Search Documents

By Kevin Jinrong Ma

Underground mines often experience roof falls in entries, crosscuts, and intersections of active mining sections, main travel ways, and belt entries. Roof fall heights greater than 20 ft (6 m) make re-bolting of the newly exposed roof dangerous and impractical. To protect mine personnel, belts, moving vehicles, and other facilities, mine operators typically install steel structures such as square or arch sets in the roof fall areas. Wood lagging is usually installed between the steel-sets to enclose the area and protect the entry from recurring falls. Usually the void space above the steel-sets and laggings is backfilled. However, backfilling high roof fall voids is costly, which causes some operators to leave the voids open. In this case, durability of wood over time and the capability of the steel-set and wood lagging to resist falling rocks are unknown. During the last few years, Keystone Mining Services, LLC (Jennmar Corporation affiliate engineering company) designed, tested, and developed an impact-resistant lagging system to protect steel-sets1. Various steel-sets protected with the impact-resistant lagging were approved by MSHA and installed in different underground roof fall rehabilitation projects. This paper presents (1) design, development, and laboratory testing of the patent-pending impact-resistant lagging panel, (2) steel-set design methodology according to the American Institute of Steel Construction (AISC) national standard, and (3) impact-resistant steel-set design method based on Law of Conservation of Energy. Two underground cases are reviewed to demonstrate the successful application of the impact-resistant lagging system.

Jan 1, 2011

By Rene Rodriguez

Sandstone paleo-channels encountered during coal mining operation can significantly slow down the advance in mining, and often completely shut-down coal mine production, with consequent extensive economic losses to the mine operator. Definition of the encountered channel usually involves intensive drilling; vertically from the surface and/or horizontally from underground vantage points. Coal operators with limited resources often resort to exploration by extending mine faces toward the channel. Both drilling and underground mining exploration are prohibitively expensive and usually provide only partial information about the location, size and shape of the sandstone channel. A low cost alternative which can also provide a more comprehensive picture of the channel is the application of Underground High Resolution Seismic Methods (UHRSM) developed and successfully tested by GECOH Exploration. UHRSM applies surface seismic reflection technology rotated as needed (usually 90 degrees) to accommodate the faces of the exposed channel, coal rib, or coal in front of the inclusion (sandstone channel, etc.). This entails placing high frequency seismic sources and geophones horizontally across these exposed faces. Refraction and reflection events from the front and back of the channel are isolated, analyzed and inverted, to calculate the channel's location and geometry. This paper presents a summary of the geophysical exploration technique and two case history examples where it was applied. In the first case, the accuracy of the technique was verified through subsequent mining. Mining is yet to commence in the second case. Both cases were applied to room-and-pillar nines where the irregular rib lines significantly extended the data processing effort. This suggests that UHRSM will find the easiest application when used along straight rib lines, but that is not a requisite to the application. The UHRSM should find ready application in longwall mining to delineate sandstone channels and other non-coal inclusions in the middle of the panels or ahead of the gate road faces.

Jan 1, 1994

By J. L. Condon

The Bureau of Mines, through in-house and contract research, monitored mountain bump-prone areas of the Olga #2 Mine, near Welch, WV, using microseismic techniques for 15 months during 1985 and 1986. During this period, two ground failures occurred that were considered "mountain bumps" owing to excessive stress buildups. One failure damaged the roof and 4 pillars around an intersection; the second failure, which released much greater energy, resulted in significant damage to over 100 coal pillars. Analysis of the microseismic data collected provided significant insights into the magnitude and location of each failure. The actual failure zone was clearly delineated prior to the mountain bump occurrences through analysis of source locations of each microseismicevent. Trends in cumulative rate plots indicated the onset of structural instability. Although the data could not be analyzed automatically, the significance of the data interpretation cannot be overemphasized. Microseismic monitoring of bump-prone areas can be successful in providing a means to actually observe the structural stability occurring in underground coal mines. This paper discusses data collection techniques, analysis methods, and implications of the monitoring technique, with special emphasis on actual data from two large mountain bumps in West Virginia.

Jan 1, 1987

By Richard G. Burdick

The Bureau of Mines', Denver Research Center has been conducting research for the past few years on the use of resistivity methods to locate abandoned mine workings. As this work has progressed, it is apparent that in some cases, in addition to detecting the old workings; stoping, precursive to surface subsidence has also been detected. This paper describes the Automated Resistivity method and discusses sites in Colorado. Wyoming. and Illinois where the subsidence phenomenon has been observed.

Jan 1, 1982

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990

By S. J. Jung

The goal of this research is to demonstrate how optimization methodology can be coupled with the finite element method for greater stability of underground mine openings. As a result of increasing mining depth and intersection of geologic discontinuities, mining environments are becoming more complex. Current design procedures are rapidly becoming inadequate. In this research, the finite element method has been coupled with optimization criteria to design more stable and safe underground openings

Jan 1, 1993

By Syd S. Peng

A total of 209 cases of subsidence data over longwall panels in 16 US coal seems have been collected and built into a subsidence database. The database is developed under MS Windows environment. It uses a very user-friendly menu driven system. The empirical formulae for a number of commonly used subsidence parameters have been derived from those collected subsidence data.

Jan 1, 1995

By J. Marc Coolen

Marrowbone Development Company operates a large drift mining complex in the central Appalachian coal field. In 1997, five continuous miner supersections produced close to 9 million tons of raw plant feed. All production is from the Coalburg seam, a 5 to 10 ft thick coal seam with multiple coal benches and shale binders. The immediate roof lithologies consist of laminated shales, sandstones, or a mixture of sandstones and shales. The mine area is bisected by the regional Warfield anticline and associated Warfield fault. Mining conditions vary considerably due to frequent changes in seam and roof geology. The following geological categories can be distinguished: 1) presence of coal riders in the immediate shale roof, 2) excessive seam slopes around the Warfield fault, 3) splay faults associated with the Warfield fault, 4) zones of abundant slickensides, 5) abrupt roof lithology changes (sandstone - shale), 6) splitting and merging of different benches of the Coalburg seam, 7) sandstone washouts, 8) excessive roof dilution, 9) pillar sizing problems due to seam anomalies (soft fireclay binders). Several examples of these features are discussed in detail. Also, their relationship to roof fall occurrences is evaluated. Early recognition of potentially adverse geological conditions is of prime importance for the economic viability of the mining plans. Detailed core drilling in advance of the mining faces and coordination of the core data with underground mapping are the main forecasting tools.

Jan 1, 1999

By David A. Newman

Severe roof control problems have plagued a West Virginia underground mine since its initial development in the late 1970's. Adverse roof conditions in the Eastern portion of the reserve result from a combination of mining: - perpendicular to the major principal horizontal stress direction, - near lineament intersections, - in areas where the ratio of horizontal stress to vertical stress exceeds 2.00 to 4.00, and - where laminated strata are present in the immediate roof. The focus of this study is to identify the engineering (mine orientation, roof safety factor) and geological parameters (lineament and horizontal stress orientation, horizontal to vertical stress ratio, and immediate roof lithology) causing poor roof conditions and to quantify their influence on projected mining conditions in the Western portion of the reserve Rose diagrams were used to illustrate the correlation between the orientation of eight hundred thirty-six (836) roof falls with that of forty-four (44) lineaments and the principal horizontal stress Similarly a composite map was used to demonstrate the relationship between roof falls and the ratio of horizontal stress to vertical stress The immediate roof strata across the property were categorized as either laminated or non-laminated based upon a thorough examination of one hundred sixty-two core logs. The presence or absence of fireclay, a rider coal, and carbonaceous shale was also noted because of the historic correlation with poor roof conditions. Rock strength and physical property tests were conducted on selected immediate roof strata recovered from coreholes drilled along the mains projected to the Western portion of the reserve Potential roof control problems in the Western reserve were quantified based upon the correlations developed by analyzing engineering and geological data The main conclusion is that laminated roof strata, the rider seam, and its associated fireclay will have the greatest influence on mining conditions. Roof problems attributable to horizontal stresses will not be as severe in the West due to an increase in overburden depth and corresponding decrease in the stress ratio. Recommendations are provided for mining orientation, the layout of mains and submains, panel location, and roof support based on intended service life.

Jan 1, 1999

By Gamal Rashed

Coal bump is a sudden manifestation of the release of strain energy stored in a coal pillar (Peng, 2008). It is a very serious mining hazard that adversely affects the safety and productivity of the mines. Several case histories in mining have described coal pillars or faces of coal failing violently with an accompanying ejection of debris and broken material into the working areas of the mine (Campoli, 1987; Osterwald, 1962; Peperakis, 1958; Garvey and Ozbay, 2013). These failures resulted in large losses of life and total collapses of entire mine panels (Chase, Zipf, and Mark, 1994; Zingano, Koppe, and Costa, 2004). There are questions in the literature about whether or not the coal itself plays a significant role in bump. Rice (1935) mentioned that structurally strong coal is one of the key factors for bump; however, the strength of the Pocahontas #3 coal seam is low, and it bumped. Moreover, it is not obvious in the literature whether the strength of the tested coal samples is the inherent strength or if it is influenced by the shape or the size of the specimen. The main objective of this paper is to answer the following question: To what extent does the mechanical properties of the coal have an impact on the potential for violent failure? The best approach to answer this question is to compare the mechanical properties of two kinds of coals from bump-prone (Utah coal-Sunnyside seam) and non-bump-prone (WV coal-Sewickley seam). This comparison includes uniaxial compressive strength, modulus of elasticity, shear strength (cohesion and friction angle), and the burst index.

Jan 1, 2014

By William J. Gray

The Roof Control Division of MSHA's Pittsburgh Safety and Health Technology Center has been conducting a program to evaluate methods employed by the U.S. coal mining industry during recovery of longwall faces. The objective of this effort is to provide information on safe and efficient roof control methods currently being used to recover longwall faces. In addition to a literature review and extensive contacts with MSHA and industry personnel, 14 mines were visited to observe firsthand various aspects of longwall recovery. It is hoped that the dissemination of this information will aid in the prevention of accidents and a reduction in costly downtime during recovery.

Jan 1, 1993

By S. F. Smith

Following a roof beam collapse on a major production district at the British Steel Corporation's Dragonby Iron Ore Mine, Scunthorpe, South Humberside, UK, rock mechanics investigations were undertaken in this room and pillar operation to assess the stability of workings throughout all the underground mine area. Over a four year period room convergence and roof sag were monitored in different mining areas and various junction configurations in order to assess and compare the relative movement of the strata resulting from mining activities, where varying rock bolt lengths and patterns have been utilised. The paper, after shortly describing geological aspects and mining methods, presents the research procedure adopted together with the instrumentation employed and discusses the results obtained during these investigations.

Jan 1, 1995

By Anton Sroka

The German hard coal production predominantly derives from underground multiseam mining activities. Beside common surface damages, ?inner mine damages? on underground infrastructures (i.e. main roads, cross cuts and shafts) due to mining excavations occur to an increasing extent. As these "inner mine damages" dramatically increased because of the development towards high performance longwall mining technologies, this matter raised to be a severe problem concerning mining economics. To protect durable and long lasting underground infrastructures, precautionary measures such as suitable mine layouts, adapted planning of mining operations and moderate face advances have to be considered. Some examples of "inner mine damages" recorded by means of mine surveying methods are given in this paper. An empirical-mathematical model based on the principles of mining subsidence engineering methods will be introduced. This model allows to minimize ?inner mine damages? and helps to support and optimize mining processes.

Jan 1, 1999

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By Cosmo P. Fazio

Remote control roof bolting is approaching reality with the continued improvement of a number of components and subsystems being developed by The Bendix Corporation under sponsorship of the U.S. Bureau of Mines and the U.S. Department of Energy. The era of remote control research in roof bolting was initiated by the USBM in June of 1973 with the award of a contract to Bendix Corporation to design and build a roof bolt bender/inserter device. One year later in June of 1974, the Bureau awarded five parallel R&D contracts to develop a longer-than-seam-height flexible roof drill. The Bendix flexible drill design has been the most successful of the five, has been thoroughly tested in both laboratory and underground situations, and has been incorporated into a number of machine applications along with the roof bolt inserter. The purpose of this paper is to discuss the advantages of remote control bolting from both a safety and productivity standpoint. Applications of the flexible drill and roof bolt inserter on a number of government and industry supported programs are used to illustrate the advances being made toward the goal of remote control.

Jan 1, 1982

By P. Forrest

Based on the results of mathematical analysis, photoelastic modelling, and case studies, the mechanisms of longwall under- mining interaction has been thoroughly investigated. The effects of using yield pillars in combination with rigid pillars in lower seam mine design have been found to provide significant improvement in ground conditions during undermining. Off- setting of solemnized longwall panel entries relative to upper-seam remnant structures has proven to be effective in alleviating adverse stress conditions.

Jan 1, 1988

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Russell C. Frith

This paper presents recent findings concerning longwall caving mechanisms relating to Australian mining conditions and their effect upon longwall support requirements and behaviour. The findings arc based on a program of intensive hydraulic support monitoring in a variety of Australian mining conditions coupled with geotechnical observations. Results from the study illustrate periodic weighting cycles of varying severity and these are related to the overlying geology in terms of the strength of individual strata units, their thickness and proximity to the longwall extraction. Several different caving mechanisms are identified which contribute to periodic weighting cycles. The importance of recognising weighting cycles in relation to the operation of the longwall face will be discussed in detail. Longwall support design methods are critically examined in relation to the case histories of the monitoring program. The applicability of the said design methods to Australian coal mining conditions is discussed and an outline of design considerations to facilitate productive longwalling is presented. Overall, the paper only "scratches the surface" of the work currently being undertaken by ACIRL in this area, and the findings of that work.

Jan 1, 1992

By Christopher Mark

The Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. The study described in this paper was performed in a 1200 ft long, experimental headgate section which contained three pillar designs: - a three-entry, yield-abutment pillar' system, - a four-entry, yield-yield-abutment pillar system, and - a five-entry, all-yield pillar system. As the longwall mined by the experimental section, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The results of the study indicate that the all-yield system performed at least as well as, and probably better than, the two abutment pillar systems.

Jan 1, 1988

By Kenneth Rigsby

Black Mountain Resources' Highlands Mine No. I is a full extraction room and pillar operation located in Harlan County, Kentucky. Black Mountain extracts the 0.9 to 1.1 meter (36- to 42-inch) thick Owl Scam that is situated 60 to 70 meters (200 to 235 ft) above the longwall panels of the abandoned Arch No. 37 Mine, in the 3.4 meter (I I ft) thick Harlan Scam. In the areas where full extraction has taken place, the overburden above the Owl Seam ranges from 60 to 430 meters (200 to 1,400 ft). A short room and pillar panel was developed above an extracted longwall panel to test the selected pillar size, to evaluate support systems, and to verify the shape of the subsidence profile over the recovery end of the depleted longwall panel. It is over the recovery end that Highlands Mine No. I would access the Owl Seam reserves that exist above the No. 37 Mine. Black Mountain selected pillars sizes to be employed above the longwalls based on the ability to fully extract a pillar employing extended cuts. After a mechanical testing program was completed and mine behavior and top disturbance were observed in the test panel, John T. Boyd Company (BOYD) verified pillar stability and designed support systems. BOYD previously designed No. 37 Mine's gate pillars and studied subsidence and gob formation over its longwall panels; this effort aided the analysis of overburden movement and pillar integrity at Highlands Mine No. 1.

Jan 1, 2003