Search Documents

By R. S. Ondrey, R. A. Haney, T Tomb, R. T. Stoltz, Novakowski D. L. Chiz, E. J. Gerbec, D. J. Atchinson

Although the number of operating longwalls in the United States (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and in some cases more than doubled. As a result of this production increase, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Methods being used to control dust were noted, with special emphasis placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control practices in place at the time of the visit to dust concentrations measured at the tail and on the tail shearer operator and to the average of all the dust concentration measurements from the occupations sampled. The methods used to control dust were also compared to the gamut of methods known to be available. This paper presents a discussion on the effectiveness of the methods being used to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1991

By J. Larsson

In the pursuit of increased safety the mining industry has worked to develop systems for remote control and autonomous operation of both stationary and mobile equipment. This paper reports on a newly developed system for teleoperation and autonomous tramming of LHD (Load-Haul-Dump) mining vehicles that not only increases the safety of the operators, but also has the potential to increase productivity.

Jan 1, 2010

By Donald Bishko

Zoning is the legal means by which land use can be controlled. Although zoning laws have historically been quick to prevent quarrying, one is hard pressed to find zoning ordinances which specifically state that land should be used (or held in reserve) for quarrying and prevent other uses such as recreation, housing, etc. This situation is especially true when the mineral to be quarried has a low intrinsic value such as sand, gravel, and crushed stone. The chance of a gold mine surviving urban sprawl is probably considerably greater than that of a sand and gravel pit, even though it is possible that the dollar value of the sand and gravel' would exceed that of the gold mine. The research reported herein was concerned with two major topics: to delineate the real costs associated with the non-protection of our construction aggregate resources (growth minerals) and to develop a computer simulation model which would aid planners in making economically sound decisions. This paper describes the problems faced by the mineral aggregate industry and discusses the role of computer simulation in planning problems. It briefly describes a simulation model which has been developed and previously reported12 and discusses the results of a pilot study conducted on the Tri-City area (Albany, Schenectady, and Troy, New York). 3

Jan 1, 1970

By Y. Xi

In this paper we present an availability approach for determining the capacity of a major bucket wheel excavator (BWE) system to be used in Yuabaoshan surface coal mine in China. Based on previous time studies on other BWE systems for delay times due to internal and external causes, and a four-level maintenance and repair schedule, we develop a model taking into account all random failures and present a fast and simple solution to this highly complex problem. A procedure employing the Markov renewal theory for determination of the distribution of random failure times and failure rate of the whole system, as well as some other factors useful for calculation of the overall system capacity are discussed in the paper.

Jan 1, 1993

By D. Spitty

There are enormous complexities with mine planning and the problem itself presents a huge challenge to the existing mine planners performing this activity. Mine planning optimization supports planners to determine ?What are the best increment excavation sequence and the best material blending combination such that throughput, quality, cost, utilization and Net Present Value (NPV) targets are met?? It is achieved through using an advanced scientific approach that has been specifically adapted to address the mine planning dilemma.

Feb 23, 2014

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By N. L. Dorset, K. L. Heasley

Unfortunately, mining and mining accidents have gone hand-in-hand since man first started to extract ore from the ground. In the first published treatise on mining, De Re Metallica, Georgius Agricola (1556) stated that cold, water, dust, stagnant and foul air, roof falls, falls from ladders and demons all caused injury and death in the mines of his day. Although demons are no longer considered a cause of accidents in modern mining, the other factors remain with us still. The United States government started keeping track of fatalities with the establishment of the federal Bureau of Mines in 1910. Successor agencies, such as the U.S. Mine Safety and Health Administration (MSHA) continue to track fatalities today. Looking at the records, it can be seen that coal mine fatalities dropped from 2821 in 1910 to only 27 in 2004. The reduction in fatalities and injuries didn’t “just happen.” It took concentrated effort from the entire mining industry: miners, supervisors, safety officials, mining inspectors and mining researchers. But first, specific hazards must be identified before they can be corrected. In past, coal mining accidents have been analyzed by: type (roof fall, electrical, etc), mine attribute (location, seam height, etc.), and aspects of the mineworker (work experience, job classification, etc). Much of this research helped to direct the industry’s attention to where additional vigilance and safety training was needed. No doubt this directed effort has led, at least in part, to the decrease in coal mining fatalities. This paper takes a novel look at coal mining fatalities: it examines the risk of fatalities based on how long the mine has been open.

Jan 1, 2006

By M. Adnan Göksel

Pyrite cinder is generated by roasting pyrite for sulfur dioxide production. It contains up to 62% iron, but also may contain other hazardous or toxic materials such as Zn, Pb, As, T1, Cd, Cu, Sn and S. Furthermore, the physical characteristics are not properly suited for conventional sintering. As a result pyrite cinder is considered to be unsuitable for iron and steelmaking or for outside storage because of its potential for causing environmental problems. In recent years industrialized nations have put increasing pressure on the manufacturers to either use such waste products or properly dispose of them. In this study, solutions to both the iron recovery and disposal problem were attempted by pelletizing the pyrite fines with internal carbon. The pellets, after hydrothermal hardening, were reduced and melted in a furnace for hot metal production. Hot metal of usuable quality was produced and the hazardous materials were either collected with the fumes or in the slag.

Jan 1, 1984

By P. D. Rao

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. Coals from Usibelli Coal Mine and the Beluga coal field have a heating value of approximately 8,000 Btu/lb and 28% moisture. Hydrothermal treatment (at 275 to 352'C) of lump coal from Usibelli Coal Mine and Beluga coal field enhanced the heating value of the coal, on an equilibrium moisture basis, from 8,000 Btu/lb to nearly 12,000 Btu/lb. The product coal with high heating value and 0.2 % S is an environmentally acceptable premium fuel. The Hardgrove grindability index of the coal is greatly improved, further enhancing its value. Increase in hydrothermal drying temperature promotes vesiculation of resinite. Vitrinite reflectance increased to 0.72 and vitrinite was subjected to widespread visiculation resulting in a coke like structure indicative that the material went through the fluid stage.

Jan 1, 1991

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

By Arvid E. Anderson

The paper describes the unique operating features of the Lebanon Concentrator Plant wherein both magnetic concentration and froth flotation are used. Chalcopyrite is selectively floated by the use of dual collectors, Aerofloats and secondary butyl xanthate. Both potassium ethyl xanthate and sodium isopropyl xanthate (dual collectors) are dissolved and emulsified with pine oil for the flotation of the pyrite. Sketches describing the plant operations are presented and plant operating metallurgical results obtained are also given. The optimum production of minerals by the froth flotation process is normally achieved [ ] smooth operating conditions, The process, because of its many variables, becomes an art as well as a science. Therefore, any phase of the operation which will aid the operator in his control of the numerous variables will help produce a smoother operating plant, One of the most important variables which the operator deals with is the addition of reagents, These are usually costly items and should be used discretely with minimum amount of waste, The danger is that ,this emphasis may reduce the reagent amount to a point below that required, or, on the other hand an excessive amount is added, Both conditions usually yield poor results. The drea of the metallurgist is to provide the operator with the tools enabling him to produce a good mineralized froth at all times. Normally the operator has no control concerning the type of reagents which he must use. This has usually been worked out for him in the laboratory and by plant-scale tests. He does have limited authority to control the amounts of the reagents at his disposal. This, I believe, is as it should be. However, the operator should be provided with the best combination of reagents for his particular job. The providing of this combination of reagents for his particular job, The providing of this combination is often difficult, yet it is very important in order to yield good results, With this in mind, the dual collector idea was introduced for the selective flotation of chalcopyrite, and also later for the flotation of pyrite at the Concentrator Plant of the Bethlehem Cornwall Corporation in Lebanon, Pennsylvania, Supplying several types of collectors has given the operator an additional effective tool, even though great variations are encountered in ore tonnage treated and in ore composition, This paper deals with the use of the dual collectors and with the addition of the reagents in the form of a pine oil emulsion, or more accurately, a pine oil suspension. It is hoped that other operators may find the ideas helpful. There does not seem, to me, to be definite scientific fact which would substantiate the necessity for the use of dual collectors. However, in actual operations, the metallurgical results at Lebanon became more uniform with the use of dual collectors, I look upon it as an "insurance policy" which greatly aids the operator during those periods when he is having trouble, One theory has been advanced, i.e. one collector has a greater tendency to float the coarser minerals, whereas the other one may float the finer ones. Consequently, a combination of the two collectors will result in optimum recoveries, There has been some evidence that this is true, but it is not conclusive, on the other hand, the use of a xanthate-pine oil suspension (or emulsion) should speed up the surface reaction of the collector with the sulfide minerals, result¬ing in more uniform flotation, This has definitely happened in our particular case. A more interesting unexplainable observation has also occurred; i.e., the xanthate solution does not appear to lose its strength as rapidly when it is in the form of an emulsion (or suspension), This was first observed when a 50 gallon drum of a 20% ethyl xanthate solution was taken to Wilmington, Delaware, for a laboratory test, using a homogenizer to produce the xanthate-pine oil emulsion. Upon arrival, the drum of xanthate had developed a considerable internal pressure, The relief of this pressure was accompanied by a strong odor, When the emulsion was returned to Lebanon for the plant test orders were issued to release the pressure prior to emptying the emulsion. Nopressure had developed within the drum and there was no unusual odor present, Since this time it has been observed that xanthate pine oil suspensions have greatly decreased the possible decomposition of the xanthate solutions. In fact, suspensions have been exposed for more than a month without apparently effecting their reactions in the flotation plant. On the other hand, we found that the regularly mixed concentrated xanthate solutions, after standing for several days, did not give the same results as the freshly made ones. This effect was greatly reduced by the use of xanthate pine oil suspension (or emulsion)

Jan 1, 1958

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

Like the Summer Olympics and U.S. presidental elections, MINExpo comes along once every four years. More than 35,000 people attended the last MINExpo and there is talk that there will be more this time. Just about every company that has anything to do with mining, 1,822 to be exact, will exhibit their wares at the show, but it is the ones rolling in the massive equipment that make MINExpo the show that it is. The following is a glimpse at some of the companies and equipment that you can expect to see at this year?s MINExpo.

Jan 1, 2012

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By S. E. Phillipson

Four massive pillar collapses in limestone mines, and one in a marble mine, occurred between 2011 and 2021 in benched areas at the Appalachian physiographic province. We characterized the rock mass at 43 limestone mines using the Geological Strength Index and, by plotting the results on a physiographic relief map, determined that GSI values between 55 and 70 preferentially occur in the Appalachian and Ouachita Mountains, which were subject to deformation during the Ouachita and Alleghanian Orogenies. Limestone mines located in formations of similar age in the Interior Plains, where deformation was less developed, are characterized by Geological Strength Index values over 80. We present the results of pillar strength calculations that incorporate the Geological Strength Index from mines that experienced massive collapse, as well as from mines with benched areas that did not collapse, to demonstrate the negative effect that a jointed rock mass has on pillar stability. We suggest that pillar designs, particularly those in which benching will be incorporated, should include allowance for rock mass quality. Because of the preferential dominance of lower GSI values in the Appalachians, we further suggest that pillar designs in this environment may require additional engineering assessment, especially where benching is intended. Lower GSI values may often translate into greater overbreak, which results in loss of pillar volume, corresponding wider back spans, and a decreased width-to-height ratio.

Jun 25, 2024

By Bruce A. Kuyper

Routine core drilling at the Cove deposit failed to confirm gold-silver grades and length of intercepts observed in reverse circulation drilling. A drilling program was designed to ascertain whether the disparity was due to problems with reverse circulation drilling techniques, core drilling techniques, or the erratic nature of the gold-silver mineralization. Special sampling devices and core drilling methods were employed. Data obtained from core-reverse circulation twins showed that down-hole contamination during reverse circulation drilling accounted for much of the variation between reverse circulation and core drill results. Down-hole contamination occurred as a result of high ground-water inflows eroding friable vein material from hole walls.

Jan 1, 1991

By J. F. Burr, D. Snyder, W. Calder

"INTRODUCTION “Explosion protection” refers to techniques used to minimize the potential for electrical and electronic equipment to create an ignition while operating in a hazardous location (HAZLOC). In particular, U.S. coal mines are required to use equipment in certain areas of the mine that has been approved by the Mine Safety and Health Administration (MSHA) for use in a methane and coal dust environment to limit the risk of the equipment creating an ignition-capable spark or a thermal energy ignition. In general, MSHA’s regulations for explosion protection recognize two techniques: the use of explosion-proof enclosures (XP boxes) and 2-fault intrinsic safety for electrical and electronic equipment. For 2-fault intrinsically safe (IS) equipment, the U.S. mining industry requirements are unique in that the equipment is certified by MSHA. The criteria MSHA uses to evaluate equipment for intrinsic safety, as required by Title 30 of the Code of Federal Regulations (30 CFR) [30 CFR, Sections18.20(b), 18.68(a)(1), 19.1(b), 20.1(c)(2), 22.6, 23.6, and 27.20(a)], is published in a document referred to as ACRI2001 (1). Outside of U.S. underground mining, many industries and countries accept equipment that is designed to a consensus-based international standard (ANSI/ISA 60079-11 is the U.S. version). The purpose of this study is to provide an overall assessment of the ANSI/ISA 60079-11 standard on 2-fault intrinsic safety and the MSHA ACRI2001 acceptance criteria, and determine if the ANSI/ISA document can be an alternative to ACRI2001 while maintaining an equivalent or better level of safety for miners. There are many drivers for this study. First, immediately after the 2006 MINER Act (2) was passed, there was a perception in the industry that the unique MSHA requirements were contributing to delays or restricting the availability of equipment to meet the requirements of the Act. Additionally, the MINER Act required that mine operators submit an accident response plan for MSHA approval, to be reviewed every six months. MSHA is required to determine if these plans reflect the most recent credible scientific research and make use of currently commercially available technology. There is a concern, as expressed in a recent National Academy of Science (NAS) study (3), that the unique requirements for U.S. mining may be limiting the technologies available to coal miners and technology options for mine operators. Accordingly, the study recommended that the National Institute for Occupational Safety and Health (NIOSH) and MSHA re-examine their technology approval and certification processes to ensure they are not deterring innovation, and explore opportunities to cooperate with other international approval organizations to harmonize U.S. and international standards without compromising safety. Lastly, the National Technology Transfer Act (NTTA) and the accompanying Office of Management and Budget’s OMB-119 circular mandate the use of consensus-based standards by federal agencies. However, for U.S. mining operations, MSHA cannot accept such standards unless a determination is made that such standards provide an equivalent level of protection for the miner, per the requirements of the 1977 Mine Act, the 2006 MINER Act, and 30 CFR Part 18 regulations."

Jan 1, 2017

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without being reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county road and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Jan 1, 1997

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology's Process Insights neural network software and Oil System's PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995