and the increasing responsibility of automotive manufacturers to reduce the vehicles weight and thereby CO2 emissions. The latter is pushed by international legislation [3, 4]. The rising quantity of magnesium in automobiles will result in an increasing amount of so called post consumer scrap at the end of the vehicles life.So far magnesium recycling was done only for clean scrap that is free from impurities, contaminations and sorted according to a chemical composition or a single alloy respectively [5- 15]. The latter is also called class 1 scrap and mainly consists of sprues and runners from magnesium die casters [15, 16]. For the upcoming automotive post consumer scrap the materials quality strongly depends on the way end of life vehicles are treated. By proper dismantling of old cars, the bigger magnesium components could be collected and possibly treated similar to class 1 scrap [15]. Up to date automotive manufacturers have no uniform recycling system for end of live vehicles. Most probably a considerable quantity of old cars will be shredded. The resulting light metal shredder fraction will contain aluminium and magnesium scrap, both from several alloys. A separation of mixed magnesium and aluminium scrap is feasible according to [17]. Other authors claimed that the grade of separation of magnesium from aluminium is still not sufficient for a proper industrial recycling process of magnesium post consumer scrap [15, 16]. If an automatic sorting is possible it will probably be very expensive [18]. Therefore, so far the main use of post consumer scrap has been the steel desulphurisation and aluminium production [15]. The use of post consumer scrap for magnesium alloy production has been considered already by [15] and [16] but some problems have to be approached."

Jan 1, 2008

By Moenster J. A., M. J. Sankovitch

Doe Run's Buick Smelter was converted from a primary lead smelter to a secondary lead smelter in 1991. The recycling facility was designed to produce 60,000 tons of refined lead per year from 110,000 tons of spent starting-lighting-ignition (SLI) batteries and 10,000 tons of lead contained in drosses and scrap. Since commissioning, Buick's refined lead output has steadily increased to exceed 120,000 tons for 1999. The production gains have been the result of continuous process improvements, empowerment of the workforee, and development of additional scrap lead streams. The production gains were accomplished while setting industry standards for employee safety, reducing plant environmental emissions and employee blood leads, achieving ISO 9002 certification, and expanding product lines to meet customer requirements. This paper highlights Buick's major accomplishments through the 1990's.

Jan 1, 2000

By Kandipati Sreenivasarao

Ion flotation is a promising separation process for continuously removing toxic metal ions from dilute process effluents. After treating the effluent with appropriate surfactant(s), the metal- bearing species adsorb onto the surface of rising gas bubbles and can be collected as foams. Suitable collectors have been identified for most of the elements of the periodic table. However, a better understanding of the thermodynamic, kinetic and engineering principles that determine the performance of ion flotation systems would facilitate commercial utilization of this technology. A model system of sodium dodecylsulfate-ethanol has been studied for the removal of Cu (11) from dilute solutions, using laboratory-scale flotation columns. This paper reports the effects of the air flow rate, solution height, foam drainage zone height and col1ector:metal ion ratio on the flotation kinetics, ultimate recovery of metal, flotation product grade, foam losses and effluent quality. Preliminary results for Pb (11) removal are also reported.

Jan 1, 1993

By Nobuyuki Higashiyama, Ikuo Yonezu

"Hydrogen-absorbing alloys containing rare-earth elements are used in high capacity nickel-metal hydride secondary batteries,' hydrogen storage systems for portable fuel cells, and refrigeration systems. New hydrogen-absorbing alloys containing rare-earth elements have also been developed and introduced into these applications. High performance in nickel-metal hydride secondary batteries is strongly demanded because of the remarkable advancements in portable electric appliances. A large hydrogen absorption capacity, high electrochemical reactivity and superior corrosion resistance in an alkaline solution are required for hydrogen-absorbing alloys used in nickel-metal hydride batteries. The aim of this investigation is to improve the performance of conventional LaNi5 type hydrogen-absorbing alloys. For example, Mm(Ni-Co-Al-Mn)„ type hydrogen-absorbing alloys with various non-stoichiometric compositions were developed. In addition, a new process of rapid quenching process was applied for preparing these hydrogen-absorbing alloys in order to improve their performance.IntroductionRecently, the trend in electronic appliances toward portability has increased the demand for high capacity of secondary batteries as power sources. Since nickel-metal hydride batteries were first commercialized in 1990 in Japan, they have become increasingly popular as power sources for cellular phones, portable computers, electric shavers, and other, products.The performance of a nickel-metal hydride battery, such as its discharge capacity, high rate capability, and charge-discharge cycle life, strongly depends on the characteristics of the hydrogen-absorbing alloy negative electrode. Many types of hydrogen-absorbing alloys have been developed so far. For a hydrogen absorbing alloy to be used as the negative electrode material, (1) it must allow a large amount of hydrogen to be absorbed and desorbed in an alkaline solution, (2) its reaction rate should be high, and. (3) it must have long term durability under repeated charge-discharge cycling. However, LaNi5, a typical rare earth-nickel type alloy, shows significant capacity deterioration during repeated charge-discharge cycling. Therefore the first step in its development was to obtain sufficient corrosion resistance of the LaNi5 alloy for its use as an electrode material. A partial replacement of nickel with cobalt and a substitution of the lanthanum- content with misch metal (Mm), a mixture of rare earth elements such as lanthanum, cerium, praseodymium and neodymium, were very useful in improving the charge-discharge cycle life. However, the discharge capacity of the alloy was still not sufficient for a practical battery. A study of the effect of the partial substitution of aluminum and manganese showed that the best alloy composition was Mm(Ni-Co-Al-Mn)x, as follows.The stoichiometry x of Mm(Ni-Co-Al-Mn)x largely affects the discharge capacity and cycle life. Theose alloys with non-stoichiometric alloys with the compositions of [Mm(Ni-Co-AMn)x: 4.7<x<4.8] have a large capacity and a long cycle life. Nogami' et al. reported that 'a non-stoichiometric alloy with a Mm(Ni-Co-Al-Mn)x (x=4.76) composition showed approximately 10% higher discharge capacity than the stoichiometric alloy (x=5) [1] and greater influence of x on the electrochemical properties of multi-component AB„ type hydrogen-absorbing alloys for batteries."

Jan 1, 2000

By D. W. Hoey

Eight years use of the ISA Process is reviewed and current design and operations described. Nodern Technology used for impurity control and disposal as well as the use of mechanised electrode handling equipment, cell voltage monitoring, cell insulation and an efficient contact bar system are described. Improvements achieved in terms of energy usage and plant productivity are detailed.

Jan 1, 1987

By Kandipati Sreenivasarao

A promising method for removing heavy metal ions from dilute effluents is ion- or precipitate- flotation, in which a suitable collector is added to form hydrophobic metal-collector complexes or compounds that can be collected as foams. We have successfully removed Cu(II), Cd(II), and Pb(ll) from dilute solutions using sodium dodecylsulfate and ethanol as collector and frother respectively. However the process would not be economically viable unless the collector could be recycled, and the heavy metals recovered in a concentrated, preferably marketable, form from the foams. We investigated four different methods to decompose heavy metal-dodecylsulfate complexes, namely precipitation of hydroxides, precipitation of sulfides, chemical stripping, and electrolysis. We compare the performance of these methods. In each case the observed behavior is related to known thermodynamic data, and potential applications are discussed.

Jan 1, 1995

By R. K. F. Lam

Unacceptable levels of impurity were noted in high purity chromium melting. Analysis of recent melting data determined that oxygen content in chromium is the critical parameter. Thermodynamics studies identify zirconia to be the most stable oxide in the presence of liquid chromium, followed by alumina and silica. Iron oxide reacts readily with liquid Cr. A certain degree of chemical reaction between liquid chromium and oxides does occur, contamination by the crucible is therefore unavoidable. Equilibrium constants indicate that a chromium oxide addition decreases &apos;ceramic dissolution and reduces impurity contamination. Safe operating conditions with oxygen content between 1190 ppm and 2500 ppm were identified. Additions of chromium oxide (Cr2O3) of 161 grams and 264 grams to liquid chromium yielded acceptable levels of impurity, and oxygen content was respectively increased to 1624 ppm and 2 179 ppm. A new process of melting high purity chromium with chromium oxide addition for controlling the activity of Cr2O3 is recommended.

Jan 1, 1997

By M. Bhattacharya, A. Dutta, P. Barat

"Pinning of dislocations at nanosized obstacles like precipitates, voids and bubbles, is a crucial mechanism in the context of phenomena like hardening and creep. The interaction between such an obstacle and a dislocation is often explored at fundamental level by means of analytical tools, atomistic simulations and finite element methods. Nevertheless, such studies fail to predict the effect on the overall plasticity on account of insufficient information about the underlying statistics of this process comprising a large number of dislocations and obstacles in a system. Here we propose a new statistical approach, where the statistics of pinning at idealized spherical obstacles is explored by taking into account the generalized size distribution of the obstacle along with the dislocation density within a three-dimensional framework. The application of this approach has been demonstrated for dislocation pinning at nanovoids in neutron irradiated type 316-stainless steel.IntroductionPresence of nanoscale obstacles like precipitates, voids and bubbles play a crucial role in determining the deformation behavior of a crystalline solid on account of the interactions between the line defects and such localized obstacles. In the context of the glide motion of dislocations, the obstacles can offer resistance to a moving dislocation, thereby causing a hardening effect [l-3]. In some other cases, inclusions like voids and bubbles can affect the rate of dislocation climb through diffusive [4] and non-diffusive [5] mechanisms. Over the last few decades, numerous studies have been performed to gain an insight of the dislocation-obstacle interactions at a fundamental level. These include the interactions responsible for the hardening effect, in addition to those pertaining to the non-conservative motion of dislocations.Although the elementary mechanisms of the various dislocation-obstacle interactions have been vastly explored and understood by means of analytical theory and numerical simulations, it remains difficult to quantitatively understand their effects on the macroscopic deformation behavior. This is due to the fact that their influence on the gross plastic deformation of a bulk sample would be the collective outcome of a large ensemble of such interactions. As a result, it becomes infeasible to predict the bulk deformation behavior of a material until the statistics of pinning of the dislocations at the localized obstacles is available. In the context of precipitate hardening, some well known attempts to extract the pinning-statistics were made by Friedel-Fleischer [6] and Mott [7] by analytical means, which were later tested through simplified 2-dimensional in-silica modeling [8]."

Jan 1, 2014

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the process, to the subsequent cleaning of the gas. and to the use of the heat extracted from the gas. The method of reducing the effect of acidic sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms?are discussed. The development of indirect recuperators using air, water or steam cooling, made possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process? conditions".

Jan 1, 1992

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the ,process, to the subsequent cleaning of the gas and to the use of the heat extracted from the gas. The method of reducing the effect of acidic ,sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms are discussed. The development of indirect recuperators using air, water or steam cooling, made &apos;possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process conditions".

Jan 1, 1992

By Dean David

The evaluation of a new mineral sands prospect with unusual characteristics is described, The heavy minerals are very fine grained, have comparatively low average specific gravity (3.6) and are altered. Poor performance by conventional processing techniques made it necessary to trace the response of the major minerals during the separation processes, QEM*SEM® was used to quantify mineral volumetric abundances and mineral locking in magnetic and gravity separation products.

Jan 1, 1989

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By Takayoshi Fujii, Mitsumasa Hoshi, Chikashi Suenaga, Yoshiaki Suzuki

"In a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major - restructuring efforts since 1993.One of its themes was the shift from a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 metric tons per year of copper) by adopting such measures as improvements in pneumatic concentrate dryers, the concentrate feeding system, concentrate burners, the furnace cooling system, and a new cryogenic oxygen plant was constructed.With a view to realizing high matte grade operation (at 65%Cu) and increasing the concentrate feeding rate, further steps were taken the capacity of waste heat boiler was expanded and technical improvements were added, including optimization of the smelting reaction in the furnace shaft. As a result, the smelting capacity, as of the year 2000, has increased to 450,000 metric tons per year of copper.IntroductionThe feed rate to the flash furnace was doubled to 140 t/h from 70 t/h in 1996. Teething problems, as a result of the renovation, were almost solved by the end of 1996, and the operation of the single furnace operation has become stable.The main theme was the shift from a two-flash furnaces operation to a single-furnace operation to maintain the production capacity at the same level, namely 330,000 metric tons of copper per year. Then, in a bid to further renovate the Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, further enhancement of the flash furnace's productivity was planned.The purpose of this plan was to raise the copper production capacity to 450,000 mtpy building on the potentialities of existing plants and without installing new equipment."

Jan 1, 2000