Search Documents

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

By F. Chiesa

Forty aluminium A356 castings were poured on a Low Pressure Permanent Mould industrial machine, 500x700mm in platen size. The 152mm wide casting comprised three steps, 25mm, 13mm, 6mm in thickness and a 2.5mm overflow which allowed to assess the thin wall capability of the process. The casting campaign, which produced 40 parts, allowed to test the influence of various production parameters including the time of application of the pressure in the crucible, artificial cooling of the mould and casting rate. The thermal history in the mould was recorded over the 40 cycles, which allowed to construct a reliable thermal model of the mould/casting assembly. The metallurgical quality of castings representative of the various conditions was assessed in the 25mm, 13mm and 6mm plates. This included measuring the level of microporosity, the dendrite fineness (DAS), along with the tensile properties in the T6 condition. The radiographic quality per ASTM E155 was also determined. Modelling filling and solidification allowed to verify the validity of the predictions based on available relationships relating microporosity, secondary dendrite arm spacing (DAS) and local tensile properties (Quality Index, Q) to the local thermal solidification parameters.

Jan 1, 2007

By Z. Gostynski

The paper is a historical cross-section through a 28-year period of operation of the direct-to-blister Flash Smelting Furnace in the KGHM Glogów Copper Plant. It presents the origin of the furnace as well as the path of numerous changes and modifications both in technology and process introduced in the furnace in response to the production and cost-reduction challenges. The authors provide justification of the statement that continuous improvement of the "Polish" Flash Smelting Furnace has ranked it among the most modem smelting units in the world.

Jan 1, 2007

By Farnham. G. S.

It is difficult co know how to deal with this subject before a group having such mixed interests. The mining man is not coo concerned with the problems of alloy research. The engineer is more interested in properties of materials than how these properties can be achieved. The business man feels that scientific history and prognostication are not for him, predicting trends or possible developments in the economic field being a more than sufficient occupation. Yet the application of physical metallurgy research to industry is of importance to miner, engineer, and business man, for only through such application can the continuing existence of industries manufacturing or consuming metals be assured. History shows that hard work does not guarantee industrial survival. For instance, the Bessemer method of steel making superseded puddling operations; it, in its turn, has been largely displaced by open-hearth processing; later, steels made in electric-arc furnaces displaced open-hearth products in the quality field; and now, very specialized steels are being made in high-frequency rather than in arc furnaces. It is apparent then, if industry is co remain healthy, complacency must give way co imaginative planning, based on a thorough knowledge of production technique, a knowledge supplied by efficient research.

Jan 1, 1947

By V. Loya

Metallic foams (MF) are relatively new materials with a combination of attractive properties (permeability, high surface area, thermal and chemical stability, etc,), They can be produced from different materials and can be manufactured using various processes, Due to their unique properties, they find applications in different sectors of engineering, such as energy absorption, filtration, heat dissipation, etc, For many applications, the permeability is an important parameter to characterize and optimize, Most of the recent literature on the subject studied the permeability in the low velocity range. The present study was carried out to have a better understanding of permeability for greater velocity ranges, An equipment was designed and built for this purpose, Pressure drop measurements were made across the thickness of open-cell nickel foams, Pore and window sizes were measured by image analysis on SEM micrographs, The experimental results are in relatively good agreement with the Hazen-Dupuit-Darcy model (R2>98%), The permeability is affected by pore size, porosity and the normalized projected area of the connecting pores (ie. windows).

Jan 1, 2005

By Omkar N. S. Beruar

Extraction of sill pillars has always been problematic because of high risk of seismicity and rockburst. Depending on a number of factors, a sill pillar can undergo different failure modes and cause problems in the mine. Of these, sudden and uncontrolled failure of part(s) of the pillar leading to highenergy seismic events and rockbursts is a main concern because it is not possible to predict the location and time of a rockburst apart from its potential to cause extensive damage to the mine structures. To date, a comprehensive technique for sill pillar design and recovery does not exist. Conventional methods of pillar design, such as the pillar stability graph method, are utilized to design stiff sill pillars. In these design approaches, the post-peak response of the pillar-rock system is not considered. This is in part due to a lack of clear and comprehensive understanding of the post-peak behaviour and failure mechanism of sill pillars. In general, the strength of a rockmass is described using a failure criterion. When stresses reach the strength of the rockmass, the rockmass does not necessarily become unstable and knowledge of the loads alone is not enough to assess the instability conditions accurately. In fact, it is not possible to predict instability of rockmass based on the strength/stress ratio alone because instability depends not only on this ratio but also on the loading condition and loading system characteristics. The loading system can dictate whether the sill pillar will go through a stable or unstable failure process. This paper examines the influence of various parameters such as the pillar width to height ratio, the extraction rate, and placement of backfill on the Loading System Stiffness (LSS) and the Pillar Stiffness (PSS). The ultimate goal is to design yielding sill pillars that would yield in a stable manner and will reduce the risk of pillar rockburst. Plane strain finite element analysis is conducted using the generalized Hoek-Brown failure criterion with elastic-brittle-plastic parameters. Examples are given to demonstrate how to calculate these stiffness values and assess the stability condition of sill pillars. It is found that increasing the rate of extraction increases the likelihood of unstable yielding of the pillar as has been found in other studies. Placement of backfill in a timely fashion in the stopes above and below the sill pillars increases the stiffness of the loading system. This indicates that backfilling of stopes while creating the sill pillar increases the likelihood of stable yielding of the sill pillar.

Aug 1, 2013

By G. Knight

"Results of a program of dust research carried out at the Mines Branch Laboratory, Elliot Lake, indicate that dust-concentration estimates vary greatly, depending on the sampling instrument, the assessment technique and the properties of the dust cloud. The wide range of the ratio between the estimates by any pair of instruments shows that the correlation between the health hazard and dust-concentration estimates by most existing sampling instruments must be questionable. Important studies are being carried out to permit the definition of mine environments in more precise technical terms. The influence of size selection, the physical property measured, composition and sampling period on the assessment of the health hazard are discussed."

Jan 1, 1969

By S. Mohammadnejad, M. Olizadeh, B. Mehrabi

A new method using a combination of comprehensive mineralogical and analytical approach which includes optical and electrical microscopy and several analytical techniques with diagnostic leaching has been used to characterize the associations and distribution of gold in a variety of minerals from the Zarshuran refractory gold ore, NW Iran. Zarshuran ore with an average of 7.9 g/t Au-grade and about 8% arsenic with gold recovery less than 20% in direct cyanidation is considered as high arsenic, high au-grade refractory gold ore. In most of the refractory ores, gold is associated with arsenopyrite and co-para genetic ore minerals, while in Zarshuran ore; gold is associated with orpiment, realgar and arsenian-pyrite. Considering its mineralogy and As content, it can be considered as the most difficult refractory ore for characterization and processing. Results from the mineralogical examination and diagnostic leaches indicate that there is only a small amount of free gold (17-19%) that is present in cyanide-soluble sulfo-arsenides compounds, predominantly orpiment and realgar. Diagnostic leaches also indicate that little gold is occluded within the silicate structure (14%). Overall, the gold is mostly included in sulfides, arsenic sulfides and sulfo-arsenides (50%). The results also have shown how the technique can be used to gain a good initial understanding of potential metallurgical problems for a refractory gold ore.

Jan 1, 2005

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By M. K. Senicie

IN July, 1937, Asbestos Corporation, Limited, installed an automatic conveyor-belt scale at their King mine, Thetford Mines. The equipment was purchased 'on trial' and its performance has proved entirely satisfactory to the staff. The scale was manufactured by the Toledo Scale Company, of Toledo (Ohio) and Windsor (Ont.) and was installed by one of the Scale Company's engineers. The electrical recording equipment was installed by Keith Mercer, Reg'd, of Montreal, Canadian agents for the manufacturers, the Builders Iron Foundry, of Providence, Rhode Island. The recording equipment consists of a duplex weight-transmitter attached to the scale-head, a duplex totalizer with differential relays, a belt-speed compensator, a rate-of-delivery recorder, and a rate-of-delivery indicator. As it was desired to run the mill at maximum capacity, it was necessary to know the rate of feed at all times, so that any lessening of rate of feed or delays would be recorded and could be corrected. After having determined the rate of feed to the mill (100 per cent capacity), it was required to have weighing and recording instruments which would show: (1) The rate of feed per hour. (2) Any variations .in the load. (3) Any delays and the duration and time of the delays. Rate of tonnage recorders in the mill superintendent's office and at the point of feedi.ng were necessary, as was automatic control between the mill superintendent and the feed man. It was desired to have a permanent record of total tonnage fed per shift or day; weighing and recording mechanism had to have sensitivity to record all previously mentioned conditions. Mechanism had to be of rugged construction, and be so built that it would stay in good operating condition, with the minimum amount of adjustment and supervision.

Jan 1, 1938

By Ashu Garg, Anirban Bhattacharya

"Friction stir spot welding of aluminum alloy AA6061-T6 sheets was performed with circular (plunge depths 0.4 and 0.6 mm), square and triangular tool pin (plunge depth 0.4 mm) with constant 0.2 mm shoulder penetration to characterize various zones of weld nugget. It was observed that the depth of the stir zone formed below the tool pin is comparatively similar for different tool pins but wider for circular tool pin. The size of another stir zone formed at the interface of tool pin and a tool shoulder is observed to be larger for triangular and square tool pin due to the higher swept rate. Predicted strain from finite element analysis, calculated strain rate using Zener-Hollomon relationship and experimentally measured grain size distribution indicates severe amount of plastic deformation in-and-around the nugget/spot region. Finer grains in various stir zones were observed than thermo-mechanically and heat affected zones. Grain size (at distribution peaks) in stir zones varied around 2.54 µm to 3.69 µm for different tool pin profiles as compared to base metal grain size of 20 µm. Microhardness results indicate that the welded region is quite softened than base metal and maximum hardness is mostly observed around the thermo-mechanically affected zone.INTRODUCTION Friction stir spot welding (FSSW) is widely used for joining the sheets of materials like aluminum, copper, magnesium, etc. The process begins by plunging a rotating tool (generally having a pin and a shoulder) into the sheets to be welded. Continuous stirring of the tool and downward plunging force generates localized heat due to friction at the tool-sheet interface and plastic deformation of the sheet metal. The material gets softened and the plasticized material adjacent to the tool pin starts flowing due to the action of tool rotation and tool plunge thereby causing intermixing and bonding between the overlapped sheets. The tool stirring also promotes grain refinement in the weld nugget associated with high strain, strain rate and thermal cycle. The formation of new microstructure also affects the mechanical properties and efficiency of FSSW joints. Studies also showed that the tool pin design and tool shoulder feature exerts a noteworthy influence on the material flow and intermixing during the FSSW process (Reilly et al., 2015; Hirasawa et al., 2010). Sarkar et al. (2016) studied the material flow and intermixing during FSSW using tracer material method and reported that the size and width of flow zone increases with tool penetration depth. The influence of tool rotational speed on microstructure and stir zone temperature was investigated during FSSW of dissimilar AA6061-AA5754 alloys (Gerlich et al., 2007). They reported that the average grain size in stir zone of AA6061 weld increases with increase in tool rotational speed. In another work, Gerlich et al. (2008) studied the local melting and tool slippage during FSSW of Al alloys. Tool slippage was investigated by calculating the strain rate using Zener-Hollomon relation. Garg and Bhattacharya (2017a) studied the effect of dwell time, tool pin profiles and tool rotational speed on shear strength, microstructure, temperature and strain distribution during FSSW of AA6061. In another work, Garg and Bhattacharya (2017b) analyzed the effect of different tool pins and pinless tools on the shear strength and microstructure during similar and dissimilar FSSW of AA6061-T6 and pure Cu. Chang et al. (2004) proposed mathematical relationship between the average grain size and Zener-Hollomon parameter during friction stir processing of Mg alloy. Solhjoo (2010) presented a mathematical approach to determine the critical strain as a function of peak strain required for initiation of dynamic recrystallization in austenitic stainless steel. Fratini and Buffa (2005) also proposed the numerical model to determine the grain size during continuous dynamic recrystallization phenomenon."

Jan 1, 2018

By J. -F. Blais, M. -O. Simonnot, P. Charbonnier, J. Mocellin, Université de Lorraine INRA, G. Mercier

"Huge amounts of air pollution scrubber sludge have been generated during ferromanganese production using blast furnace. These residues have been historically deposited in ponds near steel making plants. They are very rich in zinc, manganese and lead (5 to 40 %) and also contain aluminum and iron. Considering the market value of these metals, brownfield sites can now be used as secondary resources. These ponds also have to be cleaned up to meet the environmental regulations.We have developed a hydrometallurgical process to recover Zn, Mn and Pb in order to produce valuable compounds of Mn and Zn and recover the final Pb residue by pyrometallurgy. The Zn and Mn compounds need to be pure enough to be economically valuable. Batch laboratory tests were carried out to determine suitable selective leaching conditions. The investigated operating conditions were acid concentration, pulp density and temperature. Optimal conditions to maximize zinc extraction (100 %) and manganese extraction (95.9 %) were found using sulfuric acid and sodium metabisulfide. The final residue contained 14.8 to 23.8 % of Pb. Then, Zn was recovered in the form of ZnO or ZnS by precipitation and Zn metal by electrowinning, while Mn was recovered as MnCO3 with a fairly acceptable concentration of impurities.INTRODUCTIONFerromanganese has been produced by pyrometallurgy in much of Western Europe for centuries. Use of wet scrubber to remove pollutant and dust particles from gas stream was common for most of these operations. Those residues contain high concentration of Zn, Mn and Pb. They have been left to decant in settling ponds installed close to the steel production plants. They now constitute heavily contaminated artificial soils. Those sludges are so contaminated with Zn, Mn and Pb that they can be used for metal production. Currently, no method is available to decontaminate these residues and recover Zn, Mn and Pb. Therefore, an approach considering these brownfield sites as secondary resource is in development. Doing so would achieve two goals, decontaminate the site and produce metals.. (Huot, Faure, Biache, Lorgeoux, Simonnot, & Morel, 2014a; Huot, Simonnot, Marion, Yvon, De Donato, & Morel, 2012; Huot, Simonnot, Watteau, Marion, Yvon, De Donato, & Morel, 2014b)."

Jan 1, 2016

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By A. Allaire

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By Wynne Potter

"On the west coast of Cape Breton Island four coal basins have been identified, varying in age and extending from Port Hood northeasterly to Chimney Corner. Those of Chimney Corner - St. Rose in the north and Port Hood in the south belong to the Pennsylvanian Riversdale Group while lying between them are the coal basins of Mabou and Inverness belonging to the younger Pictou Group. Almost all of the coal basins are submarine and coal mining was carried out on all basins at various times. The seams in all basins dip steeply seaward at angles from 10 to 20 degrees but were found to flatten seaward. The coal is ranked as a high volatile C bituminous coal. Ash and sulphur contents are high compared with Sydney coal and the coal has a tendency to spontaneous combustion when stored in large quantities.Of the four basins, the most significant is that of Mabou. At Mabou recent seismic and drilling investigations have indicated that although a sizable reserve of coal may be found offshore the structural problems, particularly faults, and the poor quality of the coal encountered will make it a resource of the future, if at all. Inferred resources have been calculated at 150 million tonnes in four seams over a 10 km2 area and extending 3 km from shore. The quality of the Mabou coals varies with ash, ranging from 5 to 25 per cent and sulphur up to 6 per cent. Calorific value ranges from 25.3 Mj I kg to 31. 7 Mj I kg. The Port Hood and St. Rose -Chimney Corner fields (Fig. 1) contain 16 million and 3 million tonnes respectively, but the Inverness basin is considered to have been depleted. The active mine in this area is the Evans Mine at St. Rose that is currently producing between 30 -50,000 tonnes a year from proven reserves of approximately 3 million tonnes."

Jan 1, 1985

By S. C. Ells

Within the Dominion of Canada occurrences of petro-liferous shales have been known for many years. Nevertheless, with the exception of a comparatively brief period, Canada has had to depend largely on foreign sources for its supplies of crude petroleum and petroleum products. Attempts were made to retort local shales in 1859, near Collingwood, Ontario, and again in 1862, near Baltimore, New Brunswick. In each instance these attempts were abandoned owing to the rapidly increasing production of well petroleum from the newly discovered pools of western Ontario and Pennsylvania. Now, after a lapse of nearly sixty years, attention is again directed to the commercial value of Canadian shales as a possible source of crude petroleum. Province of Nova Scotia: The principal deposits of oil-shales occur in Pictou and Antigonish counties and have been known for more than 60 years. During the three years following its discovery, several thousand tons of a particularly rich sub-variety, known as stellarite (stellar coal or oil coal) was mined near Stellarton in Pictou county. It is stated that stellarite yielded upwards of 10,000 cubic feet of 36 candle gas, and that selected samples gave a yield equivalent to 170 Imperial gallons (204 U.S. gallons) of crude petroleum per ton. The average petroleum content of a cargo shipped to Boston was 48 Imperial gallons (57.6 U. S. gallons) and the associated shale or 'bat', gave a yield of 39 Imperial gallons (46.8 U.S. gallons). Part of the above output was shipped to retorting works in Boston and in Portland, and part was mixed with bituminous coals for the enrichment of illuminating gas. Following the discovery of well petroleum in Ontario and in the United States, the mining of stellarite ceased.

Jan 1, 1925

By D. J. Reddish

The paper describes a case study where numerical modelling has been applied to predict potential risks associated with inflows of water in active mine workings from an overlying sandstone aquifer. The objective of the modelling was to predict the development of strata fractures and strains as the longwall panels were extracted and investigate their relationship to an sandstone aquifer. The numerical modelling study also included the investigation of the effect of mining on a fault that existed close to the start position of one of the panels. The potential effects of mining on the fault were undertaken by parametric studies adjusting properties for the fault and the relative position of extractions, which allowed the mine planner to position the panel layout accordingly.

May 1, 2003

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016