Search Documents

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

By Clayton J. Bossart

The design and fabrication of an engineering model and three prototypes of a portable gas analyzer and sapling system is herein described. This design effort has provided a battery operated system which will indicate the degree of explosivity of return air and in the air beyond the seal during the course of fighting, sealing and quenching a mine fire. Performance tests, design criticisms and recommendations for designs are also included. The system is based on two analyzers: the MSA Catalytic Combustible Gas Analyzer for indication of total combustible gas concentration and a modified, totally automated version of an Analytical Instrument Development Corporation Model 622 gas chromatograph (CC) for analysis of individual gases. The system provides continuous monitoring of combustible gas level in the range of 0 to 100% LEL. The GC automatic analysis requires a 5 minute cycle time to update the concentration indications for: hydrogen @ 0 to 10% oxygen @ 0 to 25% nitrogen @ 0 to 100%, methane @ 0 to 10 or 0 to 50%, carbon monoxide @ 0 to 5% and carbon dioxide @ 0 to 10%. CC peak heights are translated into concentration units which are memorized and continuously displayed on Integral meter readouts. The underground analyzer system design was reviewed and tested by the MESA Approval and Certification Group and found to meet intrinsic safety requirements. The three underground packages consists of: a gas chromatograph with dimensions of 11" X 12" X 16" and weighing 25 lbs. , an electronics unit 10" X 14" X 19" in size and weighing 30 lbs., and a power pack 6" X 14" X 16" in size and weighing 45 lbs. Two AC/DC power supplies are provided for aboveground battery charging and system operation in the laboratory. The underground system is entirely automatic and self-contained, including sources for electrical and pneumatic power and for CC carrier gas via a rechargeable Gel Call battery and two lecture bottles of gas in the power pack-

Jan 1, 1978

By R. A. Vik

The influence of thermal treatments on the grindability of low-grade hematitic iron ores from Michigan and Minnesota was examined in bench-scale tests. Treatment factors were roasting temperature, roasting atmosphere, and ore cooling conditions. Bond ball mill grindability and work indices were used as response indicators in evaluating the condition of the ore. Of the three treatment factors evaluated, roasting atmosphere, which brought about the con version of iron oxides to magnetite, had the most significant effect; roasting temperature had the next most important effect; and cooling condition had the least effect. Optimum grindability was obtained with reduced-quenched products of both ores at 650° C, near the alpha-beta phase transformation of quartz.

Jan 1, 1971

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from ~0.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By Ren G. Dong, Dan E. Welcome

Instrumented handles or dynamometers are widely used to measure hand forces and/or the biodynamic response of hand-arm system. To study hand-transmitted vibration exposure, six generations of instrument handles were constructed or initially developed by researchers in ECTB/HELD/NIOSH. This presentation provided a summary of these handles. Their basic characteristics, limitations, and usefulness are described, which may help their appropriate applications and further improvements. Six Designs of Instrumented Handles Handle 1: The conceptual design is recommended in ISO 10819 (1996)1 for glove test. The grip force is measured by detecting bending strains on a measuring beam in the handle. A special handle fixture was designed to connect the handle to a shaker. Except the screws, the handle and fixture were made from aluminum. Handle 2: The design is based on the principle of shear strain measurement.2-3 Both grip and push forces can be measured simultaneously using this handle. This handle was directly designed for a simulated vibrating tool. Handle 3: This design is basically composed of a handle base, a measuring cap, and two charge-based sensors (Kistler 9212) sandwiched between the base and cap. The handle was also made from aluminum. The fixture for Handle 1 was also used with this handle. This generation of handle has three different handle diameters (30, 40, and 50mm).4 Handle 4: This design is an improvement from Handle 3. The handle fixture was totally redesigned and it was much stiffer than the previous one. The aluminum measuring cap was replaced with a magnesium cap. Handle 5: The basic structure of this handle is the same as that for Handle 3. However, the piezoelectric sensors were replaced with two strain gage based sensors (Interface SML-50). Handle 6: This handle includes two measuring caps, four piezoelectric sensors, and a handle centre base. The handle fixture was the same as that with Handle 4. Methods for Handle Examinations The static and dynamic characterizations were performed using the methods reported by Dong et al.5-6 Results and Discussion Handle 1: The static force measurement depended on the hand grip location on the handle. Its natural frequency was less than 200 Hz.5,6 Because the transmissibility of gloves may not vary significantly with the applied grip force, this handle may be acceptable for glove test. However, the force measurements with this handle may not be reliable. Handle 2: The static force measured with this handle was insensitive to the hand acting location. However, when the handle was vibrating, the force signals could be totally distorted. For this reason, it was not used for vibration studies.

Jan 6, 2006

By Llewellyn A. Rubin

Under Bureau of Mines Contract H0122007, Telcom, Inc., with the assistance of Fenix & Scisson, Inc., conducted a 17-month research and development project aimed at provid¬ing a field-test model of a guidance system for use with the Bureau of Mines Probe Drill. The Probe Drill is a part of the Bureau's Mine Rescue System developed under Contract H0101262. Volume I of this report is subdivided into seven sections. Volume II consists of a number of supporting appendices. In addition, there were delivered under the Contract, a number of other documents which are referenced in the text. Section 1 deals with essential contract information, Program Background, and a general system description. Section 2 covers the project chronology in brief. Section 3 is a digest of design considerations and implementation related to the requirements of the Contract. Section 4 is a description of the System, including illustrations of the hardware, and software. Section 5 is devoted to Operation and Maintenance. Para. 5.1 describes step-by-step field assembly and disassembly of the downhole unit. Para. 5.2 covers Operation. Para. 5.3 covers various aspects of maintenance from the lowest field echelon possible. Higher level maintenance must be accomplished in the laboratory, for the present field-test model. Para. 5.4 covers system calibration. Para. 5.5 covers detailed step-by-step operational sequences. Section 6 covers the results of the field testing, post-test evaluation, and recommendations. Essentially, we conclude that the present hardware (field-test model) has proven every aspect of system performance, but failed to provide reliable assurance of an operationally ready system. Telcom, therefore, recommends a three-phase continuing effort devised to provide the operationally-ready model of the system.

Jan 1, 1973

By George A. Savanick

An experimental hydraulic jetting device intended to operate in a 16-in-diam borehole was designed, fabricated, and used to cut coal and simulated coal samples. This device consisted of two 0.107-in-diam nozzles that rotated in a plane perpendicuIar to a 50-inch length of high-pressure tubing. Experi¬ments were also conducted with stationary jets issuing from a single 0.142-in-diam nozzle. Numerous experiments were performed using systematic variations of jet parameters coupled with assessments of cutting rates. These Bureau of Mines tests showed that when operated at 4,000 psi pressure and a 40-gpm flow rate (1) the device can fragment coal up to a distance of 8 feet from the nozzle, (2) 4,000-psi jets cut more effectively than lower pressure jets with the same nozzle diameter, (3) stationary jets do not cut as effectively as moving jets, (4) interkerf breaking occurs when the kerf spacing is less than 2 inches, and (5) if the kerfs are spaced <1/2 inch, the jet is deflected and thereby reduces cutting effectiveness.

Jan 1, 1975

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first paper5/ dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second dealt with extraction in a mine (Crucible) in which coal was loaded. by hand and in which the rib lines wore long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central hart of Washington County, Pa. , approximately midway between the Montour 10 end Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalizations as appear to be justified.

Jan 1, 1940

By O. C. Blade

Sales of diesel fuel in the United States during the post year and a half have increased greatly. In 1955 over 174 million barrels were sold of which 80 million (or 46 percent), were used by the railroads, and over 44 million barrels (25 ½ percent) of the fuel were used in trucks, busses, tractors, and heavy moving equipment. Vessels (12 percent), industry (9 ½ ), the military forces (4 ½ ), power plants (2), and oil companies (1/2 percent) account for the remainder. 2/ Dally deliveries of diesel type fuel from refineries averaged over 16,750 barrels during the first six months of 1956 in comparison with 15, 250 barrels during the corresponding period of 1955. 3/ Information on the properties of diesel fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1957

By Harvey Patashnick

Current state-of-the-art microweighing technology represented by the Tapered Element Oscillating Microbalance (TEOM) is utilized as the basis for a new generation of Personal Dust Exposure Monitors (PDEM&apos;s). Two design configurations are presented. The first is an end-of-shift analysis system which uses small TEOM-PDEM cannisters that replace the filter cartridges in the current PDEM system. All other components carried by the miner (cyclone preseparator and pump) are the same. After the shift the TEOM cannister is plugged into an interface box which enables a minicomputer to automatically identify the unit, determine the dust mass increase during the shift, compute the shift average dust mass concentration, and print out and/or store the data. The second design is a real-time TEOM-PDEM system which is capable of operation over a 10-hour shift and on demand display real-time dust concentration level, time weighted average, and shift average concentration. As a result of the design study, a prototype end-of-shift analysis system was fabricated and delivered to the Bureau of Mines. A description of this system which consists of six TEOM cannisters, interface electronics and minicomputer is given. The system represents a significant advance in the dust monitoring program in terms or accuracy and automation.

Jan 1, 1983

By R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Dale R. Ralston

This investigation was divided into two major phases. Phase I of the study was an examination of the occurrence and production of acid water within the Bunker Hill Mine in northern Idaho. The second phase of the project involved the study of water movement through an abandoned tailings pile. Mineralogy and hydrogeology were determined to be the two most important factors in the acid mine drainage problem. Low pH water was formed in the mine in areas of lead-zinc ore rich in pyrite. Water movement in the mine was important in the production of acid and the transportation of heavy metals. Areas of recharge to the mine were identified. A data collection network was installed to monitor water quality and quantity changes. The quantity of acid drainage from the mine was found to vary directly with surface runoff events. The study of the abandoned tailings pile was performed to determine the characteristics of water movement through the tailings material and the resultant impact on the hydrologic environment. The Page Tailings Pile, abandoned in 1969, was utilized as a study area. An extensive network of piezometers and meteorological data collection sites were installed in and near the pile. Data collected to date indicate the presence of a ground-water mound under the east half of the pile. Some transfer of ions from the tailings pile to the ground-water system has been detected.

Jan 1, 1973

By Travis Q. Lyday

Mineral production in Fiji, a group of 322 volcanic islands and atolls of Melanesia in the southern Pacific Ocean, continued to be dominated by gold. However, the Fijian mineral sector remained a minor factor as a source of export earnings, Government revenues, and employment, generating only 1% of the gross domestic product (GDP), estimated as $1.2 billion.2 The largest and most important mining operation was the Vatukoula gold mine on the north side of Viti Levu, the main island. The Vatukoula Mine has been in prduction since 1932, producing about 3.8 million troy ounces of gold and 1.3 million troy ounces of silver to date. In April 1983, the large Australian mining firm, Western Mining Corp. (WMC), assumed operation of the mine in a joint venture with Emperor Gold Mining Co. Ltd., which operated the mine previously. The WMC takeover of the mine management was expected to bring in additional capital and technological expertise in order to modernize operations, increasing both efficiency and output. During the year, rate of recovery was only about 75% of the gold contained in the ore and only 40% of the contained silver. Mining at the Vatukoula Mine was done using bath opencut and underground methods, with about 60% of the ore mined attributed to the underground operations.

Jan 1, 1985

By W. L. Acherman

The Bureau of Mines found the chemical and galvanic corrosion behavior of the TZM and molybdenum-30 tungsten alloys to be generally equal or superior to that of unalloyed molybdenum in many aqueous solutions of acids, bases, and salts. Notable exceptions occurred in 1 [N] nitric acid, where both alloys corroded appreciably faster than molybdenum. In mercuric chloride solutions, the TZM alloy was susceptible to a type of crevice corrosion which was not due to differential aeration. The alloys were usually not adversely affected by con-tact with dissimilar metals in galvanic couple experiments, but the dissimilar metals sometimes corroded galvanically. Both alloys were resistant to substitute ocean water spray at 60° C.

Jan 1, 1968

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956