Search Documents

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By Anton Sizo, Alexey Klyashtorin

The Gunnar uranium mine operated from 1953 to 1961 on the shore of Lake Athabasca, in 1964 the site was abandoned, and the mine pit flooded. In 1981, the pit was found to be stratified with a chemocline at ~70 m by a sharp change in conductivity and TDS. The uranium concentration was ~700 μg/l on the surface, 320 μg/l at 50 m, and 2,900 μg/l at 110 m. The Ra-226 concentrations were 0.1, 0.06, 0.12, and 0.4 Bq/l. By 2017, the chemocline was ~60 m deep. The highest uranium concentration was 1150 μg/l and the lowest concentration (220 μg/l) was attributed to the chemocline. In the deeper column, the uranium content varied around 750 μg/l. The uranium distribution down the pit profile was aligned with DO, ORP, and TDS. Ra-226 averaged to ~0.4 Bq/l, Ra-226 and uranium profiles were inversely related with the respective maximum and minimum attributed to the chemocline. The uranium and radium amount accumulated in the pit by 2017 was 3,420 kg and 2,163 GBq, respectively. The uranium and radium apparent accumulation trend estimates to 64 kg/y and 41 MBq/y, respectively. A stable chemocline and no concentration gradients in the other parts of the pit suggest that the contaminants are unlikely to inflow from the bottom opening or outside the pit, but rather are mobilized from the pit walls. The contaminants are not in a steady state, and concentrations of both uranium and radium are likely to increase slowly in the future if no remediation occurs.

Jan 1, 2020

By A. Sutherland Brown

"The Red Rose Mine is in the Rocher Deboule Range, 8 miles south of Hazelton. The mill camp (elevation 4,000 feet) is on Red Rose Creek, 11 miles by road from Skeena Crossing. The mine camp is one mile northeast and 1,600 feet above the mill camp on a spur of Red Rose Peak.The Red Rose mine was described in the Jubilee Volume, Structural Geology of Canadian Ore Deposits (Davis, pp. 129-131), but regional geology and mine development have progressed to a stage at which a more complete description is possible.The property was first located in 1912, and for the next 7 years was prospected actively for gold and copper on the southern extension of the Red Rose shear. Scheelite was first discovered in the vein in the northern part of the shear in 1923. The Consolidated Mining and Smelting Company of Canada, Limited optioned the property in 1939, and after a drilling program in 1940 the present mine development was initiated in the vein in the northern part of the shear. A 75-ton-per-day mill started operating early in 1942 and continued until 1943. The property was inactive until 195 l, when Western Tungsten Copper Mines Limited leased the property from The Consolidated Mining and Smelting Company of Canada, Limited. A mill, which later was enlarged to 140 tons per day, started operations at the end of 1951. The mine and mill were closed in December, 1954.The mine has twelve levels and sub1evels, and most of the workings are in the plane of the vein (see Figure 2a). The level interval is not constant, but between the lower four levels is 87 feet (100 feet in the plane of the vein). Access is provided by four adits; the 800 (elevation 5,659 feet), 600 (5,920 feet), 300 (6, 133 feet) and 200 levels (6,237 feet). The 600 level is the main haulage, and from it the ore is transported to the mill by aerial tram. From this level an inclined shaft extends in the vein to the lowest level (I, 100)."

Jan 1, 1949

By P. Hajiani

"Feasible and sustainable separation of lanthanides outside of China has been a dilemma for the past few years. The present technique uses REE electrophoretic mobility (Ui) variation in an electrical field to separate them. The present invention relates to a system and a method to separate and refine rare earth elements/compounds produced in hydrometallurgical processes while they are dissolved in an acidic medium, without any intermediate precipitation step. This process uses free-flow electrophoresis to isolate REE from the concentrate simultaneously without any pre-treatment or intermediate steps related to the nature of elements.INTRODUCTIONRare earth elements (REE) invariably occur together in nature, and any given mineral contains several or most of them. Production of high purity individual rare earth (RE) elements/compounds from their ores generally requires two stages of processing, including mineral processing and hydrometallurgy.Depending on the ore, mineral processing and hydrometallurgy treatment of the ore before REEs purification is relatively simple and quite achievable though conventional methods. However, producing individual REE from mixed REs compounds is tremendously tedious. RE processing often requires dozens of steps, each resulting in minute improvement in the complex RE streams. Separating and extracting a single REE requires a great deal of time, resources, and expertise. Today, advanced RE refinery facilities cost hundreds of millions of dollars to build. The high purity RE concentrates are separated into individual REE using solvent-based or ion exchange methods. Although there are several techniques to separate REEs, most of them suffer from different types of drawbacks. For instance, solvent extraction requires a great number of steps to achieve high purity REEs. The process which uses ion-exchanger for separation and refinery operates with low REE concentration in solution which leads to very large liquid volume quantity, bulky tanks, dehydrators, pumps, etc. The low concentration will adversely affect the water consumption as well as other chemicals. Similar chemical properties of those three valent elements do not allow them to be isolated easily one from one another using conventional separation techniques. Solvent extraction has been successfully applied for rare-earth refining (lanthanide, scandium and yttrium) for the past few decades in China. Since then, efforts have been dedicated to develop other techniques which could be applied industrially around the world."

Jan 1, 2016

By G. A. McGuffin

"IntroductionWITH the increase in quantity of sour gas reserves in the Province of Alberta, and the wider market for sulphur brought about by mounting world demand and restrictions placed on the principal supply, it was inevitable that this important source of sulphur would be .developed. In the light of these facts, it seems timely that a general paper on sulphur recovery from petroleum gases be presented. This, then, is the purpose of the following text. A short discussion of each of the following subjects is presented:(1) Properties and uses of sulphur(2) Existing sources(3) Market research(4) The recovery process in Turner Valley(5) Hazards of sulphur productionNo pretext of originality of material is made since innumerable reports have been prepared on this and related topics and information contained in these has been used quite liberally.Properties and uses of SulphurSulphur is a non-metallic element having an atomic weight of 32.06. The stable crystalline form at atmospheric temperature is referred to as 'rhombic' sulphur. It is bright yellow and has a specific gravity of 2.05, equivalent to 129.2 lb./cu. Ft. Above 204°F. sulphur has another stable crystalline form, referred to as 'monoclinic'. This is reddish-brown and is slightly less dense than the rhombic variety (122.4 lb./cu. Ft.). Sulphur in bulk form weighs 84 to 90 lb. per cu. Ft. Sulphur melts at approximately 240°F. to a straw coloured liquid which is quite viscous."

Jan 1, 1952

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Shigeto Kuroiwa, Eri Takida, Tsuyoshi Hirajima, Masashi Yamane, Yuji Imaizumi, Mitsuru Sawada, Keiko Sasaki

Selective flotation of molybdenite and chalcopyrite using various oxidation treatments (i.e., ozone treatment, hydrogen peroxide, and Fenton-like reagent) was studied in this work. It was found that ozone treatment produced a depressing effect on both minerals, resulting in a lower separation of both minerals. On the other hand, oxidation treatment using hydrogen peroxide (H2O2) and Fenton-like reagent could deliver selective oxidation on chalcopyrite surface and depress its floatability. However, bench-scale copper- molybdenum (Cu-Mo) flotation tests show that oxidation treatment using H2O2 required a higher dosage of H2O2 and a longer treatment time in order to deliver comparable flotation results to that of conventional Cu- Mo flotation using NaHS treatment. On the contrary, Fenton-like reagent could deliver selective Cu-Mo flotation results comparable to that of NaHS treatment at a lower dosage of H2O2 and a shorter conditioning time. Contact angle measurements and X-ray photoelectron spectroscopy (XPS) analysis were employed to understand the depressing mechanism of these oxidation treatments. It was found that the chalcopyrite surface covered by various oxidation products that render the surface hydrophilic. Meanwhile, the surface of molybdenite was slightly oxidized, making the surface remained hydrophobic. INTRODUCTION Molybdenite (MoS2), the main source of molybdenum, is associated with copper sulfide minerals, mainly chalcopyrite (CuFeS2), as a trace mineral. Molybdenite is a valuable mineral and plays an important role in making the copper-molybdenum (Cu-Mo) processing plant economically viable (Laskowski, Castro, & Ramos, 2013). Therefore, it is important to recover molybdenite efficiently and effectively and separate it from copper minerals. Conventional separation of copper and molybdenum minerals is usually carried out in selective Cu- Mo flotation process using a copper depressant (i.e., sodium hydrosulfide (NaHS), Noke’s reagent, or cyanides) (Ansari & Pawlik, 2007; Bulatovic, 2007). However, this process still suffers due to imperfect molybdenum recovery. Moreover, the copper depressants use in this process are toxic and harmful to the environment. As alternative, various methods have been developed to replace these toxic and hazardous depressants, for example, by synthesizing new non-toxic or low-toxic depressants or by using various oxidation methods such as sodium hypochlorite in an alkaline medium, manganese dioxide, oxygen, and plasma pre-treatment (United States Patent Office Patent No. US 2559104 A, 1951; Patent No. US2238250 A, 1941; Barzyk, Malysa, & Pomianowski, 1981; Hirajima et al., 2014). However, the oxidation phenomenon and mechanisms are still not clear since detailed surface analyses have not done and the plasma pre-treatment method is facing technical issues for industrial scale application.

Jan 1, 2019

By L. Avramovic, B. Han, R. Jonovic, Z. Stevanovic, K. Haga, S. Dimitrijevic, A. Shibayama, L. Godirilwe, Y. Takasaki

Pyrite (FeS2) and chalcopyrite (CuFeS2) which could not be recovered, are present in mine tailings discharged from Bor copper mine. About 0.3% of copper (Cu) is contained in these tailings, therefore it can be considered as a useful copper resource. At the same time, pyrite is known to promote acid mine drainage, therefore it is necessary to detoxify the tailings. An efficient method has been proposed to recover copper and reduce the environmental impacts of tailings by a combined hydrometallurgical process of high pressure leaching (HPL), solvent extraction (SX) and electrowinning (EW) process. HPL process yielded high copper leaching rate (>95%) when water (H2O) was used as a leaching media. On the other hand, pyrite contained in the tailings was converted to iron oxide by high pressure leaching. Stability evaluation of the residue obtained from high pressure leaching, confirmed almost no elution of metal ions. The percentage of copper extracted and stripped from the Cu-loaded organic phase reached 97.4%. Moreover, it was confirmed that a low iron concentration in the electrolyte of copper electrowinning, resulted in the improvement of current efficiency of copper electrodeposition. INTRODUCTION Mine tailings are a by-product obtained from the flotation process and there are billions of tons of already existing tailings all over the world. Moreover, several billion tons of additional copper tailings will inevitably be produced in the coming years (Onuaguluchi & Eren, 2012). With the declining average copper ore grade, alternative sources of copper are highly sought, mine tailings have a comparable copper grade to that of low-grade ores (0.2–0.3%) therefore, it can be said that copper mine tailings present a very important source of secondary raw material for copper production (Antonijevi´c et. al., 2008). Consequently, it is necessary to confirm the possibility of the valuable metals (such as copper) recovery from mine tailing in which copper content is about 0.2–0.3%. Our group investigates the flotation and high pressure leaching processes for recovering of copper from mine tailings. Previous work on related samples include copper and nickel flotation tailings from Botswana, and a low–grade copper ore sample from Chile. Impurities, which are associated metals in mine tailing such as iron (Fe) and aluminum (Al) co-dissolve into the solution during the HPL treatment process. Therefore, separation of copper from impurities is necessary for selective extraction of copper from mine tailings and upgrading the copper concentration in the leachate to enable further purifying of Cu by electrowinning. Thus, it is important to investigate the possibility of applying solvent extraction for concentration of copper from leachate solutions of mine tailings (Onuaguluchi & Eren, 2012; Antonijevi´c et. al., 2008). In this study, LIX-84I was used as an extractant of copper from the leachate of high pressure leaching of mine tailing. As a fundamental solvent extraction investigation, the extraction behavior of copper was studied using a simulated solution of the leachate from the high-pressure oxidative leaching of mine tailing. The effects of; solution pH, extraction time, extractant concentration and phase ratio on copper extraction and sulfuric acid (H2SO4) concentration on stripping were investigated.

Jan 1, 2019

By X. J. Guo, H. X. Li

The biological heap leaching at Zijin copper mine is currently the largest industrial application of biohydrometallurgy and one of the earliest mines to develop biological metallurgy technology in China. Since 2001, through demonstration plant and different expansion stages, it has been developed to produce 20,000 tons cathode copper annually. However the ore grade of heap leaching gradually decline year by year with copper grade average at around 0.23% now. The copper mineral is mainly the secondary copper sulfide, and symbiosis with higher content pyrite, the sulfur and iron contents is about 15 times as copper in the ore (S/Cu>15), so the acid and iron treatment of leachate, extractant and acid mine waste water is a great challenge. Combined with located in the rainy area of southern China, huge amounts of over 10 million cubic meters acid drainage need to be treated every year, so the recovery of copper from waste water as well as low grade ore is one of the characteristics of this process. This paper in general introduced the operation of heap leaching, solvent extraction, stripping and electrowinning process in Zijin mine, summarized the experience of production and technical practice, and discussed the methods of heap construction, leaching rate enhancement, third phase formation and treatment, mine effluent treatment, resource recovery and heap slope reclamation. INTRODUCTION The Zijinshan gold and copper mine is located in southeast China, Fujian province, and the typical distribution characteristics of gold and copper deposit are "upper gold and lower copper", both are large porphyry deposits. By the end of 2017, the accumulated proven reserves of available gold resources were 318 tons, copper are 2.15 million tons, and the prospective reserves of copper are more than 5 million tons. The gold mining is open pit while the copper mining is open pit and underground. The cut-off grade of gold mining is 0.15 g/t, and that of copper mining is 0.15%. A large number of very low-grade gold ores (grade <0.30 g/t) adopt a combined ore-dressing process of “partial crushing/ore washing/reprocessing/heap leaching (overlying)/ carbon slurry" independently developed, while flotation and bio-heap leaching are adopted for copper mine. Among them, copper ore with more than 0.25% copper content enters the flotation system to produce copper concentrate, while that of less than 0.25% copper content is processed by bio-heap leaching, solvent extraction and electrowinning. Zijin biological heap leaching plant is the first mine in China to achieve the scale of annual output of ten thousand tons of cathode copper since 2006. In 2008, the solvent extraction and electrowinning system were expanded, now with a daily processing capacity of 20,000 tons of ores, an annual output of 20,000 tons of cathode copper, the expanded plant is the largest biohydrometallurgy plant in China.

Jan 1, 2019

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By T. C. Holmes

Introduction The Dome mine, in the Porcupine mining camp of northern Ontario, is one of the important gold mines of the country, having produced over 139 million dollars worth of gold from the commencement of production in &apos;1910 to the end of 1944. The geology of the mine is complex and a number of types of ore are known, each occurring under particular conditions. The mine workings are very extensive and by far the greater part of them have been geologically mapped only in reconnaissance fashion. By 1940, when the writer joined the mine staff, the orebodies in the sedimentary trough and the &apos;nose&apos; orebodies, the first types to be developed, were almost worked out and many workings were inaccessible, so the descriptions of these types are based largely on study of the plans and records. The same applies to a lesser extent to some other types. At various places in this paper, statements are made as to the mineralogical or chemical composition of the rocks. Most of these determinations are based on examinations made with a hand lens and cannot, therefore, be regarded as very reliable. General Geology As there are several types of ore in the mine, occurring under quite diverse conditions, a brief outline of the geology is given here, sufficient to provide a general picture into which the fuller descriptions given with each type of ore can be fitted.

Jan 1, 1947

By The Mill Staff

Professor H.E.T. Haultain: Table 4, on page 131 of this paper, gives the assays of sized mill products. I am sure that there are many others besides myself who would be very interested to learn how the sizes 0-3 and 3-13 microns were obtained. * * * Mr. Del Davis, Mill Superintendent, Flin Flon Concentrator, on behalf of the authors of the paper, has kindly sent us the following information in reply to Professor Haultain&apos;s enquiry. Sub-Sieve Sizing by Sedimentation Procedure (As used by R. J. Digney & J. E. Ryan, 1940) Fractionation of Sub-Sieve Sizes General Method: A 1,050-gram sample of the material was pulped to 3 liters; 10 c.c. of sodium silicate and 0.2 grams of Na2C03 was added and thorough agitation given for two hours previous to settling. The material was assumed to consist wholly of particles of the same density as the most abundant particles. The time required for a particle of the upper limit of the lowest size-range to be separated, to fall a specified distance was calculated according to Stokes Law. The pulp was poured into the settling apparatus and, when the calculated time had elapsed, the suspended material was drained. The settled sediments and the process repeated until no more suspended material was obtained. The next larger size fraction was obtained in a similar manner, using the settled sediments which had been stripped of all smaller sizes as above. The fractions were arbitrarily set at 0-3, 3-13, 13-23, 23-33, and 33-43 microns (43 microns = 325 mesh).

Jan 1, 1946

By T. S. Wanne

Tunnel sealing experiment (TSX) was conducted between 1997 and 2004 in the Canadian URL located in Manitoba. In the experiment, a tunnel was excavated parallel to the maximum principal stress direction, filled with sand and sealed with bulkheads at both ends. It was then pressurized and heated by injecting hot water. The rock mass response was monitored with seismic methods. The main interest in the numerical simulation was the damage formed during the heating phase. The large-scale PFC2D models replicated a central plane- strain section of the TSX chamber. The models captured the first-order phenomena observed in-situ displaying the difference in the damage in the roof and floor regions, respectively. This difference was due to the filling material confinement of about 100 kPa on the tunnel floor, which occurred in the course of the heated experiment.

May 1, 2009

By R J. Tremblay, R. R. Hoffman

This paper deals with materials of construction and problems encountered and overcome in leaching and filtration of oxidized sulphuric acid slurry in the Port Radium mill after eight years of operation. The slurry is characterized by a high calcium sulphate content as well as a high chloride level under oxidized conditions, both of which affected initial design and subsequent changes. Leach agitation tanks are of wood with a mild steel superstructure and stainless steel agitator and moving parts below solution level. Electro-polished 316 stainless steel cooling coils are used for temperature control of the slurry. The string filters are of the Oliver type with wood decking. Extensive use is made of wood, Linatex lined mild steel and stainless steel for the slurry handling. A typical analysis of the slurry solution follows:(pH-1.30) ClOa Fe+++ Free Acid UaOs c1-so.--0.10 gms/litre 10.2 gms/litre 6. 7 gms/litre 3.5 gms/litre 2.0 gms/litre 155 gms/litre

Jan 1, 1961

By R. B. Anderson, N. J. Sherren

The mining equipment at the Scully Mine, Wabush, consists of approximately twenty-five large haulage units, eight large dozer-loader applications and seventy other related pieces of service and maintenance equipment. This equipment is operating in sub-Arctic conditions. This pa-per presents a description of the tire maintenance procedures in use here and discusses the tire troubles that are being encountered and the methods of dealing with them.

Jan 1, 1969

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By George W. Bain

The area in Quebec immediately north of the Ottawa river is underlain by a large area of granite gneiss intruded in lit-par-lit fashion into Grenville sediments and low silica intrusives of the Buckingham Series. This complex of metamorphic rocks is intruded by a much later magma found, chiefly, as a very large stock about 20 miles in diameter and extending from Brownsburg to Grenville, and as dykes and small outliers at various places adjacent to its outer margin. 1A similar stock at Rigaud, Quebec, is situated south of the Ottawa river and has been described by O. E. Le Roy. The earliest representatives of the later magma are a series of granodiorite dykes characterized by abundant hornblende, along with primary magnetite and subordinate sulphides scattered as roundish grains through anorthoclase and aligoclase feldspars and subordinate quartz. The rock is found as narrow dykes and shows no prominent secondary structures, either in the field or in thin sections under the microscope.

Jan 1, 1926

This paper states how alloy and welding advances have made possible the rapid development of the use of aluminum in the construction of equipment for earth moving and off -highway rock hauling. The main details are given regarding the construction and field testing carried out on an aluminum prototype body. The test results of strain gauge readings are analysed, and a description is given of how these have been applied in subsequent designs. The increase in the number of aluminum units put into the various types of service in Canada, as well as the problems encountered, is described, and the experience gained from five years of field service is discussed in some detail. An assessment is also made of the durability of the e units. The economics of using aluminum, together with the current development position, are reviewed, and predictions are made for considerable future increases in the use of aluminum units in open-pit and off-highway operations.

Jan 1, 1964

During industrial copper electrowinning, a fraction of the electrolyte becomes entrained with the oxygen gas bubbles that are evolved at the anodes. The fraction of entrained bubbles increases from the bottom of the anode to the top, resulting in a bubble distribution that appears as an inverted wedge between the cathode and anode. Since the bubbles act as insulating spheres, electrolyte resistance increases from the bottom of the electrodes to the top resulting in correspondingly higher local current densities and uneven copper growth along the cathode. To counter-act the inherent tendency toward excessive copper growth near the bottom of the cathodes, the use of tapered anodes was examined. The potential improvement in cathode current distribution was evaluated by comparing the primary current distributions for 2-D computer models of a copper electrowinning cell with plate shaped anodes against one with tapered anodes.

Jan 1, 2007

By E. W. Johnson

"The current increase in gold price may presage a resurgence of gold milling plants in Canada similar to that of the thirties. Because the industry has been at a low ebb for almost two decades, future operating responsibilities will likely devolve upon personnel with limited cyanidation experience. My comments, which may seem elementary to experienced operators, are directed towards these industry newcomers to highlight operational features in cyanidation which forty years' experience has shown me to 0e of importance. A brief review of what actually takes place in a cyanide circuit may help give a better understanding of the topics to be discussed.These will include: (1) expose the gold (2) dissolve the gold(3) make solid/liquid separation(4) recover the gold from solution.1. Expose the GoldThe chemical key to gold recovery by cyanidation lies in the ready solubility of the metal in a relatively weak solution (0.04%-0.075% NaCN equivalent by weight) of calcium or sodium cyanide. Obviously, dissolution cannot start unless the cya1ide is in contact with the gold. As an analogy, the yolk of a hard-boiled egg can oe taken to represent the gold particle and the egg white and shell, the surrounding gangue or sulphide host. As the sl1ell and white must be fractured to expose the yolk, similarly the surrounding gorngue or sulphide host must be broken or fractured to enable the cyanide solution to contact the gold."

Jan 1, 1979

By Max W. Ball

YOU have been kind enough to ask me to speak to you on "The War and Anglo-American Relations." A speaker always takes the liberty of putting his own interpretation on the scope of his subject. I am going to exercise that privilege, and try to look back over a generation of Anglo-American relationships and forward beyond the present war. I should like particularly to consider responsibilities as well as relationships. A more accurate caption for what I am going to say would be "Anglo-American Responsibilities.?? THE WAR WILL BE WON I am assuming that sooner or later we shall win this war. History and economics point to the same conclusion, that Germany has attempted the impossible and that the seeds of defeat are already sown. As to one ecof1:omic factor, I am already on public record as believing that Germany&apos;s oil supply is inadequate for the war she has launched. That opinion is unchanged. Aside from such tangible factors, moreover, I am convinced that the spirit of freedom is unquenchable, and that no combination of powers will be able to rout it from the British Commonwealth of Nations and the United States. Stronger even than this conviction is my faith in a God who will not suffer the defeat of man&apos;s aspiration to be master of his own soul. I am sure that all of you share that faith, and that we need not argue it. We can start with the assumption that the war will end in victory. The subject we are to consider, then, is the relationship of the English-thinking peoples during the conflict, and their joint responsibilities in the difficult days that will follow it. A CANADIAN-AMERICAN No talk on such a subject is worth listening to unless the audience knows the background and fundamental beliefs of the speaker. No human statement stands alone; behind and beside and within it are the ideals and the bias of the man who makes it. Because I am a stranger to most of you, I am constrained to talk about myself before I talk about more important matters. The review may be profitable, not because of the subject, but because it may illustrate the evolution of an attitude toward England.

Jan 1, 1941