Search Documents

By H. Yavuz

A Numerical modelling study using the two dimensional finite difference code "FLAC" was performed for investigating the ability of numerical modelling to predict the performance of yielding pillars. The model was verified by comparing the stress and deformation data obtained from a yield pillar trial application at Welbeck Colliery, a UK coal mine. Two entries with-a 10 m intervening pillar were modelled. Both for development and for side abutment loading stages, the vertical stress measurement data over the pillar and side abutment and deformation measurement data in the roof and floor of the trial entry were compared with the results obtained from the model. Two difficulties were encountered, unavailability of data for caved rock and for the yielding pillar material. These were overcome by back analysis to estimate the unknown field properties of the pillar material and caved rock from known properties of these materials. Results from this model are given and the predictive capability of a finite difference model for two entry yield pillar applications is discussed.

Jan 1, 2001

By Keith A. Heasley

Pillar recovery in deep coal mines with competent roof and floor can concentrate stresses and generate hazardous bumps. Actual calculation of the geologic strain energy released in association with these coal bumps has been rare, although energy release values have been utilized successfully for indicating burst potential in numerous hard- rock mines. This paper advances the current knowledge of energy release calculations as applied to coal bumps through an extensive analysis of an actual bump occurrence. The U.S.B.M, displacement- discontinuity code, MULSIM/NL, is used to produce a numerical model which generates stress, displacements and energy values associated with a pillar retreat section. This model is calibrated with actual field data, and then dissipated energy values from the model are examined as to their suit- ability for indicating bump potential. Ultimately, it is determined that prudent application of dissipated energy calculations can be used as a tool to investigate the coal bump potential of a mining plan or cut sequence.

Jan 1, 1990

By David H. Tang

Similar massive pillar failures were observed in two underground coal mines with different configurations of mine workings and overburden depths. Finite element models were used to analyze the causes and mechanisms of the pillar failure. The results of the analyses confirms the underground observation. For Case No. 1 the failure of coal pillar is mainly caused by a combined effect of smaller coal pillars under a large overburden and the interaction of multiple seam mining. For Case No. 2, the pillar failure was initiated by the weak roof rock but the ultimate pillar failure was caused by the splitting of pillars into very small size.

Jan 1, 1984

By Q. F. Wang

Spontaneous combustion hazard of loose coal in the top-coal caving region of entry affects the safety of the entry and top- caving longwall face seriously. In this paper, by combining on- site temperature tests with lab tests and numerical simulation, the characteristics of microcirculation close to the top-coal caving region are analyzed. A model for the temperature fields of the microcirculation in loose coal is presented. Based on this model, the temperature distribution and possible self-ignition region can be predicted. Further, the heat and mass transfers in microcirculation are studied. Finally, the mechanism of oxygenation during the spontaneous combustion of microcirculation in loose coal of the top-coal caving region of entries is put forward. The research results in this papa may provide ideas for the prevention and putting out of the fire caused by spontaneous combustion in the caving zone.

Jan 1, 2004

By S. I. Al-Ameen

Monolithic packing systems have gained in popularity as a gate side packing method, However, there has been no detailed investigation to assess their underground strength behaviour. This work includes the laboratory and in situ investigation for strength behaviour determined on various monolithic packing materials namely Tekpak-XX, Hydropak-20, Hydropak-30, Astrapak-3R, Flashpak, Thyssen pack and Aquablends. A simple technique for assessing the pack strength was developed at the laboratory by using a penetrometer, of which penetration resistance can be directly correlated with the uniaxial strength of the pack. The in situ strength investigations were made on core samples obtained from three pipes inserted inside the pack, while the penetration test were made on the pack surface. The in situ results indicated that the packing material develops an inconsistent strength on various part of the pack which was mainly related to an inadequate mixing of grouts inside the pack.

Jan 1, 1992

By Steve Signer

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining effected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

Jan 1, 2004

By Christopher Mark

The demographics and safety record of the pillar retreat segment of the U.S. coal industry was analyzed using statistics collected by the Mine Safety and Health Administration. Pillar recovery is practiced primarily by mines in Appalachia and the Midwest. Using 1993 data, the accident rates and productivity of a large sample of pillar re- mines were found to be similar to other room-and-pillar mines in the same geographic areas. Pillar recovery apparently accounts for about 10% of all U.S. underground production, but has been associated with about 25% of the mf and rib fatalities during 1989-96. However, of the 28 fatalities that were analyzed, only 4 occurred for which no citations were issued for violations of mining law. Nearly one- half of the fatal incidents occurred during the mining of the last lift or pushout. All four no-citation incidents occurred during the removal of the last lift during a "Christmas tree" extraction sequence.

Jan 1, 1997

At any given lime, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes in the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

This paper presents a two-dimensional numerical procedure which incorporates concepts related to the mechanics of strata deformation' as well as' empirical indices associated with subsidence engineering. Regional deformation data were employed in order to establish overburden deformation zones, while material properties were kept constant. Scaling of final displacements was based on empirically predicted values for subsidence and strain for the Appalachian coalfield. The model was validated with a number of regional case studies and predicted subsidence and strain curves were compared to those obtained using the semi-empirical influence function formulation developed by VPI&SU.

Jan 1, 1988

By Gift Makusha

Surface subsidence associated with coal mining activities in the Mpumalanga Province of South Africa changes the natural environment in several ways, and current challenges for mining companies include rehabilitation of the natural environment and the prevention of further degradation. To monitor the spatial and temporal evolution of surface subsidence, traditional fieldbased monitoring approaches such as GPS and spirit leveling are employed at a number of locations. However, the resulting measurements are point-based, and frequent revisitations are necessary to map the evolution of surface subsidence basins over time. To address these limitations, differential interferograms derived from repeat-pass satellite-borne synthetic aperture radar (SAR) systems were tested for their ability to measure and monitor surface deformation. The SAR data was captured by the European ERS-1 and ERS-2 satellite and covered a timeframe between 2008- 09-15 and 2008-09-15. The resulting interferograms revealed several features indicative of surface subsidence. Ground truth data confirmed the presence of a subsidence basin, detected using differential interferometry techniques during the 35-day period between April 12, 2008 and May 17, 2008; a maximum vertical deformation of 3.2 cm (1.3 in) was recorded. Interferometric monitoring revealed an eastward migration of the subsidence basin between June 2, 2008 and September 15, 2008 with an additional 4.7 cm (1.9 in) of subsidence observed. This migration coincides with the advance of the working face of the mine during this period. Finite element modeling will be performed in order to model the rates and evolution of surface subsidence haloes as underground mining advances. These presented results demonstrate the ability of interferometric synthetic aperture radar techniques to measure surface subsidence as well as the monitoring of the evolution of subsidence basins over time. This implies that the technique could be included, together with traditional field-based surveying techniques, in an operational monitoring system. With knowledge on deformation rates and subsidence basin evolution, informed decisions on current and future infrastructure development can be made and remedial actions and prevention strategies can be formulated for the problems associated with environmental degradation.

Jan 1, 2011

By Bruce K. Hebblewhit

Australia is well endowed with extensive reserves of thick underground coal scams, particularly in the range of 4.5m to 9m thicknesses. (For the purposes of this paper, thick scams are defined as being greater than 4.5m thick.) At the present time, the thickest, high production, high productivity underground mining operation in Australia operates at a maximum of approximately 4.8m using single pass longwall methods. In a number of instances, conventional' height operations are mining thick seam coal, effectively sterilising considerable reserves - either because of financial or technical risk concerns, or in some cases poorer quality coal at some horizons in the scam, UNSW has been involved in thick scam mining research over many years, most recently through an ACARP -funded project, jointly with the CMTE in Australia. A key part of that project involved the assessment of the relative geotechnical risks associated with the various methods under consideration. The methods were: single pass longwall; multi-slice descending longwall; soutirage and related caving methods (including the Chinese Longwall Top Coal Caving method (LTCC)): and hydraulic mining. A formal risk assessment process was adopted to review the risks, relative to a conventional 4m high longwall operation. This paper presents the findings of that risk review and discusses the geotechnical issues (and some possible solutions for risk management) which need to be dealt with in order to bring these methods to fruition in the context of the Australian coal industry environment.

Jan 1, 2001

By Guorui Feng, Min Zhang, Yi Luo, Jian Yang, Yujiang Zhang, Junwen Bai

"Safe mining of coal seam sandwiched between abandoned upper and lower room-and-pillared mines (ULPM) ·is increasingly becoming the focus of attention in recent years, which is closely related to the damage intensity of the upper and lower interburdens. The #7 seam with ULPM in Baijiazhuang coal mine was selected for this research. According to the mining and geological conditions, the vertical stress and plastic zone distributions were determined first by numerical simulation. Then, a theoretical model based on the elasti-plasticity theory was developed. The stress distribution and failure zone created in the interburden by mining the upper and lower seams were determined. Finally the feasibility of mining #7 seam between the abandoned upper and a lower seam was evaluated. The results show that: (1) the distributions of abutment pressure and plastic zone coincide, both of which can be used to evaluate the failure zone in ULPM. The failure zone penetrates the whole upper interburden, while only parts of the lower interburden fail. (2) the theoretical failure zone coincides with the maximum distribution zone of abutment pressure and plastic zone obtained by numerical simulation: the failure zone height in the lower interburden is less than its thickness, while that in the upper interburden is larger than its thickness. (3) the #7 seam is located in the failure zone created by the upper seam room-and-pillar mining, which leads to well-development fractures and blocky fragments in the roof, thereby it is unstabled. (4) when mining the #7 seam in the interburden, the key is to control the roof strata and proper support measures should be taken timely to ensure safe mining.INTRODUCTIONMany coal mines in China mine the thick, superior and easily mineable resources preferentially, while the thin, inferior and difficult-to-mine resources were abandoned (Chappells and Trentrnann, 2015; Zhenfu, 2012; Xu, et al., 2015; Guorui, 2009). As the results of deficient geological data and shortage of investment capital, the residual coal resources distributes in many mining areas in China.In recent years, many residual coal seams sandwiched between the abandoned upper and lower room-and-pillar mines (ULPM) were explored in Shanxi Province, especially in the mining area of Datang, Xishan and Luan (Figure.1). The reserves of residual coal seams in ULPM are considerable, increasingly becomes the focus of attention among scholars and engineers."

Jan 1, 2016

By Nikolaos Polysos

To drive and utilise gate roads economically requires accurate planning and risk assessment considering the variable geomechanical requirements. The geomechanical part of roadway planning is secured by geotechnical investigations of drill cores and geophysical borehole logging. The rock specific parameters determined in this way allow a statement about the quality (defomtation and strength characteristics) of the rock that has to be cut across. They set up the basis for a standardised rock assessment. Combined with the prevailing rock mechanical situation, technical boundary conditions for advance and support techniques can be identified already in the planning phase. Detailed geotechnical investigations prior to the planning and driving of roadways can lead to a technically and economically optimised roof support system. Geotechnical core logging and a standardised assessment scheme based on the data acquired will be introduced. Geophysical borehole logging methods provide additional physical data. Different methods and their validity, which may lead to a further improvement of the planning reliability, will also be presented. The geomechanical information gained and their relevance fir the planning will he illustrated. Keywords: rock classification, geotechnical rock parameters. geophysical well logs. support planning

Jan 1, 2002

By M. Afsari Nejad

A Transversely Elasto-Plastic Model was configured in FLAC (Fact Lagrangian Analysis of Continua) as a more realistic simulation of stratified and inclined strata behaviour examining surface subsidence above the inclined longwall panels (I ). The failure criterion employed was a modified Mohr-Coulomb failure criterion that assumed a variable cohesion, which changed with respect to the orientation of the plane of anisotropy . Using the proposed numerical modelling technique several longwall panels with different configurations were simulated. The results of both surface subsidence and horizontal displacements were validated against UK data using the Subsidence Engineer's Handbook (S.E.H) subsidence prediction method and the Influence Function Method (2). It was found from the research that the incite properties as well as laboratory to field reduction factors arc depth dependent. A set of relationships for calculation of anicotropic stiffness and strength parameters have been derived. The proposed modelling approach has been successfully applied to surface subsidence prediction for 3 collieries in the UK allowing the results of the simulation to he validated directly against measured data.

Jan 1, 1998

By Mietek Rataj

Installation of pre-tensioned Strand Bolts i.e. resin grouted cable bolts is very common now in Australian coal mines. A short historical development of this type of rock reinforcement is outlined Various systems have been developed to apply 20 to 25 tonnes of pre-load to these bolts but there are still some technical problems which have to be overcome. One of the major problems encountered is bleed off tension which is highly undesirable as required "over loading" rocks the immediate roof thus inducing fractures iii weak strata. The major reason for the loss of tension apart from the design of the tensioning jack, is the design of the conventionally used barrels and wedges. Due to a roof plate tilting during tensioning the cable moves out of the barrel centre which impedes proper positioning of the wedges and subsequent excessive return of the cable once load of the jack is released. This problem has been largely resolved by the design of a special barrel having a centralizing rim allowing for significant reduction of the toss of tension. KEYWORDS: Pre-tensioned Strand Bolts, Cable Bolts, Bleed off Tension, Tensioning Jack, Loss of Tension

Jan 1, 2002

By Kent D. Mctyer

Mining commenced at Tasman Mine in late 2006. The current method of mining is bord and pillar using continuous minerbolters and shuttle cars for first workings and secondary extraction using mobile roof supports. The two stage process was chosen to accommodate irregularly shaped coal deposits, allowing adjustments to be made to extraction ratios for better management of subsidence and to maximize the efficiency of the operation. Following the completion of the first three full/partial extraction panels, the mining method was changed due to variable caving. Another partial extraction method, referred to as the Duncan Method was adopted; it involves stripping the developed square pillars on four-sides on retreat to leave a load-bearing remnant coal pillar. The system of partial extraction has been successful in meeting safety, productivity, and subsidence targets.

Jan 1, 2011

By Ben L. Seegmiller

Specially truss systems? including the Intersection Truss®, Continuous Entry Truss®, Cutter Roof Truss® and Roktrus® have been used in many coal mines in the mid- west and western United States during the past four years. These truss systems offer greater strength and support than other standard trusses and many other support devices. Mining operations have found that speciality trusses can give effective long-term support in areas that must remain stable for many years. At some mines, the Intersection Truss® has become the most-widely accepted method of providing secondary support in potential problem areas. Other applications for specialty trusses have included longwall start- up and recovery rooms, arched roofs, access rock tunnels and tailgate entries.

Jan 1, 1990

By Kot Unrug

Fully grouted tensioned bolts provide a desirable compressive of laminated roof and bondage along the entire bolt length, at the same time the entire surface of the hole is protected against penetration of moisture. This is particularly important in shale strata, where, when left unprotected by a partial grout column, moisture penetrates to the annular space, and weathers rock around the bolt hole, having an easy access to the bedding planes which are strongly hydrophilic. The most desirable are thrust tensioned rebar bolts that can be installed with one procedure step, and can secure a desired pre-stressing. Such bolts have a forged conventional head and offer no hazard to miners in low clearance mines, whose number increase constantly due to the depletion of reserves in thicker seams. The presented field-testing program has been based on instrumented bolts allowing for monitoring of tension at installation and at a chosen time interval after. The tested system is based on rebar bolts installed with two speed Fosroc resin (fast at the top and stow at the bottom), and mechanical compression by the bolting machine at installation. Combination of several different washer -- plate arrangements have been tested. The results are reported with their interpretation, and recommendations directly towards strata control requirements, as well as the operational considerations for efficiency of installation.

Jan 1, 2002

By C. W. Bollier

In recent years, Peabody Coal Company has enjoyed a great amount of success using roof trussing as a secondary support system. Since 1975, over 180,000 trusses have been installed in 12 different Peabody mines with varying geological conditions. Projections from Peabody, and throughout the mining industry, indicate a continuous growth in the trussing principle for roof control. Peabody's primary supplier has sold over 1,000,000 trusses to 50 different mines throughout the country. (1) Roof trusses provide an improved means of controlling difficult roof conditions which, in turn, improves worker safety and mine production. Since the original development of the truss, (2) the only major modification to the trussing procedure has been the addition of the resin point anchor system in the mid-70's. The resin point anchor was the catalyst needed to provide a reliable anchor and create acceptance of the roof truss by both management and labor. Peabody began using trusses in their mines in 1975. For the first few years, most of the truss effort was geared toward determining proper anchorage, spacing, and gathering historical data. In recent years, Peabody's activities have centered on the development of improving trussing procedures. Through monitoring and trussing activities, a number of areas of improvement have been found.

Jan 1, 1982

By Kazem Oraee-Mirzamani

Blasting operations generate seismic effects in underground mines. These effects apply additional dynamic loads on the support system, which should bear both static and dynamic loads. Static loads are caused by the weight of the superincumbent strata, while dynamic loads occur as a result of blasting in the mining area. Identification of the origin and determination of the support system behavior in natural frequencies is crucial in assessing the stability of underground mines. This is because resonance occurs when a support is vibrated with its natural frequencies, which can cause a vibration with the maximum amplitude and subsequently cause extreme deformations. The mechanism of support system deformation during dynamic load displacement has been studied and numerical simulation for the impact of the dynamic loads on stability of supports is carried out using finite element method. The paper introduces a simple technique for improving stability and safety of mining operations. Results obtained and the methodology adopted in this research can help mining design engineers make decisions on adequate support for active mining operations.

Jan 1, 2011