Search Documents

By M. S. Moholwa, J. D. Steenkamp, H. L. Rutto

Manganese ores are the major source of manganese for the production of manganese ferroalloys. There is a gap in the knowledge of the decrepitation behaviour of manganese ores, which presents a problem in the operation of smelters. Decrepitation, which is the breakage of the ore particles upon heating, is an important quality parameter for these ores. The purpose of this investigation was to determine the extent to which South African manganese ores decrepitate during preheating in a rotary kiln. The effects of temperature, rotational speed, and particle size decrepitation were investigated. Manganese ores were heated in a laboratory-scale rotary kiln at temperatures of 600, 800, and 1000°C, and rotational speeds of 3, 6, and 12 r/min. The size ranges were +6-20, +20-40, and +40-75 mm and the residence time was constant at 30 minutes. The decrepitation index (DI) is quantified as the ratio of the mass of <6 mm particles after pre-heating to the total mass of the sample. It was found that the DIs for all ores used were proportional to the temperature and the rotational speed and inversely proportional to the particle size range with temperature being the most important parameter. Ore A was the most susceptible to decrepitation followed by ore C and ore B; this was mainly to the decomposition of kutnohorite, the content of which was the highest in ore A and the lowest in ore B.

Nov 30, 2022

By R. Letsaole, H. Mabowa, J. Sehat, J. Tshilongo, T. Rampfumedzi, N. Ntsasa, A. Mkhohlakal1

This study explores the use of co-collectors to enhance the recovery and determination of rhodium during fire assay with lead collection, followed by acid dissolution using conventional hot plate methods. Rhodium, a critical platinum group metal, poses analytical challenges due to its low natural abundance and complex chemistry. Among the co-collectors tested, palladium and tellurium demonstrated significantly improved rhodium recoveries, ranging between 100% and 120%, whereas silver resulted in poor recovery and higher error margins. These findings highlight that co-collectors can enhance the efficiency and sensitivity of platinum group metal analysis, although their effectiveness is dependent on the chemical interaction with the target element. Acid dissolution was essential to ensure complete digestion of prills prior to analysis, enabling accurate quantification of rhodium. Overall, the findings suggest that palladium and tellurium are effective co-collectors for rhodium determination in fire assay, while silver and lead flux alone are unsuitable. This work provides important insight into optimising fire assay procedures for reliable rhodium analysis, with potential benefits for platinum group metals recovery and economic evaluation.

Mar 6, 2026

By G. Pienaar

The South African Institute of Mining and Metallurgy held a Colloquium on High-strength Low-alloy Steels on 27th October, 1983, at the Vaal Triangle Technikon, Vanderbijlpark. The Colloquium was attended by some 170 delegates.

Jan 1, 1984

By S. Blancher, A. Perroton, H Smith, T. Nzima, T. Wallmach, V. Dieudonné

Chromite beneficiation is generally performed by crushing and density separation using spirals. At the Dwarsrivier Chrome mine spiral efficiencies seam to vary, the reason for which is not evident. This sometimes results in the production of low-grade products, which are sold at relatively low prices. This paper represents a Qemscan® study that investigated mineralogical reasons for these variations. Variations in liberation of chromite particles as well as variations in chromite compositions were investigated. The results showed that the so-called low grade chromite product can be improved to become a high grade chromite product by means of a refinement in mineral processing. A detailed Qemscan® database (SIP file) was developed to account for variations in chromite chemistries. It can be shown that chemical variations with respect to Cr, Al, Mg and Fe in chromite particles reporting to the scavenger tails are larger than in the high grade product. A combination of these chemical variations together with a decrease in liberation of chromite particles in the scavenger tails can potentially help to recover more chromite particles from this specific process stream.

Sep 1, 2021

By DeVerle P. Harris, David E. Euresty

"Potential metal supply refers to metals to be produced from as yet unknown deposits. Naturally, to measure potential supply requires, among other things, inference to the number of deposits, their tonnage, and their grade Thus, probability distributions were constructed for each 400-square mile cell in Northern Sonora, Mexico. A computer system was developed that simulated the occurrence of deposits for each cell, exploration for the deposits, and their exploitation. Evaluation was performed for each deposit by discounted cash flow analysis.An objective of this study was to explore the effect of the transportation network and required road or railroad construction upon potential supply. Consequently, the evaluation system was designed to consider the spatial location of a simulated deposit to the existing transportation network and the market destination. The construction of linkages to connect the deposit to existing transportation arteries as well as the carrying of the concentrates to the intended market were simulated. in terms of cost. The selection of the path took into account the existing terrain. This was done by digitizing topographical maps and representing the topography of the area by an orthogonal grid of elevations. The optimum route was selected by dynamic programming, meeting a prescribed gradient constraint. The potential supply of each cell was determined, allowing for the infrastructure effect."

Jan 1, 2014

By C. Birch, J. Perold

"Due to the challenging geological environment of the Postmasburg Manganese Field (PMF), a study was conducted to determine if any benefits would derive from the inclusion of resistivity data during threedimensional (3D) modelling of the manganese resource. This was achieved by estimating manganese resources from 2011/2012 drilling data and comparing them with manganese resources estimated from the same drilling data and resistivity data collected during 2013 and 2017.Both models were adjusted to limit their extent to the same 3D modelling space. Significant volume and tonnage differences were observed for all lithological units. The greatest differences were noted in the manganiferous zones of alteration – 7.200 Mt for the geological model versus 3.700 Mt for the geoelectric model.This study showed that the inclusion of resistivity data can reduce exploration costs significantly, as a direct consequence of the resistivity data allowing more accurate siting of boreholes. This decreases the number of boreholes, samples, and analyses required due to the 3D electrical delineation of mineralized areas prior to drilling.An additional benefit is the ability to more correctly forecast the net present value of an operation due to more accurate estimation of manganese resources and stripping ratios. This is clearly demonstrated by the estimated gross profit estimation of R409 million for the geological resource model versus R264 million for the geoelectric resource model.The addition of resistivity data can, therefore, reduce exploration costs and can increase confidence in geological and financial modelling. It would be reasonable to conclude that this approach could also be used for karsthosted massive sulphide deposits. IntroductionAccording to Corathers (2014) and Gajigo, Mutambatsere. and Adjei (2011), South Africa holds between 75–80% of global manganese reserves, followed by Ukraine (10%), Australia (3%), India (3%), and Gabon (2%). The known, land-based, manganese resources located elsewhere are estimated at 2%.The majority of economically important sedimentary manganese ore deposits in South Africa are situated in the Northern Cape Province (Gutzmer, 1996). Manganese ores of the Postmasburg Manganese Field (PMF) were discovered in 1922, and the Kalahari Manganese Field (KMF) in 1940. According to Astrup and Tsikos (1998) and Gutzmer (1996), mining of manganese ore from the PMF ceased during 1989 in favour of the superior quality of manganese ore from the KMF."

Mar 1, 2019

By A. Y. Senchenkoa, Y. V. Kulikov

The relationships revealed between ore hardness and specific energy consumed by crushing and grinding are described in the paper. A comparison of key technical and economical parameters of SAG and HPGR circuits is made, based on testing of several ore types for greenfield projects. The comparison of results make it possible to estimate efficiency of the technologies application, depending on ore hardness and taking into account potential risks for a circuit under design. Keywords: Comminution circuits, SAG, HPGR, test results

Jan 1, 2020

By K. Woodward, Y. Potvin, B. McFadyen, M. Grenon

Open stoping has become a popular mining method in hard rock mines, not only due to the safety of the method as a non-entry approach, but also because of the high extraction rate and low costs. At mine sites, stope performance is evaluated by calculating stope overbreak using the stability chart. However, limitations of the stability chart regarding the precision of the predictions, nonconsideration of factors such as the influence of blasting, and the exclusion of underbreak have led to non-optimal designs. The capabilities of today's computers have increased the amount of data being collected and the power of models being built. This article presents a step towards a new stope design approach where stope overbreak and underbreak are measured and georeferenced using octrees at an approximately cubic metre resolution and predicted using multivariate statistical models (partial least square, linear discriminant analysis, and random forest). Results show that overbreak and underbreak location along the design surface and their magnitude are predicted with good precision using a random forest model. These predictions are used to build the expected geometry of the open stope. The resolution of the data and the use of multivariate analysis has enabled the prediction of variation in stope performance along the design surface, going well beyond the simple qualitative per stope face prediction provided by a traditional stability chart approach.

Jun 5, 2023

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

By Xiang-nan Zhu, Hao Zhang, Lin Li, Jun Qiu, Yue-xian Yu, Chun-chen Nie, Xian-jun Lyua

Waste printed circuit boards (WPCBs) are excellent metal resources. Mineralogical characteristics of different components in WPCBs were analysed in this study. Organic-enriched particles, fibreglass-enriched particles, associated particles and metal-enriched particles were obtained by density gradient method. Subsequently, the elemental composition, morphology, dissociation characteristics, functional group composition and phase composition of different components were analysed by X-ray fluorescence spectrometer (XRF), scanning electron microscopy and energy dispersive spectrometer (SEM+EDS), infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). Elemental analysis results show that Cu is mainly contained in metal-enriched particles. SEM+EDS analysis results demonstrate that ideal dissociation can be achieved when the WPCBs are broken to -1 mm. Organic matter particles are enriched with carbon and oxygen elements, while fibreglass particles and associated particles mainly contain Al and Si elements, verified by XRD analysis. FT-IR results show that hydrophilic and hydrophobic groups exist widely in all components, caused by widespread organic matter. This study reveals the important properties of different components in WPCBs, which is of great significance for the subsequent separation process. Key words: Waste printed circuit boards, mineralogical analysis, elemental composition, dissociation; phase analysis, functional group composition

Jan 1, 2020

By F. Mwaura

"The aim of the audit was to determine whether the mining project environmental impact assessments (EIAs) in Kenya are undertaken according to international best practice. A sample of 50 EIA reports for the 2007–2016 period was evaluated using 18 criteria in the Environmental Law Alliance Worldwide (ELAW) guidelines. The findings showed that only two criteria were considered ‘excellent’ according to the ELAW guidelines, namely baseline environmental assessment and prediction of physical impacts. Six criteria were found to be ‘satisfactory’, including prediction of social impacts, analysis of alternative options, and impact mitigation. The reports were quite weak in terms of: consideration of all phases in the mining cycle, environmental regulatory framework, prediction of biological impacts, stakeholder consultation and engagement, integration of human right issues, and integration of climate change and cost-benefit analysis. It is therefore recommended that the Kenyan National Environment Management Authority (NEMA) should consider tightening the EIA terms and conditions in the approval of statutory terms of reference (ToR) for full-scale mining EIAs to ensure improved performance of EIA as a tool for environmental protection. IntroductionThe nexus between society and the environment has continued to generate interest because the environment is the source of goods and services that sustain the various needs of human beings as outlined in the UN sustainable development goals (SDGs) (Armstrong and Peart, 2000; Sutton 2004; Chakrabarti 2007; Strange and Bayley 2008). All the five generic categories of societal needs, namely physiological needs (food, water, clothing, medicines, etc.), residential and occupational needs (shelter, transport, energy, etc.), economic needs (tradeable goods and services), leisure and recreational needs (tourism), and cultural and spiritual needs (e.g. sacred resources and ecosystems) (Mwaura et al. 2016) are addressed by the environment. Consequently, a wide range of development sectors have been established around the world in order to address the above needs (Lederer, Galtung, and Antal, 1980; Rammelsberg et al., 2006; Noonan, 2014). All these development sectors rely entirely on the environment for their proper functioning, as shown in Table I."

May 1, 2019

By L. A. Cisternas, R. I. Jeldres, D. Calisaya

"Flotation of copper-molybdenum sulphide ores in seawater entails critical challenges such as selective recovery of molybdenite, effective pyrite depression, and reducing the lime addition required to reach highly alkaline conditions. It is essential that laboratory flotation tests aimed at solving these problems give reliable, reproducible results and indicate the correct approach for industrial operations. Rougher flotation of coppermolybdenum sulphide ores in seawater was investigated using two different cells: a modified Denver cell and a standard commercial cell. The effect of an organic reagent on the flotation performance was tested, and the fast/slow-floating model was used to describe the results. The modified Denver cell significantly improved the reproducibility of the flotation test results, due to technological enhancements such as the impeller being driven from below without a stator, which enables the whole froth surface to be scraped with a paddle at a constant depth and rate. Organic reagents are a promising alternative to inorganic reagents for depressing pyrite in seawater. However, further studies should be conducted to investigate their impact on molybdenite recovery, as well as to evaluate the possibility of depressing pyrite after molybdenite separation. The fast/slow-floating model was found to be appropriate for describing the flotation kinetics of the copper-molybdenum ores. The parameters are useful for comparing the performance at different conditions. IntroductionOwing to the increasing scarcity of fresh water, the use of seawater mining and mineral processing is becoming increasingly important (Cisternas and Moreno, 2014). Seawater can be desalinated by reverse osmosis, but this involves considerable costs, limiting it to the big mining companies (Akgul et al., 2008; Leidner et al., 2012; Ghaffour, Missimer, and Amy, 2013). Furthermore, desalination has environmental consequences (Lee, Arnot, and Mattia, 2011); for example, a desalination plant designed to process 2.5 m3/s requires an electrical energy supply of around 30 MJ/s. To supply this power demand, a thermoelectric plant burning bituminous/sub-bituminous coal mixtures at a thermal power generation efficiency of 35% might release around 1200– 1500 t of CO2 per day. Furthermore, the effluents from desalination plants are typically discharged into the sea, and their high temperature and ionic content inevitably modifies the marine environment, with unknown consequences. The direct use of seawater is, therefore, more attractive, but it also poses major challenges since seawater contains ions that adversely affect mineral recoveries. In particular, in the flotation of sulphide ores in seawater, the floatability of molybdenite is depressed (Castro, 2012; Laskowski, Castro, and Ramos, 2014)."

Jan 1, 2017

By M. -A. de Ville d’Avray, J. Bosman, S. Brochot

Dense Medium Separation (DMS) technologies are used for light (coal, lithium) or heavy (chromite, iron ore, diamonds) minerals concentration, but also for ore pre-concentration (Pb/Zn) or waste (plastics). Dense media are mainly formed from a suspension of magnetite or ferrosilicon in water. Such DMS circuit design or optimisation requires a full and detailed material balance which can be obtained by the aid of modelling and simulation tools. This balance is not limited to ore and its valuable minerals, but also the recovery of the dense medium itself. If the density is the main property used for separation, the particle size plays a non-negligible role, and, more precisely, the liberation classes which can be associated to the washability curve. The paper presents how the modelling and simulation platform USIM PAC can answer this challenge with the set of models for DMS operating units such as drums or cyclones, and their associated screens (drainage, rinsing) and magnetic separators for medium recovery. Some examples for mineral concentration will illustrate this approach. Keywords: Process simulation, process modelling, dense medium separation, process optimisation

Jan 1, 2020

By T. P. Letsebe, L. Magwaza, T. A. Sethu, S. M. Rupprecht

"The authors were tasked with introducing safe and efficient drilling and blasting practices to a small artisanal mine located in the Eastern Province of Rwanda. The current mining methods employed at the mine are inefficient as rockbreaking is conducted utilizing hammer and chisel, or by drilling and blasting with no understanding of the rockbreaking process. The paper discusses the drill and blast cycle, as well as the associated activities necessary to support the mining cycle. The challenges and critical aspects in implementing drill and blast activities are discussed, as well as some of the technical aspects, i.e.drilling pattern, initiation and timing of the blast, and handling of misfires. Ancillary issues such as ventilation, training, communication, effective planning, logistics, and human relations are also examined. IntroductionRockbreaking accounts for 60% of the direct mining costs in small-scale mining. When drilling and blasting practices are poorly implemented the process becomes inefficient and dangerous. The introduction of a proven drill and blast system to artisanal mining offers a number of challenges, with safety being considered the backbone of any sustainable operation and a standard that cannot be compromised.The paper is based on a project at an artisanal cassiterite (tin) mining operation in a small village in the Kayonza District in the Eastern Province of Rwanda. A drill and blast programme utilizing industry best practice was introduced at an underground development end; a raise developed at an inclination of 23 degrees. The underground working is accessed via a 17 degree incline shaft with an operating length of 105 m and serviced by a single drum winder. The winder operates at a speed of about 3.5 m/min hoisting two 1 t wagons from the bottom of the incline to surface for tipping (Figure 1)."

Jan 1, 2017

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By S. W. Jacobsz, Y. Narainsamy

Several high-impact tailings dam failures around the world in recent years have placed a renewed focus on the stability of tailings dams and pointed to potential shortcomings in traditional drained design and safety evaluation procedures. A need to consider undrained shear strength in the design of tailings facilities has become apparent. However, there are specific requirements that need to be met before undrained shearing occurs. In South Africa, the last major failure was likely the Merriespruit disaster in 1994, which leads to the question of whether the conditions required for undrained shearing are readily applicable to South African tailings dams. This paper describes research at the University of Pretoria that has recently commenced to further investigate the conditions required for undrained failure to occur. The research includes laboratory and field testing to replicate these conditions in the laboratory and relate them to those found in an active tailings dam.

Jun 2, 2022

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

By J. K. Pothal, S. Basu, R. Barik, P. K. Senapati, A. Dubey

The aim of this paper is to study the characteristics of limestone particles (size varies from 4 mm to 20 mm) during its transportation from open cast mines through pipes. The influence of four different size fractions of limestone samples (4–6 mm, 6–10 mm, 10–15 mm, and 15–20 mm) on pipe flow characteristics during vertical transport in a 100 mm NB hose pipe was investigated. The flow velocities in the vertically lifting pipe was varied from 0.95 m/s to 2.78 m/s and a rotary feeder of 2 to 4 tonne/hr. capacity was employed to feed the limestone samples to the lifting pipe. The pressure drop data for the different size fractions of limestone samples at different mixture velocities were analysed. The effect of input volume fraction and superficial velocity of limestone samples on hold-up ratio were discussed. It was indicated that there was no substantial increase in pressure drop of slurry samples in the studied range of concentrations (CW = 4.22% - 12.54%), particle size, and low to medium range mixture velocities with respect to water run head loss data. The hold-up for the larger size fractions (15–20 mm) of limestone samples was found to be significant as compared to smaller size fractions, which may be due to terminal settling velocities of individual fractions of the studied samples.

Mar 4, 2025

By J. E. Xu, J. Y. Zhang, M. Q. Sheng, K. Wan

"SynopsisThe densities of selected CaO-Al2O3-MgO slag systems were measured at 1823K by the Archimedean method. Thirteen different slag compositions were chosen based on different levels of the MgO content and the mass ratio of CaO/Al2O3. The results indicated that the density of the slag decreases with increasing MgO content (from 0–3.78 mass%), but increases with further increases in MgO content up to 11.33 mass%. At a fixed MgO content of 5.5%, the trend of density change with CaO/Al2O3 in the slag is similar to that for changes in MgO content. On the basis of the regular solution approximation rules of excess molar quantities, an attempt was made to estimate the molar volume of the slags investigated. The application of the molar volume model confirmed that the present expanded approximation rules are applicable to predict the molar volumes of the melts discussed.IntroductionDensity is one of the most important fundamental properties of slags, which influences metallurgicaly phenomena in many ways. Density is sensitive to the nature of the chemical bonds and the species in the melt, and is of great importance not only for theoretical research on the structural properties of molten slags, but also for industrial applications. Density is also required to estimate other key properties used to assess the behaviour of high-temperature molten oxides, e.g. viscosity, surface tension, and thermal conductivity.Liquid calcium aluminate slags that contain magnesia are the basis of most ladle slags for secondary refining processes. The CaO-Al2O3 binary phase diagram (Hallstedt , 1990) shows the eutectic composition (50 wt% CaO and wt% Al2O3) has the lowest melting temperature. The main emphasis of this study is on the 12CaO·7Al2O3 refining slag with MgO additions. The CaO-Al2O3-MgO ternary system is of considerable importance in industrial metallurgical processes, and is fundamental to the understanding of metallurgical slags, ceramic materials, and geological phenomena."

Jan 1, 2015

By B. McFadzean, N. Patterson, M. Becker, S. Geldenhuys

The retreatment of secondary tailings for platinum group metals recovery presents a range of potential challenges, which vary depending on the nature of the original ore and the type of pretreatment it was subjected to. These challenges include the prevalence of ultrafine particles, which promote slimes coatings on valuable minerals, hinder bubble-particle attachment, increase pulp viscosity, and lead to higher gangue entrainment; surface oxidation of minerals, which alters their floatability; and the presence of deleterious gangue minerals and residual platinum group metal species that are inherently difficult to recover by flotation. This study compares the batch flotation performance across a range of tailings samples from the eastern and western limbs of the Bushveld Complex. A complementary mineralogical analysis was conducted to gain deeper insights into mineral behaviour. The paper evaluates these findings to identify the key factors contributing to poor platinum group metal performance.

Mar 6, 2026