Search Documents

By G. Adachi, K. Machida, T. Ozaki, K. Murase

The chlorination rate with CCl4 was unexpectedly slower than carbochlorination using chlorine under the same reaction conditions. Chlorination with CCl4 was topochemical and the amount of monazite reacted after different periods suggested that the kinetic control step was the reaction between CCl4 and the monazite core at the interface. The kinetic order of the reaction was 0.5. The presence of a complex former, AlCl3, promoted the chemical vapour transport of rare-earth chlorides as complexes

Jun 18, 1905

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

By M. W. Robotham, H Wang

removal efficiency is analysed from a stochastic

Apr 1, 1995

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By Bakker J. de, P. A. Leest, W. L. Dalmijn, H. J. Glass

The test facility at the Delft University of Technology, in the Netherlands, was characterised. Advantages include the possibility of separating particles with high but different densities up to 9 g/cm3, the ease of adjustment to any required separation density and the absence of moving parts. Simultaneous separation of more than two types of particles is possible and the magnetic fluid is safe and convenient to use compared with other heavy liquids. Disadvantages include loss of magnetic fluid with outgoing particles (cost approx US $10/l) and degeneration of fluid due to bacterial activity, reaction with particles and with surroundings. Only non-magnetic materials can be separated, there is limited potential for scaling up and high investment is required on account of the cost of magnets. Future improvements in the design of the apparatus and the properties of the magnetic fluids can only enhance its attractiveness for commercial applications

Jun 18, 1905

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

Discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-90, included written contributions on size and gauge standardisation by Lupton A., Peck W.R., Dean S., Mayer R.W. and Ashworth J., with the author's written response, and by Bulman H.F. and Brown M.

Dec 1, 1916

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

By I. L. Whyte

apparent density and drag coefficient of porous ores on

Apr 1, 1995

By M. M. Cole

An assessment of the combined application of remotely sensed satellite imagery, geobotany and biogeochemistry reveals the complementary value of these techniques in the Thalanga area. The SPOT imagery yields useful information on features of the terrain and discriminates the gossan over the ore zone. Geobotany differentiates geological units and the anomalous vegetation provides visual expression of the surface presence of the ore zone, while biogeochemistry effectively locates its concealed extension below Tertiary sediments and ferricrete

Jan 1, 1991

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991

By J. Temporal

An introduction to the conference material in this issue is given together with the issue contents list, closing remarks by its chairman Dr. J. Temporal, the list of contributors and their companies, and the information that the 26th Sir Julius Wernher memorial lecture had had to be presented by the lecturer's wife, M. Biggart, in his absence due to site problems on the Storebaelt project

Jun 16, 1905

By G. E. Pearse

Reports, discussions, a written contribution and two written replies are presented from 11 sessions on: Safety and compressed air; Ground movements; Geotechnical; Channel Tunnel (2 sessions); Machines; Case histories; Transport tunnels; Case studies; Site investigation; and Undersea tunnels

Jun 13, 1905

A study of the thermodynamic properties of magnesium chloride ammines was carried out with the ultimate objective that the thermal decomposition of the hexammine MgCl2.6NH3 may prove successful on a commercial scale for the manufacture of anhydrous magnesium chloride, which is required for the efficient electrolytic production of magnesium. The experimental data are presented in the form of an equilibrium diagram that aids the understanding of the conditions associated with the thermal decomposition of ammines

Jun 13, 1905

By R. Macleod, G. G. Bursey, T. R. C. Aston, J. E. Gale

In 1991 the problems of water inflow at the mine were addressed by a three-phase study. A three-dimensional finite-element computer code, CFEST (Coupled Fluid, Energy and Solute Transport), was used to model the system of groundwater flow around the mine, allowing assessment of the nature of the hydrological regime and of the various recharge mechanisms and sources of inflow. A regional (111 km2) model was used to simulate conditions of low to average mine inflow and provide boundary conditions for the subsequent local (16.8 km2) model. The regional model produced inflows of 0.26 m3/s and the local model 0.25 m3/s. With the use of constant head conditions to simulate a saturated flood plain along the Gays River and on doubling the rate of surface recharge, the local model produced a maximum mine inflow of 0.255 m3/s, in contrast to a measured peak mine inflow of 0.37 m3/s. The discrepancy suggests that during periods of high river level surface water gains access to features with high permeability, such as sinkholes, that may be connected directly or indirectly to the mine workings. Improved simulation of high inflow conditions can probably be achieved by determining the hydraulic conductivity of the river-bed and flood-plain sediments and modelling known sinkholes as discrete units. Possibilities for controlling the amount of inflow to the mine include sealing the flood plain with dykes, checking regularly for new sinkholes, which should be filled and capped, maintaining adequate mine drainage, and monitoring well levels and pressures on a continuous basis.

Jan 12, 1993

By Schwartz M.

Respect for mining in Botswana is long-standing. This article looks at Africa's most transparent mining regime and some of its ambitious plans. Botswana's mining industry value is forecast to average 5.2% growth from 2014-2018 with solid growth for the diamond sector and acceleration of coal production. Respect for the country's mining regime is maintained in the Fraser Institute 2014 annual survey where Botswana occupies the 26th position of 122 administrations. Botswana's transparency is illustrated by Mupane gold mine near Francistown, Ghaghoo diamond mine in the Gope area and the Morupule coal mine

Mar 1, 2015

By J. H. Chesters

The main, though rarely mentioned advantage, is likely to be the standardisation of best practice and product. In a batch process conditions vary cyclically, but with a continuous process they would, at least ideally, remain the same for long periods of time. The other main advantages of continuous over batch processes are likely to be reduced operating and capital costs, the improved possibilities for automatic control, and more consistent product quality. Recent developments are surveyed for ironmaking and steelmaking with reference to blast furnaces; solid-product and molten-product direct reduction; the trough-type processes of Thring, Worner, the Japanese National Research Institute for Metals and Glinkov; basic-oxygen furnace (LD) variants; spray steelmaking; continuous casting and vacuum degassing; rolling; and coating. Encouragement in the devleopment of continuous processes may be drawn from the way unexpected difficulties, such as trouble with sulphur and refractories, were tackled and overcome to achieve the float glass process

Dec 1, 1971

By Evans E. C.

At first sight, the extinction of a mine fire by the action of some such gas as carbon dioxide would appear to be quite a simple and practicable operation. From a consideration of the theoretical aspects only of the question, it becomes evident that the matter is not so simple as it appears to be at first sight. The fire at the Senghenydd Colliery occurred as the result of the disastrous explosion of October 14th, 1913. This explosion was confined to the west side of the colliery; and as a result the timbers in the main intake on this side were set on fire; but these were soon buried beneath falls, and the tire continued under them. Attempts were made to extinguish it with water, with the aid of chemical extinguishers, and by digging it out; hut these had to he abandoned, and ultimately the fire-zone was sealed off by “ bashings” (stoppings). By December, progress in the decrease of combustion was so slow that it was decided to try the effect of inert gas. The installation, control and operation of the carbon dioxide plant and associated water-gauge are described in detail and conclusions drawn for the extinguishing of mine fires by CO2

Dec 1, 1916

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

By J. K. Brimacombe, F. D. Richardson

Studies have been made of interfacial turbulence occurring in reactions in which indium, zinc and cadmium, dissolved in amalgams, are oxidised into aqueous phases by ferric or mercurous ions. It has been found that this turbulence occurs when the concentrations of oxidising ions in the aqueous phase become sufficiently great. These concentrations are the same as those at which the mass-transfer coefficients in the aqueous phase increase sharply when both phases are stirred by gas bubbles rising through them. The effects of gas flow rate on the mass-transfer coefficients for zinc in mercury have been established, and the oxidation of pure mercury has been investigated. The relevance of the work to processes involving liquid metals is discussed

Dec 1, 1971