Search Documents

By Jack G. Crump

Nuclear radiation systems for gauging solids content in process slurries and level in crushers has demonstrated acceptance in ore processing. The use of nuclear radiation for moisture analysis of bulk materials is presently receiving acceptance in beneficiating and agglomerating processes. On the horizon is the use of nuclear activation methods for continuous, qualatative and quantitative analysis of concentrate. The common characteristics of these uses of radiation is the non-contacting nature of the measurement. Unquestionably, this is the dominant reason for acceptance of nuclear methods in level and slurry-gauging. Moisture activation analysis of a product using nuclear methods retain this advantage. However, and: more importantly, they offer new solutions to old problems. The nuclear method in addition to being non-contacting, is non-destructive and provides a continuous measurement of the process variable. The system responds: to the fundamental makeup of matter, mass and elemental composition, not to secondary properties such as temperature, resistivity, or dielectric constant. Measurement is a volume rather than a surface phenomenon, thus the results can provide a truer pricture of the measured variable.

Jan 1, 1965

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By D. C. Torre

Ever since the early '60's there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the continuous haulage systems which have been most successful to date were placed in operation in the early '70's and were all of the bridge conveyor type, usually consisting of bridges and mobile bridge carriers attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor type continuous haulage systems were, and continue to be, either of the belted or chain type. Undoubtedly, the most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Company. Until early 1977, the most successful chain conveyor type haulage systems were manufactured and marketed by Jeffrey Mining Machinery Division. In 1977, Long-Airdox reentered the market with a chain type system to complement its belted system. I say "reentered" because the original bridge type continuous haulage system was introduced to the coal mining industry in the early '60's by the old Long Company, a predecessor of the current Long-Airdox Company, and those original units were of the chain conveyor type.

Jan 1, 1981

By E. Kenneth Siroky

The concept of ultrasonic measurement was originally applied to marine operations. Sonar . . . standing for Sounding, Navigation and Ranging, was developed for military uses. Today Sonar has become very important to the fishing fleets and marine construction industries where its applications cover a wide range of uses our company, in addition to the inair ultrasonic equipment as discussed in this paper, is also deeply involved in marine sonar and works primarily with oceanographic research and fishing industries. Ultrasonics, by simple definition, are sound waves beyond the audible range of the human ear and are generally accepted to be waves over 20,000 cycles per second. When applied to level measurement, the principles of ultrasonics are basically quite simple. A sound pulse is initiated at a point in time and the time interval for the echo from that pulse to return can be interpolated into distance. The speed of sound in air under standard conditions is approximately 1,100 feet per second, or if converted into more meaningful information as related to distance measurement, the time required for sound to travel one foot round trip is 1.78 milliseconds. An early application for ultrasonic level monitoring equipment was in large grain elevators. Prior to ultrasonics, the common practice of inventory measurement was to have an employee walk around the top of these large grain elevators, which are often over 100 feet above ground level, and drop a weighted rope or chain down into the silo to determine the level of the grain. Needless to say, this was a slow process and could be extremely unsafe, especially during windy and snowy weather conditions. An alternate

Jan 1, 1971

This paper presents the latest developments in the flotation model being developed collaboratively between the Julius Kruttschnitt Mineral Research Centre in Brisbane, Australia, and the Mineral Processing Research Unit of the University of Cape Town in South Africa as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. It includes: - characterisation of flotation cells using the bubble surface area flux, Sb; - relationship of Sb to the overall flotation rate constant; - determination of the froth recovery factor; - evaluation of ore floatability; - modelling of entrainment - development of the Floatability Characterisation Test Rig (FCTR); - use of the model in design and optimization of flotation plants; and - current and future work.

Jan 1, 1999

By A. T. Iannacchione

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels. 1 Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m (26.5 ft) above the miner's head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roof beam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999

By Edward J. McNamara

Sulphur as an element has been used for centuries. The technique of storing, handling and transporting it in its various forms has changed through the years. Freeport Sulphur Company, a division of Freeport Minerals Company, has produced sulphur since 1912. The first storing and transporting of this product as a liquid began in 1947. Significant environmental problems occurred in the handling of solid sulphur in the late fifties and early sixties. Since the sulphur WAS produced in the liquid form and the major customers used it in the liquid form, it became obvious that a liquid transportation system was the solution. The liquid sulphur delivery eliminated the dusty and hazardous handling problems and the contamination of the sulphur by dirt, acid, moisture and other materials. The remelting by the customer to use the sulphur is thusly eliminated with a savings in energy. In addition, this change in the mode of handling permitted a broad development of new sulphur mines in the marshy coastal area of Louisiana and offshore in the Gulf of Mexico.

Jan 1, 1978

By J. A. Haggman

In a country richly endowed in mineral wealth, Climax Arimco Mining Corporation's (CAMC) Dinkidi porphyry Au?Cu deposit in Nueva Vizcaya province, Philippines, represents the most significant mineral discovery in the country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon a region previously unassociated with porphyry-style mineralization. Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.41 % copper. Regional exploration throughout CAMC's 37,000 hectare FTAA has identified a further sixteen potential porphyry-related deposits. A new mining law was passed in March 1995 but prior to that CAMC had the first Financial and Technical Assistance Agreement (FTAA) granted by the Philippine government allowing 100% foreign ownership of mining projects.

Jan 1, 1997

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By Robert D. Harris

In 1958, the coal industry, through Bituminous Coal Research, Inc., and the electric utility industry, through the Edison Electric Institute and the Association of Edison Illuminating Companies, initiated a joint program to study coal pyrite and its removal as a means of lowering the sulfur content of steam coals. It was assumed that significant amounts of pyrite often remained in washed steam coal not because available systems for coal cleaning were inadequate, but because the pyrite was small and widely disseminated, During the first two years, samples of coal were examined petrographically to determine the size, association, and mode of occurrence of the pyrite in the raw coal and in the products of laboratory separation, Samples of coal were also pulverized in different equipment to determine how effectively pyrite was released by pulverization and if the mode of pulverization affected the liberation of pyrite. From these studies, the following tentative conclusions were made (1 ): 1. Much of the coal pyrite is within a 250-70 micron size range, and therefore is too small to be removed by conventional coal cleaning, but relatively large when compared to the size of coal as pulverized for combustion in large boilers. 2. The degree of pyrite liberation is mainly determined by the size of the product and not by the type of crusher. 3. For improved pyrite removal, the coal should be cleaned during or after pulverization at the power station.

Jan 1, 1965

Dravo Corporation was founded in 1891 and has long been recognized as a major domestic engineering and construction firm headquartered in Pittsburgh. In 1977, Dravo had revenue of $852.2 million with international business activities contributing $248 million; quite a different picture than envisioned at the turn of the century. Engineering and construction activities still dominate Dravo's most recent history and will do so for the immediate future. However, fluctuations in capital spending by large industrial sectors of our economy during the late sixties were affecting Dravo's planning for continued growth along its traditional lines of business. Diversification was a possible solution to smooth out the upward trend in corporate earnings. One large result of these continuing efforts was the formation of Dravo Lime Company, a vertically integrated, proprietary chemical supplier for the air pollution control market. Briefly retracing the seventies, the passage of the Federal "Clean Air Act" in 1970 supplied the impetus for Dravo Lime Company. This law promulgated limits on the emissions of sulfur dioxide (SO2) from large stationary sources that would affect local air quality. The major industry that felt the brunt of this regulation was the electric utility industry, especially those generating electricity with coal-fired boilers. The law hastened the development of a new industry, flue gas desulfurization (FGD), and is composed of three major segments: (1) the electric utility, (2) the FGD equipment suppliers (the scrubbing modules), and (3) the scrubbing chemical suppliers. Dravo's experience suggested the equipment end of the business but market analysis indicated that our long range corporate goals could be better attained by investigating the chemical processes involved in the removal of the SO, gas. The result being Dravo Lime Company. This paper will briefly describe the Thiosorbic lime scrubbing process and review our innovative mine and calcining facility.

Jan 1, 1978

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992

By H. Marshall Farrier

In the past few years the world petroleum industry has increasingly felt the weight of changes in the principal economic factors affecting pro¬fits. As a result of, these changes, it has been necessary for many oil companies to acquire certain new facilities in order to strengthen their competitive positions and thereby protect their tremendous investments in crude oil reserves, pipe line facilities, refining operations, and marketing outlets. Principally these needs have been met by new capital outlays. A supplementary, method of acquiring needed facilities, however, has been to obtain existing facilities through complete or partial acquisition of other companies.' properties. It is this method of meeting competitive pressures with which this paper is concerned. This paper presents a statistical breakdown of the mergers and acquisitions which occurred in the oil industry between January 1, 1954, and October 1, 1959, showing the frequency' with which certain types of properties were acquired in each of the years studied. In addition, it discusses the principal economic conditions which stimulated many of these property trans¬fers, comments on the effects of these mergers on the consuming public, and indicates the types of, mergers and the rate at which they may be expected during the next three or four years. The basic data upon which the statistical analysis presented in this paper is based were taken from several published sources. Obviously they are somewhat incomplete because not all mergers and acquisitions were reported However;, a careful search was conducted through, The Wall Street, Journal, The Oil and Gas Journal, Potroleum Week, and The Oil Daily with the result that the data should be reasonably complete and comparable for each of the years studied, It is believed, therefore, that the statistical analysis which' follows provides a reasonably accurate indication of the general trend in mergers and acquisitions during the period studied.

Jan 1, 1960

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By Samuel A. Rasmussen

Lead anodes are used in commercial copper electrowinning operations, yet there is no method to calculate anode life. To be discussed in this paper are operating characteristics of rolled plate (Pb,Sn,Ca) alloy anodes at Morenci's electrowinning tankhouse along with fundamental operating conditions and how the anode reacts to these conditions. These include anode maintenance, electrolyte temperature and viscosity, cobalt concentration, and manganese concentration. Also to be discussed are anode substrate characteristics under normal operating conditions and how the corrosion rate is affected by changes in operating conditions.

Jan 1, 1995

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By John J. Schanz

The ideal entering freshman for the College of Mineral Industries possesses the necessary aptitude to complete successfully a difficult technical curriculum, has a highly developed intellectual curiosity and adequate preparation in basic mathematics, sciences, and English, is enthusiastic about pursuing a career in the mineral industries, and puts forth a good academic effort while attending Penn State. The present programs of the University?s Division of Counseling and the College of Mineral Industries are directed toward providing the College with students who will meet these requirements. At present, freshmen are admitted to the Pennsylvania State University without entrance examination if they are in the upper two-fifths of their high school classes. All Pennsylvania students in the lower three-fifths are required to take the University Aptitude Test and all out-of-state students the College Entrance Board Examinations. Such students are admitted only if they score sufficiently high on either test to indicate the ability to do satisfactorily the work of University students. Only to this extent, are native intelligence and areas of greatest aptitude known for the Freshman prior to admission, and they are, therefore, largely beyond the control of either the Division of Counseling or the College of Mineral Industries. Because all freshmen, with exceptions that are numerically minor, are required to select a curriculum before admission to Penn State, each student who presents himself for required counseling during the summer, prior to his first semester, has already made a choice of his course of study. In many instances, such choices have been made without a rational and serious consideration of the student?s abilities and interests. Through tests given between the date of admission and the date of the counselling interview, it is possible to measure these characteristics and for the Division of Counselling to advise the student of his chances of success in his chosen curriculum. If he is qualified for the curriculum he has selected, Counselling Service goes on to direct the student?s attention to those other curriculums which are in the same general area as the one he has chosen and which will also challenge his abilities and correspond to his interests, Through this counselling, the curriculums of the College of Mineral Industries, which are often less well known to high school students than others for which they are no more qualified by ability or interest, are brought to the attention of the incoming freshman.

Jan 1, 1959