Search Documents

By W. W. Adams

The safety record established by the coal-mining industry of the United States during 1934, although not as favorable as that for the previous year, was better than the record for any other year during the period 1930-34 for which complete figures covering fatal and nonfatal accidents at the mines are available. The number of accidents was 89.98 per million man-hours of employment compared with 86.74 for the year 1933, the latter being the lowest rate in any of the 5 years referred to. The rate was 105.60 for 1930, the first year covered by available data. Employment increased in 1934; the number of workers represented an increase of 8 percent over the year 1933, man-shifts of labor increased 16 percent, and the number of man-hours of labor increased 7 percent. The total number of man-hours of employment also exceeded the number reported for 1932, and was almost equal to the record for 1931.

Jan 1, 1936

By Forrest T. Moyer

INJURY experience in the metal and nonmetal mineral industries during 1964 was better in rates of occurrence but worse in severity rates than in 1963. The frequency rate of injuries per million man-hours was improved at metal mills, nonmetal mines, and sand and gravel operations, and was virtually unchanged at metal mines; however" the rate of occurrence of work injuries at nonmetal mills, stone operations, nonferrous reduction and refining plants, and slag plants was higher than in 1963. The severity rate of injuries during 1964, data for which are presented for the first time in this chapter, was better at metal mills, nonmetal mines, stone operations, and slag plants. However, the severity rate was worse at metal mines, nonmetal mills, sand and gravel plants, and nonferrous smelters.

Jan 1, 1965

More than 400 academic, Government, and industry representatives attended the third symposium on ash utilization and technology held in Pittsburgh, Pa., March 13-14, 1973. Sponsored by the American Public Power Association, Edison Electric Institute, National Coal Association, National Ash Association, and Bureau of Mines, the symposium Featured 26 formal presentations by leading experts from Europe and the United States on all major phases of ash production, utilization, and research. Abstracts of all the papers are grouped right after this introduction, and the full symposium proceedings follow. Sponsoring organizations and their chief representatives were the National Coal Association, James R. Garvey, Bituminous Coal Research, Inc.; Edison Electric Institute, C. E. Brackett, Southern Electric Generating Co.; American Public Power Association, Herbert Blinder, Columbus (Ohio) Electricity Division; National Ash Association, Inc., James N. Covey, Rochester Gas and Electric Corp.; and the United States Department of the Interior, Bureau of Mines, William L. Crentz.

Jan 1, 1974

By Charles L. Kimbell

The year 1986 was not a good year for the world's mineral industry from several viewpoints. Levels of production, both of crude minerals and processed forms, registered declines in the cases of a greater number of commodities than the number that recorded increases. The overall value of world crude mineral production was estimated to have increased, but only very slightly in terms of constant dollars to nearly $997 billion. Although there were modest increases in the consumption of all major fuels and most major metals, the latter at least apparently resulted more from drawdowns of inventories than from increased production (fuel consumption increases did come from higher output levels), and consumption of most major fertilizer and chemical commodities (nitrogen, phosphate, and sulfur) were at lower levels than those in 1985. Prices for a number of mineral commodities declined, headed by the very substantial drop in world crude petroleum prices, but also including downturns for a number of metals and industrial minerals as well. There was insufficient information to reliably fix the level of the dollar value of world trade in minerals, for while output was up in the case of some large-volume materials such as iron ore, coal, and crude and refined petroleum, suggesting that the volume of trade in physical units may have increased, declining prices may well have offset quantitative gains.

Jan 1, 1988

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By M. Karmis

Surface subsidence is an inevitable consequence of many underground mining operations and has been recognized as such since the fifteenth century. Damage resulting from this phenomenon ranges from simple land settlement to severe structural damage to buildings and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). In fact, it is estimated that over 2 million acres of land across the United States have been affected by mining subsidence, of which 140,000 acres are in urban areas (Singh, 1978; Johnson and Miller, 1979). Further, it is estimated that during the next twenty years an additional 1.5 to 2.4 million acres of land will also be affected by mining. Subsidence prevention is not feasible, at least under the existing technologic and economic constraints of underground coal mining. Foreign experience has demonstrated, however, that subsidence can be successfully controlled if an accurate method of predicting ground movements is available. Such techniques have been developed in many coalfields, where it is currently accepted that subsidence can be predicted within ± 20 percent of the actual values. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented.

Jan 1, 1983

By Homer J. Ballinger

"SUMMARYDuring December 1945, the Bureau of Mines began churn drilling the Winchester zinc deposit, 11 miles south of Joplin in Newton County, Mo. The deposit lies in a virgin area northwest of the Seneca fault. It is one of several deposits partly proven by drilling but never developed.Logs of 28 privately drilled holes had indicated a substantial tonnage without delimiting the deposit. It appeared that additional drilling might increase this reserve sufficiently to justify mining. A, total of 6,33 feet of churn drilling was completed in 17 holes drilled by the Bureau of Mines. Twelve of the holes penetrated minable ore extending the length of the known deposit and materially increasing its estimated tonnage.INTRODUCTIONDuring May 1943, the Winchester property in Newton County, was visited by an engineer 3/ of the Bureau of Mines, accompanied by Dr. A. N. Winchester, owner, and Charles Keith, lessee of the property. At the request and with the assistance of these gentlemen, examination of the property was undertaken. Logs of 28 churn-drill holes were collected, hole locations were surveyed, and available historical data were obtained. It was concluded that although existing drill holes indicated considerable reserves, additional drilling might increase the tonnage substantially. In addition, it was believed that better knowledge of this ore deposit could be obtained by drilling further, and this knowledge could, in turn, be applied to other less proven deposits in the same field."

Jul 1, 1947

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and materials.

Jan 1, 1978

By Kenneth J. Miller

The Bureau of Mines two-stage coal-pyrite flotation process was modified to provide a more concentrated final clean coal slurry underflow which could be dewatered economically by filtration or centrifugation. This was accomplished by doing the first-stage coal flotation step in the conventional manner with a slurry of about 8 percent solids, but running the second-stage pyrite Flotation step with undiluted coal froth concentrate containing about 25 percent solids. The final clean coal underflow produced by the new technique contained between 26 and 30 percent solids; this pulp was sufficiently concentrated to be filtered industrially without further thickening. Sulfur removal was equal to that obtained using dilute second-stage pulp,

Jan 1, 1975

By Eric E. Cather

A mineral survey of a portion of the Lake Eleanor RARE II area (No. 5807), Trinity County, California, was done by the U.S. Bureau of Mines and U.S. Geological Survey (USGS). Approximately 8,650 acres (3,500 ha) of the Lake Eleanor RARE II area not examined for this report had been previously investigated by U.S. Bureau of Mines and U.S. Geological Survey personnel and published as part of USGS Bulletin 1371-B, (Hotz, 1972) Mineral Resources of the Salmon-Trinity Alps Primitive Area, California. The report showed that the section included in the rake Eleanor RARE II area contained no metallic mineral resources. Geochemical sampling indicated that the Lake Eleanor RARE II area contains no potentially important mineral resources. About 4,650 acres (1,880 ha) of the eastern part of Lake Eleanor RARE II area were examined for this report. The Bureau of Mines was responsible for detailed examination and sampling of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. This area is underlain mainly by granitic rock and serpentinite.

Jan 1, 1981

By A. E. Ketler

The Bureau of Mines Research Program has defined per coal miner's illumination needs. Due to similarity in the environment in which coal and Hardrock miners work, coal mine illumination technology has been applied to Hardtack room and pillar mines.

Jan 1, 1977

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United States. The first report7 on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline.8 The present paper reports results of the examination of the gasolines for color, doctor test, gravity, end point, per cent recovered, copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978

By Ovsei Volberg

Motion capture involves recording the position and global orientation of joint sensors of a real object, in most cases a real person performing some human activities. This information is usually recorded at uniformly spaced instances of time, or as it is often called frame-by-frame. Then the recorded motion data sets are processed and mapped into a skeleton hierarchy of a virtual, computer simulated human figure to control the motion of the virtual human in the computer simulation. In the first part of the paper we review several new techniques developed to facilitate the manipulation, noise reduction, storage and reuse of captured data, which have a potential to reduce the overall cost of motion simulation and improve its realism. In the second part of the paper we consider the real life problem of reducing a worker?s risk from being hit by underground mining machinery in a confined space. We formulate a set of requirements to motion editing for this particular task and analyze the limitation of existing techniques

Jan 1, 2000

Since roof falls in the vicinity of the working face in underground coal mines are a major source of fatalities and injuries in this country's coal mines, it is evident that the present systems of temporary support for use in this working area are ineffective. This seems to be chiefly due to the inconvenience of setting up heavy and awkward devices such as jacks, posts and the like, which also interfere with the movement of men and machines in this critical working area. This program was concerned with defining and testing commercially available materials that could be used as support elements in a more convenient flexible personnel shield. The objectives of this program were to: 1. survey the materials that might provide the support elements of a flexible-material personnel shield for use in underground coal mines and prepare a list of those materials which appear most suitable for use in coal mines. 2. prepare a proposed testing plan for the materials to be selected from the aforementioned list by the Bureau of Mines for further evaluation. The test plan was designed to provide the following information: a. Tensile strength. b. Proportional limit. c. Creep characteristics at room temperature. d. Elastic properties depicted by stress-strain curves. Properties were tested in two directions for woven fabrics. e. Density. f. Resistance to abrasion. g. Resistance to attack by mine atomsphere. h. Resistance to humidity. i. Impact characteristics.

Jan 1, 1972

By Gerald T. Homce

Data from the U.S. Bureau of Labor Statistics show that 89 water well drillers died on the job between 1992 and 2002, and 28 of these deaths were electrocutions (Figure 1). In fact, elec­trical accidents are the leading on-the-job killer of water well drillers. The use of electricity is such an integral part of our lives that we usually take it for granted, but if we don?t understand or choose to ignore the hazards associated with electricity, the results can be deadly. Why is electrical shock so dangerous? If the voltage (of a shock) is sufficient to drive electrical current through your body, just 10 milliamps of cur­rent (1000 milliamps = 1 amp) can cause muscles to contract and prevent you from releasing an energized wire or tool in your grip. As little as 30 milliamps of current can paralyze your breathing, and 75 milli­amps can cause your heart to stop pumping blood (ventricular fibrillation). As a comparison, a small bedroom night-light draws about 30 to 60 milliamps. Other factors influence how severely you?ll be shocked if you touch a live electrical circuit, such as the path electrical current takes through your body and how long it flows, as well as your body weight. How much voltage is needed to drive electrical cur­rent through your body? Not much! Generally, any power source at 50 volts AC or higher is considered dangerous.

Jan 1, 2008

By Frank E. Cash, Roy G. Stott

This circular describes four modern change houses of the Lake Superior iron - ore district , all conceived and constructed since 1937. The oldest change house described herein was constructed and occupied in 1938 , yet it embodies the modern improvement of air - conditioning . The purpose of this report is to describe and illustrate improvements with regard to health and safety features combined in the construction , arrangement , ventilation , heating ,lighting , and other features , with the aid of photographs , sketches , and diagrams . The modern change house is a fire - resistant structure in which intermingling of men in mine clothes and men in street clothes , hazardous dust , heat and humidity , crowding , poor lighting , slippery and muddy floors , and inadequate facilities for clothes and for bathing have been largely eliminated . The miner coming off shift at a modern mine no longer faces the elements when he gets off the cage . He travels through a tunnel to the change house , where he is cooled gradually by room temperatures as he passes from the mineclothes section and shower room to the street - clothes room . He is assured of dry clothes when he is ready for them . No longer is he sent out of the change house into a muddy yard to drive away as best he can . The modern change house has an improved parking lot and graveled or concreted walkways from it to the change house entrances .

Jan 1, 1949

By Nicholas T. Zilka

Mineral resource studies by the Bureau of Mines indicate three areas within the Selway Bitterroot Wilderness have mineral resource potential. Regional studies suggest that a granitic stock on the south side of the Wilderness has high potential for a Climax-type stockwork molybdenum deposit (pl. 1, no. 8); but detailed surface investigations failed to recognize a deposit. The Elk Summit area on the north side of the Wilderness contains subeconomic resources of columbium (niobium)-bearing ilmenite in placers (p1. 1, no. 19). Subeconomic silver-copper-lead resources occur in a vein on the northeast side of the Wilderness at the Clift Mine (pl. 1, no. 2-5). The study area has no known deposits of oil and Haas, coal, geothermal resources, or other energy-related commodities.

Jan 1, 1982

By Linneas W. Laage

The purpose of this report is to document the fire experiments conducted at the Waldo Mine, NM during March 1990. The U.S. Bureau of Mines is concerned with improving and validating the predictive capability of the mine ventilation and fire simulator, MFJRE. To accomplish this, fire experiments were conducted at the Waldo Mine and temperature profiles were developed as functions of time and distance from the fire. These tests then provided data for verifying the heat transfer model in the MFIRE mine ventilation and fire simulator. An initial analysis of this data indicates that it will serve this purpose well. This report summarizes the data obtained during six fire tests at the Waldo Mine.

Jan 1, 1994