Search Documents

By E. Tarshizi

This research project demonstrates the application of a mine system simulation and animation model in enhancing the efficiency of a truck-shovel operation and reducing the haulage environmental impact in an open-cut coal mine. In any mine, a key objective is to have enough equipment for production and not have excess to where it is counterproductive. Due to the advent of responsible mining, environmental regulations, and eco-friendly practices, these factors must also be considered in the analysis. The over-trucked situation at a mine will be discussed, i.e. when the number of trucks exceeds the optimum number of trucks a mine should have for the most productive/profitable mining operation. When the system has an excess number of trucks, truck utilization is reduced which impacts mine operation, capital costs and the environment, through unnecessary truck purchase, energy use, air pollution etc. A hypothetical surface coal mine layout was used for the simulation model.

Feb 23, 2014

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez, Nishan Pokhrel, Lizeth Jaramillo

This paper presents a case study of respirable dust characterization in a thin-seam coal mine in southern West Virginia. Samples were collected in various locations within the mine and analyzed using scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), thermogravimetric analysis (TGA), and Fourier transform-infrared (FT-IR) spectroscopy. The study found high non-carbonate mineral content, particularly aluminosilicates and silica, in the dust. The results indicate that fine aluminosilicate particles may interfere with SEM-EDX analysis, leading to an underestimation of coal content. The findings highlight the importance of using multiple analytical methods to accurately characterize respirable coal mine dust.

May 5, 2022

By W. H. W. Husband

Rock salt has been mined by the solution method for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the' same method. However, only Kalium Chemicals Limited (1) has been successful, possibly because the conditions in Saskatchewan are the most favorable conditions to be found so far for the development of a solution mining method for potash. There are significant differences in solution mining of rock salt and solution mining of potash. First, rock salt deposits are relatively pure in respect to soluble minerals, whereas potash is never found in the pure state and contains Substantial amounts of other soluble minerals, particularly rock salt. In comparison to rock salt, much less potash is dissolved and brought to the surface for the same amount of water circulated through the orebody. The amount of water to be evaporated per unit weight of product is a major difference. Much greater amounts of water must be evaporated when producing potash and the treatment of the brine is more complicated because other dissolved salts have to be separated. Secondly, the rock salt deposits, particularly the domes, are much thicker. Bed thickness is of prime importance because it determines the yield of a well and consequently the economics of the process. Furthermore, as rock salt provides a strong roof structure, larger cavities can be developed and this prolongs the life of the rock salt well.

Jan 1, 1971

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By Keith A. Heasley

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence. Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents several case studies where a mechanics-based, boundary-element program is used to back-calculate the surface subsidence associated with various panels at several Northern Appalachian coal mines. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin scam or vein type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from the case studies in this paper demonstrate that the laminated model with calibrated properties can easily provide moderately accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies arc recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

Jan 1, 1999

By Andrzej Wala, Tom Altman, Tom Hughes

The University of Kentucky Mine Ventilation Manager (UKMVM) is a system that contains Level Five knowledge bases and comprises an expert mine ventilation management system. The package uses production rule language (PRL) to interpret data monitored from sensors, e.g., for airflow, temperature, and concentration of gases, in an underground mining environment. Activated from the PRL knowledge bases are Pascal subprograms which (1) organize the monitored data to set up emergency consultations, (2) display graphic representations of a mine's ventilation network with the latest sensor readings, (3) provide interactive updating of mine ventilation parameters, e.g., resistance changes, revised flow requirements, and new regulator and fan settings. Also activated from these knowledge bases are programs which (1) monitor airflow, temperature and gas concentrations from a physical mine ventilation model and (2) adjust regulator openings and fan rpm's. Thus, as an expert system the UKMVM not only presents advisory consultations for underground environmental emergencies, but also serves as an interface between the monitoring and responsive control aspects in the continuous maintenance of normal mine ventilation.

Jan 1, 1989

By Manchao He, Xiaoding Xu, Yubing Gao

Based on the geological conditions of the 15,600 working face in Pingba Mine, this paper establishes the mechanical model of the stress distribution in the pre-working face under the influence of mining pressure based on a hemispherical stress distribution theory. The analytical formula for the stress distribution is determined. A numerical model for the mining pressure under the influence of key layer is also constructed, and dynamic stress interruptions under various roof-cutting relief schemes in different horizontal positions are simulated. The stress distribution of the stope under different pressure relief schemes is analyzed and compared with the theoretical results. Results show that blasting roof cutting blocks the transmission of the abutment pressure to the working surface to the coal and rock mass in front of the working face, reducing the significant working face mining pressure influence range, which decreases as blasting pressure relief position moves toward the working face. Stress accumulation in the coal in front of the working face also increases as the blasting pressure relief position moves toward the working surface. Engineering practice results show that blasting cutting can effectively block the propagation of mining pressure, and the stress impact range is shortened by approximately 1/3.

Jul 31, 2021

By M. P. Miano

Matching the productivity gains of continuous mining machines with the ever increasing performance levels achieved by longwall units has required creative thinking to assure that development is completed in time for uninterrupted longwall production. By using management information systems to coordinate support operations, the most productive planning decisions can be made. This paper focuses on the role of computer technology tools in achieving improved productivity from both longwall and continuous miner sections. The primary emphasis is on the planning process and the methodology developed to guarantee the best allocation of management and manpower resources.

Jan 1, 1993

By Nikhil Dhawan, Ashwini Kumar, Yogendra Pratap, Himanshu Tanvar

India does not possess any soluble potash reserves and depends completely on imports. In this study, an attempt has been made to recover potash (K) values from the mica sample employing thermal and mechanical routes followed by leaching. Direct leaching of mica in different lixiviants is found to be ineffective with very low K-dissolution (1–5%). Heat treatment with different fluxes, such as NaCl, NaOH, and CaCl2, is carried out and almost 85% K-values are recovered. Mechanical activation of mica and with different calcium additives is carried out to recover potash values. K is recovered in leach solution in the form of soluble salts, such as K2CO3, K2SO4, and KOH, and leach residue consists mainly of calcium-alumino-silicates. Using mechanical activation with flux, it is possible to recover >95% K-values from mica sample. Mechanical activation with calcium-based flux is found sustainable in the recovery of K-values from mica.

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

By Harry M. Parker

Exploration for sandstone-type uranium ore bodies which will be exploited using underground mining techniques is usually executed in sequential fashion. Geostatistical methods can be used at the earliest exploration stages to design drilling programs which have a high probability of success in the location and delineation of mineable ore-grade mineralization, should such mineralization exist. In succeeding development stages, geostatistics may be used to outline and define the potential grade of reserves and to apply confidence limits on the grade estimation. Delineation of mineable reserves for mine planning requires extensive development drilling; using such drilling data geostatistical methods may be used to minimize the drilling needed to achieve a desired level of confidence in the calculation of mineable uranium ore grade and tonnage. Because sandstone-type uranium deposits tend to be pod-shaped and are generally aligned along a mineralized trend, this paper proposes a geostatistical method of calculating uranium ore reserves which accounts for this fact and predicts the area within a trend which is underlain by ore. This method uses an indicator value; that is, drill holes which contain mineable ore-grade intercepts are coded as 1, those that do not are coded 0. The indicator may be kriged over the mineralized trend to obtain an estimate of the area underlain by ore. The thickness and grade-thickness may be kriged, and the average ore grade may then be obtained by dividing grade-thickness by thickness, as is conventional for stratabound deposits. The mean grade is then multiplied by the kriged mean thickness to obtain an estimate of the volume, and thence tonnage, of mineable ore within the trend.

Jan 1, 1979

By Boleslav Taraba, Antonín Taufer

Thermovision monitoring of surface temperature has been examined for the purpose of detection of spontaneous combustion of early stage. Measurements were carried out in bituminous and subbituminous coal mines. It was found that surface temperature heterogenities can be considered as common phenomenon in mine openings. However, the most of the observed temperature heterogenities were not connected with coal spontaneous combustion of early stage. These, so called [non-spontaneous combustion] temperature heterogenities in surface of mine openings were found to be caused by: l. Different conditions of heat transfer between opening surface and air stream; 2. Low temperature (natural) oxidation of coal; 3. Dissipated heat loses of working machine. Sites of early stage spontaneous combustion of coal were characterized by: 1. More significant, local rise in surface temperature comparing with low temperature coal oxidation; 2. Evolution of carbon monoxide with local concentration near the surface of such site more than about 15 ppm (bituminous coals) or 30 ppm (subbituminous coals). INTRODUCTION Mine fires are a serious hazard to life and result in a considerable loss of coal reserves. Thus, great attention is paid to investigation of new methods enabling already early detection of self-heating of coal. The earlier a fire is observed, the easier would it be to deal with. Detection methods used in coal mines are mainly based on: 1. [Mine air analysis]. Changes in composition of mine air are examined. Products of spontaneous heating of coal, not being present in mine air under normal conditions, are considered as indicators of anomalous behaviour of coal (carbon monoxide, unsaturated hydrocarbons) (Mackenzie-Wood and Strang, 1990). 2. [Temperature measurements]. Sites of higher temperature level comparing surroundings are looking for underground using various direct or indirect methods of temperature measurements. This paper summarizes experience from thermovision monitoring, as one of the latest indirect temperature measurement technique, used for the purpose of early detection of self-heating of coal in mine openings. INFRARED THERMOVISION Infrared thermovision device of AGEMA Infrared systems AB (Sweden) was used for the in situ measurements. The constant value of emissivity factor, 0.95, was pre-set as the most probable level of emissivities of coal and rocks in mine conditions.

Jan 1, 1993

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By Keith Olson

In the heart of Appalachia, where coal mining has shaped communities and economies for generations, Bluefield State University (BSU) has made a landmark decision to reestablish its mining engineering technology program. This move comes at a critical juncture for both the university and the mining industry, which faces significant workforce challenges amid evolving technological demands and an aging professional demographic. The program’s revival represents an educational initiative and a strategic response to industry needs and regional economic development. Nestled in the mountains of southern West Virginia, BSU has a storied history intertwined with the region’s mining heritage. The institution’s decision to bring back this specialized program after a hiatus of several years signals a renewed commitment to serving both regional industry demands and providing career pathways for students in an area where the cyclical nature of resource extraction economies has often limited economic opportunities. “This program’s return reflects our deep understanding of this region’s needs and our commitment to preparing graduates for meaningful careers that support our local industries,” said Darrin Martin, president of Bluefield State University. “We’re bridging the gap between education and industry with a modernized curriculum that addresses today’s mining challenges while preparing for tomorrow’s innovations.”

Jun 1, 2025

By Alain A. Sonntag

The MBS Solvent Extraction System utilises a unique design of mixer- settler having very high capacity per unit area and great flexibility. The development of the mixer-settler is traced through its various stages wherein the independence of mixing and pumping, reduction in settler area requirements and simplicity of plant layout were achieved. The laboratory, pilot plant and full scale tests contributing to the development of the machine are described. The existing KREBS SX plants in Europe and Africa are described as well as the plants presently under design. Results of recent testwork are also given.

Jan 1, 1981

By E. P. Reed

We are proud that one of our predecessor companies originated the phrase "Safety First". That phrase remains today as the guiding principle that governs our total approach to safety and well being in U. S. Steel. U. S. Steel management is totally committed to this attitude and our objective is to have every employee as deeply conscious of his safety responsibilities. Safety is a state of mind but like most things it must have a physical side - both intertwined and inseparable. You might say each promotes the other; and this gives us confidence that with hard work, cooperation from all individuals, and proper application of knowledge and experience, our ultimate objective of frequency "0" will be attained. It is in this vein of thought we present a paper today which gives you briefly our progress, mainly in the physical, or mechanical, protection of miners at work in the Southern District mining operations of U. S. Steel. The Southern District not only includes the underground mining of coal but the underground mining of zinc ore in Jefferson City, Tennessee, and the quarrying of dolomitic limestone near Bessemer, Alabama.

Jan 1, 1970

By J. M. D. Wilson

The literature relating to binders in iron ore pelletizing is reviewed from the point of view of their established or proposed bonding mechanisms in green and dry pellets.

Jan 1, 1981

By R. A. Jankowski

Although the number of operating longwall mining systems has remained relatively consistent over the past five years, longwall production levels have increased significantly during this period. Longwall production currently accounts for approximately 50% of U.S. underground coal production. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems. This increased longwall productivity has meant that far more dust is being produced. An improved understanding of the longwall face ventilation system and advancement of face ventilation technologies are necessary to ensure all face personnel are allowed to work in an environment that is free of excessive levels of airborne respirable coal mine dust. The Dust and Toxic Substances Control Branch of the National Institute for Occupational Safety and Health's Pittsburgh Research Laboratory has examined several basic principles of the longwall face ventilation system, and has evaluated the effectiveness of numerous improved face ventilation techniques for longwall mining systems. These include identifying improved techniques for measuring face ventilation parameters on longwall mining sections and investigating the fundamental relationship between face air flow and the entrainment and dilution of respirable coal mine dust. Studies have been completed to determine the impact on face dust levels from using belt entry air to ventilate the longwall. Novel methods have been identified to increase the amount of face air flow and to manage face air flow to most effectively minimize face workers' dust exposure. Unique systems of auxiliary face ventilation have been developed and evaluated at full-scale, simulated longwall test facilities. The theoretical and applied aspects of each of these principles and technologies are discussed. Application of these results, throughout the longwall mining industry, as documented from surveys conducted in the early 1980's and 1990's, have reduced the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1998

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal's theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By K. F. Unrug

Martin County Coal Corporation is located in Martin County, Kentucky in the Appalachian coal fields, near the West Virginia border. The total leasehold covers more than 33 000 acres. Total annual production at Martin County Coal Corporation is currently 2,500,000 tons, but in certain years exceeded 3,000,000 tons. Approximately 45 percent of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal Corporation's work schedule consists of 240 days/year, two nine-hours shifts/day.

Jan 1, 1991