Search Documents

By Pierre Gouvin

This paper describes the design, installation and monitoring of a state of the art real time geotechnical/structural instrumentation monitoring system to facilitate tunnel construction under Interstate route I-5 in Seattle, Washington, USA. The project involved removal of existing highway foundation substructures on both North and Southbound lanes as well as the underground reversible high occupancy vehicle lanes. The system utilized state of the art 3-D pulsed laser scanning, wireless sensor networks, automated robotic total stations, tilt beam sensors, narrow angle tiltmeters, and in-place inclinometers. Dedicated real time data loggers, with a web based graphical interface, provided 24/7 access to critical measurements. In addition to the instrumented sections of wall and roadway subsurface which monitored physical measurements at known points, the pulsed laser scanning allowed complete site monitoring coverage where physical sensors were not located. This data allowed post processing at any location enabling the contractor and designer to respond to unforeseen structural responses to construction. Use of the instrumentation system resulted in the early detection of wall movement, and provided feedback to the designers to facilitate construction process changes in order to minimize further movement.

Jan 1, 2010

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By Bernhard Bruggaier

Outside the oil and gas industry there is an increasing demand to install big piles for the foundation of ports, bridges, and wind-energy plants. This article introduces the design and techniques in using large MENCK pile driving hammers to install big foundation piles. Piles with a length up to 120 m, an outside diameter of 1.0 m to 3.15 m and weighing between 25t and 400t are being driven for these types of foundations. The required energy lies between 200 and 1700 kNm. Pile driving hammers that bring this amount of energy weigh from 38 to 300t and have a length between 10 and 20 m. Handling these big pile driving hammers requires a crawler crane on land or cranes on floating pontoons or jack-ups when working in water. Possible are either vertical or inclined piles, using a leader for inclinations up to 1:1.7 or up to 1:3 in a free riding version. Project descriptions demonstrate the versatility and practical use of the equipment under diverse operating conditions.

Jan 1, 2002

By A. Flora, E. Bilotta, F. Foria, V. Nappa

"All the typical applications of deep mixing rely on the good mechanical properties of the improved columns to strengthen or stiffen the ground for a number of geotechnical applications.This paper focuses on a completely different kind of deep mixing, carried out in order to obtain columns much softer than the surrounding soil. This kind of deep mixing, named Soft Deep Mixing (SDM), is introduced as an original means to tackle seismic risk, and can be convenient when the existing structure to be protected has a historic relevance that cannot be altered with structural modifications. The idea is that properly assembled layers made of partially overlapped SDM columns, with dynamic impedance much smaller than that of the surrounding soil, will filter and reflect most of the seismic energy.The paper presents the results of some 2D parametric numerical analyses aimed to investigate the seismic performance of this innovative approach. Simplified dynamic inputs (Ricker wavelets, having only one largely predominant frequency) were adopted to better understand the effect of signal frequency. The analyses show that the effectiveness of the soft grouted isolating barrier depends on soil and SDM geometrical, physical and mechanical properties, as well as on the frequency content of the seismic input.INTRODUCTIONPassive structural systems installed at the foundation level of existing buildings are a common solution to protect them against earthquakes. However, installation procedures are expensive and not always feasible, as for instance in the case of valuable buildings. As an alternative, ground improvement techniques can be used to modify ground properties, in order to mitigate the intensity of shaking at ground level. The propagation of shear waves in the ground can be modified by introducing a layer of artificially modified material, having a dynamic impedance (defined as n =p VS, where p is the material density and VS the velocity of shear waves) very different from that of the natural soil. Both very high or very low values of the dynamic impedance of the grouted soil (nt) can be effective in reducing the overall transmitted energy, with the difference that – for a given reduction of the transmitted energy - stiff grouted layers tend to filter the low frequency components of the amplitude spectrum without modifying in a significant way the high frequency components, while soft grouted layers have the opposite effect. Then, ideally the choice of the best grouting technique should be made considering the effects of the different frequency components on the building to be protected. These effects are detrimental for the structure when they are close to its natural frequency: high frequency components result into large structural loads on massive squat structures (high natural frequency), and low frequency components may be critical for tall and flexible structures (low natural frequency). Therefore, the typical procedure of stiffening the uppermost soil layers regardless of the kind of building to be protected is not necessarily beneficial, and for the case of squat structures soft grouting should be preferred. However, this procedure has not been taken into account yet in the engineering practice, and may pose static problems at ground level (i.e. excessive static settlements)."

Jan 1, 2015

By Artak D. Mirzoyan

Pile foundations near the edge of a slope are often required to resist lateral loads. This is particularly important for piles at abutments of bridges. However, very few full-scale tests are available that compare the effect on lateral resistance of piles installed in sloping ground to piles installed in horizontal ground. To investigate the effect of a slope on lateral pile resistance, three full-scale lateral load tests were performed on an instrumented steel pipe pile. For the first test, the pile was laterally loaded in horizontal ground; in the second test, the pile was at the crest of a 30º downward slope; and for the third test, the pile was located three pile diameters from the crest of a 30º slope. The soil around the pile consisted of well-graded clean sand (concrete sand) and was compacted to 95% of the modified Proctor maximum unit weight in all three tests. Lab and in-situ direct shear tests indicated that the friction angle of the sand was approximately 39 degrees. The pile was instrumented with strain gauges so that the bending moment versus depth profile could be determined. Pile head load, deflection and rotation were also measured. Based on the load versus deflection curves, the presence of the slope resulted in a decrease in lateral resistance of about 20% for the pile at the crest of the slope and 8% for the pile at 3D from the crest of the slope relative to the pile in horizontal ground. The presence of the slope also resulted in an increase in the maximum moment of 29% and 20% for the piles at the slope crest and at 3 pile diameters from slope crest, respectively. Analyses using LPILE with the measured friction angle significantly underestimated the lateral resistance for the horizontal soil profile. After calibrating the model with the response of the pile in horizontal sand, analyses including the slope still underestimated lateral resistance by about 20%.

Jan 1, 2007

By Nabil F. Ismael

"Load tests were carried out to examine the ultimate bearing capacity of short, large diameter bored piles in connection with the construction of a multistory building on the Arabian Gulf in Kuwait. Testing included 0.45 m, 1.0 m, and 1.2 m piles installed through loose sand into a bearing stratum consisting of very dense cemented sands. All tests were carried out to failure. The base resistance and shaft friction were calculated using the Meyerhof method for a layered soil profile. The method employs the standard penetration test N-values. The results indicate that the piles are end bearing piles with a great portion of the pile capacity due to base resistance. The mobilized skin friction is small. The calculated pile capacities were very close to the measured values with the maximum difference not exceeding 10%.INTRODUCTIONShort, large diameter bored piles are used with increasing frequency for heavy structures in Kuwait, and the Gulf region where ground conditions indicate loose deposits of calcareous sands. The piles range in length from 8 m to 15 m with their base located in the dense-to-very dense, cemented sand bearing deposit. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on large diameter bored piles installed through loose calcareous sands into dense-to-very dense cemented or partially cemented sands are very limited at present. The results of three load tests carried out recently on bored piles at one site in Kuwait have become available. In these tests the failure load was either reached or can be extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers.This paper presents the soil conditions, pile installation details, and the pile load test data at the test site located in Shuwaikh, Kuwait. The site is facing the Arabian Gulf. Test results were directly analyzed and the point resistance, and skin friction were calculated. The ultimate capacities of the piles were calculated and compared with the measured values. The influence of the pile diameter on the settlement at ultimate and at working loads is examined"

Jan 1, 2017

By Patrick J. Lydon, Gregory A. Terri

"The recently opened Mansueto Library at the University of Chicago campus was a 2012 OPA runner-up. The dramatic elliptical shaped dome of this structure tells only part of this structure’s story. The underground automated storage and book retrieval system below ground required excavations as deep as 55 ft (17 m). The system that allows the University to store many of its publications well below grade also required an approximately 50 ft (15 m) clear span for the perimeter walls between the lower level and street level slabs. The latter requirement allows the conveyors to operate freely to retrieve and transport publications up to the lobby level. The design-assist-build team worked together to develop the most cost-effective solution for below-grade work in this challenging urban and geologic environment.The perimeter of the new oval-shaped library is over 620 ft (189 m) long and sits in a central location on campus—adjacent to the Regenstein Library and two city streets and the Henry Moore sculpture, which commemorates the location of the first self-sustaining controlled nuclear reaction. The new library construction not only had to meet challenging structural and geotechnical requirements, but also had to be sensitive to its active and historic surroundings. The soils at the site consist of about 25 ft (7.6 m) of sand, followed by lean clay, generally increasing in stiffness to the top of the dolomitic limestone. Five to 10 ft (1.5 to 3 m) pockets of saturated sand also lie on the north side of the site at about 45 ft (13.7 m) below grade. The top of weathered rock varies in elevation from 59 ft (18 m) below grade in the south to 69 ft (21 m) in the north. There is 1 to 2 ft (30 to 60 cm) of weathered rock. Groundwater at the site is about 7 ft (2 m) below grade.The new structure would extend 55 ft (17 m) below grade through saturated sand strata and into weathered rock for part of the structure’s footprint, so it was critical that the new permanent retention system minimize groundwater seepage laterally through the structure’s wall as well as piping through the weathered rock below the structure. The perimeter walls had to be very stiff to minimize ground movement around the structure’s perimeter due to the significant clear span between slabs."

Jan 1, 2013

By Wei Tu

A grade separation was required to allow uninterrupted traffic crossing for a busy rail spur and a county road. The grade separation was achieved by creating a 30-foot (9-meter) high embankment that incorporates two multiplate tunnels and allows the passage of a rail spur and an existing county road. The site is located in an abandoned meander channel in the floodplain of the Mississippi River, near Osceola, Arkansas, and is underlain by more than 40 feet (12 meters) of soft clay and interlayered clays, sands and silts. Without soil improvement, the post-construction settlement would exceed 3 feet, slowly crushing the proposed tunnel structure and cutting off the railroad. Preloading, combined with vertical drains, was used to accelerate the consolidation of the underlying soil layers and to reduce the post-construction settlement under working loads. Six settlement plates were installed to monitor the progress of consolidation under surcharge load. The Asaoka observational method and the hyperbolic fitting method were used to analyze the measured settlement data to predict the end of primary settlement. The in-situ consolidation coefficient, ch, was back calculated from the measured settlement data. The stress release caused by the removal of the preloading surcharge load and the tunnel installation was determined using a Plaxis 3-D finite element model. The measured and predicted settlement using Hansbo's analytical solution demonstrated reasonable agreement. Early removal of the surcharge and construction of the tunnel prior to reaching the end of primary settlement was accomplished by analyzing the post-excavation stress reduction achieved via tunnel construction.

Jan 1, 2009

By Wayne S. Smith, Erik James, Jose R. Gomez

"Soil mixed seepage cutoff walls are increasingly being used in levee and dam modification projects nationwide. An important aspect of their overall quality depends greatly on the language included in the specifications. Depending on the method (e.g. vertical axis auger mixing, cutter soil mixing, or trench mixing techniques) the specifications are a blend of prescriptive and performance based contract language with differences in element construction, element connections, quality control/quality assurance, and work area restrictions. Many of the existing specifications were initially developed by contractors in whole or in part, and can contain restrictive provisions favoring the authoring contractor. In response to these challenges, basic soil mixing fundamentals were revisited and recent lessons learned incorporated, resulting in the development of a new specification for soil mixed seepage cutoff walls that provides adaptability for the various construction methods. The new specification addresses quality control, quality assurance, equipment independence (elimination of restrictive contract language), rig instrumentation.INTRODUCTIONSoil mixing has been used in the construction of seepage barriers for over 30 years. Most soil mixed project primarily use the wet-rotary-shaft, wet-rotary-end or wet-vertical panel methods (reference FHWA Deem Mixing Manual Figure 137). One of the first major soil mixing seepage barriers was constructed in the Jackson Dam in Wyoming. Since then the use of soil mixing for seepage barriers has increased significantly and this specialized domain of construction which was solely procured by RFP methods, is now increasingly being specified in projects issued for bid. The Bid documents require more careful specification writing than RFP methods because the RFP methods allowed detailed proposals by the contractor. Therefore the development of soil mixing specifications began with contractors preparing the specifications. This paper addressed some of these issues, and proposes methods to address these resulting concerns. The resolution of these issues considers several aspects: 1) Assessment of binder injection, 2) Evaluation of mixing index, and 3) Verification testing."

Jan 1, 2016

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By Tim Siegel, III Fondren, Billy Camp

"INTRODUCTIONThe new $650 million power block at Santee Cooper’s Cross Generating Station in Cross, South Carolina is being constructed on driven pre-stressed concrete (PSC) piles. S&ME, as geotechnical subconsultant to Parsons Energy and Chemical Group, was responsible for pile analysis and design to meet the site’s geotechnical and seismic challenges. Selection, analysis and design of the PSC piles included consideration of the following:• Column and equipment support loads ranging up to 500 to 1000 kips (2224 to 4448 kN).• Incorporation of the 2000 International Building Code seismic provisions.• A thick upper soft clay and loose, liquefiable sand.• Potential for karst-related features in the calcareous Santee Limestone.GEOTECHNICAL CHARACTERIZATIONThe near-surface site geology consists of (in order of increasing depth): (1) Pleistocene sediments, (2) the Santee Limestone (considered part of the Orangeburg Group) of Eocene age, and (3) the Black Mingo Formation of the Eocene/Paleocene age (refer to the shear-wave profile in Figure 4). Pleistocene clays and silts are generally soft and will settle significantly if subjected to loading by heavy grade-supported structures while the interbedded sands are generally loose. Where submerged below the shallow groundwater table, the sands were determined to be liquefiable during a strong earthquake.The Santee Limestone is a nearly white to yellow fossiliferous and partly glauconitic rock consisting chiefly of calcium carbonate. Observations of the rock core samples from the site indicate that it can range from hard crystalline limestone (primarily in thin layers) to a lightly cemented sand. In terms of rock strength, the Santee Limestone is generally very soft to soft, depending on the cementation and other depositional characteristics."

Jan 1, 2004

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By George J. Tamaro

In 1967 the Port Authority of New York and New Jersey undertook the construction of the World Trade Center (WTC) diaphragm walls, installation of the lateral support system and the excavation of the site, commonly referred to as the "Bathtub". The work took two years to complete. In 2001 the City of New York undertook the re-excavation of the site after the terrorist attacks. The recovery work will take eight months to complete. This paper describes the initial work on the WTC "bathtub" in the late 1960s and the recent work during the recovery.

Jan 1, 2002

By Christopher Sammon, Nicholas Turus

"The demand for underground parking in South Florida has increased as a result of changes to the local building code, coupled with developers’ desire to improve building aesthetics and provide much needed walk in retail space for high-end structures. Historically, underground construction was uncommon in South Florida due to the high groundwater level and porous soil/rock. Conventional dewatering methods become ineffective only a short depth below the ground surface and deeper excavations have required a tremie seal solution consisting of wet excavation and the pouring a temporary unreinforced slab under a water head. However, as excavation area and depth increase, the cost and schedule of the tremie seal method become problematic. For these reasons developers and construction teams alike have looked to contractors in South Florida for alternative means of construction.This paper details the construction of two sites in South Florida where Deep Soil Mixing (DSM) technology offered an efficient alternative to tremie seal construction. The Brickell City Centre required excavation of 8 acres to depths of 30 feet, and augercast piles up to 36” diameter and 110 feet in depth. The second site, Jade Signature, required an excavation of up to 41 feet directly adjacent to the Atlantic beachfront. Due to the concerns over differential settlement, the project featured a soil mixed gravity wall that was designed and installed to allow for completion of the tower prior to excavating the adjacent garage.Both projects involved improving every square inch of ground beneath the planned project excavation. The developed DSM seal slab solution creates a nearly impervious excavation at excavation invert with the strength to resist hydrostatic uplift forces. Low permeability site perimeter walls are constructed to complete the sealed excavation and reinforced with either beams or sheet piles for structural support. Augercast piles required for the permanent hydrostatic concrete slab supplement the uplift capacity of the DSM. After DSM and augercast piles are installed from grade, the site is excavated in dry conditions."

Jan 1, 2017

By Jonathan G. Cannon

"This paper will describe dynamic pile testing conducted during installation of driven octagonal precast prestressed concrete piles used as the foundation for this bridge. The piles were long and hence spliced. A number of the piles showed damage near the splices and the damage location was near the ground surface so that the damage could be verified using visual inspection. The piles and splice configuration are still in use today without modification. Further WEAP driveability analysis has been conducted which demonstrates the effect of the splice on pile stresses and a likely failure mode. A slight modification is proposed to the splice that should prevent the damage on future projects.INTRODUCTIONThe bridge site is located on the Olympic Way, Route 41, about 20km north of the regional centre of Albury, NSW. For a long distance north of the site the Olympic Way ""shadows"" the main Melbourne to Sydney rail line and is located on the Western side and in close proximity. At the bridge site there was previously a sharp dog-leg in the road and a right angle level crossing with the road changing to the Eastern side of the rail line, eventually joining up with the Hume Highway, which in turn now becomes a ring-road through the eastern outskirts of Albury. The dog-leg and rail crossing had warning signs and bells, speed restrictions and rumble strips to warn approaching motorists to reduce speed. Site distance was exceptionally good.Approximately 2years before construction a group of five ""high spirited"" young men from the local area were driving south on the Olympic Way adjacent to a south-bound train. It is understood they interacted with the train crew for a period of time. Unfortunately the car and train collided at the level crossing and all of the young men were killed. There were outpourings of grief in the local community and a decision was made to replace the level crossing with a road-over-rail bridge.The bridge was highly skewed with two piers and two high level abutments with fill embankments on both approaches.GROUND CONDITIONSThe site is open grazing country with approximately level ground at the site with surrounding low hills. The geology was unremarkable with consistent stiff clays for a considerable depth.The design required driven precast prestressed pile foundations with the piles to be driven to a considerable depth.Hard driving with high tension stresses were evident from the start of driving and a variety of different pre-bore lengths were adopted in an attempt to minimise driving and potential for damage. At the abutments the pile locations were predrilled for at least the full embankment depth.PILESThe piles were 550mm octagonal prestressed concrete with the pier piles being single piece and the longer abutment piles being two-piece with a ""standard"" epoxy glued box splice. Pier piles and the initial length of the abutment piles were 24m. The add-on piece used at the abutments was 12m. Pile concrete was grade 50MPa."

Jan 1, 1900

By Racquel Nottingham, Freddy Lopez, Ole Gadermann

The ongoing urban development is a global phenomenon, placing has high demands on urban infrastructure (housing, public services, transportation, telecommunications, etc.). Micropiling is one of the most successfully implemented deep foundation technologies in urban interventions, and in densely populated and built-up areas. The use of micropiles enabled the implementation of several solutions within short time frames, with minimal disturbance to the daily activities of the population. Since urban interventions usually represent a very important investment and have an economic impact, special attention should be paid to the serviceability of the urban infrastructure in the middle and long term. For the foundations, the design loadbearing capacity of the used structural elements needs to be guaranteed during the planned life time of the structures. In the case of micropiles, it must be ensured that the steel load bearing elements are effectively protected against corrosion. This paper presents the structural design of permanent self-drilling micropiles, subject to tension due to uplift loads. For the case study, different micropile systems - available worldwide - will also be evaluated. For the afore mentioned micropile systems, the design considerations regarding the durability of the reinforcement, based on their corrosion protection approaches, will be presented in this paper.

By Andreas Massarsch

Information Technology, IT, is rapidly affecting all aspects of private life and how professional activities are conducted. Probably the most important development is the Internet, which makes it possible to exchange information independently of time and geographic location. While traditional communication is based on limited availability to information, the basis of the new Information Technology age is abundance and unlimited access. IT has evolved into a powerful resource and new applications are being developed and introduced almost daily. IT influences every aspect of our private life as well as our business environment. If properly used, IT can become an important resource for planning and implementing construction projects more efficiently, at lower cost and with higher quality. Interactive Web Platforms are already being used for group collaboration on a global scale. As these can be used without programming knowledge and are user-friendly, Web Platforms make cooperation more efficient and stimulate members to actively participate. Another application of growing interest are Internet Platforms and electronic publishing, which can provide technical and other information in different formats and much cheaper than conventional books or proceedings.

Jan 1, 2002

By Barry C. Roth

A Real Time Automated Remote Reading Electrolytic Tilt Monitoring System was effectively deployed for monitoring an existing five story brick building during underpinning, shoring and excavation operations for a directly adjacent thirty-foot deep excavation. The monitoring system was comprised of four sets of uniaxial electrolytic tilt meters connected to a Campbell datalogger with multiplexer, cellular modem and solar power. The excavation was for the foundation and underground parking as part of a new 55 story tower complex. Challenges to the contractors and to our monitoring personnel which were addressed included a tight urban site contemplating property line to property line new construction with directly adjacent old existing buildings, buried concrete foundations from former site use, cohesionless pervious sandy soils and high groundwater. Highly variable and diurnal ambient temperature regimes due to adjacent building shadows required careful corroboration and application of temperature corrections to the raw data. Earth tides were suspected on a very small scale and investigated by correlation between the data and the local sinusoidal tidal ephemera. Incidental inadvertent contractor interference with the instruments during underpinning due to site constraints was readily detected.

Jan 1, 2007

By Tsunenobu Nozaki

"Basically, the “Press-in Piling Method” was invented to eliminate construction nuisances, such as noise and vibration which have been serious unsolved problems for advancing societies over a long time. In the construction industry, piling works have been a major cause of noise and vibration, because most piling methods utilize dynamic load to install piles into the ground. The secret of the Press-in Piling Method is to utilize static loading to install pre-formed piles rather than dynamic load. The piles are hydraulically gripped and jacked into the ground by the special piling rig known as the “Silent Piler”. Therefore, the piles can form a robust and firm foundation, which is another advantage of the Press-in Piling Method.The Press-in Piling Mechanism and Implant Foundations The basis of the Press-in Piling Method is simple. The Pres-in Piling Machine installs a preformed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles, which are called “Reaction Piles”. Due to this, the Press-in Piling Machine can produce a powerful piling force whilst only requiring minimal machine size.With the Press-in Piling Method, as piles are pressed into the ground, they are incorporated with the surrounding soils, which provides a large bearing capacity and passive horizontal resistance. These embedded foundations which are firmly anchored into the ground are known as “Implant Foundations”. Being embedded into the ground, the foundations are resilient and maintain their serviceability even in the worst credible design conditions."

Jan 1, 2015