Search Documents

By James R. Walsh

While flue gas scrubbing with alkaline solutions is one of the oldest methods of removing SO2 from flue gas, a satisfactory scrubbing system for this application, which is both technically and economically viable, has yet to be developed. Interest in alkaline scrubbing has continued because of its basic simplicity and comparatively low capital cost. Drawbacks of alkaline scrubbing are the tendency for accumulation of solids to plug the system, scaling, corrosion and erosion problems and the need to dispose of large quantities of waste. Discussed are instrumentation loop applications to a 90,000 cfm alkali scrubbing test facility, the process problems the instrumentation engineer faces in. selection of equipment, the performance of the instruments selected and the problems encountered during start-up. The Test Facility incorporates centralized electronic process control with a digital data acquisition system provided to log process variables and print off normal (alarm) conditions. Flue gas SO2 content is measured by ultra-violet analyzers and analysis of the total gas stream is by gas chromatographs.

Jan 1, 1973

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By Frank Matter

The production of ultrafine slurries and powders is possible with small media made out of Si02, A1203, Fe203, Zr03 or other raw materials due to the fact that since approximately 12 years from now, entirely new machines have been developed which allow to use this small media for the production of ultrafine pigments. Basically we distinguish between two grinding methods which are: A.) Dry Grinding with Air Classification: This method is used for more than fifty years but only since four years this technology is realized with small grinding media. Many problems like cooling, abrasion, control of the media flow, separation media from product, grinding media recycling etc. had to be resolved before it was possible to get in full production with this new system. Hereafter a flow-sheet of such a TRZK mill with an air classifier especially designed to produce end products with a top size between 2,5 and 3,0 micron and with an average particle size between 0,3 and 0,5 micron.

Jan 1, 1983

By Van E. Housman, Stephen D. Hoffman

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), also known as "Superfund", requires a listing of sites that have known releases or threatened releases of hazardous substances, pollutants, or contaminants throughout the U.S. When EPA determines that a significant threat exists, it places the worst contaminated sites on the National Priorities List (NPL). CERCLA provides EPA broad authority to clean up hazardous sites that threaten human health and the environment. There are currently 52 sites on the NPL that were placed on the list because of high human health or environmental risk as a result of non-coal mineral extraction, beneficiation, or processing operations. This list covers mining sectors from aluminum to zinc. While some of these sites were abandoned, many are still operating. (There are additional mine sites that have been recently proposed to be included on the NPL that are not included in this paper.) EPA is continuing to develop a mining program to address human health and environmental threats from active non-coal mines. EPA has performed a comprehensive study to assess the waste management practices at all of the 52 mine sites on the NPL. In addition, EPA is continuing to collect information on the specific mining sectors (i.e., gold, copper) that represent many of the NPL mine sites. One of the goals of this effort is to attempt to identify the types of mining practices that lead to human health and environmental problems at the NPL mine site. EPA estimates that there are currently 500 to 1,000 active mines (not including placer operations). While some mining NPL sites began operations before the turn of the century, only a handful of the NPL mines entirely ceased operations prior to 1970. Of the 52 NPL sites studied by EPA, 12 are currently active. By definition, these mines represent current mining practices. Approximately 17 additional NPL mines that ceased operations between 1970 and 1990 represent some degree of current mining practices. Therefore, at best, less than half on the 52 NPL mine sites can be said to definitely represent past mining practices. Although some mining waste management practices have changed over time, the basic technology for extraction and beneficiation of mineral ores have remained fairly constant over the last fifty years. While the use of acid to leach copper dumps, the use of cyanide to leach gold in heaps, and the spread of solvent extraction techniques has changed some aspects of mining, the basic operation of removing ore from the ground and concentrating it through beneficiation has remained fundamentally the same as when most of the non-active

Jan 1, 1992

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By V. F. Hollister

Although it is apparent that porphyry copper deposits may have formed in the Andean orogen from Permian time onward, commercial deposits thus far developed appear to have Cenozoic ages only. Following Chilean useage, the porphyry deposits are divided into either: (a) a stockwork, or (b) a tourmaline breccia model. Stockwork type deposits tend to occur on major strike-slip structures which may be either transcurrent or transverse faults related to plate movements, while the tourmaline breccia type may more frequently form independently of regional faults. Stockwork types may be conjugate fractures that intersect and ramify as a network of veins and veinlets, cutting altered rock, and genetically related to a major regional fault, or in other cases they may reflect the intersection of two large fault structures. Circular fracture patterns may more rarely occur in stockwork deposits in response to a specific intrusive. Tourmaline breccia types are characterized by circular and radial fractures genetically connected in some way with tourmaline breccia pipe development or an intrusive piercement that preceded it. Each structural model contains mineralized intrusive8 which have a close time-space relationship to ore and in each model, mineral paragenesis is similar, regardless of age or location in the plate. Also, each model contains the same type of alterntion halos (phyllic, argillic, prophllitic) as are developed in intru- sive centers in porphyry copper deposits found in North America. The potassic zone is exposed best in the older deposits. Examples of each type of deposit are illustrated, demonstrating the feature evolved.

Jan 1, 1973

By Keat Chuan Chew, Qiao Yue Tung, Teoh Yaw Poh

"1 INTRODUCTION With a land area of 718 square kilometres housing a population of slightly over 5.4 million, as of 2014 (Department of Statistics Singapore 2015), Singapore is a highly urbanised city. Transport infrastructure is critical to keep the country and economy highly connected and functional as the population in Singapore continues to grow. The importance of a robust transport infrastructure is recognised by the Ministry of Transport in Singapore, which is working towards bringing 8 in 10 households within a 10-minute walk of a train station by 2030 (Ministry of Transport 2015). This gives rise to the rapid expansion of the rail network in highly urbanised Singapore, resulting in more tunnelling work having to be carried out in closer proximity to existing buildings. Such tunnelling work is expectedly more challenging and complex, and if not managed effectively, will impose higher risk to the adjacent buildings. Hence, the Building and Construction Authority (BCA) has implemented specific control measures to mitigate such tunnelling risks and to ensure safety of the public. 2 CHALLENGES FACED BY TUNNELLING WORK IN SINGAPORE 2.1 General Challenges of Tunnelling in Singapore With the increasing densification of the rail network in a highly urbanised setting, rail projects in Singapore are faced with several key challenges. One such construction challenge is constrained construction sites brought about by network intensification. Alongside the growth of the rail network, shown in Figure 1, other infrastructure networks in Singapore are also continuously growing. Underground interchange stations between networks become increasingly common, forcing each underground interchange station to be constructed deeper and in closer proximity to existing buildings (Figure 2). Singapore is not alone in facing this issue. The same can be observed in cities like London, in which its myriad network of subway lines pushes new lines and interchange stations to be constructed deeper."

Jan 1, 2016

By Samuel Polinsky, Lawrence W. Bierman, Wayne Perkins

[A column float beneficiation plant using 9, 8.5 foot diameter, cells was constructed by the Simplot Company and the Smoky Canyon Facility in the fall of 1986 and has been in operation since May of 1987. The float beneficiation process was developed jointly by the Simplot Company and the Bureau of Mines (Salt Lake City, Utah) which incorporates the Bureau's bubble generator design and chemistry system based around the reverse float technology, (Albany Bureau of Mines, Application of Carbonate-Silica Flotation Techniques to Western Phosphate Materials, Rule, Dallenbach , Larsen, RI8728, 1982) . This chemistry has been modified by Simplot in both patented and unpatented improvements. The objective of the beneficiation process was to reducethe A1203 content in the overall pipeline concentrate by 0.2 wt z. Therefore, a process stream was identified in the mill circuit which provided an opportunity to isolate and treat 1100 tons per day of poor quality phosphate concentrates The process allows recovery of approximately 15% of the mill concentrates, otherwise unsuitable for fertilizer production. The alternative would have been to waste this ore. Wasting would have resulted in considerable ore loss, increased mining costs and required additional products grinding. ]

Jan 1, 1989

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 1/4 to 1/2 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100' to 300' in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1986

By Irwan Halim, Seung Han Kim

This paper will describe design of precast segmental tunnel lining for the Pawtucket CSO Tunnel Project in Providence, Rhode Island. The tunnel is 11,700 LF long with 30-foot finished diameter to be constructed in complex sedimentary rocks. Special features of the segments include a large keystone and no connector used on radial joints. The typical segments will be steel fiber reinforced, and hybrid segments with additional steel rebars and shear bicones will be used around the adit openings without use of any structural framing. The important design considerations will be discussed, including special 3D segment to adit connection analyses performed.

Dec 1, 2022

By J. T. Carlson

Dolomite is an objectionable impurity in phosphate ores, due to its MgO content. Even though dolomite and apatite liberate at a coarse size, the very similar densities of dolomite and apatite makes density separations difficult. However, if operated correctly, jigging can be a very efficient process. This has led to the development of a unique laboratory scale jig that allows for easy alteration of effective jigging properties. Key jigging parameters have been investigated for the separation of dolomite from phosphate ores. It was found that a pulsation rate of approximately 200 pulses/minute worked best for separating dolomite from apatite.

Jan 1, 2010

By B. Bag

Saturated and unsaturated fatty acids are used in the flotation of iron values present in iron ore. Among the several fatty acids, oleic acid and its sodium salt are widely used. To substantiate the flotation results, the quantum chemical calculations of a few such acids have been carried out by adopting the semi-empirical AM1 method. These acids have been further optimized in the presence of an iron atom. The electronic interaction of the polar carboxylic head group of oleic acid with the iron atom is higher compared to the other acids. The numerical results support the flotation behavior of iron ore with oleic acid. Key words: Iron ore, Flotation, Fatty acids, Quantum chemical calculations, Semi-empirical AM1 method

Jan 1, 2009

By John E. Frost

Duval's (now Battle Mountain Gold Co.) copper and gold deposits in the Battle Mountain District in Nevada are in two subdistricts - Copper Basin and Copper Canyon - about 18 km (11miles) apart. Location of the two subdistricts is shown in Fig. 1. The two centers of mineralization have distinctive geologic and ore characteristics that required different innovative approaches to exploration and development. Nearly all of the copper from Copper Basin has been recovered by heap leaching. Because of relatively high gold and silver values in the Copper Canyon ores, a significant part of the sulfide copper ores has been recovered by a conventional flotation mill at Copper Canyon. Recently, this mill has been converted to the recovery of gold that is mined from zones peripheral to the copper deposits. Prior to Duval's entry, small amounts of copper, gold, silver, lead, zinc, and antimony had been mined in the district over a nearly 100 year period, beginning in 1866. The bulk of the $13 million total production to 1962 was derived from copper and gold lode ores and gold placers. Duval's interest in Battle Mountain-arose directly from a submittal by Asarco, which controlled key claims in both the Copper Basin and Copper Canyon subdistricts. Asarco acquired its holdings in the district in 1959 and undertook limited exploration until mid-1961. At that time, the company decided to dispose of its interests. Duval was invited to evaluate Asarco's properties and accepted. On Dec. 6 and 7, 1961, J.E. Frost, R.C. James, R.W. Sayers, and H.A. Schmitt, representing Duval, and K. Richard and E.W. New- man, representing Asarco, visited Copper Basin and Copper Canyon. Frost concluded that the properties were of considerable interest and prepared, by Jan. 12, 1962, a voluminous report recommending that Duval acquire and explore Asarco's properties. Furthermore, he recommended a large initial exploration program that included not only geologic mapping, geochemistry, and geophysics, but also the extensive drilling that was to involve, as the first phase of exploration, 49 drill holes in Copper Basin and 21 drill holes in Copper Canyon. Following property agreements between Duval and Asarco, and Duval and several other claim owners, geologic mapping, geochemical surveys, and drilling began in August 1962. Exploration drilling was completed in July 1964 and engineering studies in April 1965. Development of the Battle Mountain properties was authorized in July 1965, and production commenced in the first quarter of 1967. Because of the unusually high oxide copper content of the ore bodies, particularly in Copper Basin, a much larger than typical proportion of the copper in the deposits has been recovered by heap leaching. The generalized geology and ore zones of the Copper Basin are as shown in Fig. 2 and of Copper Canyon in Fig. 3.

Jan 1, 1991

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By J. A. Bradbury

N. A. Degerstrom, Inc. has constructed and operated a processing plant approximately five miles north of Soda Springs, Idaho for processing a byproduct phosphate treater dust from Monsanto's elemental phosphorus plant, also located in Soda Springs. The plant is designed to produce agricultural-grade phosphoric acid, gallium, and silver. The design capacity of the plant is 54.4t (60 st) of treater dust per day, which can produce 16,326t (18,000 st) of phosphoric acid, 6,600 kg of gallium, and 6,033 kg (194,000 oz.) of silver per year.

Jan 1, 1993

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing' of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By Angelus S. C. Owili-Eger

Although the foundation of a unified treatment of fluid flow in variably saturated porous media was established more than seventy years ago, no serious attempt was made to develop it until the early 1970's. Ever since, a number of unsaturated-saturated numerical models have been reported in the literature. However, none of these models have treated multidimensional, multiphase flow in deforming media, parts of which may undergo extensive secondary fracturing. A situation such as this is not uncommon in coal mining operations in which the longwall method of extraction is employed. The present model has been structured to handle such physical systems. This paper presents the mathematical formulation, the numerical algorithm, and a further validation and evaluation of the modified model. The model treats a multiphase flow in a three- dimensional regime and handles mining excavations of complex and changing configurations.

Jan 1, 1980

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.