Search Documents

By R. N. Guest

The Tromp distribution curve was used in an evaluation of gravity separators treating a synthetic ore made up of silica and marker minerals of various relative densities. The results pinpoint differences in the concentration of particles of different sizes, and indicate how the grade of a concentrate is likely to vary with particle size. An increase in the feed rate increased the efficiency of the 'waterless' spiral concentrator that was tested, but the multiport spiral concentrator tested was more efficient. Both spiral concentrators were found to be more efficient than the pinched sluice and the shaking table that were tested. The method was found to be a useful way of evaluating gravity concentrators, but, for ease of analysis, care must be taken in the choice of marker minerals.

Jan 1, 1985

By C. Yu, N. Topliffe, H. Song, W. Yu

The water separation pump is a highly effective alternative for medium pressure (1.6?6.4 MPa) slurry pumping requirements and has been widely used in industry since it was invented in the 1980s. The water separation pump is powered by a single or multi-stage clean water centrifugal pump. The water separation pump combines the advantage of high flow centrifugal pumps with the high pressure capability of reciprocating pumps. The clean water pressure is exchanged to slurry kinetic energy through the separating chamber, the principle component of the water diaphragm pump. Currently in its the third generation, the separation chamber uses a ball and flexible water seat that provides a true separation mechanism and can completely isolate the two fluids with near zero water loss.

Jan 1, 2007

Past work on the ignition of methane-air mixtures by coal-cutting picks is reviewed, with special reference to the factors that contribute to ignitions and ways of reducing them. The main conclusions obtained from this review are outlined for the following aspects: mechanisms of ignition, methane concentrations, and the roles of rock types, cutting parameters, cutting tools, and water. However, many of these factors have been investigated on a qualitative, rather than on a quantitative, basis. A considerable amount of effort over a long period has been expended in this area of research. It is shown that a number of the factors influencing ignitions by machine picks have been researched adequately, but that there is still work to be done. Research is continuing in this area, being concentrated primarily upon the ignition potential of the coal-cutting pick.

Jan 1, 1985

By H. M. Wells

The investment decision under uncertainty by H. M. WELLS, Pr. Eng., M.Se. (Fellow) The future outcome of a proposed investment is uncertain at the time the decision must be made to accept it or reject it. This uncertainty can be expressed in the form of a probability distribution. An attempt is made to rationalize the investment decision under these circumstances, especially when the range of possible outcomes extends into both the acceptable and unacceptable domains. A rigorous definition of risk is proposed, and a criterion of risk aversion is developed that forms the boundary between acceptable risk and unacceptable risk (called the loss limitation line). It is shown that this decision criterion can also serve as a quantitative yardstick in the evaluation of various possibilities for 'tailoring' the proposal to mlke it more compatible with the particular financial circumstances of the company concerned.

Jan 4, 1976

The 8th Annual University of Cape Town (UCT)/ University of Stelenbosch (US) Minerals Processing Symposium was held at the Van Riebeeck Hotel in Gordon's Bay on 3rd August, 1990, under the auspices of the Western Cape Branch of The South African Institute of Mining and Metallurgy. The primary object of this meeting was to give research students at UCT and US the opportunity to present their work to a critical audience from industry, and to obtain feedback regarding the research needs of the minerals industry. Although the emphasis of these symposia is on work in progress at US and UCT, they also create an excellent opportunity for informal discussion between academics and metallurgists in industry. The first symposium in this series was held in 1982 at US, while the symposium in 1989 was replaced by the International Colloquium on Developments in Froth Flotation, also held in Gordon's Bay.

Jan 1, 1990

By A. Koursaris, J. B. See

The influence of Iscor coke and Delmas coal on the reduction of Mamatwan manganese ore to ferromanganese was examined by use of a variation of the 'stationary charge in controlled environment' (SCICE) technique. The charges of Mamatwan ore and the appropriate reducing agent were heated to temperatures between 1300 and I600 °C and either allowed to cool immediately the required temperature had been reached or held at that particular temperature for periods of up to ... hours. The heating rate was 350°C per hour, the particle size of the ore was between 2,83 and 12,7 mm, and the particle size of the reducing agent was between 2,83 and 6,35 mm. After being allowed to cool in air, the reacted charges were examined by optical microscopy, X-ray-diffraction analysis, scanning electron microscopy, and electron-microprobe analysis. No significant difference was found between the changes observed during the reduction of Mamatwan manganese ore by Iscor coke and by Delmas coal. A hypothesis is advanced to explain the mechanism of formation of the Fe-Mn-C alloy.

Jan 1, 1979

By J. T. Collins, C. J. Cloete

Secunda Collieries forms part of Sasol Coal, the coal division of the Sasol Group of companies, and already produces 29 Mt of coal per annum from its four collieries: Twistdraai, Brandspruit, Bosjesspruit, and Middelbult. The successful establishment of this mining complex was achieved only through a unique team spirit in which the central services and the decentralized teams under the leadership of the mine management of each of the four mines played an important role. The Secunda mining complex has now reached the optimization phase, during which the mining cost, productivity, safety, and quality of work become as important as production. The setting of priorities and problem solving over the long, medium, and short term are essential for improving the performance of the four collieries. Management had to adapt to the fast-changing environment during the enormously fast build-up of production. The major challenges in the environment were posed by the frequent dolerite intrusions, the extremely hard cutting conditions caused by carbonated nodules and thin sandstone intrusions in the coal seam, and excessive roof and face pressure in some areas due to semi-massive sandstone formations in the rock strata.

Jan 1, 1986

By D. Harbottle, D. Rhodes, T. F. Jones, S. R. Biggs

Multiphase process design and optimization often depends upon the rheological properties of sludges and slurries. In practice the task of determining these important properties is usually carried out by removing small samples from a process line or process unit and performing tests with proprietary bench-top analysers near to site or at a remote laboratory. Sampling will remain an important procedure in industrial processes, but there is also a strong case for augmenting the routine information obtained using an in situ sensor, as suggested below. ?Sampling protocols can result in extensive turnaround periods from sample collection to the generation of results. The delay can have an effect on a variety of factors such as product quality, process operability and efficiency. ?Sampling of toxic or radioactive material can prove an even greater challenge to minimize human involvement. ?Removal often changes the rheology of a specimen, and might lead to incorrect conclusions being drawn about the condition of a sludge. ?Sludge and slurry in a containment suffers a gravitational gradient, so that a removed sample should be paired with its location, particularly in the vertical dimension.

Jan 1, 2007

By D. Rankin, H. J. Stucke, W. K. B. Loftus

Discussion: H. J. Wright (Member): The authors are to be congratulated on presenting such a comprehensive and lucid account of bringing a large diamond mine into efficient production from the grass roots. When one considers the vast amount of planning and hard work that had to be put into the project the authors have done a praiseworthy job in condensing the story, so as to present all the important technical aspects, the logic behind the major decisions and the future thinking on the operations, in a concise and readable form. This was the first experience of De Beers personnel in starting a large diamond mine as an opencast project and nor do they employ a large planning staff, most of the planning being carried out by the executive staff themselves. It is operating most efficiently on a large tonnage and it is neatly and very well laid out. In fact, with its model townships, both for European and Coloured employees, tarred roads, recreation club and its grass golf course, it is like an oasis in the arid climate of the North-Western Cape. The key operation of opencast mining is, of course, the planning of the geometry of the pit. This has been adequately dealt with by the authors. It is of interest to consider some of the consequences arising from complete lack of open pit planning, based on actual operating mines. I refer of course to the present, four producing mines in Kimberley. The Kimberlite pipes were all discovered in a short span of time from the year 1870, onwards. They soon became a hive of activity with diggers industriously working their claims at varying rates. The country rock comprises from the surface downwards, some 90 ft of decomposed dolerite followed by approximately 260 ft of soft Karroo shales, which in turn is underlain by a hard competent Ventersdorp lava, known locally as melaphyre. The average water table was just below the dolerite at a depth of approximately 90 to 100 ft. Only the blue ground was mined leaving the waste rock sides almost vertical, and as the depth increased beyond 100 ft, large falls of sidewall started to take place. The shale was unstable and the falls covered

Jan 3, 1969

By H. C. Voges

The use of heavy-medium separation in the processing of iron ores by H. C. VOGES. B.Sc. (Visitor) The paper discusses various aspects of the application of heavy-medium separation to the processing of hematite ore at Sishen and Thabazimbi. The two main factors to be borne in mind in the design of a plant for such beneficiation are the Iow unit value of the iron ore produced and the high separation densities required. The four factors of importance in the avoidance of high viscosity in the ferrosilicon medium are discussed in turn.

Jan 6, 1975

By D. D. Howat, J. van der Colf

Slags of the system CaO-MgO-AI2O3-TiO2-SiO2at had been reduced in graphite crucibles for selected time Intervals were fully re-oxidized so that an assessment could be made of the rate and extent to which the titanium oxide had been reduced. The derived kinetic parameters were studied as functions of slag composition and temperature. The extent of reduction after selected Intervals of treatment could be correlated with the physical behaviour of the melt (in terms of viscosity and electrical resistivity).

Jan 1, 1979

By P. C. Schutte, N. B. Strydom, A. J. Kielblock

Three groups of unacclimatized men were subjected to five-day climatic-room procedures at wet-bulb temperatures of 29,30, and 31 C respectively. The findings indicated that individuals reach a satisfactory level of heat acclimatization for work in environmental temperature conforming to those at which they were acclimatized. It is, therefore, superfluous to acclimatize men at wet-bulb temperatures that exceed those at which they are destined to work. These methods of acclimatization can be linked advantageously to heat-tolerance testing at mines with suitable underground temperatures.

Jan 1, 1983

By A. V. Z. Brink, D. M. O’Connor

Recent research into the prediction of mining-induced seismic events by the monitoring of small microseismic events at Western Deep levels Gold Mine is described. Measurement and interpretation techniques and results are presented. It was found that the occurrence of the larger events near longwall faces on the Carbon leader reef is preceded for some hours by an increased rate of microseismic emission and spatial concentration of the microseismic events in the zone of eventual failure. The research is currently being expanded with the aim of producing a practical rockburst early-warning system.

Jan 1, 1983

By C. J. Van Niekerk, C. C. Begley

SYNOPSIS The paper opens with brief descriptions of the history, occurrence, and regional geology of South Afri¬can zinc deposits, and follows with descriptions of the resources, mining methods, and processes for the concentration of the sulphide minerals and the extraction of zinc as practised in South Africa. The end uses in the form of alloys or as salts are given in some detail. Statistics on the production and consumption of zinc in South Africa are given, and the current market situation and future prospects are discussed briefly.

Jan 1, 1991

By M. J. Nicol, P. Balestra, E. Schalch

A detailed fundamental study has been made of the various factors that influence the partial reactions comprising the electrochemical model of the cementation of gold from cyanide solutions by zinc. The effects of cyanide concentration, pH, agitation, additions of lead, and the presence of various impurity ions on both the anodic dissolution of zinc and the cathodic reduction of gold have been investigated. The results are used to explain the influence of these variables on the rate of cementation, and possible implications of this work for plant practice are discussed.

Jan 1, 1979

By L. Dison, J. A. Hahn, G. E. Blight

A system of artificial support for shallow mines is described, analysed, and evaluated. The system can be designed rationally to support a predetermined overburden load, and tests have shown that the design theory gives accurate predictions of strength. The support system, consisting as it does of two basic materials, reinforced granular material and reinforced cemented material, is flexible and can be varied to suit changing requirements of height and load. The system of preloading to the design load by jacking off the roof ensures that the walls are both stiff and prooftested.

Jan 1, 1982

By G. J. Kringe

The results of a series of measurements of accelerations and guide-roller loads made on mineshaft conveyances are given, together with the predictions of these accelerations and loads based on a computer programme. The analysis of the measurements is described, and the results of the measurements and computer predictions when compared show reasonable agreement. Some parameters that increase the guide-roller loads are identified, and their effects are studied, together with some comments on the total loads. Finally, a possible format for a design specification is discussed, and some tentative design values are given.

Jan 1, 1986

By G. H. Grange

The control of dust from mine dumps by G. H. GRANGE Pr. Eng., B.Sc. (Min. Eng.) (Rand) (Fellow) This paper gives a resume of the early attempts to control dust from mine dumps, leading up to the research project undertaken by the Chamber of Mines ResearchLaboratories to explore the possibilities of establishing vegetation on dump surfaces. The ultimate success of this work and details of the principles involved are outlined. Also given are a brief history of the event that culminated in the introduction of the Atmospheric Pollution Prevention Act in 1965, details of the control of dust in terms of this Act, and a short summary of the dust-control work.

Jan 3, 1973

By Penswick D.

From the perspective of management control, most mining operations can be represented by a hierarchy comprising four layers. The base of this hierarchy consists of the individual pieces of equipment that are used to break and transport rock. The next level comprises the coordinated interaction between different pieces of equipment, termed a process. An operation results from the bringing together of different processes within a common discipline, such as mining or hydrometallurgy. Finally, an enterprise is formed when the separate mining, concentrating and smelting business units are combined. To date, much of the literature written on the topic of mining automation has focused on the equipment level, specifically on removing the operator from production mining equipment. This focus should not, however, overshadow advances registered in automation at both the process and enterprise levels. Only at the operations level of the hierarchy has little progress been made. While automated equipment, process management and enterprise resource planning are a current reality; it is argued that the benefits from automation have, to date, been largely elusive. It is further argued that full benefits of automating other levels will only be fully achieved when this ‘gap’ in the mining automation hierarchy has been addressed and an uninterrupted, process-wide information flow across the entire operation is achieved. Furthermore, it will be reasoned that so-called vertical integration can only be achieved with an automated operational level in place. It is believed that all the necessary building blocks are in place and that the industry is ready for this development. The paper concludes by presenting a vision for what operational level automation would achieve.

Sep 1, 2001

To B. K. Martus I discussed several points raised by Mr Martus in my reply to Professor Krige*. Mr Martus discusses several possible interpretations of optimum South African sales, but in my paper these sales refer to the sales level that maximized the working profit of the whole South African gold-mining industry over the past eleven years. Mr Martus also seems to be under the impression that the paper deals with the future. While there may be references to the future, and some implications for the future may be obvious, the paper deals essentially with the past eleven years.

Jan 1, 1984