Search Documents

By M. Heger

February 2, 1999 marks a milestone in earth-moving technology at the San Miguel Lignite Mine. It was on that date that The North American Coal Corporation (NAC) took delivery of three Leica Dozer 2000 GPS grade control systems for use on its bulldozers. The primary reason for the purchase of these grade control systems was to prove that GPS technology could safely and economically be utilized on heavy equipment to assist operators in defining grades. If these properties were successfully demonstrated, the ultimate vision of the project was to expand the system to a point were GPS would become the primary means of providing grade control information to the mine’s heavy equipment operators. Twenty nine months and more than $500,000 later this vision was realized when the final bulldozer operating at the San Miguel Lignite Mine was equipped with Dozer 2000. Presently North American Coal has a total of nine Dozer 2000 GPS grade control systems at San Miguel providing cut and fill information to operators 24 hours a day. These grade control systems have allowed the San Miguel operation to increase safety, reduce costs, improve operator attitude, and better ensure environmental compliance. This article discusses both the nature of these benefits and some of the issues that had to be dealt with along the way.

Jan 1, 2002

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin, Derek Maishman

Ground freezing was utilized to provide complete stability of the excavation face and complete groundwater cut-off for the jacking of the three tunnel boxes for the Interstate 90 / Interstate 93 approach to the Fort Point Channel crossing. Through a wide range of geological conditions and large buried obstructions, the freezing provided complete stability of the face so that a 11.5 m (38 ft) high free standing vertical face could be mined without the need for any additional face support. Obstructions were incorporated into the massive frozen ground matrix, and held in place so that they could be excavated with a minimum of disturbance. The freezing provided an absolute groundwater cut-off, and permitted the work to be done without disturbance to the active rail system immediately above. With the use of instrumentation such as borehole thermocouples, the effectiveness of the freezing was guaranteed and the jacking proceeded with complete confidence and assurance of the ground conditions ahead.

Jan 1, 2001

By C. O. Brawner, J. Kalejta II

The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than about 45°. As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result with less rock fall capacity. The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented.

Jan 1, 2002

By Steve Kral

In the United States, the U.S. Environmental Protection Agency (EPA) is set to implement its Tier 2 air quality standards governing high-horsepower, off-road diesel engines. The regulations take effect in January2006. In Europe, similar standards, called Stages, are due to take effect about the same time. And other markets, such as Japan and Australia, have their own standards on tap. Tier 2 standards will further reduce the amount of nitrogen oxide (NOX), sulfur dioxide (SO2), diesel particulate matter (DPM), carbon monoxide (CO) and hydrocarbons off-highway diesel engines are allowed to emit. And even more restrictive Tier 4 standards are due in 2011. The upshot is that operators of high-horsepower engines, particularly in mining, will begin using in their new off-road haul trucks, excavators, shovels and other mining machines diesel engines that are designed to meet these more stringent standards.

Jan 1, 2004

By Kevin G. Stricklin

Introduction Continuous monitoring techniques have been used in the US and abroad for many years. A continuous miner has a monitor that measures methane and automatically gives a warning if the methane exceeds 1%. It deenergizes the continuous mining machine automatically at a maximum concentration of 2%. Main fans are also continually monitored to ensure operation. Alarms may also be given at a remote location should a fan slow or stop. The systems being developed can continuously monitor various gases and equipment throughout the mine and transmit pertinent data to a surface monitoring station. At this station, conditions throughout the mine can be monitored and, in some instances, controlled. These are known as Mine Wide Monitoring Systems (MWMS). History The use of environmental monitoring systems began in 1976 when a federal court approved the petition of modification to use belt air at the face. The first mine to receive a modification did install a system to supplement existing safeguards. Later, the Mine Safety and Health Administration (MSHA) and the US Bureau of Mines (USBM) conducted tests dealing with the use of belt air. Findings from these tests are being used to set guidelines as requirements of a petition. These requirements include: • Velocity of air has to be 0.25 to 1.5 m/sec (50 to 300 fpm); • Monitors will be installed at each belt drive and tailpiece and at intervals not to exceed 610 m (2000 ft); and • An alarm level of 10 ppm, above the ambient level is appropriate. The early uses of environmental monitoring could only be used outby the last open crosscut. That may be a reason for an initial slow growth of these systems. In June 1982, MSHA began evaluating systems that could be used in returns to ensure that monitoring systems being used in areas where permissible equipment is required does not of itself pose an explosion hazard. This is known as the Mine Wide Monitoring Systems Evaluations and Sensor Classification program. The evaluations and classifications granted are based on electric currents and voltages. Use of mine wide monitoring systems The environmental aspect of MWMS in today's coal industry deals with carbon monoxide (CO), methane (CH4), and air velocity. Just as all mines are different and encounter different problems, the MWMS are diverse and can be used to provide necessary data in all areas of coal mines. Mine operators in an ultragassy seam, for example, may be concerned with monitoring methane, while a mine that used diesel equipment may want to continuously monitor for diesel contaminants. In a mine with roof fall problems, airflow monitors may be helpful as an indication of whether the air is flowing in its normal course and at its normal volume. Today's MWMS can monitor any or all of these parameters. Most systems can be expanded as mining needs require. For example, a mine is now being monitored for methane and five years from now CO monitoring would help increase safety. It may be possible to use the same system by adding additional equipment. In the US, 30 environmental monitoring systems were installed from May 1985 through May 1986. In 1984 and 1985, there were 38 and 44 environmental monitoring systems in operation, respectively. Due to mine closings, 11 of these are no longer in use. However, the number of mines using environmental monitoring systems increased to 63. Use of these systems are not limited to any geographic area or

Jan 9, 1987

By P. D?Elia

Following a study by NIOSH on the availability of teams in the U.S. as well as existing training sites and their capabilities, the Penn State University, leaders of the Pittsburgh Section of SME, providers of mine rescue equipment, and industry sponsors united to establish and make fully functional a student mine rescue team at Penn State University. With the growth of MERD and mine rescue competitive events at Missouri S&T, the Mine Training and Technology Center in PA, and at Colorado School of Mines Edgar Mine, a critical mass of effective training venues were made available to help student teams progress and develop mine rescue skills. The challenges to be met in creating and developing a student mine rescue team will be discussed. The rewards from this type of effort will be the quick capability of graduates from mining engineering programs to be involved in not only mining operations, but industry mine rescue teams and other leadership roles as well.

Jan 1, 2012

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By Steve Kral

When the price of gold cracked the US$9.60/g(US$300/oz) mark last year, the gold-mining industry began to crank up again. This followed several years of gold prices that had languished in the mid-200s. Existing mines increased production and mines that had lain dormant for many years were getting second looks. The United States still produces a large amount of gold. But not much of the new production is coming from that country. Instead, strict environmental regulations still have companies wary of trying to invest the millions needed to start a new mine or expand existing ones. And after years of studies and negotiations between legislators, environmental interests and the mining industry, the United States still has not crafted a new mining law.

Jan 1, 2003

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

By G. P. Salas

I.- In order to keep pace feeding its fast growing population, Mexico with only about 20% of its surface suitable for intensive agriculture, will need the application of modern foodgrowing techniques. To assure greater crop yields it will be necessary to apply more fertilizers than used at present (yearly average of 29 Kgs/hectare)** For its fertilizers production Mexico still depends mostly on imports of phosphate concentrates from Florida, U.S.A., Morocco and Spain. To reduce or eliminate this dependence on foreign providers, the Consejo de Recursos Minerales -a Federal Government exploration Institute- started in 1974 an exhaustive exploration program for phosphate deposits more amenable to commercial exploitation than the phosphatic limestones contained within the La Caja Formation of Upper Jurassic, found along the Sierra Madre Oriental. After studying literature on the origin and deposition of marine phosphate and visits to deposits in Florida, U.S.A., the Baja California peninsula was selected as most favorable for starting this program because of its geologic and sedimentary history and also for its geographic location, where the cold California and warm Counterequatorial currents meet. Exploration activities executed by FORNOS, S. A. (1956) led to the disco very of low grade phosphate (3 to 5% P2O5) in the recent beach sands along the Bahia de Magdalena (Fig. # 1). In his doctoral thesis Bruno D'Anglejan Chatillon (1965) reports the presence of nodular phosphate on the continental shelf, between Isla Margarita and the Vizcaino peninsula. He estimated reserves of up to 1.5 million tons. A Mexican-American marine exploration company attempted in 1966 the evaluation of this deposit with negative results.

Jan 1, 1978

By V. Arslan

The primary advantage of using oxalic acid is in the formation during leaching of soluble complexes that are both photo-chemically and microbiologically degradable. In this study, chemical leaching and bioleaching methods were used for quartz sand. Using the ANOVA-Yates test technique, the effects of solids rate, temperature and oxalic acid rate were investigated using chemical leaching experiments. Solids rate and temperature were effective parameters on the chemical leaching. After the tests, the removal of Fe2O3 increased to 97.02%. Finally, the iron content decreased from 0.315% Fe2O3 to 0.0094% Fe2O3 in the leached quartz sand. The effect of pulp density was investigated on the bioleaching experiments. The bioleaching of iron oxides by Aspergillus niger resulted in removal of 47.70% of the total iron in the quartz sand, and suggested that this strain has not a good ability to remove iron impurities from quartz sand in comparison with chemical leaching. The iron content decreased from 0.315% Fe2O3 to 0.164% Fe2O3 in the bioleached quartz sand.

Jan 1, 2009

Extending an organization?s knowledge base throughout the entire enterprise can improve operations. Until recently, though, field operations were often left out of the information loop, as extending high-bandwidth communications into harsh environments often proved impossible due to thermal extremes, physical hazards and caustic chemicals. However, advances in the design and manufacture of rugged fiberoptic cables have now enabled the successful installation of 10-gigabit transmission links to places such as mining operations. The experience of Consol Energy exemplifies how plant managers can successfully enlist ruggedized tight buffered cables to help carry the efficiency of ERP communications into even the most challenging work environments. ?As part of our ERP implementation, we extended our corporate network underground into our mines using fi beroptic cable,? said Tom Prokop, manager-site support for Consol Energy. ?We?ve actually had rooffalls bury the cable between rocks and still did not lose data communications. Our maintenance personnel are now able to access our ERP system while underground at locations that can be up to 32 km (20 miles) away from their desks or the warehouse. Access to the corporate network allows them to order parts, look at electronic schematics, access monitoring data, no matter where they are in the mine. With a few hundred workers below ground, this immediate access translates into a time-savings that adds up in a hurry.?

Jan 1, 2009

Several years ago, Hudco Industrial Products began experimenting with the idea of levitating a conveyor belt with a film of air, much like the puck on an air-hockey table. While conducting its research, the company found out that some Russian and Dutch companies attempted the concept during the 1970s. After studying those conveyors, Hudco determined that its design was better. The Hudco advanced air-supported conveyor consists of an air-tight plenum, or chamber, that runs the length of the belt. The topside of the plenum has a formed trough. It corresponds to the profile of conventional troughing rollers. Low-pressure air is provided to the sealed plenum from a low horsepower blower. This pressurized air is metered and released through the central portion of the trough and reacts against the underside of the belt. The differential pressure between the top and bottom surfaces creates the lift to support the loaded belt. Airtight covers are installed to seal the transported materials in the plenum trough.

Jan 1, 2002

By Brian Fulcher

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft 3/sec) of water into Southern California. The 13 km (8-mile) tunnelling project is well underway and consists of two, 5.8 m (19-ft) diameter TBM bores through extremely variable geological conditions. An extensive and essential pre-excavation drilling and grouting program was performed in all reaches of the Arrowhead Tunnels Project, located north of San Bernardino, CA. This program supported the advance of two hybrid hard rock TBMs though extremely challenging ground conditions under substantial ground cover and up to 27 bar (900 ft) of ground water pressure. The well known San Andreas Fault lies nearby and has greatly influenced the local geological conditions. This paper will describe the means, methods and materials used throughout the numerous phases of the pre-excavation grouting program. It will also describe many versatile, flexible and innovative drilling and grouting methods and equipment systems utilized to improve performance, save time and costs in constantly changing geological conditions. Considerable lessons learned have been learned while overcoming some extremely formidable ground conditions and safely advancing the tunnels.

Jan 1, 2008

By S. Cotten

The regulations for current coal mine refuge alternative (RAs) require that there be sufficient life support to sustain survival of the maximum number of RA occupants for a minimum of 96 hours. This minimum duration assumes that rescuers can access the RA through the mine within four (4) days of the onset of the mine emergency. But what if mine rescue teams cannot reach the miners within the RA before the RA air supply is severely limited or exhausted? What could be done to extend the duration of the RA life support capability into the 97th hour and beyond? In addition, what might be done to enable more rapid rescue of the miners if they could not be reached through the mine in a timely manner? This paper describes a systems approach to address the potential need to extend the duration of RA life support beyond current design limits. New capabilities that need to be developed in advance of such a dire need include more reliable emergency communications, highly mobile and efficient drilling rigs, enhanced directional drilling techniques, and a standardized RA external life support interface along with RA internal design modifications to accommodate use of an external supply. The following sections describe the need, intent, and technology gaps associated with each of these capabilities. Government agencies and the mining industry should consider initiation of a program to investigate, design, and develop effective means of extending the current 96-hour time restriction on coal mine refuge alternative life support. The development process should begin with a focused study to refine the overall operational concept, investigate the current state-of-the art of critical technologies, identify specific technology development priorities, and make recommendations for a development program to provide in an organized, efficient, and timely manner a solution for extended refuge alternative life support and occupant rescue.

Jan 1, 2011

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007

By Anthony B. Szwilski, Dalip Sarin, Richard D. Begley

This paper will present the results of an analysis of several abandoned coal mine projects and includes field data for over a dozen different reclamation projects recently completed in the state of West Virginia. The analysis was performed with the objective of summarizing and or classification of the environmental consequences with reference to the characteristics of the mining facilities (surface, underground, etc.). The analysis also addressed the itemized cost of remediation with respect to procedures, environmental concerns and time. The results of the analysis are that each abandoned coal mine site in West Virginia have/had many unique features and in most cases include a combination of environmental concerns that complicate comparisons. The study also revealed that the abandoned mine land program for mines abandoned prior to 1977, that is being financed by a tax on the production of coal, has produced many benefits for the state of West Virginia. This grant program administered by the Office of Surface Mining, has resulted in a high quality methodology of remediation that has been successful for many years in greatly minimizing and/or eliminating environmental concerns from abandoned coal mines.

Feb 24, 1997

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 13, 2008 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. This will be the 21st Annual National Mining Museum and Induction Banquet. The four inductees are Lew Eklund, 76, Carrie Jane Billings Everson (1843-1914), ?Colonel? William C. Greene (1851-1911) and Arthur L. Hawkesworth (1860-1905). Lew Eklund founded Eklund Drilling that is now based in Elko, NV. He invented many designs that play a major role in today?s mining industry. His Cyclo Blower and various sampling devices he designed helped to revolutionize gold deposit exploration by allowing mining companies to effectively sample microscopic gold. Carrie Jane Billings Everson discovered and proved a method for bulk oil flotation concentration of mineral ores, the precursor to modern froth flotation methods of minerals concentration. She patented her process in 1886. In the early 1890s, coworkers built and operated demonstration plants incorporating her bulk oil flotation process. ?Colonel? William C. Greene was responsible for the development of the great copper mining properties of Cananea, Mexico. In seven years, he went from ragged cattleman and adventurer to the greatest captain of industry the borderlands have ever seen. Arthur L. Hawkesworth was a master mechanic for Anaconda Copper. He invented the detachable drill bit. His invention generated tremendous savings for the mining industry in time, in dollars and in safer operating conditions underground. His bit?s long lasting contribution to improved mine economics is immeasurable. The 21st Annual National Mining Museum and Induction Banquet will begin with an open house and reception at 5:30 p.m. followed by the dinner and program at 7 p.m. The inductions will bring to 201 the number of mining ?greats? whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2008