Search Documents

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By D. Lopez, D. L. Doerr, T. J. Drake

Automated scanning electron microscopy has been widely used in recent years for gold and other precious metals characterization. However, application of this technology is resource intensive and in most instances needs specialized technical personnel to process the samples and information. Newmont Metallurgical Services (NMS) has recently acquired an ASPEX SEM. The ASPEX SEM offers some significant benefits/improvements in sample preparation and sample processing time. NMS and ASPEX have been working together to develop an approach utilizing this technology for the minerals processing industry and specifically for gold characterization.

Jan 1, 2011

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013

By John A. Legge Jr.

"ACCOMPANYING Alberta's great natural endowments of oil, wheat, scenery, fishing, and hunting is also a generous endowment of geophysical problems to plague the interpreting geophysicist. These problems — by no means unique to Alberta — are sufficiently numerous and outstanding to be of major concern in exploration. Some of them have been adequately solved, others are well on their way to being solved, and still others remain almost completely unsolved. Often a problem readily solvable in one area can be solved only with great difficulty in another. Many are closely allied with the geological conditions and require the best co¬ordinated efforts of the geologist and geophysicist for their solution.It is a fairly general practice to study rather carefully the geophysical characteristics of known producing reefs in order to obtain data on which to base an interpretation of unproven areas. This practice obviously has a very sound basis, for, as discoveries become more and more widespread in the Alberta basin, it is found that the variation' in geological conditions has a marked effect on the seismic results, as would be expected. By carrying this analysis over an area it is possible more and more to anticipate the geophysical picture which should be obtained in connection with reefing under the varying geological conditions. Another phase of this procedure, and one that has received less attention, though it is certainly of importance, is the analysis of the all too numerous failures. A study of these failures may be more fruitful than a study of the successes for it may indicate weaknesses of field procedure, computations, or in¬terpretation not particularly obvious in the discovery areas. These studies must not only include the geophysical characteristics of the observed `anomalies', but should also be coupled with a thorough geological study to ascertain whether some unanticipated geological condition is responsible for the erroneous geophysical interpretation."

Jan 1, 1953

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By S. Nakamura, K. Fujiwara, S. Hirosawa, S. Tsukamoto, Y. Koshino, Y. Aruga

"In this study, hardness test, differential scanning calorimetry(DSC)and transmission electron micros copy were carried out to investigate the age-hardening behavior of Al-Mg-Si alloy with a Mg+Si concentration of 1.5mass%, and a Mg/Si ratio of 1.0. Pre-aging treatment was conducted for the solution-treated and then water-quenched specimen at 100, 80, 60, 40, 20 (natural aging), 0 and -20°C for 20min or 5h, followed by artificial aging at 170°C for 20min. It was found that when pre-aging time is prolonged from 20min to 5h, the bake-hardening response is deteriorated irrespective of the pre-aging temperature. In particular, the specimens subjected to pre-aging at 20-40°C for 5 h hardly increased the hardness with the subsequent artificial aging. From the results of DSC measurement, it was suggested that as pre-aging temperature is lowered, the amount of solute clusters formed during pre-aging, i.e. Mg-Si clusters and Si-rich clusters, is decreased, but the ratio of Si-rich clusters is increased, resulting in the deteriorated bake-hardening response.INTRODUCTIONIn recent years, Al-Mg-Si alloys have been widely used forautomotive body panels due to their excellent characteristics such as high strength-to-weight ratio and good formability. Their strength is increased not only by artificial aging during paint-bake treatment; i.e. “bake-hardening”, but also when kept at room temperature(RT);i.e. “natural aging”, in association with the suppressed bake-hardening response. Such a “negative effect of two-step aging” has been a serious problem because Al-Mg-Si alloy coils are unavoidably maintained at RT in the manufacturing process of body panels; e.g. shipping and storage. However, it was reported that pre-aging above 70°C before the two-step aging can restore the bake-hardening response, and such an improvement is related to the formation of solute clusters(Sato, 2006; Abidet al., 2010; Takaki et al., 2014; Zandbergen et al., 2015). From the comprehensive analysis by three-dimensional atom probe (Aruga et al., 2014 and 2015), it is believed that Mg-Si clusters formed during pre-aging transform into the strengtheningß"" phase, whereas Si-rich clusters formed during pre-aging act as a detrimental precursor of ß""phase. In this study, it was aimed to investigate the effect of pre-aging conditions, especially pre-aging temperature and time, on the formation of solute clusters during pre-aging, in order to elucidate the mechanism of the age-hardening behavior of an Al-Mg-Si alloy."

Jan 1, 2018

By D. R. BUDINSKI

Clinton Creek Mine in west-central Yukon produced 0.94 million tonnes of fibre from 15 million tonnes of asbestos ore between 1968 and 1978. The mine closed in 1978. The deposit lies along the margin of a medium sized ultramafic pluton that intrudes schistose and gneissic rocks of the Yukon Metamorphic Complex. Country rocks are metamorphic equivalents of a mixed sedimentary and volcanic assemblage deposited during Precambrian or early Paleozaic time. Movement along the north west-trending Tintina Fault System probably caused the fairly high meromorphic grade that altered the original rocks to schists and gneisses. The ultramafic pluton hosting Clinton Creek Mine is one of several bodies that were emplaced along a deep seated imbricate fault system parallel to the Tintina Trench. Most of rhe intrusions were hydrothermally altered to serpentinite, bur apparently only the one at Clinton Creek contains commercial quantities of asbestos. The Clinton Creek pluton was probably injecred slowly at relatively low temperatures into the crustal rocks as a "mush" that cooled gradually, allowing sufficient time for serpentinization and chrysotile fibre crystallizarion.

Jan 1, 1984

By Palaniappan Chidambaram

Despite the advances in processing technologies, construction techniques, inspection methods, and materials, the number of process safety incidents are still increasing, and often the same types of incidents are being repeated. While regulators are enforcing stringent requirements in regards to safety management systems, process safety incident statistics reflect a failure in effective implementation. Upon closer look at the implementation of safety management systems, it becomes evident that the systems were not built on robust risk recognition. The risk-based implementation approach enables facilities to develop systems focused on managing specific risks and quickly gain momentum and confidence to take next steps towards implementing comprehensive systems. This paper will cover the importance of risk recognition and governance, risk based implementation and the role of Process Hazard Analysis in managing operational risks through the lifecycle.

Jan 1, 2014

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By Joey R. Kish, Shooka Mahboubi, Hatem S. Zurob, Gianluigi A. Botton

The kinetics of the Cr2O3-based scale oxidation and volatilization were studied in the presence of water vapour (H2O). A commercial Cr2O3-based scale forming Type 310S stainless steel was examined at the ambient pressure (0.1 MPa) and 550ºC in relatively low and high H2O containing environments of air- 10% H2O and air- 70% H2O, respectively. The increase in the partial pressure of H2O (pH2O) from 10% to 70% resulted in transition of the oxidation and volatilization kinetics from the parabolic rate law for air-10% H2O to the paralinear rate law for air-70% H2O. The kinetics transition was attributed to the increase in the Cr loss rate from the base scale after coupons exposure in air- 70% H2O. The significant role of the Mn alloying element in the base scale protectiveness was also discussed in the context of the Cr2O3-based scale stability.

Jan 1, 2017

By Vic Briccardi

Energy Management Challenges The Holistic Standard to Energy Management Energy Management Information System (EMIS) "Best Practices?: Energy Management Maturity Curve De Beers Canada Profile & Mine Locations Significant ROI Driven by Real-Time Energy Visibility Mining Energy KPI?s Summary: What Does EMIS Deliver? Q&A Session

May 1, 2013

By E. Roman E.

A novel anode slime purification process was developed and tested at pilot scale in the Chuquicamata Refinery. The process consists of three main stages: First, an atmospheric alkaline leaching at 90°C, under controlled pH and ORP operation parameters where metalloid impurities are preferentially removed from the anode slimes with high efficiency. In a second stage, alkaline washing of the mud leached with addition of reducing agent, with the intention of reducing the silver of the AgCl to metallic silver releasing the chloride, and finally, copper and other remaining impurities are leached out in mild conditions (60°C, one hour in sulphuric acid). In a side process Se, Te, and Sb are recovery with high efficiency from the alkaline liquor as chemical grade products. The global balance shows a high mass loss yielding a final product with high precious metal and low impurities content showing advantages in both a technical and economic point of view with a clear environmental sustainability. This treatment allows either the direct sale of the purified anode slimes or its pyrometallurgical treatment to obtain metal doré without emissions of Se, Sb and As. Chemical mechanisms for this novel process are also described.

Jan 1, 2007

By Jason Prno

Context ? Climate change an issue of global significance ? Research is lacking ? Study initiated by the David Suzuki Foundation, led by ArcticNorth Consulting Industry Surveying ? 34% and 48% of respondents indicated climate change is already affecting operations ? Majority believed climate change would have negative impacts in the future ? Cost and uncertainty of Future impacts are major barriers to adaptation

May 1, 2010

By W. Petruk, D. R. Morris

"The lead concentrate produced from the volcanogenic base metal ore of Brunswick Mining and Smelting in New Brunswick contains major to trace amounts of iron, zinc, cadmium, arsenic, antimony, copper, silver, selenium, tellurium, bismuth, sulphur, tin, indium, mercury and manganese as impurities. When the concentrate is sintered some of these impurities enter a variety of oxide phases, whereas others precipitate as metals. In the lead blast furnace the oxide phases decompose and the impurities recombine 10 form new phases, most are eventually discharged to the slag. The metals of the sinter remain as metals in the lead blast furnace where even more are produced, and are discharged largely with the lead bullion,IntroductionMany lead concentrates are produced from volcanogenic base metal ores . Such ores contain a wide variety of trace minerals and trace elements , therefore, concentrate s obtained from them will contain the trace elements as impurities . The impurities in the lead concentrate from one such ore, the Brunswick No. 12 deposit of Brunswick Mining and Smelting Corporation (BM S) in the Bathurst area in New Brunswick , were studied as pan of a larger investigation that was conducted to determine the extent of chemical reactions of the sinter within the lead blast furnace(1,2) The lead concentrate was investigated to identify the host mineral s for the impurities, the lead sinter was studied to identify the host phases, and frozen products from different depths within the BMS blast furnace at Belledune, New Brunswick were studied to determine the behaviour of the impurities.T he investigation was performed by pre pa ring polished sections o f the samples and studying them with a reflecting microscope, a scanning electron microscope (SE M) equipped with a Kevex energy dispersive X-ra y analysis system, a microprobe, and a Quantimet 720 image analyzer. The samples were also analyzed by X-ray diffractometer, and individual grains were analyzed by the Debye-Scherrer X-ray powder film method."

Jan 1, 1985

By O. Bernal

The Sociedad Minera Cerro Verde S.A.A, a subsidiary of Phelps Dodge Mining Company, operates a copper mining facility located in southern Peru. This "mine-forleach" operation currently produces 90,000 mtpy of copper cathode from secondary sulfide ore utilizing crushing, leaching, solvent extraction and electrowinning processes. The leach solution handling and application rates have undergone constant development over the years. This paper discusses the improvements in leach application designed to: 1) satisfy the needs of the "lixiviant request rate", which requires the use of application rates as low as 3.5 L/h/m2 and as high as 15 Llhlm2 with variable rest periods according to the leach kinetics, and 2) alleviate the poor solution distribution on the surface of the leach heaps inherent to drip emitters. Low application rates result in poor surface solution distribution and the formation of upside down cones of dry, non-leached material in the top meter of stacked ore, with heavy jarosite and iron salt precipitation; moreover, ferric iron is lost as insoluble precipitates. On the other hand, high unit flows associated with poor agglomerate quality can lead to uneven solution flow patterns within the heap leading to solution short-circuits, fines migration, and ponding with adverse effects on acid consumption and recovery.

Jan 1, 2007

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By Rob Kelso

The PISCES Goals ? To conduct research and develop programs to enable and promote planetary surface exploration ? To host international tests and technology demonstrations at the PISCES Test Site. ? To promote STEM education, inspiring students by connecting Hawaiian culture to space exploration and settlement. - economic and workforce development ? To involve the commercial sector, spinning off technologies to help the local Hawaiian economy. ? To develop a full-scale, technically valid, analog lunar/Martian outpost on Hawai`i Island.

May 1, 2013

By W. Wallace

The aerospace industry celebrated 100 years of powered flight in 2003, and the remarkable achievements that have occurred during the past 100 years are in no small way due to major developments in materials. Modern alloys for airframes, engines and other major sub-systems have evolved through the intelligent application of new processing concepts involving melting, casting, hot and cold working, heat treatment and more recently vapour phase processing. Alloy design has evolved in parallel to allow maximum benefits to be achieved from these processing advances. However, the pace of development seems to be slowing and future gains are likely to be made by learning how to extract major value from aerospace assets. Understanding the modes of deterioration and establishing cost effective lifetimes by holistic life cycle management seem to be the way of the future. Extending component lifetimes by repair, rejuvenation and refurbishment are all viable possibilities and they offer great opportunities for Canada, which, traditionally, has been a major user of modern aerospace materials rather than a supplier. The challenges for metallurgist, physicists and engineers will be no less than in the past and should create new business opportunities for Canada. The scenario described above will be developed by calling upon examples drawn from the author's experience.

Jan 1, 2004

By Ron Doucet

Industry today is now more than ever dependent on its assets and on the standard of maintenance. Changes in technology, environmental regulations, a continually improving focus on safety and global competitiveness has made maintenance a key activity in sustaining safe, financially viable and environmentally integral operations. Maintenance used to be looked upon as a cost centre with a sole focus of fixing equipment to attain high availability. Maintenance today affects all aspects of the business: safety, environmental integrity, energy efficiency, productivity, costs, and product quality. These new demands on the function of maintenance requires us to think vastly differently about what maintenance is all about, even to the point of contradicting old beliefs. In the following paragraphs we will examine some of the changed thinking that has evolved over the last 50 years. These new concepts will lay the foundation for the implementation of 21st century best practice maintenance.

May 1, 2003