Search Documents

By Joseph Matoney, B. K. Parekh

INTRODUCTION The term "dewatering" refers to removal of water from coal. Water associated with coal can be categorized as "free or surface" and "inherent or chemically bound" moisture.' The free moisture is found on the surface of coal, in capillaries and small spaces between two or more particles. The inherent or chemically bound water is found in the interior of the coal and as part of coal structure. A significant amount of free moisture can be removed by mechanical dewatering techniques. However, inherent moisture can only be removed by applying energy intensive techniques, e.g., direct or indirect heating. Moisture in the coal offsets some of the benefits of coal cleaning. Extra water in clean coal adds to extra cost in transportation, heat lost during vaporization, and plugging of chutes. From a utility perspective, a 1 % increase in moisture can offset a 4.5% decrease in ash.2 Mechanical dewatering can be classified into two major process categories according to the principles involved, namely, 1. Sedimentation-liquid is constrained and particles move freely. 2. Filtration-particles are constrained by a medium and the liquid flows through. Each of the process categories is composed of various separation techniques shown in Fig. Equipment currently being used by the mechanical dewatering of coal of varying size ranges and final moisture content is illustrated in Fig. 8-2. This figure indicates that sizes larger than 13/, in. (37.5 mm) present no particular dewatering problem. Shaker screens of the very crudest types and designs are capable of producing these sizes at low surface moistures. High-speed vibrators are used for the intermediate sizes and can be used for smaller sizes down to 0.02 in. (0.5 mm) if high moistures (15% surface moisture or greater) can be tolerated in the product. Usually, however, the vibrator is not used below 3/, to 3/, in. (9.5 to 6.3 mm) because of the moisture associated with these fine sizes. At this level, centrifugal force is usually employed to aid dewatering. Centrifuges of various types and designs are used practically

Jan 1, 1991

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By N. S. Tanious

This work was completed prior to the author's appointment with the Nuclear Regulatory Commission (NRC). Therefore the views and conclusions contained in this paper are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the NRC. Reference to specific brands, instruments, or trade names is made to facilitate understanding and does not imply endorsement by the author or the NRC.

Jan 1, 1987

By E. Fidler

A recent headline in the Wall Street Journal declared, "trendy management schemes very often fail." Many of the management techniques addressed in the accompanying article are associated with quality management including reengineering, benchmarking, total quality management, and employee empowerment. The article made the point that executives, employees, and customers who are involved in such programs rate the effectiveness of these programs very low, and the programs often fail. Yet, we all know of companies that have made significant advances in their operations using these same quality management practices. Why do a few succeed while many fail? History has shown that the companies that successfully carry out quality management programs have two things in common: 1) Strong leadership committed to the success of the program. 2) A comprehensive plan for carrying out and maintaining the program. Stated another way -the reason many companies fail is the lack of committed leaders and inadequate planning. It is ironic that the title of the Wall Street Journal article is "The Best Laid Plans."

Jan 1, 1994

Flotation of dolomite from apatite was investigated, using dodecylamine hydrochloride or sodium oleate as the collector, in the absence and presence of inorganic modifiers such as sodium chloride. Separation of dolomite from apatite was anticipated from the single mineral experiments under various pH and collector concentration conditions. Flotation selectivity in the mixtures, however, was found to be limited. Attempts to control the flotation response of these minerals by addition of salts such as NaCI and KCI indicated that selectivity is possible. The presence of sodium chloride was determined to depress apatite flotation using sodium oleate leaving dolomite flotation unaffected (Moudgil and Ince, 1989). In this paper, conditions for optimum separation and the effect of major parameters on the desired selectivity are discussed.

Jan 1, 1990

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By J. J. Lewis

In the mid-1970's a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979

By Robert K. Jones

Filter media can be defined as that material which effects the removal of finely divided solids from a fluid. Thus the removal of dust from air or turbidity from water, for example, can be the result of passing the fluid through a properly supported filter media. Since filtration in one form or another has been practiced since pre¬historic times filter media have been made from an extremely wide variety of materials. Vegetable and synthetic fibers (used loose, or formed into papers, felts or cloth) sand, ground coal, diatomite, perlite, wire cloth, porous metal, and bonded aluminum oxide are among the more important materials used today.

Jan 1, 1961

The future phosphate rock deposits in South Florida contain a significant fraction of dolomite. The high MgO content of the rock is undesirable in the production of phosphoric acid. Several flotation schemes have been attempted to separate dolomite from phosphate rock. Alternately, Selective Flocculation process has been suggested to separate dolomite from apatite. A high MgO content rock was simulated by a 30:10:60 synthetic mixture of apatite, dolomite and silica. Single mineral selectivity was observed in the mixed mineral systems apatite-silica and dolomite-silica with Polyacrylic acid (PM) and Poly(ethylene oxide) (PEO) flocculants respectively but not realized in apatite-dolomite system with PEO flocculant. Heteroflocculation, suspected to be the major reason for loss in selectivity, was minimized by addition of a Site Blocking Agent (lower molecular weight fraction of PEO). Process parameters such as size reduction schemes, flocculant/SBA dosage, and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed mineral tests was translated into the ternary mixed mineral system, viz. apatite-dolomite-silica. In this presentation surface chemical characterization of the samples and their flocculation behavior will be discussed.

Jan 1, 1994

By M. Guzman, S. B. Thais, M. F. Obispo, M. R. Arribasplata

The impact generated by old abandoned mines in Peru have produced mining environmental liabilities, which can generate an impact on the environment. In the search for long-term sustainable solutions, Phytoremediation is presented as an interesting alternative, since it allows the use of Peruvian native plant species for the accumulation of heavy metals. In this paper, we present the results of native high Andean species: Stipa Ichu and Cortaderia Nitida. The final metal concentration in the aerial parts and in the roots of each plant show that Stipa Ichu is more efficient to recover Fe, reaching almost 278 times its initial value. In the same way, this plant is efficient to remove Zn, Cu and Cd, reaching maximum values of 64, 39 and 12 times its initial concentration respectively. Cortaderia Nitida turned out to be more efficient to recover Fe, Zn, Cu and Cr, with highest recovery of 250, 117, 39 and 13 times its initial value respectively. Finally, based on translocation factor, Stipa Ichu has better capacities of hyperaccumulation of Fe, Cu, Zn, Pb and Cr. Cortaderia Nitida only shows hyperaccumulation of Cr.

Mar 2, 2022

By Lauren W. Choate

Wollastonite, a calcium metasilicate, derives its name from the man who discovered the mineral, Doctor William H. Wollaston, an English scientist. OCCURENCE Occurences of the mineral have been noted in Finland, Switzerland, Russia, Japan, Mexico and in the United States in Texas, California, Arizona, and New York. The only commercial deposit now being exploited is at Willsboro, New York. It is mined and processed by the Cabot Corporation whose home offices are in Boston, Massachusetts.

Jan 1, 1964

By Mark E. Emerson

Foreign and domestic companies find the mineral potential of this country's stern public lands, its capital markets, political stability, and "open-door" policy attractive for hard mineral exploration. Traditionally, exploration in the US has been geographically based and responsibility oriented at the district level. The 1970s brought a decentralized approach to exploration as major non-metal companies began to diversify into hard minerals. The emphasis was on capital intensive metal and energy projects involving bulk-tonnages. The recent economic downturn in metals has caused many of the new participants to withdraw from the mineral scene. The surviving companies have shifted their emphasis toward medium scale precious metal projects having high operating margins and rapid return on equity. Exploration expenditures in the United States are now principally focused on gold and silver to the exclusion of practically all other commodities. In the search for precious metals companies have scaled back their exploration efforts and have began to apply new approaches to target selection. The search is being assisted by rapidly evolving conceptual models. The change in orientation has led to numerous new discoveries. The finds are essentially "rediscoveries" that c,-re previously uneconomic. The majority are low-grade surface deposits that have involved low discovery costs and short lead times for development by low-cost mining and beneficiation methods. The emphasis on gold to the exclusion of all other commodities raises questions regarding the direction of exploration in the US for the rest of the 80s.

Jan 1, 1984

By Luc Morin

What you don't know won't hurt you! This attitude can get you into trouble when considering your process! When trying to extract the most and the best possible performance from a mineral processing circuit this should be reworded to say: What you don't know about your process will hurt your profits! Today, with the popularity of joint ventures, custom milling contracts and process audits by specialists, not knowing is a formula for trouble! Good Sampling Systems are no longer considered a luxury' Not too long ago the practice of grab sampling was considered acceptable and became the norm. Today, it is rare to hear metallurgists say, "All I need is a trend not a good representative sample. so I'll just grab a sample every few hours." Buyers and sellers of quality products have found that grab sampling leads to poor partnerships'

Jan 1, 1999

By F. W. Brackebusch

A unique machine has been designed for mining narrow veins. The machine, called the NONN, walks on the walls of the stope and carries a boom-mounted hydraulic impact breaker. The concept of walking on the walls allows an existing muck handling system such as LHDs to operate beneath the NOMN. The NOMM has four sets of legs which can be manipulated independently or concurrently to cause the carrier to walk in any direction and to turn sharp corners. The mining rate using the breasting method is targeted to be 25 t/hr.

Jan 1, 1990

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

By C. S. Davis

In being asked to present this paper on the improvements in loading and hauling equipment and the effect on unit costs, Mr. Van De Water, your program chairman, stated that his reason for coming to a contractor was due to the wide experience of, and I quote: "a large contracting firm using a variety of equipment on varying types of earth moving jobs." We people in Utah Construction Company are flattered that Mr. Van De Water singled out our Company for this assignment. Utah Construction Company's participation in open pit mine stripping antedates the 1920's, when overburden was being removed from copper ore in Bingham Canyon, Utah. Our first stripping con¬tract for the Copper Company was finished in 1912. Since that early beginning, Utah has, as a contractor, been engaged to strip and mine iron ore properties, coal properties, copper properties, uranium properties, phosphate,-gypsum, limestone and dolomite properties. And, as you know, the Company has become a major producer of iron ore from Company-owned open pit mines. Utah Construction Company has been instrumental in the evolution of open pit mining tools. Some of the first tools were the old wood and coal fired stream shovels which had to be fired hours before a shift started to insure a full head of steam, providing power to excavate with the then large 1-1/2 cubic yard buckets. Today, Utah's strip mining is done, with 18 cubic yard and 10 cubic yard crawler shovels. Yesterday's horse and mule drawn, iron wheeled wagons, with 1 and 2 cubic yard capacity, which were hand dumped by removing the false bottom, one 2 x 4 at a time, have been replaced by today's- 50-ton capacity, hydraulic, rear dump trucks and giant 40-ton coal haulers. Utah Construction Company used the early fresnes and wheeled scrapers which were horse and mule drawn. Often, an operator holding too tightly to a handle was thrown into his horses when a hard spot turned the scraper, a contrast with today's 20 and 25 cubic yard, self-powered diesel and diesel electric Gargantuan rigs; with power controls that relieve the operator of practically all physical work. This Company has pioneered many of today's advances in equipment with shop made prototypes, features of which were adopted and elaborated upon by equipment manufacturers.

Jan 1, 1959

By Robert W. Row

Advanced physical coal cleaning processes that are now under development may remove significantly greater fractions of pyritic sulfur and ash than do commercial coal cleaning processes at comparable heating value recoveries. These processes may be useful for reducing sulfur dioxide emissions from electric utilities and other emission sources. However, little work has been done to determine their applicability to any major coal market. The northeastern states of the United States are interested in burning more coal, but with further sulfur dioxide emission restrictions. Their nearest coal sources are relatively high sulfur Northern Appalachian coals. The project discussed in this paper, which is scheduled to be completed in June 1985, has the objective of technically and economically evaluating various coal supply scenarios involving five selected advanced physical coal cleaning processes; and comparing the economics of them with alternative fuel supply options open to the northeastern users.

Jan 1, 1985

By L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million ton'> of ash, boiler slag and FGD (flue gas desulfurization -"scrubber") materials as by-products. Utilities and others who burn coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Jan 1, 1997

By K. J. Hartman

The term kaolin is derived from "kauling". a Chinese word meaning high ridge, which was the name of a hill in China where kaolin was first mined several hundred years ago.(1) Other common names used today for kaolin include "clay" and "China Clay". The former word technically has a broader meaning and could refer to various types of clays such as bentonite and ball clay as well as kaolin. China clay, as a descriptive term, apparently results from kaolin's origin as described above but could also be due to a significant historical use in ceramic applications. The terms "kaolin" and "clay" will be used interchangeably in this analysis because of the common practice of using these terms in the paper industry. Major reasons for kaolin's widespread industrial usages center on the mineral's (kaolinite) physical features of good color, low viscosity and inertness. Kaolin is described as a hydrous aluminum silicate with approximate composition Of 2H20.A1203.2Si02. As will be shown later, a new version of the product, calcined clay with modified hydration content, is gaining widespread usages. Components of any particular kaolin in addition to alumina and silica are viewed as impurities. The more valued deposits and, hence, higher priced kaolin products are those of highest purity.

Jan 1, 1986