Search Documents

By Dhanaji S. Chavan, Thallak G. Sitharam

"It is well known that sites comprising of saturated loose sand undergoes large deformations, due to liquefaction, during seismic shaking. To cope with this, different mitigation techniques such as vibroflotation, deep dynamic compaction, compaction grouting, deep soil mixing etc. have been used in practice. However, as all these methods are costly, a new mitigation technique is required. Air injection has emerged as a new mitigation technique in which air is injected into the saturated loose sand. The introduced air makes the pore fluid mixture compressible and results into decrease in the generation of excess pore water pressure during seismic shaking. This paper reviews the laboratory and field studies performed to investigate the effect of air injection on liquefaction resistance. In addition to this, previous research in the direction of desaturation has evolved different techniques to generate gas in saturated sand. These techniques have also been discussed in the present paper. All the field and laboratory studies have shown that even a slight decrease in the degree of saturation increases the liquefaction resistance significantly.Keywords: desaturation, air injection, liquefaction resistance, pore pressureINTRODUCTIONEarthquake events in the past, caused liquefaction of loose saturated sands at many sites in the world. The consequence of liquefaction varied from small deformations to catastrophic failures such as flow slides, lateral spreading, sand boiling etc. (Kramer, 1996). To reduce the liquefaction potential of such soils, different mitigation techniques have emerged across the world. Some of the most widely used mitigation techniques are vibroflotation, deep dynamic compaction, compaction grouting and deep soil mixing (Idriss and Boulanger, 2008).Yoshimi et al. (1989) found that the liquefaction resistance of partially saturated sand is significantly higher than that of saturated loose sand. Further, Pietruszczak et al. (2003) proposed desaturation of the saturated loose sand as a new liquefaction mitigation technique. It is observed that the liquefaction resistance of sandy soil is enhanced significantly owing to the desaturation caused during construction of sand compaction piles (Ishihara et al. 2003). Over past few years research is being carried out on desaturation of sandy soil and its liquefaction resistance ( Ishihara et al. 2003; Okamura and Soga 2006; Yegian et al. 2006; Yegian et al. 2007; Takemura et al. 2009; Eseller-bayat et al. 2013; He et al. 2013; Marasini and Okamura 2015; Zeybek and Madabhushi 2016). As a result of this, different techniques of desaturation have also emerged. Different studies conducted in this direction and their outcome has been discussed in the section to follow."

Jan 1, 2017

By Luca de Sanctis

The analysis of piled raft foundations in layered soils may be performed by 3D finite elements or by approximate procedures. Among the latter, the code NAPRA (Russo, 1998) is based on the method of the interaction factors and accounts for soil layering by the so called Steinbrenner approximation. A comparison between the results of 3D FEM and NAPRA for some reference layered soil profiles shows that the approximation is fully acceptable for engineering purposes, provided the stiffness of the single pile is properly selected. The interest of the conclusion lies in the fact that the amount of work needed to model a practical problem by NAPRA is but a fraction of that needed by FEM modelling.

Jan 1, 2002

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Gustavo Armijo

Slippery and unstable working platforms spoiled not only by natural weather conditions but also by the effects of the construction process (drilling mud, grout slurry) are among the main sources of hazards. Due to this fact a set of recommendations for execution and maintenance of working platforms are presented in this paper, which is based on a study on this subject that is being carried out by AETESS, the Spanish Federation of Geotechnical Contractors. The main objective of this paper is to establish the basis for the right execution and maintenance of working platforms for geotechnical jobs with the idea of increasing safety and productivity. All the aspects involved in working platform safety are analyzed: ground and equipment characteristics, geometric conditions and working platform maintenance. From this analysis a set of general requirements is proposed together with the necessary specific controls before and after the equipment arrival to the job site. In order to facilitate this analysis some flow charts and tables and specific appendixes for each geotechnical technique are included.

Jan 1, 2006

By G. T. Hong

A numerical model for use in design is developed to predict the stresses and axial and bending displacements in a drilled pier in expansive soils. The prediction is based on the horizontal swelling pressures and uplift forces which act on the side of the drilled pier. The exponential suction envelope with the depth within the moisture active zone is estimated based upon the equilibrium suction, moisture diffusion coefficients obtained from laboratory tests, and minimum suction at the ground surface of the site based on field conditions. The volume change of soil is based on suction variations, soil properties, overburden pressures, crack influences, and the relationship between moisture contents and suctions. Considering the movement active and anchor zones on a soil-pile system in expansive soils, horizontal swelling pressures are formulated using the shear strength of an unsaturated soil and the Mohr?s circle and failure envelope. The movement active zone has two sub-zones in which horizontal swelling pressures are attributed to passive earth pressure failure and suction change in the upper and lower sub-zones, respectively. Horizontal swelling pressures which occur in the anchor zone are assumed to be in the at rest condition. The shear stress generated on the vertical surface of a drilled pier is supported by the nonlinear curves of load transfer versus relative displacement. The axial behavior and lateral bending of the pier in expansive soils are simulated using a beam column approach. The computed axial and bending displacements and stresses are used to provide structural design of the pier. Figures of computed results for typical cases are presented.

Jan 1, 2007

By M. T. Davisson

Pile compression load capacity prediction methods are divided into four categories for purposes of discussing their reliability compared to static load test results. The categories considered are: 1) static analysis, 2) driving formulas, 3) wave equation analysis, and 4) dynamic measurement and analysis. It is concluded that any method of static analysis that works for the geological deposit in question may be satisfactory. However, any given method can be quite wrong when applied to other deposits of soil that are different in terms of their engineering and geological characteristics. Dynamic formulas are found to be theoretically unjustifiable. The ready availability of the wave equation analysis for microcomputers eliminates the need to utilize dynamic formulas. The wave equation analysis is found to be the best analytical method for making predictions both for design and for construction control. Dynamic methods of measurement and analysis are found useful, but have limitations that have caused troubles on many projects. Two case histories are presented that show the limitations of dynamic measurement and analysis, and of the wave equation analysis. Soil deposits exist that defeat both the wave equation and dynamic measurement techniques; static load tests are currently the only method of proving the load capacity of piles in such soils.

Jan 1, 1991

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By Raffaella Granata, Wesley Schmutzler, Matteo Bertoni

"The Lower Wood River Levee system, at the confluence of the Wood River Creek and the Mississippi River, in East Alton, Illinois, has been plagued with underground seepage and, in 2010, remediation was deemed necessary by the Southwestern Illinois Flood Prevention District Council and the United States Army Corp of Engineers (USACE). The experts enlisted by the council produced a design that provided for constructing a cutoff wall approximately 2,000 feet long and up to 140 feet deep, through alluvial and outwash soils, and embedded in bedrock. This paper will describe the challenges faced by the Quality Control (QC) and Quality Assurance (QA) teams due to the complex nature of the project in conjunction with an extremely thorough QC/QA program.INTRODUCTIONThe “American Bottom” is an area of 453 km2 (175 square miles) in Southwestern Illinois, extending from Alton south to the Kaskaskia River, which is home to 156,000 people. In the 1940s and 1950s the U.S. Army Corp of Engineers (USACE) designed and built a 120 kilometer (74 mile) long levee system to protect the area from a 500-year flood event on the Mississippi River, which flows through it. The levee system has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed.The Southwestern Illinois Flood Prevention District Council (SIFPDC), to obtain Federal Emergency Management accreditation, in June 2010 commissioned a team lead by Amec Foster Wheeler for the design and management of the required levee improvements. The team presented in 2011 the project’s first set of drawings showing proposed design features throughout the levee system. The project was subdivided in four areas, based on the controlling levee districts, one of which, the Wood River Drainage and Levee District, was split into three subdivisions: Upper Wood River, East-West Forks of Wood River, and Lower Wood River.The project included the installation of a cutoff wall at the confluence of the Wood River and the Mississippi River in East Alton, IL (Fig. 1). The Engineer of Record (Amec Foster Wheeler) considered the cutoff wall as the only viable solution to stop the severe under-seepage that was undermining the integrity of the Lower Wood River Levee. The Lower Cutoff Wall (LCW) project is the subject of this paper."

Jan 1, 2017

By Mark DeSalvatore

Currently, at Caltrans, the Office of Structure Design is carrying out an extensive seismic retrofit program involving transportation structures throughout California. The goal of the retrofit program has been to upgrade existing transportation structures to meet the present seismic codes and anticipated loads that are generated during a seismic event Part of the retrofit program involves retrofitting existing structure foundations when required. To determine if the foundations of a specific structure need to be retrofitted, an engineering analysis of the existing foundations has to be done. If the engineering analysis of the structure foundations determines that the foundations will not meet the load carrying demands required by the structural engineer, the existing foundations are then retrofitted. The retrofit projects that require foundation modifications can be separated into two general cases. The first case comprises structures where the original designs will not meet the demands of the present seismic design code. In this case, the existing foundations are not capable of providing the load capacities the current seismic code requires. The second case consists of structures where the retrofitting of the superstructure will increase the required load carrying capacity of the existing foundations during a seismic event In this case, the anticipated load demands on the existing foundations are greater than the foundations are capable of providing. For either of the cases listed above, the present strategy for increasing the capacity of the existing structure foundation consists of installing tiedown anchors or large capacity piles to provide the required resistance to seisraically induced loads.

Jan 1, 1993

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By Joel Moskowitz

A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140 m by 100 m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8 m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8 MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations the seam dipped below more competent rock. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half.

Jan 1, 2002

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Amaneh E. Kenarsari

Among the different sources of uncertainty in pile bearing capacity prediction including inherent heterogeneity, measurement and model uncertainties, the inherent heterogeneity of soil properties is of particular interest and is considered in this study. Cone tip resistance data are utilized to calculate pile bearing capacity by considering vertical soil variability. In this regard, cone tip resistance component of CPT data is assumed as a random parameter. Realizations of this parameter are achieved with the aid of local average subdivisions and random field theories. Monte Carlo simulation is used to generate different realizations of CPT or CPT-u data. Pile bearing capacity was then calculated by the use of direct method. Pile bearing capacity are predicted for a project in south of Iran using this method and probability density function for the total bearing capacity of pile is plotted. Coefficient of variation of 33% for ultimate bearing capacity shows the variability of bearing capacity due to variation of soil strength in depth. Cumulative probability chart for the ultimate bearing capacity are plotted as an efficient tool for estimating ultimate bearing capacity of piles with different desired confidence levels for vertically variable soil strength properties. Significant difference between mean value of pile bearing capacity (18 MN) and limit with 95% confidence level (8 MN) emphasizes the importance of considering soil variability.

Jan 1, 2011

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity. Now this important project is in progress and this report describes the special foundation techniques used on the great ship lock Hohenwarthe. Hohenwarthe is a double- bay ship lock of considerable scale, which is notable for recirculating water rather than letting it flow. It includes 44 800 m2 ( 481 720 sq. ft) of up to 55 m ( 180 ft) deep cut- off walls, ground water control, 1248 bored piles with a depth of 22 m ( 72 ft ) serving as foundation and 28 000 m ( 91 864 ft) of soil densification with vibroflotation equipment for ground improvement. In the year 2003 the project shall be completed and all ships can travel from the West to the East through Germany without expensive and time- consuming detours through other canals and locks.

Jan 1, 2000

By V. M. Troughton

Large diameter bored piles with grouted bases have been adopted for the foundations of the majority of the buildings at Canary Wharf in London's Docklands, including a deep basement car park. The piles are founded in the Thanet Sand which forms part of London's aquifer where water levels are reported to be slowly rising. A special pile test has been carried out to determine the effects of both the basement excavation and a possible long term rise in the groundwater level on the performance of base grouted piles. These effects were simulated by injecting water around the pile toe and thus reducing the vertical effective stress. In this paper the test layout and procedures are described and the results are presented. The test results showed that the reduction in pile base resistance under increased water pressures was less than predicted by conventional design methods based on vertical effective stress. The end bearing resistance was found to be proportional to the mean effective stress.

Jan 1, 1989

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018