Search Documents

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle developed under U.S. Bureau of Mines Contract No. JO 366003, "Improving Man Transit Safety". This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements were embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery-powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle is presented in Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By Tyler Blake

This report describes a study designed to evaluate a pro-posed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation was performed comparing a prototype with the standard, currently available cord. First, a ?pull test? equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By J. E. Chilton

A technique for use in underground coal mines measures the response times of machine-mounted methane monitors. This technique uses a calibration cup to deliver gas to the sensor head to measure response times. For comparison, in the current study, response times were measured by placing methane sensor heads in a specially designed test box where they were exposed to an atmosphere containing a constant concentration of methane. Response time readings measured in the test box were shorter than the readings obtained using the calibration cup. The response times measured in the test box were comparable for sensors from three different manufacturers. The effects of dust cap and flame arrestor design on response times were also evaluated using the test box.

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade. By the late 1990s, longwall mine output accounted for 40 percent of all underground output in the U.S., and today longwall mines account for approximately 50 percent of coal produced underground in the United States. A 53 percent increase in average shift production rates has occurred over the last fifteen years. This increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust provides an ongoing challenge for coal mine operators. The National Institute for Occupational Safety and Health (NIOSH) has completed a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify dust generation from major sources on the longwall section and to determine the relative effectiveness of the different control technologies in use today. Substantial reductions in dust levels were realized at sampling locations on the face when compared longwall surveys conduct in the 1990?s. This paper summarizes the results from the underground dust surveys and discusses current longwall dust control technology and operating practices.

Jan 1, 2010

By C. A. Komar

The Bureau of Mines conducted oil-displacement tests in the laboratory with three water-in-oil and five oil-in-water emulsions that were created with ultrasonic energy at a frequency of 20 kHz and an acoustic intensity of approximately 100 watts per cm2. Emulsions of either crude oil or kerosine, brine, and 112 to 2 percent emulsifier were formed during 30 seconds of acoustic irradiation. Results indicate that ultrasonic energy induces greater and more uniform dispersion of one liquid in another in the presence of small amounts of chemi¬cal emulsifiers. When the emulsions were injected as a buffer slug before waterflooding, recovery of the oil-in-place was 8 to 22 percent greater than with conventional waterflooding in the test specimens, regardless of the con¬tinuous phase (oil or brine). The emulsions do not appear to be applicable to the Appalachian area; however, because the oilfields are too "tight," the clays in the formation remove the emulsifier from the displacing fluid, and not enough additional oil is produced, compared with recovery using conventional waterflooding, to warrant the increased operating costs.

Jan 1, 1969

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By J. M. Gomes

Bench-scale flotation tests were conducted on two western tactite ores to study the recovery of tungsten and zinc minerals. The investigation, which is part of the Bureau of Mines ongoing program to develop methods for beneficiating minerals and metals from domestic low-grade ores, demonstrated the feasibility of producing scheelite, sphalerite, and their bulk concentrates. Sphalerite concentrates containing 51 to 53 pet Zn and less than 0.11 pct W03 were selectively recovered prior to scheelite flotation. Zinc recovery ranged from 85 to 91 pct. Scheelite concentrates containing 17 to 25 pct W03 were then recovered from the ore; tungsten recoveries ranged from 88 to 94 pct. Bulk flotation concentrates containing 84 to 91 pct of the W03 and 87 to 95 pct of the zinc also were prepared. More than 98 pct of the W03 in a bulk concentrate containing 9 pct W03 was extracted by autoclave leaching with a soda solution. The zinc remained in the leached residue.

Jan 1, 1982

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By A. C. Johnson

The T. L. shaft of the Eureka Corp., Ltd., near Adams Hill, Eureka, Nev., was sunk in 1954 and 1955 to permit exploration and development of the lead-zinc-silver ore that had been indicated by drilling. This paper describes the sinking of the 4-compartment, vertical shaft to a depth of 1,127 feet and includes pertinent details of equipment, methods, and costs. A shaft crew of 10 men, supplemented by 13 hoistmen, topmen, carpenter, and shop crewmen, sank and timbered the 1,127 feet of shaft in 630 workdays. Total labor per foot of shaft was 107.95 man-hours. Supplies per foot of shaft included 20 pounds of explosives, 1.61 pounds of drill steel, and 200 board-feet of timber. Power consumption, including that required for pumping, averaged 3,726 kw.-hr. per foot.

Jan 1, 1958

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983

By J. A. Kosek

Work has been conducted under Bureau of Mines Contract Number HO 357078 to develop instruments for detecting CO, NO and NO2 in a mine atmosphere, using fuel cell technology. The approach has been to optimize the fuel cell sensor configuration for the specific detection of CO, NO and NO2 in the presence of other mine gases utilizing recent advances in catalyst, electrode and solid polymer electrolyte membrane technology. Para-metric testing has been conducted on three electrode sensor cells to define performance and life characteristics as a function of temperature, feed flow and applied sensor voltage. Extended life testing has been performed on sensor cell configurations exhibiting favorable characteristics. Reliable, efficient gas sampling and electronic control circuitry has been fabricated for use with the sensor cells, and integrated into devices to meet the performance and design specifications for portable, battery-powered, hand held direct indicating gas detectors for use underground. Twenty of the production-type, direct indicating CO detectors have been tested and delivered to the Bureau of Mines under the present contract. Three prototype diffusion head CO monitors have also been delivered for evaluation under the pre-sent contract. The gas sampling pump and related parts have been replaced by a diffusion tube assembly in which CO reaches the sensing electrode surface by diffusion alone. In addition, delivery will be made of ten direct-indicating nitric oxide detectors and ten direct-indicating nitrogen dioxide detectors. These instruments are very similar in design to the direct indicating CO detector.

Jan 1, 1979

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980

By A. Gene Collins

Potassium, lithium, strontium, barium, and manganese are present in many oilfield brines, None of them except barium is determined routinely in brine analyses. Therefore, sensitive and accurate flame-spectrophotometric methods were developed. Potassium, lithium, and strontium were determined by a standard-addition technique in ethyl alcohol solutions. Barium and manganese were determined in ethyl alcohol and normal propyl solutions, respectively, after interfering substances were removed.

Jan 1, 1962

By Lon A. Williams

This appendix contains drawing lists and drawings of components and assemblies designed for the prototype portable and machine mounted lighting systems per Tasks II & IV of Contract No. H0220065.

Jan 1, 1976

By P. -É. Boileau, S. Mandapuram, Shiping Ma, S. Rakheja

The absorbed power (PAbs) has been suggested as a better measure of human responses to whole-body vibration, since it relates to the cumulative energy dissipated by the body exposed over a given duration. Moreover, unlike the other measures, the PAbs can adequately account for the intensity of exposure. Although, the vast majority of off-road vehicles impose considerably severe vibration along the horizontal axes, the vast majority of studies on biodynamic response characterization consider only vertical vibration. Only a few studies have reported PAbs responses of the seated human body exposed to horizontal vibration and the major contributing factors [1]. This study aims to characterize the PAbs responses of seated human subjects to horizontal (uncoupled x- and y-axis) vibration as functions of the vibration intensity, subject mass, seat height and the, type of back support. Methods Experiments were conducted using a rigid seat with an adjustable backrest inclination and seat height. The seat was installed on a horizontal vibration simulator and the forces at the seat base and the backrest were measured by three-axis force plates. Two single-axis accelerometers were installed on the seat back and the platform, oriented along the axis of motion. The experiments were performed using three different seat heights (350, 390 and 410 mm), back support conditions (NB- no back support and sitting erect; Wb0- Upper body supported against a vertical back support; and WbA- back supported against an inclined backrest, while sitting relaxed) and three different magnitudes of broad band excitations in the 0.5-10 Hz frequency range (0.25, 0.5 and 1 m/s2 rms acceleration under x-axis and y-axis, applied independently). A total of 8 healthy adult male volunteers with total body mass ranging from 59.4 kg to 92 kg and aged between 21-51 years took part in the experiments. The subjects were seated with their hands in lap, and feet supported on the moving platform for each posture. Each measurement was repeated 2 times, while the data were analysed using a bandwidth of 50 Hz and frequency resolution of 0.0625 Hz. [ ] The data were analyzed to derive the absorbed power characteristics of the body at both seat pan and backrest interfaces, while the coherence among the measured forces and accelerations wer

Jan 6, 2006

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987