Search Documents

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

Opencast mines are vulnerable to inclement weather conditions as it disrupts the day-to-day activities at these mines. To address the problem, a perceptive driving assistant system (PDAS) has been developed to increase the visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery (HEMM) at opencast mines in harsh weather conditions.

Apr 1, 2023

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom-designed radial sector sampler , six large blasthole samples were collected to perform the test developed by Pierre Gy to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to total fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32 percent and ±49 percent for copper and molybdenum, respectively. A classical statistical analysis conducted on the data confirmed the level of RSD native to the mine. About 95 percent of the sampling error was produced from one step in the sampling protocol, that of reducing the 1-kg (2.2-lb) sample to a 50-g (0.1-lb) sample for chemical analysis. To minimize the FSE, the use of a slightly different protocol is recommended. The 1-kg sample (2.2-lb) should first be crushed to a 0.2 cm (0.08 in.) particle size. A 250-g (0.5-lb) split should then be taken and finely ground, from which a 50-g (0.1-lb) split should then be taken. These simple steps will reduce the FSE to ±7.9 percent and ±17 percent for copper and molybdenum, respectively. The modified sampling protocol effectively reduces to zero the probability of misclassification of low-grade ore. IntroductionThe Erdenet copper-molybdenumopenpit mine is located in Erdenet in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is 1.5 to 3 km (0.9 to 1.8 miles) wide and about 25 km (16 miles) long (Erdenet Mining Corp., 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 Mt/a (29 million stpy) of ore."

Jan 11, 2017

By Fred Pena

Cyprus Pima Mining Company is located in the Mineral Hill District of southern Arizona, approximately 22 miles south-southeast of Tucson. Cyprus Pima Mining Company is owned 50.01% by Cyprus Mines Corporation, 24.99% by Utah International Incorporated, and 25% by Union Oil Company of California, with Cyprus having the management responsibility. Cyprus Pima's history has been one of continued expansion from an initial plant of 3,000 TPD in 1957; 6,000 TPD in 1963; 18,000 TPD in 1966; 36,000 TPD in 1967; and 53,500 TPD in 1972. The major reason for Expansion IV was that a large volume of low-grade ore had to be moved to get at a higher grade ore in the course of proper pit development. With mining costs already defrayed, this relatively hard, low-grade material became economically profitable for subsequent milling and concentrating treatment. Similar material previously stockpiled was available for ore treatment. In an effort to meet the continuing search for lower unit costs, the largest milling and concentrating equipment had to be examined. The management of Cyprus Pima Mining Company began investigating autogenous, and semi-autogenous milling in 1964 when two carloads of ore selected from the Cyprus Pima pit were sent to the Koppers--Hardinge Operation at York, Pennsylvania for testing. One car contained approximately 40 tons of hard arkosite and the other contained approximately 40 tons of ore classified as soft Hornfels. The purpose of the testing was to determine the amenability of both ore types to autogenous or semi-autogenous grinding.

Jan 1, 1974

By J. A. Cooper, M. R. Petersen, P. O. Jackson, J. C. Langford

The organic, inorganic, and radiological characteristics of airborne aerosols have been measured as a function of particle size in controlled atmosphere test chambers and operating uranium mines. Concentrations of benzo(a)pyrene in two mines ranged from 26 to 57 ng/m3 of air. The carbon chain length of adsorbed n-alkanes was correlated with particle size. Normal mining activities produced an ore dust aerosol with mass median aerodynamic diameter (MMAD) greater than 2 µm. The elements Na, Al, Si, K, Ca, Ti, V, Fe, and U exhibited elemental ratios similar to bulk ore and had comparable MMAD's. The S, Zn, and Pb were higher in aerosols than bulk ore and were associated with smaller MMAD particulates. Radon daughter particle size distributions were influenced by the kinds of particulates

Jan 1, 1981

By D. M. Schubert

As a clean and renewable energy carrier, hydrogen is an important component of most alternative energy portfolios. Hydrogen combines very high energy content by weight with excellent environmental attributes. Since hydrogen reacts with oxygen to produce only water with release of energy, it can be used to power fuel cells, combustion engines, and turbines, without production of greenhouse gases at point of use. However, because of its low volumetric density, storing pure hydrogen is impractical. Thus implementation of hydrogen technologies requires materials that can safely store and release large amounts of hydrogen (1,2). In recent years, the U.S. Department of Energy (DOE) and other governmental agencies around the world sponsored extensive research on hydrogen storage materials, including those based on boron. These efforts have resulted in significant advances in hydrogen storage technologies. Boron materials stand out as leading candidates for hydrogen storage among the many options investigated. Combining excellent hydrogen densities, release rates, and safety characteristics, some boron materials can hold substantially more hydrogen by weight and volume than even pure liquid hydrogen (3-5).

Jan 1, 2010

By J. Paraszczak

Metal mining at great depths presents a number of serious challenges for mine operators. Among them is the high demand for fresh air required to cool down mine openings, evacuate noxious gases and contaminants and provide sufficient amounts of oxygen for miners. At the same time, modern mechanized mines extensively use diesel-powered load-haul-dump (LHD) machines, trucks and other mobile equipment. These vehicles not only emit exhaust gases and diesel particulate matter (DPM), but constitute an additional source of heat. As mine regulations get steadily more stringent with regard to air quality, the use of diesel engines has an additional adverse impact on ventilation costs. In this context, the present paper examines possible alternatives for diesel power trains, both those commercially available and those in development. They are reviewed with regard to their principles, required infrastructure, stage of technology development and progress. The questions of their flexibility, practicality and economic viability are also addressed. Finally, their possible benefits and potential for implementation in the conditions of deep metal mines are discussed. The paper concludes with short- to medium-term predictions concerning promising drive alternatives for vehicles destined to operate in deep metal mines.

Jan 1, 2009

By Robert McIvor

The following is a summary of the Robert H. Richards Lecture on “Learning and Good Fortune on the Road to Discovery” presented at the Mineral & Metallurgical Processing Division (MPD) Awards Plenary Session on Feb. 23, 2026 during the MINEXCHANGE 2026 SME Annual Conference & Expo in Salt Lake City, UT.

Mar 1, 2026

By Constance F. Acton

Based on laboratory structure analyses, a pilot plant investigation was undertaken to evaluate a Michigan conglomerate native copper ore. Comminution or sized feed was accomplished using wet, closed circuit autogenous grinding with and without crushing of the recirculating load. Coarse metallics were concentrated in two stages of jigging with fine metallic copper being recovered in a three-stage xanthate flotation circuit. With a feed averaging 2.09 % Cu, copper recovery ranged from 86-93 % Cu with an average grade of 55.5 % Ca. An evaluation of the processing flowsheet is made in terms of pertinent independent, dependent, and external variables and design factors. Rate equations are developed to describe the grinding and flotation circuits separately as well as the entire circuit as a whole. Performance equations for the overall operation and for the unit operation of autogenous grinding alone are developed in terms of suitable capacity, efficiency and energy consumption terms. Thus, the effects of feed rate, recirculating load and flowsheet design can be rationally evaluated. Energy consumption for various conditions in the pilot plant is compared to the laboratory value. Additionally, size and scale up factors are discussed. Recommendations are made for further studies to be undertaken to further quantify the ore characteristics and the nature of the autogenous grinding operation. However, the feasibilty of beneficiation of this type of native copper ore by means of an autogenous grinding/jigging/flotation circuit is clearly established.

Jan 1, 1977

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By R. J. Hickson

The Grasberg copper-gold deposit was discovered in Spring 1988, just one year prior to the planned closure of Freeport Indonesia's original Ertsberg open pit copper mine. In spite of Grasberg's remote location, 600m above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought their latest open pit mine into production in the last week of 1989, less than two years after discovery. This paper describes the start-up of the operation, highlighting synergies drawn from both the original Ertsberg experiences and the current Freeport Indonesia underground mines.

Jan 1, 1991

By James Corcoran, Richard McLane, Joseph DeMello, Eric Carlson, Hans van de Vrugt

The Los Angeles County Transportation Authority’s Purple Line Extension Phase 1 is a $3.12 billion (USD) design-build, underground heavy rail project, connecting an existing station at Wilshire Boulevard and Western Avenue and extending west 3.92 miles under Wilshire Boulevard and terminating approximately 550 feet west of Wilshire/La Cienega Station. The project alignment runs through the heart of the world famous La Brea Tar Pits and one of the world’s largest urban oil elds. This paper presents a case history of the planning, design, and construction efforts to achieve successful construction of the bored tunnels through Reach 3 of the alignment. Further, this paper outlines the proactive partnership between the owner, Los Angeles County Metro (Metro), the Design Builder, Skanska-Traylor-Shea oint enture (STS), and Southwest Geophysics who provided the geophysical services. Specically, the project included background review of historic site data (e.g., oil eld maps, building foundation plans, historic aerial photographs, etc.), geophysical demonstration testing to ascertain the capability of borehole magnetics to detect oil wells, directional drilling of thousands of feet of horizontal and vertical boreholes, collection of high resolution magnetic gradiometer data along vertically and horizontally cased boreholes as well as the collection of surface magnetometer data, discovery (“ground truthing”) of detected geophysical anomalies, and abatement of potential obstructions within the tunnel alignment.

Jun 23, 2024

By E. M. Frizzell

It is unlikely that improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel cost/shortages, and increasing haul distances as in the past. Therefore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this Bureau of Mines contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic, and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data were gathered from extensive literature searches, European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configurations.

Jan 1, 1979

By Franziska Günther, Helmut Mischo

The calculation of costs for an underground mine, as well as the planning of the equipment and materials to be used, is a complex and time-consuming process. The estimation depends on a multitude of parameters, and all mining processes are interconnected. A novel tool has been developed that enables automated calculation of underground mines and allows for the comparison of the effects of changing individual parameters. Previously, changing individual planning parameters often necessitated a complete recalculation of the mine. The newly developed calculation tool provides an innovative planning aid that allows for more efficient and accurate mine planning and cost estimation. The tool enables the user to implement continuously up-to-data costs and prices. This allows for more accurate planning data and results. The underlying concept of the calculation tool, its implementation at a planned quartz porphyry mine in Germany, and the verification of the tool at an existing underground mine will be presented.

Feb 1, 2025

By L. M. Sandoval, R. Kaunda, C. N. Vasquez, S. C. Falcon

Artisanal and small-scale mining (ASM) involves a wide range of practices, from highly informal and minimally mechanized mining operations with predominantly manual work to formal practices carried out by small but high-tech industrial mining operations [1]. ASM may be a traditional practice, with skills passed from one generation to another. It can be an important driver of local economic development, while simultaneously contributing to a complex array of positive and negative socioeconomic and environmental impacts. There are more than 100 million artisanal and small-scale miners in 80 countries worldwide, and they supply around 20% of the worldwide gold production [2]. According to the Peruvian Ministry of Energy and Mining (MINEM), in 2020, 32% of fatal accidents in formal (legal) Peruvian mining operations were caused by groundfall events [3].The lack of resources, knowledge of best practices in health and safety, and insufficient equipment used in ASM make the probability of suffering work accidents very high. Furthermore, groundfall is one of the main causes of accidents and injuries in underground mines around the world [4], and it is also a concerning problem in ASM, where the associated fatality rate is similarly high. Unfortunately, a proper record of accidents in ASM is not kept, so an estimate of the actual number of groundfall accidents cannot be accurately developed [5]. Currently miners rely on empirical and observational tools acquired through previous experience to assess groundfall risks. The risks for artisanal miners can tend to be significantly greater than risks for those from the mining industry. This is due to the lack of regulation of ASM, which tends to operate outside the legal framework and the regulations lack of enforcement in force for occupational health and safety regulations.

Mar 2, 2022

By Brenton Cook, Nate Long, Larry Applegate, Aaron K. McCain

"The Northgate Link Extension project is the third phase of the Sound Transit master plan to extend light rail throughout the greater Seattle metropolitan area. When completed, the Northgate Link Extension will extend the existing light rail system north by about 7 km (4.3 miles) from the University of Washington to the Northgate neighborhood. A general overview of the project alignment is provided as Fig. 1. The project was funded by a combination of federal grants and allocations from local taxes. The general contractor on the project was JCM Northlink LLC (JCM), a joint venture between Jay Dee Contractors, Frank Coluccio Construction Company and Michels Corp. SoilFreeze, Inc. was retained as a subcontractor to provide ground freezing design and construction services.The project involved the construction of two parallel 5.5-m, 25-cm (18-ft, 10-in.) (inside) diameter tunnels using earth pressure balance (EPB) tunnel boring machines (TBM) and precast segmental concrete tunnel liners. The two tunnels maintained roughly the same elevation along the alignment and were spaced roughly 12 m (40 ft) apart (centerline to centerline). A total of 23 cross-passages connecting the two tunnels were included at approximate 244-m (800-ft) intervals. Cross passage excavations were elliptical in shape with dimensions of approximately 5.6 m (18.5 ft) in height and 5.3 m (17 ft) in width. The cross-passages were 5.8 to 6.1 m (19 to 20 ft) long as measured between the exterior of the tunnels at springline elevation. Cross passages were intentionally located directly beneath public right-of-ways thus avoiding buildings. Many of the cross passages were located beneath narrow roads in residential neighborhoods with mature vegetation, existing utility structures and piping and limited parking areas. Excavation and support for each cross passage was completed using the sequential excavation method (SEM).The subsurface soil and ground water conditions at the cross-passage locations were described in the Northgate Link Geotechnical Baseline Report (GBR) prepared by Jacobs Associates and the Northgate Link Geotechnical Data Report (GDR) prepared by Shannon and Wilson, Inc. Soils along the project alignment were glacially overridden and characterized as very dense or hard. Subsurface soils consisted of cohesionless sand and gravel (CSG), cohesionless silt and fine sand (CSF), cohesive clay and silt (CCS) and till and till-like deposits (TLD)."

Dec 1, 2018

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By R. L. Kloberdanz

Peruvian legislation requires the preparation of an Environmental Impact Study (EIS) for new and expanding mines/beneficiation facilities and the preparation and implementation of an Environmental Adjustment and Management Program (PAMA) to control and mitigate environmental impacts associated with existing mining/beneficiation activities. Shepherd Miller, Inc., developed guidance documents for preparing an EIS and PAMA for Peru's Ministry of Energy and Mines and presented workshops to Peru's mining industry on preparing an EIS and PAMA. This paper discusses the process and approach taken and the results.

Jan 1, 1998

By C. L. Schneider

The problem of predicting the liberation spectra produced by a closed continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population balance model equation. The latest and certainly most significant progress made in this area is the solution proposed by King (1990), which requires one textural parameter that can be measured directly from the ore being studied. The main advantage of King's solution is that it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured, as required by the existing conventional solutions. However, King's solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Milm diagram (Andrews and Mika, 1975). This has never been measured for any ore. The characterization of the internal structure of the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize, monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one-dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1994

By J. P. Wilson, T. Cook, H. Kling

The Tessenderlo-Kerley Leachprocess has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia andammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By L. L. Chasko, D. W. Alexander

Researchers from the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research conducted an assessment of the effects that ground control mesh might have on rock and float coal dust distribution in a coal mine. The increased use of mesh to control roof and rib spall introduces additional elevated surfaces on which rock or coal dust can collect. It is possible to increase the potential for dust explosion propagation if any float coal dust is not adequately inerted. In addition, the mesh may interfere with the collection of representative dust samples when using the pan-and-brush sampling method developed by the U.S. Bureau of Mines and used by the Mine Safety and Health Administration for band sampling. This study estimates the additional coal or rock dust that could accumulate on mesh and develops a means to collect representative dust samples from meshed entries.

Jan 1, 2014