Search Documents

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By Pengfu Tan

Lead blast-furnace bullion cools to near its freezing point in an operation known as copper drossing or hot drossing usually contains 0.02-0.06% copper. The removal of this copper is usually carried out in a batch operation known as sulfur drossing. Sulfur is stirred into the bullion at temperatures near its freezing point, and the dross of copper and lead sulfides that floats to the surface is skimmed off manually. A thermodynamic model has been developed to simulate the copper drossing. The phase diagram of Pb-Cu-S system has been calculated, and the effects of the process parameters, such as temperature, copper content, and sulfur content, on the drossing process have been simulated and discussed.

Jan 1, 2006

By Clara María Lamus Molina

The following minerals found in the residual black sands from gold mining in El Bagre Antioquia (Colombia) were identified as having major economic interest: Ilmenite (FeTiO3), with an average of 49% of TiO2, frequently altered presenting crowns; lamellaes of rutile and alteration textures; titanomagnetite with up to 25% of TiO2; magnetite (Fe3O4) in individual grains or associated with others minerals as hematite and ferromagnesian silicates rutile (TiO2) with considerable quantities of Nb2O5(0.1-3.7%Wt); zircon (ZrSiO4) with 66%Wt of ZrO2 and monazite with an average of 63.43%Wt of REE, this frequently associated to xenotime and thorite forming textures as little drops. Analysis in EPMA and SEM/EDS showed percentages of minor elements and traces, thereby clearly establishing the applications of these minerals in diverse industries. Furthermore, a detailed granumetric study of the different minerals and textural relationships among them also allowed for establishing the basis for possible processing and exploitation.

Jan 1, 2006

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By Zhao-cheng Liu

Iron oxide red pigment powders of high quality were synthesized from pyrite cinders. Iron ox-ide red pigment powders were synthesized by hydrothermal method from the precursor of Fe(OH)3 and Fe(OH)2 colloid, which were obtained after ammonia solution reacted with acidic leaching solution produced by the reaction of pyrite cinders with sulfuric acid. Effects of reaction concentration, reaction temperature, reaction time, pH value and n(Fe2+)/n(Fe3+) on main properties of oxide iron red were studied by experiments. The prepared particles were characterized by means of X-ray diffraction (XRD) and scanning electron microscope(SEM). The results revealed that the synthesized iron oxide red particles were _-Fe2O3 and pseudocubic with particle size of 0.50~0.75µm. Furthermore, the quality of iron oxide red pigment powders reached the first grade of national standard (GB1863-89 ).

Jan 1, 2009

By Sergio N. Monteiro

Polymeric composites reinforced with natural fibers are increasingly been used in several engineering applications, from automotive parts to building construction elements. In addition to the relatively low cost, the natural fibers are also appraised by their renewable and biodegradable characteristics. Fibers extracted from the crust of coconut fruits, also known as coir fibers have been investigated for a possible use in composite materials. In the present work, the coirfiber/polyester matrix interfacial strength was evaluated by means of pullout tests. The variation of the pullout tensile stress vs. the embedded coir fiber length permitted to determine the critical fiber length and, thus, to calculate the interfacial strength. Observations by SEM complemented the results from pullout tests, indicating that coir fibers have a potential for application aspolymeric composites that could replace conventional materials such as wooden and gypsumpanels.

Jan 1, 2006

By WU Jian-hui

Keywords: metallic material; nickel powder; thermal decomposition; precursor; fibrillar powder; nanometer scale; passivation treatment The precursor thermal decomposition process of fibrillar nanometer scale nickel powder and passivation treatment of obtained powder are investigated, and the composition and morphology of the products are characterized by use of IR, TGA/DTA, XRD and SEM. The results show that the precursor morphology is a decisive factor to the product morphology of the nickel powder. The morphology of the product derived at low decomposing temperature is irregular. The nickel powders produced at the temperature higher than 480 coheres seriously. The product particles are reunited with the decomposition time prolong. The powder prepared under the optimal condition is fibrillar like woolen yarn; the grain diameter is less than 50nm.

Jan 1, 2005

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By M. Potesser

One of the main targets in the automotive mass industry and supplying industry is the weight reduction of the vehicle for decrease of the fuel consumption. For that reason combinations of different kinds of materials and connections of, for example, steel and aluminium are developed or are already successfully field-tested. A determining factor concerning the quality assessment of the welded joint during hybrid welding is the characterization of the intermetallic Fe-Al layer regarding strength, hardness, morphology and mainly the different phases in which Fe occurs together with the Aluminum (FeAl, Fe2Al5, FeAl3.). A combination of conventional light microscopy, SEM - EDX - analysis, the usage of an atomic force microscope including a Nanoindenter and theoretical thermodynamic calculations turned out to be highly effective. Based on the attained results, the constitution of the intermetallic FeAl layer, influenced by silicon, manganese and zinc, can be predicted.

Jan 1, 2006

By Andreas Nolte

This paper includes a comprehensive report about the metallurgical utilisation of reusable products from electronic scrap recycling, car shredding industry, used glasses an various waste products, such as slimes and flue dusts, generated in a secondary copper smelter. Depending on the copper content, the type of copper compounds and the characteristics of accompanying substances, the materials are treated by smelting in furnaces, operating under reducing or oxidizing conditions. HKs pyro- and hydrometallurgical processes, blast furnaces, converters anode furnaces, tin lead alloy plant and tankhouse will be outlined. The reusable products are categorized according to the origin of the materials and then presented in the form of quantity and quality balances. Processing methods, process able quantities and quality requirements of inputs are described. The utilization degree of the most important metals (copper, tin, lead and zinc) is described with graphics. The report is rounded by information on operating licence according to the environmental regulations of the Federal Republic of Germany and data concerning supply and contracts

Jan 1, 1997

By Taegong Ryu

Nanosized tungsten powder was synthesized by the hydrogen reduction of ammonium paratungstate (APT) in thermal plasma. The effects of operating conditions on the product composition and particle size were investigated. The particle size of synthesized W powder was less than 30 nm in all cases tested. The sintering behavior of the synthesized powder (25 nm average size) was then investigated and compared with those of commercial W powder of 500 nm average size and W powder of 23 nm average size produced by milling the commercial powder. The sintering was done at 1400oC with various holding times. The hardness of the resulting compact from the synthesized W powder (315 VHN) was similar to that from the milled W powder (309 VHN), but the plasma-synthesized powder had a much lower tendency to form cracks. The compacts of both nanopowders were significantly harder than that of the commercial powder (192 VHN).

Jan 1, 2009

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By Youze Xu

The leaching and reduction of Cr(VI) in soils contaminated by chromium-containing slag were investigated with column experiments. The results showed that Cr(VI) concentration in leachate decreased from 988 mg L-1 to 407 mg L-1 after 7 days when water was used as leaching agent. However, Cr(VI) in leachate in culture medium treatment was not detected at above periods. In comparison, Cr(VI) concentration in leachate from autoclaved soil remained 398 mg L-1 at the end of experiment. The results indicated that the indigenous microorganism was capable of reducing Cr(VI). The amount of Cr(VI) reduction was 335 mg at the whole experiment period and the reduction rate was 67.09 mg d-1. Carbon supply showed minor effect on Cr(VI) reduction. However the reduction capability of Cr(VI) could be improved by combination of the carbon and the nitrogen. The optimal quantity was 5 g L-1 of yeast extract and 4 g L-1 of glucose.

Jan 1, 2009

By Napisporn Memongkol

Syntheses of Al-TiC-Al2O3 and Al-SiC-Al2O3 composites were obtained in situ by carbothermal reduction of mixtures of Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders. The reductions were carried out in a horizontal tube furnace under flow of inert gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of aluminum reinforce with titanium carbide and alumina and aluminum reinforce with silicon carbide and alumina. The effect of the reaction temperature (1000 o C ? 1200 o C) and condition of precursors on the Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders were investigated using XRD and SEM method. The synthesized products showed those composites with aluminum matrix and titanium carbide and alumina as reinforced phases and aluminum matrix and silicon carbide and alumina as a reinforced phase was formed.

Jan 1, 2006

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

By Zhi-xiang Cui

Effects of flux, vulcanizing agent and reductant on slag cleaning in new-type slag cleaning furnace (Φ3.6 × 8.1 m) were investigated under the conditions including smelting temperature of 1200 and 1250 °C, settling time of 30 and 60 min, and Fe/SiO2 of 1.7–1.9. The results show that addition of SiO2, B2O3 or CaF2 into original copper smelting slag can improve settling separation effect. Though no effect on copper recovery, addition of FeS can provide heat required by reaction with oxygen and reduce copper dissolution in spinel phase and slag. Copper content in discarded slag can be controlled at 0.26% under the optimum comprehensive conditions with ratio of oxygen to natural gas of 1.6.

By Natalya. N. Ankusheva

The problems of ore-bearing palaevolcanic structures in folded belts are actual because of their high productivity in nonferrous, ferrous and noble metals ores. Now relationships of location and conditions of formation for sulfide-massive and gold-bearing deposits are investigated very well in Urals. But carboniferous sulfide-barite mineralization, for example the barite veins in Arcaimsky palaevolcano are?nt studied enough now [3-5]. The purpose of this research is the studying of mineralogy and thermobarogeochemistry of barite from the hydrothermal veins. It will allow to determine the conditions of its formation and to compare it to the similar mineralization of others ore types.

Jan 1, 2006

By M. Faraji

Inclusions formed in a high-carbon, manganese-silicon killed plain steel (Fe-0.77C wt%) were studied. Various techniques were used to characterise the inclusions, and the latter were classified according to their chemical composition, size and morphology. The main constituent elements entering the inclusions were Mn, S, Al, and oxygen. Alongside MnS and some Al2O3 inclusions many non-metallic inclusions appeared in complex forms, consisting of silicates, sulphides and oxides. Duplex oxy-sulphides, mainly MnS combined with Al2O3, or SiO2 were the most common complex multiphase inclusions in this steel. The nanoindentation technique was used to assess and rate different types of inclusions and data of the hardness and elastic modulus of individual inclusions at room temperature are presented.

Jan 1, 2010

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By K. Morsi

Carbon nanotube (CNT) reinforced metallic composites have been recently generating significant scientific interest, due to their expected superior properties compared with other composites. Out of the metallic matrices investigated for reinforcement with CNTs, aluminum has received considerable attention. A major problem has been the dispersion of CNTs in metallic matrices. This paper discusses preliminary results on the mechanical dispersion of CNTs in aluminum powder, powder processing, stability and characterization of aluminum dispersed with CNTs at reinforcement levels equal to and below 5 wt.%.

Jan 1, 2009