Search Documents

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By David Mast, Irwan Halim, Seung Han Kim

Fermilab is constructing a large underground cavern in Limestone to house scientific equipment. The cavern will have a complex L-shaped geometry and about 215-foot depth with relatively shallow rock cover, with service/egress shafts accesses into the cavern. Three-dimensional analytical models were developed to study the ground behavior and support performance. Multiple rock constitutive and failure models were evaluated. The models were significantly impacted by the high lateral in-situ earth pressure at the site. This paper will describe the design approaches that were taken to optimize the cavern arch geometry to allow safe construction in shallow rock, and permanent support requirements.

Jun 13, 2021

By P. A. Lindberg

Early Proterozoic ore deposits in the Verde district at Jerome, Arizona have produced 33.7 million metric tons of ore (1893-1975). The United Verde and United Verde Extension deposits produced most of the ore that yielded 1,644,323,100 kg Cu plus large amounts of Au, Ag, and Zn. These deposits are situated on the fractured and hydrothermally altered apex of a large submarine rhyolitic extrusive (Cleopatra formation). Precambrian lithologies are penetratively deformed and at Jerome the Fl folds plunge steep to the NNW. For the past two decades the volcanogenic model has superseded the replacement theory of ore formation.

Jan 1, 1992

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

By G. S. Dobby

Particle collection is considered to occur by particle collision with the bubble followed by the particle sliding over the bubble during which attachment may occur. Collision is quantified by a collision efficiency, EC. The existing model for EC is extended by including particle inertia. Attachment is quantified by an attachment efficiency, EA calculated as the fraction of particles which reside on the bubble for a time greater than the induction time. These calculations use recent data on the liquid velocity distribution over the upper half of rigid spheres. Collection efficiency, EK is given by EK = EC ? EA. Detachment is not considered. The mode is examined and shown to agree with much experimental data. For example the maximum observed in recovery vs particle size (d) can be explained as E increases with increasing d , while EA decreases. The decrease in selectivity at fine sizes is in accord with the model result that for dp < 5µm, EA ? 100% (i.e. EK ? EC) almost regardless of induction time. A decrease in bubble size does increase EK but does not improve selectivity. A high particle density (> 5g/cm3) is shown to cause a sharp peak in recovery vs size and a decreased maximum size of floatability. Finally, the possible effects of bubble and particle concentration are explored.

Jan 1, 1985

By David Mast, Irwan Halim, Brian Hagan, Kaveh Talebi, Jason Edberg, Amanda Foote

On June 14, 2023 Jay Dee Contractors’ Tunnel Boring Machine (TBM) “Phoenix” holed through and completed mining the second drive of the I-75 Segment 3 Storage and Drainage Tunnel. Completion of the tunnel came only after overcoming several challenges, including a groundwater intrusion event which deposited thousands of cubic yards of wet ground material into the tunnel. This paper will discuss the events which delayed completion of the tunnel by over nine months, the risk management and construction approaches assumed by the Design-Build team during bid, several challenges faced by Design-Build teams when building stormwater resilience tunnels using traditional Department of Transportation standards, and recommendations for improving risk allocation and proposal documents for future similar Design-Build tunnel projects.

Jun 23, 2024

By K. Neumann

"INTRODUCTION For many automation and safety tasks in open cut and underground scenarios it is crucial to have highly reliable distance measurements at hand. These measurements can for instance be used to obtain the exact position of a machine in one-, two- or even three dimensions. Research and development has shown interest in the ultra-wide-band technology (UWB) in recent years. While for this technology short range, high speed data transfer is the current main research focus, the technology can also be used for highly accurate ranging applications. Due to the use of a very wide frequency band, it is robust against disturbances of many types (e.g. EMC, rain, dust etc.) and is therefore attractive for the use in mining applications. The wide frequency band also offers benefits for ranging applications. Especially in environments with strong multipath problems such as in underground mines it is possible to focus on the dominant signal propagation path, thus increasing the reliability of the measurements. [1] State-of-the-art UWB ranging equipment claims precision within the range of a couple of centimeters and working ranges of more than hundred meters. At the Institute for Mining and Metallurgical Machinery (IMR) at RWTH Aachen University in Germany a modern UWB system was examined in several laboratory and real life tests to examine the feasibility of UWB bases ranging equipment in mining applications. UWB TECHNOLOGY The term ultra-wide-band denotes radio systems that use an ultra-wide frequency band. A common definition for UWB radio systems is that it needs to work on a frequency bandwidth of more than 500 MHz or a bandwidth equal to 20% or more of the center frequency [1]. Due to the ultra-wide frequency bandwidth UWB systems overlap the frequency spectrum of narrow band radio technologies like Wi-Fi, Bluetooth and other mobile communication systems which use a defined carrier frequency onto which information is modulated on (e.g. by using frequency or phase modulation). In order to not conflict with these other radio applications, it needs to be ascertained that the transmission power of a UWB system on a given frequency is so low that narrow band systems are not affected by it. As opposed to this only a small fraction of the UWB system’s bandwidth is affected by the narrow band system. The unaffected remaining bandwidth is sufficient to reconstruct the original signal, even if additional noise is present. Figure 1 shows the power spectral densities of popular radio standards [6], [7], [8]. A significant driver of research and development of UWB systems has been wireless high bandwidth communication. Using an ultra-wide frequency band is highly desirable here, as the channel capacity is dependent on the bandwidth. So far systems have been realized especially for short distances (e.g. wireless USB or Wireless HDMI) but beyond that, communication systems for long distances (several kilometers) are possible [2]. Advances in semiconductor technology led to a reduction in power dissipation of such systems. This enabled higher integration levels which in turn facilitated smaller solution sizes for space constrained applications [3]. Nowadays, UWB is also used for high-precision ranging applications [4], [5]."

Jan 1, 2015

By Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comninution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville&apos;s 5.5 x 6.4 m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790 to 1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By John A. L. Campbell

Although there has been an increased interest in the electrokinetic properties of coal (1) research on the subject is still in an early stage of development (2,3,4,5,6,7) To the author&apos;s knowledge, no electrokinetic studies have been made on coal lithotypes - particularly anthracite lithotypes. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods, It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published (8). The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results, however, the results are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation.

Jan 1, 1969

By A. G. Journel

Accurate prediction of recoverable reserves are key to the development and planning of a mining operation. Recovery functions for tonnage, quantity of metal and ore grade are defined and two approaches for their estimation are proposed. The indicator kriging (IK) approach draws on the data rank orders, whereas the multi-gaussian (MG) approach relies on a grade multi-variate distribution hypothesis. Although based on different premises, both approaches yield remarkably similar--and accurate--estimates for recoverable reserves.

Jan 1, 1984

By S. S. Peng

Hydraulic powered supports have been employed in the U. S. longwall mining for the last two&apos; decades. Yet the sciences of roof control at the powered supported faces remain largely unknown. Many questions remain unanswered. To address the problems, field investigations were conducted from 1980 to 1984 in seven longwall faces (1-10)(Table 1). Some of the findings have been reported by Peng and Chiang (11). The basic geological conditions of these panels are listed in Table 2. The mining equipment used in these longwall panels are listed in Table 3. Instrumentation and Observation Programs Two events were generally instrumented: one was the hydraulic leg pressures of the powered supports, and the other was the canopy and base plate load distributions.

Jan 1, 1986

By Y. Akin

The floatability of a typical boron mineral, colemanite (Ca2B6O11.5H2O), is shown to be hindered by the presence of montmorillonite type clay minerals. The clay is found to act in the form of slime coating. The mechanism of slime coating is investigated using pure colemanite and clay and their mixtures with an anionic reagent in a microflotation cell. Adsorption, flotation, solubility, zeta potential and scanning electron microscope studies reveal that slime coating occurs through electrostatic attraction. It is possible to minimize the effect of slime coating either at high surfactant concentration or at high pH values.

Jan 1, 1997

By Charles E. Dunne

One of the most frequently asked quesitons is: "Where is copper (price and usage) going?" I will not attempt to forecast either the future price of copper or the future growth of the copper industry; rather I would like to discuss the current trends experienced in the smelting and refining terms and conditions for sales and/or purchases of copper concentrates. A brief review of contract language and terms, together with a review of the common jargon, I believe, would be helpful. To accomplish this review, I will first list what I consider the four basic parts or sections of a basic ore contract and then illustrate basic terms with calculations.

Jan 1, 1984

By Charles Kimbell, L. Nahai, E. Shekarchi

INTRODUCTION AND SUMMARY World mineral trade during 1960 to 1984 has shown substantial changes both in value and tonnage. Although fuel commodities dominated total mineral trade during this period, this paper will focus attention primarily on nonfuel minerals. Brazil and Australia, modest producers of iron ore in 1960, have become dominant producers and exporters, together accounting for about half of major iron ore exports in 1984, far surpassing traditional export suppliers such as Sweden. Australia has also become the largest producer and trader of bauxite and alumina, and worldwide alumina trade has increased at the expense of bauxite trade. Similarly, shipments of ferroalloys have increased more than shipments of ores such as those of chromium and manganese. Canada, retaining its first rank in world export of zinc, has become also the leading source of potash and sulfur in world trade, and South Africa has been the dominant factor in chromite, manganese and their respective ferroalloys. Developing countries&apos; share of world copper trade has increased, with Chile maintaining first rank, but developed industrialized countries have continued to dominate production and trade of lead and zinc. Phosphate, sulfur, and potash have been the principal crude nonmetallic minerals traded worldwide. Looking to the near future, dramatic increases in export of iron ore, phosphate, potash and sulfur are not envisaged. Bauxite exports will continue to decline relative to alumina but at a slower rate than in the recent past. Zinc concentrate will continue to be exported but lead will be traded more as metal than as concentrate. For iron and steel, there will be some production shift from traditional producers to certain developing countries and recently industrializing developing countries such as Brazil, India, the Republic of Korea, and Taiwan. In the following sections dealing with specific commodities, it should be understood that information is presented only on the major forms of each commodity that move in trade, and only for a selected group of countries for each commodity or major form of each commodity. Thus, totals shown or mentioned generally represent only the totals of figures presented here and do not include estimates for minor forms of material or for countries that are not listed. However, the data provided is regarded as sufficiently complete to reflect major patterns and trends, and exclusions are there- fore not seen as affecting conclusions that may be drawn from the material provided. FUEL AND NONFUEL TRADE Values of Fuel and Nonfuel Trade The value of world export trade in major mineral commodities (ores, concentrates and scrap, crude minerals, iron and steel, nonferrous metals, nonmetallic minerals and mineral fuels) in 1983, the latest year for which comprehensive data are available, was reported by the United Nations in May 1985 to have totaled over 514 billion current U.S. dollars (Table 1). This was 79% of the historic record high of nearly $649 billion ,current dollars set in 1980, but almost 18 times the current dollar value reported for 1960. [1/] The value of these 1983 exports in constant 1960 dollars was $164 billion (Table 2), only 66% of the record 1980 high of almost $250 billion, and only about 5.7 times the 1960 dollar level.

Jan 1, 1986

By D. C. Yang

A packed column jig has been developed for sharp separation of fine particles--150 down to 1 micron--having different densities. The packed jig is a column filled with corrugated packing. A slurry of mixed particles is fed into the middle of the column. Water enters near the bottom of the column as both a steady state and a pulsating flow. The pulsating water sets up a jigging action that interacts with the packing causing the dense particles to sink and exit the bottom of the jig and the lighter particles to rise and exit the top of the packed jig. The result is a sharp, environmentally friendly, gravity separation machine with low operating costs. Grades and recoveries of iron ore exceed that of known devices. Grades as high as 95 percent purity with concomitantly high recoveries are common for iron ore concentration. Low silica, sulfur and phosphate are common. This paper is the first to unveil the packed column jig technology in detail and presents its physical model with performance data. The purification of iron ores and coal is the paper&apos;s focus.

Jan 1, 1997

By T. O. Kuhl

The Royal-Mountain King Project is 7.2 kilometers (4.5 miles) northwest of Copperopolis, California. Reserves of 8,250,000 t (9,100,000 st) at 2.32 g/t (0.068 oz/st) gold will be processed at 2500 t/d (2750 st/d) from three pits. Production is scheduled to begin the first quarter of 1989. District geology consists of northwest trending sequences of Jurassic meta-sedimentary and meta-volcanic rocks. Three ore bodies are located along the Hodson fault which trends northwest and dips 40 degrees northeast. The Gold Knoll and North Pit ore bodies are hosted in carbonate and silica altered meta-volcanic rocks whereas the Skyrocket ore body is hosted in quartz stockwork zones in meta-sedimentary rocks. Gold is present as inclusions and micro-veinlets in pyrite.

Jan 1, 1989

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive&apos;s velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By O. J. C. Runnalls

Canada has played a significant role in the international uranium industry for some three decades. Although there have been many challenges in the past, the future offers a more extensive range of problems and prospects as Canada moves to expand its activities in all aspects of the nuclear fuel cycle. World uranium demand could grow to an annual requirement of 500,000 tons U308 by the year 2000. A substantial fraction of this material is likely to come from Canada because the country&apos;s reserves and resources are large, and because of a favourable geological potential for future discoveries. There has been a long history of association between the producing industry and the federal government, and it has provided the foundation for existing national uranium policies. Close industry-government association will be maintained and developed in future because of the anticipated rapid growth of the industry and the consequent need for continual refinement of government policies relating to exploration, mining, processing and export of uranium.

Jan 1, 1975

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

High pressure roll grinding (HPGR) is a mature but still expanding comminution technology. In the metals mining industry, HPGR is slowly gaining acceptance as a cost-efficient, high-throughput alternative for plant optimization. The increasing need to treat ores with progressively lower grades, complex mineralogies, refractory metal occurrence and variable rock types requires an energy-efficient comminution technology that reduces metallurgical problems inherent in conventional crushing and grinding, while stabilizing leach and flotation circuits and increasing metals extraction. This paper will summarize our latest HPGR pilot test results for gold and copper projects in the United States and South America and their confirmation through the first HPGR operation in copper mining. This paper will also stress the use of the high pressure grinding roll as a metallurgical tool. The application of HPGR for the treatment of heap leach SX-EW ores, semi-refractory gold ores, waste rock material and concentrator feeds will be illustrated.

Jan 1, 1998