Search Documents

By Robert M. Becker

The evaluation of existing rock stresses from measurements of the change in diameter of a borehole that is stress relieved by overcoring has become a common practice, The stress evaluation has been generally based ,on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium is adapted for evaluation of in situ stress from borehole deformation measurements. A consistent triaxial testing approach for determining elastic properties of the overcore is also outlined. Comparison of isotropic with anisotropic interpretations of the state of stress show that large errors in evaluation may occur if the anisotropic character of the rock is neglected.

Jan 1, 1967

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1952 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 94 samples of aviation gasoline which include, for the first time in this series of reports, data on five samples of grade 108/135 aviation fuel. Data also are given for 34 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers? production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1953

By S. M. Shelton, R. B. Fisher, M. M. Fine

"INTRODUCTION The Batesville manganese district lies in the southern part of the Ozark region, mostly in Independence County but partly in Sharp, Izard, and Stone Counties of north central Arkansas.Oxides, carbonates, and silicates of manganese are found in the district. 4/ Carbonate ores have been mined from time to time, but the reserves of potentially commercial ore are chiefly black manganese oxide minerals.The district has produced manganese ore for many years. lip to and including 1933, 160,804 long tons of ferruginous manganese ore (10 to 35 percent manganese) and 140,277 long tons of metallurgical ore (35 percent or more manganese) were shipped;./ most of it was wad orThe term ""wad ore,"" used locally to designate the soft, clayey de¬posits of oxide ore, is a partial misnomer. The ores contain a soft, low-specific-gravity mineral of indefinite composition, which can be designated as wad, but coarse and fine particles of psilomelane and hausmannite, with a smaller proportion of braunite, pyrolusite, and indefinite manganese silicates, are also present. Large and small lumps of high-grade, hard manganese oxide minerals are found, frequently embedded in a soft, black matrix of fine particles of manganese oxides mixed with gangue."

Jul 1, 1942

By O. C. Blade

"INTRODUCTION This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1952 was mode under a co¬operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior.Analytical data are presented for 94 samples of aviation gasoline which include for the first time in this series of reports, data on five samples of grade 108/135 aviation fuel. Data also are given for 34 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' production in their laboratories and the results sub¬mitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.SUMMARYA comparison of certain properties of the commercial aviation gasolines produced in the United States during 1950, 1951, and 1952 is presented in table 1, the 1952 data being average values from tables 3 through 7 of the present report. Trends in certain characteristics of these fuels may be seen in figures 1 through 5 which also indicate the minimum and maximum values. As may be observed, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-fuel survey reports published by the Bureau of Mines is given on page 7.Table 2 presents a summary of data from table 8 and compares properties of aviation jet fuels of 1952 with summarized data on jet fuels of October 1951."

May 1, 1953

By Harry K. James

Experimental studies of the physical and explosion characteristics of pure hydrazine nitrate and multicomponent systems containing hydrazine nitrate, supplemented with an extensive Literature survey, are presented. Such proper- ties as melting point, heat of fusion, density, viscosity, surface tension, thermal stability, decomposition process, detonation velocity, impact sensitivity, and TNT equivalence are included.

Jan 1, 1970

By Larry D. Nichols

Poroplastic membranes containing ion exchange liquids were studied for separating cobalt from nickel-containing solutions similar to ammoniacal laterite leaches. The driving force for cobalt transport was differences in pH and composition between the leach and extraction streams. Using a diketone ion exchange liquid, a leach pH of 6.5 to 7.0, and a strip pH of 2.3, cobalt was extracted from a 750 ppm solution containing 2500 ppm of nickel at rates ranging from 1 to 10 µg/cm2 .min in single membrane cells, and from 10 to 100 in more closely spaced multiple membrane cells. Rates were variable, with evidence that cross -membrane flow pasterns were a key factor; a reproducible rate of 30 pg/cm .min would be economically viable. Loss of transport observed after several days of continuous operation was restored by flushing membranes with fresh ion exchange liquid. A major effort was devoted to preparation of thin, leak-free membranes; the resulting membranes endured operating conditions without mechanical failure.

Jan 1, 1982

By H. B. Hill

The discovery of the Oklahoma City field and its .rapid development into one of the major oil-producing districts is an outstanding epoch in the history of the petroleum industry not only of .Oklahoma but also of the United States. The relatively great depth to which the wells were drilled and the large initial production of high-gravity oil are of special significance. The field has boon under proration almost from the time that its development began, and many new production problems have developed out of the changed conditions of operation. The discovery well was first tested in December 1928 at a depth of 6,402 feet, with an initial production of 4,847 barrels of 38.5° A.P.I. gravity and several months later was completed at a depth of 6,624 feet. The large initial production, the high pressure, and the large gas volume in the different horizons of the discovery well suggested the potential possibilities of gas and oil, production in formations of Pennsylvanian and pre-Pennsylvanian age.

Jan 1, 1933

By Murray Jacobson

Data obtained by the Federal Bureau of Mines on the dust explosion hazard in air are presented for 220 samples of agricultural products. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum electrical energy for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent flame propagation, and, in a few instances, the permissible oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle size and source of sample on explosibility are shown. The relative ignition sensitivity, severity of explosion, and overall explosibility of the materials are characterized by empirical indexes. This report contains Ma obtained by the Bureau in laboratory studies on the explosion hazards of agricultural dusts. Recognition of the dangers will encourage adoption of adequate measures to prevent ignition and explosion during preparation, processing, and utilization of the materials. Agricultural products constitute one of the largest groups of materials used in America. More than 260 million tons of various grains, much of which now exists in dust form, was grown in 1958.6/ Over 600,000 tons of the annual production of 200

Jan 1, 1961

By R. F. Kendall

Only a limited number of mass and infrared reference spectra of high purity unsaturated hydrocarbons and oxygenates are presently available in the literature. To aid Bureau of Mines research programs requiring such references, 64 mass spectra and 70 infrared spectra were obtained and are reported. The individual compounds, acquired from commercial sources, were purified by preparatory gas chromatography. Purity determinations were made using a combination of analytical gas chromatography, microhydrogenation, and catalytic deoxygenation. These spectra will aid spectroscopists in the identification of compounds of the types reported.

Jan 1, 1966

By A. C. Johnson, McHenry Mosier

The Bureau of Mines has adapted its activities to needs of national defense and to conditions brought about by the war program . Its work is now oriented solely to war problems . After studying about 1,600 deposits of war minerals , exploration projects have been undertaken on 96 of the most promising , of which 56 have proved successful . These have indicated that 56 million tons of ore of commercial or near -commercial grade can be utilized to meet war requirements . Included in this amount are 1 million tons of tungsten ore ; 4 million tons of chromite ore, 10 million tons of manganese ore , 2 million tons of antimony ore , 1 million tons of mercury cre , and 28 million tons of iron ore . Work done in connection with exploration projects included 172,000 feet of surface trenching , 210,000 feet of drilling , and 21,000 feet of shaft sinking . Nearly 100,000 samples were taken, on which 500,000 analyses were made . Extensive metallurgical tests were made on ore from many of these deposits , both in the laboratory and in pilot plants , in connection with research to develop metallurgical processes for their treatment .

Jan 1, 1943

By N. L. Kozlinsky, B. W. Gandrud

"The Marvel mines 1 and 3 of the Roden Coal Co. are located in the Cahaba field in Bibb County, Ala., nearly southwest from Birmingham, an airline distance of roughly 30 miles. The coal of the Clark seam at this point has some coking properties, but at present it is sold exclusively as a domestic and steaming coal.This paper, which is the second of a series on the washability of Alabama coals, like its predecessor dealing with the Mary Lee seam,5 contains screen-sizing and float-and-sink tests of a representative sample of the raw slack, and slotted-screen tests showing the proportions of flaky particles in certain selected sizes; inasmuch as this coal is not used for coke manufacture, no crushing tests have been made. These data have been obtained in connection with an exhaustive study of coal preparation in Alabama, now being conducted by the United States Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. As the work progresses, other papers will follow containing further data on Alabama coals and giving results obtained in preparing these coals by various methods.The only published investigative work on the Clark seam is that of Forbes,6 who gives a number of sections of this seam in Marvel No. 3 mine with proximate and ultimate analyses of face samples taken in the mine and also some analyses of delivered coal.The available information on this coal indicated that the preparation problem was one of ash reduction. In order to substantiate this information a complete analysis of the 3/4 by 3/16 inch size, and sulphur determinations and ash-fusibility tests of the float-and-sink fractions have been made; these results are given in Tables 1 and 2. As these results also indicate that the preparation problem is one of ash reduction, the tests and discussion have been devoted to that subject."

Jun 1, 1930

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By M. R. Geer, H. F. Yancey

Fuel requirements of the Pacific Northwest have been increased greatly by the war . To the normal peacetime demands for fuel have been added the requirements of new industrial and metallurgical plants engaged in war production , the increased demand arising from expansion of existing industrial establishments , increased amounts of railroad fuel required to handle wartime traffic , and increased quantities of domestic fuel required by the influx of war workers . In the face of these augmented demands for fuel shipments of fuel oil have been curtailed , wood fuel which normally is an important factor in both industrial and domestic markets of the area is less abundant , and the production of coal in Washington has decreased sharply . The fuel requirements of the region have been met so far by shipping large tonnages of coal into the Pacific Northwest from Utah , Wyoming , Montana , and Colorado ; the quantity received from these States and Canada in 1943 amounted to 2,688,9124/ tons , 175 percent of the Washington production . or The proximity of the Washington coal mines to large centers of war production has resulted in widespread migration of miners to employment in shipyards and aircraft plants ; the ensuing shortage of miners largely accounts for the decreased production of coal in the State . Hence , strip mining , which requires relatively few workers and a shorter time for development , offers an attractive means of alleviating the local coal shortage and obviating the necessity of shipping coal from the producing areas of the Rocky Mountain States to the Pacific.coast . So urgent has been the necessity for augmenting local coal production that any coal property that promises to be amenable to strip mining , even though the coal may be inferior in quality , has warranted examination . Even low- grade coals that cannot compete in the normal market can be used locally , thus releasing better coals for shipment to critical centers. of consumption ... One such deposit of low- rank fuel examined by the Bureau of Mines is in western Lewis County , about 9 miles east of Toledo , Wash . The coal is lignitic and on the as - received basis has a heating value of 6,000 to 6,500 B.t.u. per pound . The property is of interest primarily because the physical conditions favor operation by stripping and offer opportunities for low- cost production with very low manpower requirement .

Jan 1, 1945

By W. H. Blackburn

This paper describing the milling practice at the Tybo concentrator is one of a series of similar papers being prepared by the United States Bureau of Mines on milling methods and costs at the various mills in the United States. ACKNOWLEDGMENT A large part of this paper way prepared by H. M. Lewers, mill superintendent of the Tybo plant of the Treadwell Yukon Co., Ltd.

Jan 1, 1931

By M. H. Chetrick

Since 1945, a commercial-scale pilot plant for the gasification of lignite has been operated by the Bureau of Mines at Grand Forks, N. Dak. The description, operation, and objectives of this pilot plant have already been described in previous reports (6, 7, 8). Although the experimental data obtained from the operation of the externally heated retort have been tabulated and summarized (1, 7), few studies have been made in the correlation of these data. The purpose of the present investigation was to review the data taken in tests of the lignite-gasification pilot plant and to correlate the gas-composition data in terms of their basic factors.

Jan 1, 1950

By G. B. Botsford

In August 1943 the Bureau of Mines began an investigation of the West Portal magnetite mines, which comprise the Swayze and Turkey Hill properties. The work included (1) traversing with a dip needle to record magnetic anomalies, (2) diamond drilling, and (3) sampling old mine dumps; it was completed in April 1944. The deposit consists of two parallel veins, which strike northeast and dip southeast. They carry magnetite in gneiss and schist. The Swayze mine was discovered in 1867 and closed in 1889, while the Turkey Hill mine was opened in 1872 and closed in 1887. The dip-needle survey covered 266 acres. The diamond drilling comprised 11 holes totaling 4,910 feet from which 142 samples were taken for chemical analyses. Old mine dumps were sampled at 52 points for chemical and magnetic analyses.

Jan 1, 1948

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

By Wallace W. Roepke

Research on coal cutting at the Bureau of Mines Twin Cities Research Center (TCRC) has evolved from a purely mechanical approach, specifically to reduce dust or frictional methane ignitions, into an understanding of the complexity of the cutting system relationships. Achieving an understanding of these relationships requires a wide variety of testing techniques and equipment. Laboratory facilities and the associated equipment exist for shallow to deep cutting in both coal and coal-inclusive rock with any desired bit type. Research efforts with this equipment are providing insight for significant advances to help solve the problems of pneumoconiosis and frictional ignition. This effort will ultimately affect both respirable dust and methane ignitions at the face through better bit design and will increase the salable percent of run-of-mine (ROM) coal processed. It will also affect the design of rotary-drum cutting continuous mining machines (CMM) and longwall machines. This report describes the main features of the coal cutting research facilities at TCRC.

Jan 1, 1983

By Charles L. Harness

Magnesia (MgO) has a variety of uses, and it has become increasingly important as a war material because of the imperative demand for refractories to line metallurgical furnaces, and because magnesia is used to make the in aircraft and other implements of warfare. Magnesia occurs as an integral part of nearly 60 minerals, but it is extracted commercially from only a .smaller number, of them. The present commercial sources are magnesite, brucite, dolomite, raw sea water, sea water bitterns, and well brines. Magnesia Raw Materials Magnesite magnesium, carbonate MgCO3, theoretically contains 47.8 percent MgO and 52.2 percent CO2. There are two varieties of magnesite, crystalline and cryptocrystalline (dense or amorphous). The latter type, though, not so plentiful as the former, is generally purer. It resembles unglazed write pottery in texture, whereas the crystalline variety is generally dark and granular, though the color may vary. The principal domestic deposits, of crystalline magnesite are near Chewelah, Stevens County, Wash. (which has supplied most of the magnesite mined in the United States), in the Gabbs Valley area of Nevada (near Luning); and in Llano County, Tex. Crypto-crystalline magnesite occurs principally in California. Magnesite occurrences have also been reported in several other States, including New Mexico, New York, New Jersey, Pennsylvania, Massachusetts, Vermont, and Maryland, but these deposits have not been developed commercially.

Jan 1, 1943

By Virgil A. Marple, Susanne V. Hering

"5.1 IntroductionTraditional impactors do not offer much size resolution for submicrometer particles; typically their finest size cut is around 0.4 µ.m. Yet for many aerosol applications it is useful to be able to size segregate aerosols in the size range below 0.4 µ.m. Diesel emissions, welding fumes, cigarette smokes and photochemically generated smog aerosols typically exhibit mass median diameters between 0.1 and 0.6 µ.m. When sampling these aerosols with a traditional impactor, fifty percent or more of the aerosol mass can penetrate the final impactor stage. Allhough the material can still be collected on a backup filter, the filter gives no size resolution. As a result, the investigator has no size information on a substantial portion of the sample. One needs a sampler that size-segregates the majority of the aerosol mass. A lower size cut of 0.1 µ.m or less is required for most combustion smokes and smog aerosol s.To obtain smaller cutpoints two types of impactors have been developed, namely low-pressure impactors and micro-orifice impactors. Both instruments can provide cutpoints as small as 0.05 µ.m. Low-pressure impactors were introduced more than twenty years ago (Stem et al., 1962), and a variety of these samplers are in use today. Micro-orifice impactors have been developed at the University of Minnesota within the last five years (Marple et al., 1981 ). To date theirs are the only examples of these instruments in use.5.2 Operating PrinciplesThe low-pressure and micro-orifice impactors use two different approaches to achieve their very small particle-size cuts. Low pressure impactors resemble ordinary impactors, but are operated at reduced pressures of 5-40 kPa (0.05 - 0.4 atm). They take advantage of the decreased aerodynamic drag on particles that occurs when the mean free path in the air is as large or larger than the particle diameter. Micro-orifice impactors operate at near atmospheric pressure, but employ very small orifices, 40 µ.m to 200 µ.m in diameter. The streamlines of the air impinging upon the impaction plate have correspondingly smaller radii of curvature; the air is accelerated more quickly, making it more difficult for the particles to follow. The basic operating principles for both types of impactors are evident from the particle Stokes number, defined as:"

Mar 1, 1989