Search Documents

By Phillip B. Messersmith, Emmanuel P. Giannelis

"A versatile in-situ polymerization approach is described for the synthesis of polymerceramic nanocomposites consisting of two-dimensional layers of mica-type silicate (MTS) within polymer matrices. Functionalized, organically modified mica-type silicates (OMTS) were used to promote delamination/dispersion of the host layers and initiate polymerization of organic rrionomer. Epoxy nanocomposites prepared in this manner exhibit substantial modulus reinforcement at low silicate loadings. The water vapor permeability of the poly(?-caprolactone) nanocomposite containing 4.8% silicate by volume was reduced by nearly an order of magnitude compared to pure poly (?-caprolactone).IntroductionPolymer matrix nanocomposites are a relatively new class of materials with dimensions typically in the range of 1-100 nm.1 In general, because of the ultrafine phase dimensions involved, nanocomposites exhibit new and improved properties when compared to their micro- or macrocomposite counterparts. We as well as others are currently investigating the design, synthesis and characterization of polymer-ceramic nanocomposites. Our effort, in particular, has focused on the use of mica-type silicates (MTS) with various thermoplastic and thermosetting matrices.2-5MTS's belong to the general family of 2: 1 layered silicates. Their crystal structure consists of layers of two silica tetrahedral sheets fused to an edge-shared octahedral sheet of either aluminum or magnesium hydroxide. Stacking of the layers leads to a regular van der Waals gap or interlayer.6 Isomorphic substitution within the layers generates negative charges that are counterbalanced by cations residing in the interlayers. Although the natural forms of MTS's usually contain hydrated Na+ or K+ ions, ion exchange reactions with organic cations (e.g. alkylammonium ions) can render the normally hydrophilic MTS's organophilic."

Jan 1, 1994

By M. Potesser

After the primary or secondary lead production the bullion lead is remelted and charged into a vessel with following refining process. The removing of arsenic, antimony and tin takes place by salt slags or oxidizing gases like air or pure oxygen. Due to the increasing lead price, Messer Austria GmbH in cooperation with the institute of Nonferrous Metallurgy at the University of Leoben have developed a new process named OXIPOT for the refining of tin, arsenic and antimony. The OXIPOT process is in principle based on purging technology with a ceramic or steel purging device. This leads to an increased retention time of the refining products due to the deeper bath level and an optimized specific reaction volume concerning the bubble size. This paper describes the process, pilot plant, and thermodynamic calculations for the optimization concerning the selectivity of element removal.

Jan 1, 2008

By Florian Kongoli

The optimal operation of the blast furnace depends considerably on the properties of the sinter fed into the furnace. As a result, the optimization of the sintering processes has a direct effect on the overall effectiveness of the iron making processes. In order to produce a good sinter special care needs to be taken in order to assure it has a good permeability and reducibility and it is able to retain these properties for a certain time. If the sinter starts to melt down early in the upper part of the blast furnace, where its solid state reduction is essential, permeability decreases, the gas channels get blocked, reductibility diminishes and serious problems may also follow. Among the factors that influences the above mentioned sinter properties are the oxygen potential and fluxing components. Nevertheless, their effect on the phase relations during sintering and sinter reduction conditions has not yet entirely clarified and confusion exists in literature. This quantification becomes even more important today where many new minor components such as Al2O3 and MgO enter the sinter through raw materials. This work quantifies the effect of oxygen potential and fluxing components such as alumina and magnesia on the liquidus and phase relations of the sinter primary melts in the iron rich portion of CaO-FeO-Fe2O3-SiO2 system at sintering conditions. This is carried out by the means of new type of industrial diagrams in the form of Fe/CaO vs. SiO2 that can directly help the optimization of the sintering processes.

Jan 1, 2006

By D. M. Jones

In May 1999 the first campaign of the BHP San Manuel flash smelting furnace (FSF) will be concluded after having set world records for both campaign length and tonnage smelted for an Outokumpu copper flash smelting furnace. This paper reviews planned process and equipment modifications including: The installation of a new 36,000 mt concentrate storage facility; replacement of the existing dryer electrostatic precipitator with a baghouse; modification of the FSF dry charge bin and feed system to achieve mass flow and uniform feed to the concentrate burner; modifications to the FSF and its ancillary cooling systems; modifications to the waste heat boiler and offgas handling system to increase gas handling capacity and improve process efficiency;- and improvements to the FSF fugitive gas collection system. A brief review of the planning and execution of the scheduled 45 day shutdown is also given.

Jan 1, 1999

By Ricardo Ponce

In recent years, ENAMI implemented modernisation plans at its two smelters in order to meet the government's environmental regulations introduced in the early 1990s. The modernisation plans defined the new SO2 and particulates emission targets, deadlines for compliance, and the revised treatment capacities of the smelters. At Las Ventanas smelter, the principal process change consisted of eliminating the reverberatory furnace. All the smelter feed is currently processed in a 4m diameter, 14m long Teniente Converter, using up to 34% oxygen enriched air. Dry concentrate is injected into the bath through tuyeres. A fuel oil burner compensates for any process heat deficiency. The Teniente Converter high copper content slag is cleaned in an electric furnace. This furnace is also used to melt internal reverts. This paper will discuss the successful operation of the slag cleaning electric furnace.

Jan 1, 1999

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By M. Oliazadeh

The present study was performed to develop a process for solvent extraction of molybdenum and cobalt from an acidic solution generated by an electrodeposition process of nanocrystalline cobalt alloys. Solvent extraction is a common practice in hydrometallurgical and refining processes to produce metals; however its application for separation of molybdenum and cobalt from this specific solution is new, because molybdenum and cobalt are not commonly associated together in nature. Five commercial organic extractants were examined for extraction of cobalt and molybdenum from synthetic acidic solutions with pH ranging from 1 to 5. Preliminary results showed that at pH 2, any of the Cyanex 923, Alamine 336, Aliquat 336 and Hostarex A327 could be used to extract 99% of molybdenum from solutions, while from pH 3 to 5, Aliquat 336 was able to extract about 100% of molybdenum. Cobalt extraction, on the other hand, varied from 15% to 23% at pH 3 and 30% to 53% at pH 2 using different extractants. Based on results obtained, Aliquat 336 was applied on mixed solutions of cobalt and molybdenum at various pHs. The results showed that molybdenum could be extracted as much as 99% from a mixture of molybdenum and cobalt at acidic pHs, while less than 1% of cobalt was separated at pH 2 to 4 simultaneously.

Jan 1, 2003

By Manfred K. Walther

"Tests were conducted on instrumented plates cast in the Abex Experimental Foundry to compare recorded solidification histories with results computed for corresponding models simulated with the C.A.S.T. program. The first plate was cast of low alloy steel and the second of carbon steel with a graphite chill at one end. Both were cast in molds of bonded silica sand. Temperature histories were recorded in the castings, molds and chill. Exceptionally good agreement was achieved between computed and experimental data. Other investigators will find the results useful as a benchmark against which they can compare the results of their own calculations.IntroductionSince the early 1970's our foundry engineers have used both two- and three-dimensional versions of the G.A.S.T. program to gain knowledge of the solidification process [1,2,3]. Study of the computed data gave insight as to how the rigging and risering of specific castings might be changed or adjusted to improve quality and yield. New schemes based on such analyses were then recommended for implementation on the foundry floor. The degree of success of the new practice was subsequently evaluated after the part had been poured, shaken out and examined. Similar conditions were noted in the sectioned castings whenever porosity and voids had been predicted by the computations. Appropriate modifications, when found successful in the model, were applied to the process. This led to a reduction, if not complete elimination, of the defects. Such results gave credence to the use of these programs as an aid in the production of better castings.Earlier investigations on simple shapes revealed excellent correlation between output derived with the G.A.S.T. program and exact solutions. Results also compared favorably with data calculated using other codes as reported in the literature [4] and summarized in the Appendix. However, since the computer program had not been verified by direct experiment, it was decided to run instrumented tests to check the theoretical predictions with actual measurements."

Jan 1, 1986

By K. Iwami, K. Abe

"Onahama Smelter and Refinery has been operated-since 1965 arid currently produces 243,000 metric tons per year of cathode copper. The Onahama tankhouse consists of conventional-type No.1 and 2 tankhouses with the capacity of 123,000 metric tons per year and No.3 tankhouse with 120,000 metric tons per year, adopting jumbo tank system, using hazelett anode respectively.In October, 1996, for the purpose of improving the - anode verticality, new anode copper body press machine has been installed in No.1, 2 tankhouses; by increasing Walker type anode copper weight by 35kg to 365kg. Consequently, it is possible to raise current density from 191 to 222 A/m2 and the No.1 and 2 tankhouses capacity was increased by 15,000 metric tons per year to 138,000 metric tons per year.At present, the refining capacity is 258,000 metric tons per year in total including No.3 tankhouse.This figure is the largest one in Japan.IntroductionSince the Onaham tankhouse was put into operation in 1965, the cathode copper production has increase with much labor cost saving.The following two cases to increase Walker type anode copper weight by 35kg to 365kg were studied.a) To increase the cathode copper production by raising current density.b) To save the labor cost by prolonging the anode cycle in order to decrease the exchanging time of electrodes.So the electrolytic tests were carried out to confirm· the effect of current efficiency, cathode copper quality and working conditions for space adjustment.As a result, we concluded that it was indispensable to introduce the anode body press machine to keep usual current efficiency and cathode copper quality with same workers, and to be possible to increase cathode copper production.In addition, the high-speed press machine was needed to maintain same working time and which specifications were decided through various investigations. In October 1996, the new anode body press machine made by Kawazoe Machine Works, Ltd. has been installed in No.1 tankhouse."

Jan 1, 2000

By S. de Vries, B. Wasmund, J. Metric, N. Voerrnann, S. Kasinger

Gulf Chemical & Metallurgical Corporation (GCMC) operates a circular DC electric smelting furnace to treat nickel and cobalt bearing residues at its plant in Freeport, Texas. The furnace, originally built by others, has experienced problems including runouts through the hearth and the lower sidewall. Hatch has designed several improvements to the furnace to alleviate these problems. The single anode at the centre of the hearth was replaced with a patented system of twelve air-cooled copper anodes evenly spaced around the furnace lower sidewall. The DC power supply comprises two transformers and two rectifiers operating in parallel. The water-cooling system on the bottom and lower sidewall shell plates was replaced with an air-cooling system using copper cooling fins. The existing row of water-cooled copper coolers in the metal bath zone was re-designed for greater heat removal capacity and better element joint sealing, and a new row of water-cooled copper coolers was added to cool both the alumina bath and freeboard zones. The existing water-cooled metal and alumina tapblocks were also re-designed for more robust cooling. A binding system was added to provide refractory compression that reduces the risk of liquid leaks. Finally, the furnace tilting frame was relocated to the top of the furnace where it is less likely to be damaged.

Jan 1, 2000

By Evan Jamieson

The conditions under which various iron(III) oxy-hydroxides phases precipitate from iron(III) chloride and sulfate solutions at ambient temperatures (<60°C) are reviewed. Many of these precipitates are slow settling and gelatinous but ultimately transform into other more stable or crystalline phases. The phase that forms depends upon the rate of precipitation and pH. A comparison has been made of the iron(III) oxides formed upon the neutralisation of various iron(III) solutions with caustic, slaked lime or slaked magnesia which provide different rates of neutralisation and slowly dissolving solids with localised high pH. Mössbauer spectra of ferrihydrites precipitated under these different conditions are compared and interpreted. Particular attention is paid to the settling rate and settled volume which is likely to relate to industrial thickener and filter performance. It is shown that in pure chloride solutions, poorly settling ferrihydrite is usually produced at 20oC regardless of the choice of base. However in sulfate solutions fast settling precipitates are produced using lime and magnesia but not with caustic. In mixed chloride/sulfate solutions, optimum settling rates occur when the molar ratio of [SO4]2to Fe3+ is about 1:1 and when the sulfate concentration is <0.20 M. It is proposed that ?dense amorphous basic iron sulfate? or well-ordered ferrihydrite is formed on slowly dissolving lime or magnesia surfaces. Implications for industrial liquors are considered.

Jan 1, 2003

By Rongshan Qin, Dengfu Chen, Yan Zhao, Mingtu Ma, Yang Li, Xinming Wan

A two dimensional cellular automaton (CA) model coupled with finite element (FE) method has been developed for simulating the formation of solidified microstructure during beam blank continuous casting, which represents columnar and equiaxed dendrites growth in the case of detailed secondary cooling boundary conditions. In this model, a new adaptive mesh division is proposed to couple CA cubic lattice and irregular FE mesh of beam blank. A double-accuracy liner interpolation method is employed to obtain micro CA temperature field via macro FE calculation. The nucleation process and the velocity of dendrite tip are calculated by continuous nucleation model and KGT model, respectively. Moreover, the preferred orientation of dendrite growth is determined using a probabilistic model. The effects of super heat and casting speed on the microstructure characteristics are analyzed. This model can be applied to optimize processing parameters for beam blank continuous casting basing on microstructure evaluation.

Jan 1, 2015

By František Molnar, Zsolt Szentirmai, Juraj Schmiedl, Felix Sekula

"Hydrometallurgical nickel production in Sered Nickel Plant (Slovakia) that treated roasted Albanian ore left behind a considerable amount of the solid leaching residue. About 6 million tons of this fine-powder residue containing approximately 52 wt.% of iron in the form of oxides is to the present day stored in a stockpile. However, its iron content makes it a potentially interesting secondary raw material for iron production. This secondary raw material is not, unfortunately, suitable for direct treatment in iron and steelmaking processes.This paper presents results of the laboratory tests of pyrometallurgical method of processing of the leaching residue by its roasting and subsequent refining melting. The objective of the selective reducing agglomeration roasting was to reduce iron oxides and to simultaneously avoid reduction of chromium oxides and silica. Refining melting is carried out in an inert atmosphere. The products of melting are technically pure iron and slag.IntroductionThe leaching residue stockpiled on waste dump near already non-existing Nickel Plant Sered, Slovakia, is considered to be one of the most important environmental burdens in this country. The 40-years of an on-going effort focused on finding the methods for extracting metals and thus remove the waste dump have not been successful [1,4,5,6]. From the literature survey it is evident that past investigations have been following three main routes:1.Removal of chromium by mineral processing methods prior to its metallurgical treatment to achieve final chromium concentrations below 0.3 wt.%.2.Pelletization of solid leaching residue and its subsequent reduction in blast furnace and steelmaking plant and simultaneous removal of chromium.3.Pelletization of solid leaching residue followed by metallurgical processing of preliminary reduced semi-product in electric arc furnace (EAF) accompanied by partial reduction of chromium."

Jan 1, 2008

By Dale T. Peters

Conductivity, both electrical and thermal, are attributes accounting for about 70% of the applications of copper and its alloys. This paper presents results of on-going research into two new applications that depend on copper&apos;s excellent conductivity. The Copper Development Association (CDA), together with materials and motor company partners, is working toward a solution to the key problem preventing pressure die casting copper for the conductor bar/end ring structure of the induction motor rotor, i.e., lack of a durable high-temperature mold material. Work is showing that a combination of high- temperature materials and elevated temperature processing gives much improved mold life compared to die steels. Substitution of copper for aluminum in the rotor can result in a 20% decrease in electrical losses in motors consuming 35% of electrical power generated in the U.S. The second development uses the excellent thermal conductivity of several high-strength high-copper alloys to simultaneously improve productivity and part quality in the injection molding of plastic parts.

Jan 1, 1999

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"In the present study, different types of cathode ray tube (CRT) glasses were examined by sequential extraction combined with TCLP to provide possible explanations for how Pb and Ba leach out from the waste CRT glasses and to give possible reasons for why they leach out. Sequential extraction results showed that Pb and Ba in the CRT glasses dominanfly presented as the residual fraction. The exchangeable fractions of Pb and Ba were extremely low, less than 0.01 % of the total content, but they were higher than those required by the regulation limits, 5 and 100 mg/L for Pb and Ba, respectively. TCLP tests of the original CRT glasses and CRT glasses residues after each step of sequential extraction demonstrated that the extremely high leaching toxicity of CRT glasses mainly caused by its exchangeable and carbonate fractions of Pb and Ba.IntroductionIn recent years, the amount of cathode ray tube (CRT) contained monitors or TV sets in the market were sharply reduced, since they were substituted by novel and better electronic and electric equipments such as LCD and PDP, leaving huge amount of end-of-life CRTs. 50-85% of the total weight of this kind of computer monitor or a TV set is glass[1,2], which was classified to three categories according to their chemical compositions: black & white glass (BW), color panel glass (CP) and color funnel glass (CF)[3]. In order to provide shielding from X-rays generated during the picture projection process, lead, barium and strontium oxides were used in the glass. In general, a color CRT contains 1.6-3.2 kg of lead . Therefore, these glasses have attracted wide and tense attention due to the potential risk to the environment and human health."

Jan 1, 2011

By C. D. Chapman

Current regulations regarding the landfill disposal of asbestos containing wastes are inadequate to ensure there are no ground water or airborne emissions. Accordingly, there is growing recognition that asbestos wastes can only be safely disposed of by using techniques that destroy the hazardous fibres. An innovative high-temperature plasma arc technology (The MAGRAM Process) is being developed for the recovery of magnesium metal from asbestos together with supplementary magnesia containing feedstock. The furnace will operate in. open bath mode with aluminium and/or ferrosilicon being employed as reductant. An important advantage of the process is that magnesium vapour within the furnace will be generated close to atmospheric pressure rather than at reduced pressure under which existing processes operate. Thermodynamic modelling work has been undertaken to define the range of slag composition and furnace temperature under which magnesium production at atmospheric pressure is feasible. The effect of slag chemistry, reductant addition, and temperature on product quality and yield have also been investigated and key aspects have been tested on bench scale. A 300 kW pilot plasma furnace unit has been employed for the treatment of calcined asbestos wastes. Aspects of design and operation of the unit are detailed. Acknowledgement: This work is substantially financially supported by the European Communities under the Industrial and Materials Technologies (Brite EuRam H) Research and Development programme.

Jan 1, 1995

By S. Ferlay

"The main purpose of the ZIMA VAL project (Label EUREKA EU1367 and LIFE ENV/F/000278) is to demonstrate industrial scale recovery and recycling of the main components of used dry batteries (zinc, manganese dioxide, mercury, and stainless steel) into high added value products. The originality of the ZIMA VAL process resides in:1- the use of hydrometallurgy2- alkaline treatment implementation (highly selective) for zinc and mercury3- electrochemical recovery of high quality products.4- the recycling of all the battery components (zinc, mercury, manganese dioxide, stainless steel) ·5- low operating and investment costs.The process consists of physical classification, mechanical dismantling, hydrometallurgy and electrochemistry. The purpose of the demonstration plant in FALAISE (Calvados - France) is to define the technical and technological parameters of an industrial unit for the treatment of 2400 tonnes per year of used batteries."

Jan 1, 2000

By G. Johnston, J. Greenly, R. G. Buchheit, D. C. McIntyre, R. Muenchausen, D. J. Rej, R W. Stinnett

"Rapid thermal treatment of materials using high energy, high flux, pulsed ion beams can produce modified surface layers with unique microstrutures and properties. High energy ions loose their energy during the slowing down process in the workpiece and thus deposit their energy continuously over a depth of a few microns. The deposition of energy can lead to melting and in some causes ablation of the heated layer. Because the pulse duration of the ion beams is typically only 50-200 ns, steep thermal gradients generated during heating facilitate rapid cooling (107K/sec-108K/sec) of the treated layer by thermal diffusion into the underlying material. Rapid heating and cooling of materials can generate surface layers with non-equilibrium amorphous or nano-crystalline microstructures that exhibit increased hardness, wear resistance, and corrosion resistance. Pulsed ion beam treatment can also lead to surface smoothening or can be used to mix thin « 1 11m thick) coatings into underlying substrates. Pulsed ion beams can be generated using existing ""flashover"" ion source technology which is capable of producing single shot, mixed C, H, and O ion beams with beam cross sections of approximately 100 cm2 and energy fluxes up to 100 J/ cm2. Recent advances in repetitive high energy pulsed power technology and development of magnetically confined anode plasma ion sources have facilitated the development of ion beam systems that generate single species beams that pulse continuously at 120 shots/second. These capabilities will allow rapid treatment of large surface area workpieces at low cost.IntroductionThe rapid solidification of liquid materials can create unique materials and material microstructures that often have properties that can lead to enhanced performance. Rapid solidification processing of the surfaces of materials using continuous and pulsed laser beams (laser glazing) has been explored for over 20 years (1-5). Advances in high energy, pulsed electron and ion beam technologies over the past decade have provided rapid thermal treatment techniques that may be less expensive to impliment than laser surface treatment for many surface modification applications (6). High energy pulsed ion beams have recently been used to harden aluminum(7), copper(8) and tool steel surfaces (6,9), increase corrosion resistance of Al alloys (6), mix coatings into underlying substrates (10), and create amorphous films (11,12)."

Jan 1, 1994

By Yuzo Hiroshige, Kiyotaka Tahara, Hiroki Hatayama, Masaharu Motoshita, Tomohiko Akahori

Large amount of rare earth metals is stored in the used electric products. Hitachi has started to develop the environment-friendly process for rare earth metals recovery from used magnets. We report here the environmental impact of our process, in comparison with the conventional recycle process utilizing solvent extraction. As an evaluation method, Life-cycle Impact assessment Method based on Endpoint modeling ver.2 (LIME2) developed by the National Institute of Advanced Industrial Science and Technology (AIST) in Japan is applied. It was found that the environmental impact of the new process was more than that of the conventional process. For further reduction of its environmental impact, minimization of energy consumption to operate the equipment was most effective. Decreasing the amount of magnesium, used as an extractant, and the improvement of the extraction rate of rare earth metals were also considered as specific options for reducing energy consumption in the plant development.

Jan 1, 2014

By Peter K. Liaw, Niann-i Yu, Wei Zhao

"For a plain-weave Nicalon ™ fiber fabric-reinforced silicon carbide (SiC) ceramic composite, little attentation has been paid to the effect of fabric stacking sequence on its mechanical behavior. In this paper, fiber-fabric stacking sequence effects on the elastic stress distributions, ceramic matrix-cracking stress, effective elastic moduli, and flexural strengths of laminated flexural test bars are quantified. A quantification model is established based on the combination of classical laminated plate theories and a fiber undulation model developed by Chou et al. A FORTRAN program is compiled to implement the modeling, which can be run in a SUN work station. The mechanical performance of a continuous fiber-reinforced ceramic-matrix composite (CFCC) with a [0/30/60] lay-up was analyzed and predicted. The variation in the fiber-fabric stacking sequence can vary the elastic stress distributions along the thickness direction of specimens, magnitude of ceramic matrix-cracking stress, effective elastic moduli of the laminate, and crack initiation sites as well as fracture modes. Moreover, all these factors contribute to scatter in flexural strengths of the CFCC.I. IntroductionWith enhanced fracture toughness and the ability of non-catastrophic (graceful) failure behavior, CFCCs are currently under evaluation for high-temperature structural applications in heat exchangers, combustors, hot-gas filters, boilers components, first walls and high-heat flux surfaces gas turbines, space vehicles and nuclear reactors.[1-8] Extensive applications of CFCCs by industry are still hampered by an insufficient understanding of the mechanical behavior, and sometimes, the lack of a well-developed and widely accepted design philosophy, in addition to the high-production costs."

Jan 1, 1998