Search Documents

By VIVEK KASHYAP, PATRICK TAYLOR

The presence of iron in sphalerite induces the formation of zinc ferrite (ZF) during roasting. Zinc refinery residues (ZRR) and electric arc furnace dust (EAFD) contain a significant amount of zinc ferrite and are difficult to treat. According to the literature, up to 71% ZF has been found to be present in ZRR. The dissolution of zinc ferrite is inefficient even in aqua regia. The Waelz process is an existing process to recover zinc from electric arc furnace dust by reduction using carbon monoxide followed by the volatilization of zinc. In this study, zinc was selectively extracted from zinc ferrite by partial reduction of zinc ferrite at relatively low temperature followed by leaching in dilute sulfuric acid (20 g/L). Pure zinc ferrite samples were partially reduced to zinc oxide and magnetite by using H2 gas as a reductant. The presence of magnetite and zinc oxide was confirmed by X-ray diffraction (XRD) technique. A maximum of 95%zinc extraction was achieved after leaching with sulfuric acid on the reacted samples. The paper also discusses the effect of time, temperature, and concentration of H2 in the reducing gas on the extraction of zinc and iron from ZF.

Sep 16, 2020

By Phil Jones

"Dilution — planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a sixmonth period in fiscal year 2018 (FY18) that established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned versus actual toe data. These were rig alignment error, collar location change/ error and in-hole deviation.The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimizer system). The trials were undertaken in the same environment: the Cracow gold mine, an operating underground mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160 percent.The increased accuracy reduced stope dilution by reducing over-break of subgrade ore. The new technology was implemented at Cracow during the latter half of 2018. Despite utilizing the new technology for just six months of the year, the mine recorded a 5 percent overall reduction in dilution for the full year compared to the previous year (FY17); from 22 percent down to 17 percent (a net decrease of 22.7 percent). Mine management attribute a significant proportion of this reduction to the new technology, along with sequencing and planning improvements. This opinion is backed by detailed stope reconciliation data taken during the trial from 28 stopes — representing 20 percent of the total tonnes mined during FY18. The data identified that stopes drilled using the new technology recorded 62.6 percent less average dilution."

May 1, 2019

By S. Deming

Coal is China's main source of energy. In 1988, 76.1% of commercial energy consumption was supplied by coal. To provide a rational utilization of its coal resources, China has paid considerable attention to coal preparation over the last 10 years. In 1980, there were only 105 washeries treating about 100 million tonnes of coal, but by 1988 there were 151 washeries treating 171 million tonnes per year. This paper describes the development of China's coal preparation industry; its growth, the equipment, and the technology. Statistics and information on the current status of the industry are also be presented.

Jan 1, 1991

By William R. Hess

Volcanic ash, although a little-used Kansas resource, is available in forty counties with estimated, reserves of more than 20 million tons. It was first produced in Kansas in the early 1900?s but not until the early 1920 is did it become an important abrasive material. Total production to date is estimated at 2 million tons, the major use being as an abrasive in scouring compounds and soaps, additional uses include ceramic glazes, an additive in cement, and a filler and stabilizer in hot mix asphalt for paving. Unrecorded tonnages have also been used in construction of black-top (macadam) roads. From 1916 through 1944, Kansas ranked first among the states in volcanic ash production; peak production was about 52, 000 tons in 1923. Since 1945, production has steadily declined, primarily because materials other than volcanic ash are now being used for abrasives; only two producers operated in 1964.

Jan 1, 1965

By E. R. Mueller

The natural lives of machines and components vary tremendously! Maintenance managers struggle constantly to maximize their equipment lives while minimizing their maintenance costs, but they normally lack the tools and techniques they need to do this properly. This paper proposes a methodology based on probabilities of failure and expected values for repairs that recognizes the variation among individual machines and components as well as the high costs associated with catastrophic failures. It enables a user to determine the optimum change-out intervals for many types of equipment. The approach proposed here is sophisticated enough to be reliable but simple enough to be applied by the maintenance staff on the shop floor. It will complement existing preventive and predictive maintenance programs.

Jan 1, 1995

By James B. Cathcart

Marine phosphorite deposits occur in Brazil, in the Bambui Group of late Precambrian or Early Cambrian age. The phosphorite is laminated, isoclinally folded, and is composed of black, elongated apatite pellets and quartz grains cemented by quartz and muscovite. Abundant, narrow quartz veinlets cut through the rock at right angles to the elongation direction of the pellets. The phosphorite is 0 to 80 meters thick and contains 5 to 30 percent P205. The deposit is elongate towards the northeast, and the central, thickest, and richest part is bounded by faults. Measured reserves are about 250 million tonnes that average about 13 percent P205. Preliminary testing indicates that grinding, scrubbing, and desliming will produce a material usable for fertilizer manufacture at a cost competitive with imported phosphate fertilizers.

Jan 1, 1977

By N. Wahl, D. M. Blackketter, R. Thornton

This paper evaluated using a water-filled abandoned mine (Orphan Boy) as a heat source for a 240- kW closed-loop heat pump with the goal of heating a 2,000-m2 building. The mine has a 245-m vertical shaft connected to a large stope by three horizontal cross-cut shafts. There is 1,250 x 106 L of water at a consistent temperature of 24-26° C that is available mostly in the stope. The only heat exchanger placement option is in the vertical shaft. Therefore, the focus was to model heat exchanger placement in the vertical shaft to determine the extent to which the systems will induce thermal currents between the stope and vertical shaft. Modeling of thermal currents, temperature profiles and heat contribution from the ground was done using finite difference and computational fluid dynamics. An optimal configuration was determined showing sufficient water movement and heat transfer will occur with a low water temperature in the shaft above 20° C. This project supports a U.S. Department of Energy (DOE) grant that will implement the full-scale system.

Jan 1, 2013

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By N. W. Johnson

The behavior of non-sulphide gangue in chaloopyrite flotation circuits has been investigated. Plant and laboratory tests were carried out on five different ores, and linear relationships were found to exist between the rates of recovery of water and free nonsulphide gangue in the concentrates although there was evidence from pilot plant tests that these were linear approximations to parabolic curves over the limited regions which were observed. There was evidence that the free non-sulphide gangue enters the concentrate by hydraulic classification and a classification function has been proposed to define this behavior. This function is suitable for inclusion in a mathematical model of the process.

Jan 1, 1972

By J. C. Stankus

How to quantitatively identify the loads on a square/arch set is a complicated issue in designing the square/arch set in an intersection/entry. From an engineering perspective, understanding the nature and support mechanism of standing support such as a square/arch set can not only help design the support structure to maintain the roof stability, but save the steel materials and costs of manufacturing, labor, and delivery. Based on the design practices in recent years and successful applications in slope bottom intersections, the authors are confident that the concept of interaction and confinement effect between the steel square/arch set and surrounding rocks is critical in designing a proper steel structure to support an intersection/entry. This paper will detail the design concept and its applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.

Feb 23, 2014

By Edwin B. Wilson

The purpose of the panel's examination of coal mining research and development is to explore how the various groups that make up this research community might work together more efficiently and be more productive. The community, as defined here, includes federal and state governments, coal producers, manufacturers, unions, universities, and industry sponsored research organizations. The framework chosen for these discussions consists of brief presentations by the panel members on their views of the proper role and function of the group they represent. The panel members were also asked to highlight the economic, technical and institutional constraints that affect the performance of research and development and the use of the results. Following these presentations, a number of prepared questions will be discussed by the panel, and audience participation is invited. These questions were given several weeks ago to the panel members for their study. Before proceeding with the panel member reports, a brief review of the importance of R&D to the coal mining industry would be helpful to setting the stage for a constructive dialogue. It is appropriate to begin this review by mentioning that there is complete agreement among the research community that the major goals are: Improve health and safety Protect the environment Increase capital and labor productivity Increase resource recovery Since the basic functions of the academic, industrial and government sectors are different, we should expect that the research and development objectives and priorities, roles and responsibilities under each major goal will be different for each research group. The differences do not represent problem areas. However, problems will arise if the objectives are not properly interfaced at the appropriate time. The consequences of railing to understand the need for integrated programs will be the classic result, best described by the phrase --"a technical success but a commercial failure."

Jan 1, 1978

By A. Fuerst

This paper delivers insights into how high availability combines with high efficiency at the Yanacocha Plant, Newmont Mining Corporation, Peru. Advances in motor design and maintenance with integration of smart control support the approach plant maintenance staff is applying to deliver such excellent results for availability and efficiency in Yanacocha and elsewhere. Detailed efficiency and availability data for 2011 and 2012 in Yanacocha are provided. ABB and Yanacocha teams collaborate closely by combining their experience and continuous development of gearless mill drive procedures and maintenance knowledge to deliver the impressive performance being achieved. The secrets for high performance shared by the Yanacocha maintenance operations point to their systematic, practical adherence to modern asset management and maintenance concepts.

Feb 27, 2013

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982