Search Documents

By Eliot J. White

The Bureau of Mines tested cores from 35 wells from 14 oil-producing zones in southern Illinois, southern Indiana, and western Kentucky to determine why rates of water injection were apparently low in some zones. Since these zones contain only minor amounts of clay minerals, it is concluded that permeability reduction results from movement of dislodged silica particles and other material, including the clays, that lines the pores. Both single-phase and two-phase permeability measurements, however, indicated that most samples had only low to moderate water sensitivity, so that permeability reduction due to such particle movement should usually not be of practical significance. The effective permeability to water was considerably lower than the effective permeability to oil during two-phase flow measurements, as is typical of most reservoir rocks. It can be concluded, therefore, that relatively high injection pressures will be required in waterflooding thin zones or zones having low permeabilities.

Jan 1, 1966

By F. S. Wartman

Recent changes in metallurgical practice, particularly those in flotation, have altered greatly the functions of the different units of a copper smelter. Gangue minerals are removed from the feed so much more thoroughly that the reverberatory furnace, once virtually a concentrator in which a low-grade ore was concentrated into a rich matte by virtue of the removal of gangue elements as slag, has become very largely a melting furnace in which the rich flotation concentrates are rendered molten so that they may be converted. Moreover, since the proportion of matte to slag in the reverberatory furnace output is greater than it was formerly, the amount of converter slag returned to the reverberatory for cleaning is, in comparison to the amount of slag actually formed in that furnace, also much larger. In some cases, approximately half of the reverberatory dump slag may have originated in the converter. The increase in the proportion of convertor slag to total slag produced has brought about certain consequences not entirely desirable. Converter slags contain a high percentage of iron and therefore are high in specific gravity and are very basic. A considerable guantity of magnetite, both dissolved and suspended as solid crystals, is always a component, The basic nature of the ordinary converter slag and the presence of the suspended magnetite crystals make impossible the reduction of the copper content of the slag below approximately 1 per cent by even the most prelonged settling, and a re-treating process is necessary. At present, general practice in western copper smelters is to return the converter slag molten to the reverberatory furnace. Here dilution by mixing, with slag formed in the reverberatory furnace and reaction with raw sulphides and siliceous materials in the reverberatory feed reduce the magnetite and increase the silicates to the point necessary for a satisfactory dump slag.

Jan 1, 1930

By Robert G. Lundquist

This report summarizes all relevant findings and conclusions regarding capabillty of high-energy projectile impact to operate effectively in an open pit mining environment and to successfully handle secondary breakage and bench scaling problems. A silenced, aimable, mobile projectile launcher was designed and fabricated, utilizing a Government-furnished smooth-bore, 90 mm cannon. The silenced launcher was tested at the contractor's test site prior to shipment to ANAMAX Mining Company's Twin Buttes Mine near Tucson, Arizona. Demonstration tests were conducted at an inactive waste dump in the mine on 39 oversize boulders to determine the relationship between boulder size and projectile energy required for secondary breakage. The high energy projectile impact method (known by the acronym REAM -Rapid Excavation and Mining) was tested on an additional 23 boulders in the working mine and on 31 areas of potentially loose rock high on the pit walls. Most of the secondary breakage tests were successful and acceptable for open-pit mining purposes without producing large amounts of fly rock. Five of the 31 scaling tests were successful with one shot, but most of the remainder required two or more shots, and a few could not be dislodged because they were not as loose as they appeared to be, based on visual examination from a distance. Cost comparisons between the REAM method and conventional methods of secondary breakage and bench scaling are discussed. A film documentary, REAM--Mining Applications of High Energy Projectile Impact, has been produced by the contractor depicting the applications of the silenced cannon.

Jan 1, 1976

By Foster Fraas

The Bureau of Mines investigated a method for calculating values of adsorption energy; the goal was to devise an equation consistent with experimental data accumulated in the investigation of adsorption as related to ore separation processes. Numerical identification of the constants of a previously formulated equation provided an equation by which values of adsorption energy could be calculated. Values thus calculated checked with those obtained by calorimetric measurement.

Jan 1, 1965

By K. A. Fowler, L. W. Higley

The effect of uranium on the transformation kinetics and the hardenability of a low- alloy steel was evaluated . Isothermal transformation curves were developed from metallographic studies , and hardenability was determined by standard Jominy end- quench tests . For the steels investigated , the addition of 0.15 weight- percent uranium was found to produce a significant shift in the isothermal transformation curve and caused a related increase in hardenability . These effects diminished rapidly when the uranium content was increased above 0.2 weight - percent .

Jan 1, 1964

By K. K. Kershner

Sulfide ore concentrates containing cobalt, nickel, copper, lead, and iron were salt roasted and leached on a laboratory scale. More than 95 percent of the cobalt, nickel, and copper was recovered. Heating patterns for salt roasting different concentrates were established. More cobalt, nickel, and copper were recovered from a bulk concentrate composed of a mixture of copper concentrate and iron concentrate. This mixture corresponded roughly with the mixture of these materials in stockpiles in southeastern Missouri. A temperature range of 375° to 400° C. was best for salt roasting. Metal chlorides were leached at a pH of 1 from chloridized charges of concentrates, Although the amounts of cobalt, nickel, and copper extracted were high, the amount of iron dissolved simultaneously interfered with subsequent separation and recovery of these metals. The amount of dissolved iron was reduced substantially by steam treating chloridized charges of bulk concentrate at 300° C. In this way, the ratios of cobalt, nickel, and copper to iron in leach liquors permitted satisfactory separation and recovery of these metals. INTRODUCTION The Federal Bureau of Mines is experimenting with chloridizing reactions.4 5 6 7/ Salt roasting of sulfide ores and concentrates, or their calcines, to form metal chlorides has certain advantages. Chlorides of

Jan 1, 1961

By A. C. Rice

Aminopolyacetic acid chelating agents were added to separatory-funnel-scale solvent-extraction systems to determine the effect on separating rare-earth elements. Average values for separation factors between adjacent elements obtained with Primene JM-T2 increase 36 percent when EDTA is added to the aqueous phase. Adding HEDTA or DCTA also improves separation factors for certain rare-earth elements. Percentage of extraction and the separation factors exhibit marked sensitivity to concentrations of amine, chelating agent, and hydrogen ion. The chelating agents improved separation in Primene JM-T, BHDA, and Primene 81-R extraction systems.

Jan 1, 1963

By N. E. Hanna

[Testing explosives for safe use in coal miner ran boon an important factor in preventing mine explosions. In the United States, explosives that have been approved by the Bureau of Mines are called permissible explosives. A purvey of the history of coal mining since permissibility testing welt, instituted some 4 years ago shown that there is no record of a coal-mime explosion caused by permissible explosives when used in a manner prescribed by the Bureau. To maintain the appropriate standards of quality, the Bureau of Mines conducts a series of examinations and tenth on samples of explosives collected in the field. In what is considered the most crucial test, teat 1, the explosives An fired from a steel cannon into a gallery atmosphere containing a mixture of natural gas and air, In another important test, test 4, the explosives charge to fired into a mixture of natural gas, air, and coal diet. To satisfy the permissibility requirements, the explosive must undergo throe gallery teats without igniting gas or coal duet. Other tests also are required for permissibility, but they do not come within the scope of the present paper, which studies the factors affecting the incendivity of explosives when fired into methane, air, and/or coal-dust mixtures. It in believed that a better understanding of the factors will contribute to the development of safer explosives.]

Jan 1, 1954

By D. W. Frommer

As one phase of a general problem of recovering sulfide slimes, mineral-dressing research was conducted on flotation tailing from the St. Joseph Lead Co., Bonne Terre, Mo., mill to recover a significant portion of the residual, finely divided galena. Production of a high-grade concentrate was not part of the immediate objective. Only a reasonable ratio of concentration of lead sulfide slime was sought, since the problem of upgrading by mechanical or extractive processes would be considered in the later stages of this study. The results show that, from a feed material averaging 0.20 percent lead (about 70 percent finer than 400-mesh), a recovery of up to 45 percent could be effected by flotation in rougher concentrate analyzing up to 6.5 percent Pb. These results were obtained by using larger quantities of various xanthates and sodium sulfide than used customarily in mills. Sodium sulfide, which is ordinarily detrimental to flotation of galena, was beneficial in this case.

Jan 1, 1959

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the 'indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By M. H. Chetrick

An important factor in the design and operation of a lignite-gasification plant is knowledge of the thermal requirements. These not only vary with different-size plants but also with the operating conditions for a plant of given capacity. Thermal data have been collected since 1945 from a commercial-scale lignite-gasification pilot plant operated by the Bureau of Mines at Grand Forks, N. Dak. The description and operation of this plant and a study of the gas-composition data have already been described in previous reports (1, 2, 3, 4, 5).2) / This investigation was made to review the thermal data taken in tests and to correlate them in terms of the fraction of undecomposed steam and the H2:CO ratio.

Jan 1, 1953

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

By Edward W. Parsons

Conventional rock-bolt anchors often fail when installed in weak formations. The purpose of this work was to develop an anchor that would utilize an explosive charge to secure anchorage in any type of rock. Laboratory work to develop a rock-bolt anchored by explosive forming was initiated using rock-bolt models which had a drilled explosive chamber and were composed of various metals. This was followed by the use of several types of seamless tubing which were expanded with a water-coupled explosive capsule. By attaching a length of solid bolt to the anchor tube, a prototype explosive-anchored rock bolt was made. More than 150 laboratory models were expanded during this phase of development, During two field tests in underground mines (A and B) and one in an open- cut mine (C), 87 explosive-anchored bolts, 9 slot-and-wedge bolts, 2 bolts anchored with expanding grout, and 28 expansion-shell bolts consisting of three types of shells were installed and subjected to pull tests. The field tests were run to determine the effects of variables such as the amount and placement of the explosive charge, design changes in the bolt, and the effect on anchorage of different pull-test techniques. The field tests revealed the following: Mine A. The explosive-anchored rock bolt was feasible, but changes were necessary in bolt materials and in some details of bolt design. Mine B. The design and materials of the bolt gave excellent results in hard fractured rock, but no information was obtained concerning variations in the dimensions of the anchor unit or in the explosive charge. Nine C. Varying the explosive charge to produce a beaded surface on the bolt tube and tightening of the anchored bolt before pull-testing were found to increase significantly the anchorage obtained in soft ground.

Jan 1, 1963

By David J. Kusler

This report describes a rapid, reliable, and relatively simple method developed by the Bureau of Mines Pyrometallurgy Laboratory at Bruceton, Pa., for determining lime (calcium oxide) and magnesia (magnesium oxide) in various materials containing these constituents in greater than trace amounts. Optionally, titania (titanium dioxide) may be determined for the same sample. The accuracy of the method, suitable for most purposes, is shown by comparing the Bureau results with those obtained by accepted procedures. The method has been applied satisfactorily to the routine analysis of blast-furnace slags, for which purpose it was primarily developed, and to other calcareous compositions. In the Pyrometallurgy Laboratory it has replaced the standard methods previously used to determine lime and magnesia, and has been in general use by that laboratory for the past several years. The analysis time, generally under 3 hours, is considerably less than required by standard methods.

Jan 1, 1960

By W. P. Huleatt, R. B. McCulloch

"The Big Four zinc-deposit, directly above the north bank of the Green Mountain Reservoir on the Blue River, Summit County, Cole., was discovered in 1937 by the present owner, Walter McDaniel, who lives on the property. Mr. McDaniel, together with members of his family, have worked the mine on a small scale since its beginning and have shipped quantities of sorted high-grade ore to the International Smelting Co. at Tooele, Utah, and the Combined Metals Corp. at Bauer, Utah. More recently, parts of the nine have been operated by lessees.The property had been examined previously by the Federal Geological Survey, and the geological report was made available' to the Bureau of Mines.The Big Four mining claim was located in 1937 by Walter McDaniel and his wife Frances,- who had been prospecting in the vicinity since 1933. The discovery of the high-grade zinc deposit caused considerable excitement, as it had not been regarded as a mineralized area.Mining was begun in 1937 and carried on until 1944 by Mr. and Mrs. McDaniel with the help of a few hired miners. During 1944, parts of the mine were leased: to various parties Who produced small quantities of ore but did no development work.Shipments during 1941 .totaled 752 tons; during 1942, 387 tons; and during 1943, 510 tons. From the beginning of 1944 to April of that year, 98 tons wore produced and shipped to Utah,Since the lessees began operations, a grade of 30 to 35 percent zinc has been maintained by careful sorting. No production has been recorded for 1945.The Big Four mine is situated on Colorado State- Highway 9 between Dillon and Kremmling on the south face of Green Mountain overlooking the Green Mountain Reservoir, a Federal irrigation project on the Hue River, Green Mountain rises 1,600 feet above the general level of the valley to an altitude of 9,408 feet and the surrounding terrain, i s correspondingly mountainous and rugged."

Apr 1, 1946

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964

The objective is to provide effective training on refuge chambers for underground coal miners. This training will increase knowledge about how to teach miners to operate, transport, and inspect a refuge chamber; what to expect psychologically and physiologically inside a refuge chamber; and how to decide when to use a refuge chamber. Background During 2006?2007, several disasters occurred at U.S. underground coal mines, resulting in 28 fatalities. These disasters led to new approaches to mine safety and health, as well as new federal regulations. One new technology mandated by federal legislation is the refuge chamber. Refuge chambers are movable shelters that are either made of steel or inflate from a steel skid as a tent. They can potentially save the lives of miners during an underground mine emergency by providing breathable air, food, water, and a safe environment for up to 96 hours. Because the refuge chamber is a new technology, recommendations, information, and training products are greatly needed.

Nov 1, 2009

By James A. Wasson

The Mitchell and Berea sands were cored and logged in Fred Link well K-l, Lower Newport field, Washington County, Ohio. Core and reservoir fluid analyses and available field data were studied to determine if these sands could be successfully waterflooded. The results of the study indicate that there is insufficient oil in place to form an oilbank in either the western Mitchell pool or the Berea sand, and that no commercial recovery of oil by waterflooding can be obtained in these reservoirs.

Jan 1, 1967

By N. S. Dalal, X. Shi

"Electron spin resonance measurements provide evidence for the formation of long-lived Cr(V) intermediates in the reduction of Cr(Vl) by glutathione redtuctase in the presence of NADPH and for the hydroxyl radical formation during the glutathione reductase catalyzed reduction of Cr(Vl). Hydrogen peroxide suppresses Cr(V) and enhances the formation of hydroxyl radicals. Thus Cr(V) intermediates catalyze generation of hydroxyl radicals from hydrogen peroxide through a Fenton-like reaction. Thus the mechanism of Cr(VI) toxicity might involve the interaction between macromolecules and the hydroxyl radicals.C(Vl) compounds have been found to exert serious toxic and carcinogenic effects on humans and animals (1-3). In contrast, most Cr(III) compounds are relatively nontoxic, noncarcinogenic, and nonmutagenic (1,4). Cr(VI) and Cr(III) oxidation states are different in their metabolic pathways: Cr(VI) , ions are rapidly transported across cellular membrane (1,4,5), while Cr[III) moieties do not easily penetrate cells and are not oxidized by cellular constituents (!). Since it is known that the reduction of Cr(VI) ion is required for its reaction with DNA (1), the molecular mechanisms for the intracellular Cr(Vl) reduction has been the focus of current studies but the details are still not understood.Earlier studies on the mechanism of Cr(Vl) reduction include those on the reduction of Cr(VIJ by glutathione (GSH) .0,6-8), ascorbic acid (9), glucose (10), lactose (IO), galacturonic acid (11), microsome (12), and mitochondrial electron transport chain complexes (13). These studies have shown that the Cr(VI) reduction involves the formation of Cr(V)-containing species which are often considered to be the toxic form of chromium. Thus far, however, no information is· available on the subsequent fate of those biologically formed Cr(V) species, in particular employing well defined biochemical systems. In this context, we report here our investigations of the reduction of Cr(VI) by glutathione reductase (GSSG-R). This enzyme was selected because it is ubiquitously present in cellular systems and it has been postulated to be involved in the Cr(VI) reduction (14-17) but the underlying mechanism has not been clarified. We find that the reduction proces·s involves not only Cr(V) but also ·OH radicals. We further investigate the reactivity of Cr(V) and find that it catalyzes generation of OH radical from H2O 2 through a Fenton-like reaction. The role of ·OH in Cr(VI) carcinogenicity is suggested from this study."

Jan 1, 1989

By J. G. Kirby

The total number of petroleum refineries in the United States decreased during 1951, while the total crude-oil charging capacity continued to increase. There were 350 refineries as of January 1, 1952, compared with 357 a year earlier, according to the annual Bureau of Mines capacity survey. A gain of 369,241 barrels in daily refinery crude through-put capacity during 1951 brings the total to 7,332,885 barrels daily. The capacity of the average refinery to process crude-oil was 20,951 barrels daily, an increase of 1,445 barrels daily over the previous year. Capacity added in the Texas Gulf district accounted for 36 percent of the total increase; the Indiana-Illinois-Kentucky district, 23 percent; the East Coast district, 19 percent; the Oklahoma-Kansas district, 12 percent; and the Texas Inland district, 11 percent. The California district was the only one reporting a decline in crude-oil refining capacity, the total being 14,200 barrels daily below the previous year. Reported as under construction January 1, 1952, was an additional crude-oil capacity of 282,680 barrels daily, an increase of 77 percent over the January 1, 1951, total of 160,100 barrels. The capacity now building is for the expansion of existing facilities, since no new plants had been begun as of the first of the year. Three or four companies have plans to build refineries in the Williston Basin area of North Dakota, but no definite locations or dates when construction will begin have been announced.

Jan 1, 1952