Search Documents

By P. Rusin

A new bacterium, Thiobacillus cuprinus, can extract copper from chalcopyrite as rapidly as T. ferrooxidans. On solution with and without nutrient amendments and bacterial growth media were supplemented with T. ferrooxidans or T. cuprinus in shake flask studies. Both species extracted -42% of the copper using growth media. In one case, T. cuprinus solubilized approximately twice as much copper as T. ferrooxidans utilizing a seeded On solution. Thiobacillus prosperus also oxidizes chalcopyrite and tolerates high chloride concentrations. These sulfide-oxidizing bacteria are representatives of the mixed microbial community found in sulfide dumps. Rates of biological copper extraction from sulfide ores, using the native microbes, have been significantly enhanced by amending On solution with PGM.

Jan 1, 1994

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015

By Donald P. Moore

During April 1967 a Frasch sulfur mine was placed in operation near Fort Stockton, Pecos County, in West Texas. This was the first Frasch mine to recover native sulfur from a deposit not associated with the caprock of a salt dome. Since 1967 two additional mines have been opened in west Texas, another one near the first at Fort Stockton and a third one near Orla in Culberson County (Figure 2). Recoverable reserves at the Culberson County mine are estimated to be 57,000,000 long tons of native sulfur (Zimmerman and Thomas, 1969). Total recoverable reserves at the three mines probably exceed 60,000,000 long tons, Studies of the geochemical cycle of native sulfur mineralization in test Texas indicate an origin similar to the deposits on salt domes although the geologic framework is different. A comparison of the geologic setting of the west Texas deposits with the deposits in the Union of Soviet Socialist Republics as reported in the literature, reveals many similarities. ACKNOWLEDGEMENTS The writer wishes to express his appreciation to Cities Service Minerals Corporation for support throughout this study. Special thanks are due Dr. Chris Riecken and Mr. Dave Hardy for their

Jan 1, 1971

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By G. A. Campbell

This paper considers the international market trends of the rare earths and how they are strongly influenced by the by-product/co-product nature of their mining and processing. The two main economic minerals for the rare earths are bastnasite and monazite. Monazite is primarily a by-product of mining ilmenite and rutile and is affected by changes in these markets as well as the presence of thorium. Bastnasite is a by-product of mining iron ore in China and a stand-alone product in the USA. The paper will use conceptional relationships and empirical data to delineate the various by-products/co-products relationships and how they determine observed international market behavior.

Jan 1, 1996

By A. B. Cecala

The Bureau of Mines has been performing research to lower the dust exposure of workers at mineral processing operations for a number of years. This research has mainly been directed at source control techniques in an effort to lower a worker's dust exposure at a particular job function. In some cases, this control technology provided a carryover effect in lowering the exposure of workers at other locations, but for the most part had very little effect in lowering dust levels throughout an entire mill building. Recently, the Bureau became aware of several mineral processing operations having problems with high over-all mill dust levels. These operations were all using baghouse-type collectors to address their most serious dust contamination areas. Although these major dust sources were being controlled, there were numerous minor dust sources that were not. These minor dust sources were causing dust levels in these operations to gradually increase as the day or shift progressed. The intent of this work was to determine general guidelines and design criteria for operations that may be interested in implementing a total mill ventilation system. Most mill buildings can be considered a closed system and thus any dust that is not being controlled within the structure, will cause dust levels to gradually increase over the shift. A total mill ventilation system should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust laden areas throughout the mill structure. This air should be discharged at or near the top of the structure, where it is not a contaminant to plant personnel working outside. Without this exhaust system, dust can exit the building through open doors, windows, etc., and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. A total mill ventilation system is not a stand-alone technique, but is a supplemental technique to assist other localized dust control systems.

Jan 1, 1994

By R. L. Grayson, R. C. Althouse, M. J. Klishis

The health and safety of employees, efficiency of the operating system, and production are paramount goals in underground coal mining. The section foreman assumes responsibility for making his part of the total system function to meet these goals. However, section foremen often have not been prepared to assume the full range of their responsibilities upon becoming a supervisor. This paper addresses the full range of section foreman responsibilities and concomitant authority. Management principles that must be mastered by him are presented, and performance expectations as well as criteria for their evaluation are examined. The benefits realized from effective foreman training are discussed.

Jan 1, 1987

By John F. Shea

When Dick Robbins asked me to give a keynote address, I felt it might be in order to review some of the practices and techniques used in tunneling and work up to some of the concepts now used to mine and construct tunnels. Needless to say, there have been many changes in tunneling technology and also many changes in the Safety Codes controling them. An example of this latter change was the fact that in 1931, my father excavated the Owyhee Tunnel No.5 with gas locomotives. He was able to do it because there was no natural gas in the rock and the ventilation system was designed to free the tunnel atmosphere from powder and exhaust fumes. Today OSHA rules would never permit gas locomotives underground, although there were no incidents on this particular project. One of my first tunnels, as Project Manager, was the Clear Creek Tunnel for the Bureau of Reclamation. Our method of handling muck was the Conway Muckers. This unit was a valuable improvement to the hand mucking of previous generations. The Conway was also used in our Navajo Project, in New Mexico. Unlike the Clear Creek project, where water was one of our main problems - up to 7,200 gallons per minute, at a pressure of 395 pounds per square inch - in the Navajo Tunnel, we had a mixed face which caused a major problem with our support system. In one of the Navajo Tunnels, there was a major cave-in, when the squeezing shale came in during an attempt to strengthen the support system. Although moving shale was not a constant problem, there were areas where the shale was five to six feet above the spring line.

Jan 1, 1976

By Koji Nakanishi, Masayoshi Karasawa, Yasuhiro Morimoto

"Shin-Yokohama station (tentative name), one of the station of the Sotetsu - Tokyu through line (ST line), is under construction by the OPEN – CUT method. The Underground Soil–Cement Steel Diaphragm Wall is implemented as an earth retaining wall. This earth retaining wall is utilized as a main body of a subway station. It is the first time to utilize this earth retaining wall as the main body. There are two difficult issues for this project. One is that this station is planned under busy major road and there are many underground utilities, for example, an electrical transmission line. Because of that, construction area is limited. The other is that this station is located in a thick soft clay layer. This layer has a high risk of consolidation settlement because of draining during main excavation. Thus, high water tightness is required for this earth retaining wall. This paper reports design and construction methods for the Underground Soil–Cement Steel Diaphragm wall introduced as a part of the body of the subway station.1. OUTLINE OF SHIN-YOKOHAMA STATION 1-1. Location and structure of Shin-Yokohama Station Shin-Yokohama station is an intermediate station on the ST line connected to the Tokaido-Shinkansen bullet train, the JR-Yokohama line and the Yokohama Municipal Subway. Access to Tokyo and the Tokaido- Shinkansen from the eastern part of Yokohama city will be improved by this project. In addition, the number of estimated passengers of this station is one hundred thousand people/day because a soccer stadium (Nissan Stadium: 72,000 people), a huge indoor arena and a hotel are located in this area. This station consists of 4 stories and 3 spans (Max width; 29m, Depth; 33m, Length; 325.5m). Completion image is shown in Figure 2. Generally, stations have 1 platform and 2 trucks. But this station has 2 platforms and 3 tracks because some of ST line trains return at this station and a train deadheads from Hazawa station to this station in an emergency. This station is planned as 4 stories underground station, and the platform is on the lowest story. The reason why this station is in such a deeper position is to prevent the alignment from interfering with the Yokohama Municipal Subway station and foundation piles for bridge piers existing along the alignment. Even under the constraint conditions, earth covering should be shallow as much as possible. As a result, the tunnel edge is very close to the foundation pile, and the gap is only about 2m (Figure 3). In addition, passengers will be able to change trains easily from the ST line to the Yokohama Municipal Subway or vice versa at this station."

Jan 1, 2016

By R. E. Blair

The economics of the producer-consumer interface - the route from mine to market - impact much more severely on specialty industrial minerals, extender/fillers that have to be sold, than on commodity industrial minerals that are basically supplied. Working capital costs for inventories and accounts receivable, fixed capital costs for storage/ warehousing/distribution, and sales and marketing costs all make the extender/filler producer much more of a marketer than a miner. The future survival of an extender/filler producer will primarily depend on the skill he has in the economics of the interface.

Jan 1, 1981

By X. Xie

The dissolution behavior of palladium powder in thiourea solutions has been studied. The variables studied included temperature, stirring speed, and concentrations of thiourea, acid and ferric ion. Palladium was found to be soluble in thiourea solutions in the presence of an oxidant such as ferric ion. The dissolution of palladium in thiourea solutions was found to be chemical reaction controlled with an apparent activation energy of about 2S.3 kJ/mol.

Jan 1, 1995

By S. Shankar

The phenomenon of re-entrainment is seen in many environments, such as sand dune formation, soil erosion, fugitive dust emission, spread of radio-nuclides from accidents involving nuclear weapons, etc. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of on-going research in the Respirable Dust Center on the prediction of ambient dust concentrations in mine atmospheres (Ramani, 1983) to identify the contribution of dust re-entrainment to the spatial and temporal concentration in mine airways and included wind tunnel and in-mine studies. A set of seven experiments was performed in the Lake Lynn Laboratory Mine of the U.S. Bureau of Mines under controlled conditions. Two types of source coal dust, anthracite and bituminous, were subjected to airflow with a range of air velocities and walking by two different walkers. Six sets of instruments were used along the test section for sampling the airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/s. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (i.e., total) airborne dust increased to 0.17 mg/m' (standard deviation = 0.10 mg/m') from an initial value of 0.02 mg/m'. The action of personnel walking, however, caused higher amounts of re-entrainment. Average concentration of respirable and total dust at the center of the mine airway increased to values of 0.28 mg/m' (standard deviation = 0.12 mg/m3) and 1.53 mg/m3 (standard deviation = 1.0 mg/m3), from initial values of 0.03 mg/m3 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal dust bed. Depending on the level of activity and the amount of dust deposited in mine airways, re-entrainment may become an important source of airborne dust away from the point of actual mining.

Jan 1, 1994

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By R. H. King

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. So far, we have developed and reported on algorithms that automatically produce accurate time-study reports of continuous miner data from kilowatt sensors at the Deserado Mine, and we are extending the system to accept other types of sensor data input. This paper focuses on AI techniques that improve accuracy of the numerical algorithms in the PRS module. Additional AI work for the KRS module is summarized in this paper.

Jan 1, 1989

By W. J. Wuest

The U.S. Bureau of Mines (USBM) has recently developed a rock mass classification system for evaluating the structural competency of bedded roof strata; the Coal Mine Roof Rating, or CMRR. When compiled with the companion Lotus 1-2-3 spreadsheet, which is simple to learn and use, CMRR data are a useful tool with applications to longwall gate road pillar design, safety hazard mapping, and artificial roof support analysis. This paper demonstrates these applications under actual conditions found in current U.S. mining operations.

Jan 1, 1995

By Earl M. Frizzell

This paper addresses considerations for the use of artificial support of pit walls in surface mines, a new project of the Bureau of Mines. Results to date indicate that a polymer-coated cable with embedded grit could provide good anchorage for stabilizing benches and highwalls, and an electronic method of recording discontinuities in the field is being reviewed and developed for application to mining. The objectives of the work in progress are to define the engineering parameters and evaluate the concepts for artificial supports in order to provide safe working environments when pit slopes are steepened to increase ore recovery and reduce overburden handling.

Jan 1, 1986

By Ed Ramsay

The Hill is a cyanidation plant with flotation and roasting. The grinding and treatment have at the present time a capacity of 1400 tons of ore per day and the precipitation has a capacity of 6000 tons per day. The ore is delivered by a 36" conveyor belt and tripper to 8 mill bins having a capacity of 6000 tons. The ore from these bins is discharged onto 20" gathering conveyor belts which are regulated with p.i.v. speed changers to control the belt weight. A weightometer determines the tonnage milled. The feed enters the 8' x 12' rod mill through a rubber lined chute and the product is discharged through a launder to a 7' rake classifier in closed circuit with 10' by 6' hardinge ball mill. Lime slurry is added at the rake classifier to give a strength of .30#/ton. The classifier sand is fed into the ball mill with a scoop feeder and the mill discharge flows in a launder back to the classifier. The classifier overflow is pumped to a 24' by 12' bowl classifier in closed circuit with a 8' by 15' regrind mill. The bowl classifier sands are fed to this mill and the mill discharge is pumped back to the bowl. The bowl overflow at 8% - 200 mesh is the final product from the grinding circuit.

Jan 1, 1975

By E. Watkins, S. J. Schatzel, V. Gangrade, K. M. Ajayi, Z. Khademian

Longwall-induced deformations could jeopardize the mechanical integrity of shale gas well casings positioned in the abutment pillar of a longwall mine. The in situ and induced fracture networks surrounding the gas well could provide pathways for gas flow into the mine creating safety concerns. Hence, this study by the National Institute for Occupational Safety and Health (NIOSH) develops a discrete fracture network (DFN) model to characterize the fractures in the overburden based on geomechanical analyses of mining-induced fracture apertures at a study site in southwestern Pennsylvania. The apertures from the geomechanical model are used to develop a stochastic DFN model of the site in fracture flow code (FFC). Multiple realizations of the stochastic DFN model that replicate potential fracture geometries are simulated, and the fracture permeability is compared with field measurements. A maximum field measurement of 5.03 × 10− 12 m2 (5080 mD) and 3.82 × 10− 13 m2 (386 mD) was estimated over the abutment pillar at the Sewickley and Uniontown horizon, respectively. The results show that the average permeabilities from the DFN model agree closely with the field measurements. In addition, the comparison of all the field measurements and 100 DFN realizations show the model is representative of field conditions. These findings provide critical information regarding fracture characteristics in the overburden, which will further be used to predict potential shale gas flow to the mine in the event of a casing breach for an unconventional gas well.

Jun 17, 2022

By Jonq-Keh Lee

This paper deals with the effects of air leakage from intake to return airways through a series of stoppings on the analysis of coal mine ventilation. The mathematical model which assumes continuous leakage along adjoining intake and return airways is reviewed, and a new mathematical approach is presented based upon the concentrated leakage through individual stoppings. The procedure incorporating the new method in the analysis of coal mine ventilation networks is also discussed.

Jan 1, 1984

By Jacques B. Wertz

Although fracture intersections and "domes" seem at a number of places to be the basic structural combination for the occurrence of a mining district, of the porphyry-copper type particularly, this situation is, of course, not always to be expected. For instance, the group of mines comprising Superior, Ray, Miami, Globe, Christmas appeared from the beginning of these structural studies as typical exceptions, and there are others. One had to expect additional parameters to allow for any mineral concentration to occur. One of these apparent parameters is here considered. From the result of stratigraphic studies related to ancient formations in Southeast Arizona, the Martin limestone (Devonian in age) was retained as having a possible relationship with the structure-economic studies in progress, as evidenced for instance by the mineralized O'Carroll bed located at the base of the Martin. This limestone formation has been rather extensively investigated in the past and there are many known sample localities. For this work, the isopach map was drawn by computer to insure more objectivity and, in addition to the available data points, a number of dummy points with a zero value were added around the assumed form-

Jan 1, 1971